static irqreturn_t pic32_interrupt(int irq, void *hci)
{
struct musb *musb = hci;
irqreturn_t ret = IRQ_NONE;
u32 epintr, usbintr;
/* ack usb core interrupts */
musb->int_usb = musb_readb(musb->mregs, MUSB_INTRUSB);
if (musb->int_usb)
musb_writeb(musb->mregs, MUSB_INTRUSB, musb->int_usb);
/* ack endpoint interrupts */
musb->int_rx = musb_readw(musb->mregs, MUSB_INTRRX) & PIC32_RX_EP_MASK;
if (musb->int_rx)
musb_writew(musb->mregs, MUSB_INTRRX, musb->int_rx);
musb->int_tx = musb_readw(musb->mregs, MUSB_INTRTX) & PIC32_TX_EP_MASK;
if (musb->int_tx)
musb_writew(musb->mregs, MUSB_INTRTX, musb->int_tx);
/* drop spurious RX and TX if device is disconnected */
if (musb->int_usb & MUSB_INTR_DISCONNECT) {
musb->int_tx = 0;
musb->int_rx = 0;
}
if (musb->int_tx || musb->int_rx || musb->int_usb)
ret = musb_interrupt(musb);
return ret;
}
static irqreturn_t jz4740_musb_interrupt(int irq, void *__hci)
{
unsigned long flags;
irqreturn_t retval = IRQ_NONE;
struct musb *musb = __hci;
spin_lock_irqsave(&musb->lock, flags);
musb->int_usb = musb_readb(musb->mregs, MUSB_INTRUSB);
musb->int_tx = musb_readw(musb->mregs, MUSB_INTRTX);
musb->int_rx = musb_readw(musb->mregs, MUSB_INTRRX);
/*
* The controller is gadget only, the state of the host mode IRQ bits is
* undefined. Mask them to make sure that the musb driver core will
* never see them set
*/
musb->int_usb &= MUSB_INTR_SUSPEND | MUSB_INTR_RESUME |
MUSB_INTR_RESET | MUSB_INTR_SOF;
if (musb->int_usb || musb->int_tx || musb->int_rx)
retval = musb_interrupt(musb);
spin_unlock_irqrestore(&musb->lock, flags);
return retval;
}
/*
* Workaround: Sometimes the DISCONNECT interrupt is not generated in
* musb_core. Make a quick check to see it it was already handled,
* otherwise fake it.
*/
void stm_musb_force_disconnect(void)
{
unsigned long flags;
u8 i;
int try_count;
struct musb_hw_ep *hw_ep;
if (!musb_status)
return;
spin_lock_irqsave(&musb_status->lock, flags);
if (!(musb_status->int_usb & MUSB_INTR_DISCONNECT)) {
/* We probably never got the interrupt, fake it.
*
* These variables are normally filled in from
* registers by the irq handler generic_interrupt()
* before calling musb_interrupt(), so we set them to
* a desired combination and call.
*/
musb_status->int_usb = MUSB_INTR_DISCONNECT;
musb_status->int_tx = 0;
musb_status->int_rx = 0;
musb_interrupt(musb_status);
}
spin_unlock_irqrestore(&musb_status->lock, flags);
/* Wait until all endpoints will be actually disconnected,
* because in some function drivers, disconnection of endpoints
* can be postponed for later time. For example fsg_disable() from
* f_mass_storage.c does not disconnect its endpoints in fact. It just
* send signal to the its main thread to do disconnection when it
* will have a time. This is not good, because after exit from
* stm_musb_force_disconnect the clock for USB chip can be disabled.
*/
for (try_count = 1500; try_count > 0; try_count--) {
for (i = 0, hw_ep = musb_status->endpoints;
i < musb_status->nr_endpoints; i++, hw_ep++) {
if (hw_ep->ep_in.desc != NULL)
break;
if (hw_ep->ep_out.desc != NULL)
break;
}
if (i == musb_status->nr_endpoints)
break;
msleep(10);
}
if (try_count == 0)
printk(KERN_ALERT
"U8500 USB : endpoints disconnections timed out\n");
}
static irqreturn_t omap2430_musb_interrupt(int irq, void *__hci)
{
unsigned long flags;
irqreturn_t retval = IRQ_NONE;
struct musb *musb = __hci;
spin_lock_irqsave(&musb->lock, flags);
musb->int_usb = musb_readb(musb->mregs, MUSB_INTRUSB);
musb->int_tx = musb_readw(musb->mregs, MUSB_INTRTX);
musb->int_rx = musb_readw(musb->mregs, MUSB_INTRRX);
if (musb->int_usb || musb->int_tx || musb->int_rx)
retval = musb_interrupt(musb);
spin_unlock_irqrestore(&musb->lock, flags);
return retval;
}
static irqreturn_t sunxi_musb_interrupt(int irq, void *__hci)
{
struct musb *musb = __hci;
irqreturn_t retval = IRQ_NONE;
/* read and flush interrupts */
musb->int_usb = musb_readb(musb->mregs, MUSB_INTRUSB);
if (musb->int_usb)
musb_writeb(musb->mregs, MUSB_INTRUSB, musb->int_usb);
musb->int_tx = musb_readw(musb->mregs, MUSB_INTRTX);
if (musb->int_tx)
musb_writew(musb->mregs, MUSB_INTRTX, musb->int_tx);
musb->int_rx = musb_readw(musb->mregs, MUSB_INTRRX);
if (musb->int_rx)
musb_writew(musb->mregs, MUSB_INTRRX, musb->int_rx);
if (musb->int_usb || musb->int_tx || musb->int_rx)
retval |= musb_interrupt(musb);
return retval;
}
static irqreturn_t dsps_interrupt(struct musb *musb)
{
void __iomem *reg_base = musb->ctrl_base;
struct device_d *dev = musb->controller;
struct dsps_glue *glue = dev->priv;
const struct dsps_musb_wrapper *wrp = glue->wrp;
unsigned long flags;
irqreturn_t ret = IRQ_NONE;
u32 epintr, usbintr;
spin_lock_irqsave(&musb->lock, flags);
/* Get endpoint interrupts */
epintr = dsps_readl(reg_base, wrp->epintr_status);
musb->int_rx = (epintr & wrp->rxep_bitmap) >> wrp->rxep_shift;
musb->int_tx = (epintr & wrp->txep_bitmap) >> wrp->txep_shift;
if (epintr)
dsps_writel(reg_base, wrp->epintr_status, epintr);
/* Get usb core interrupts */
usbintr = dsps_readl(reg_base, wrp->coreintr_status);
if (!usbintr && !epintr)
goto out;
musb->int_usb = (usbintr & wrp->usb_bitmap) >> wrp->usb_shift;
if (usbintr)
dsps_writel(reg_base, wrp->coreintr_status, usbintr);
dev_dbg(musb->controller, "usbintr (%x) epintr(%x)\n",
usbintr, epintr);
if (musb->int_tx || musb->int_rx || musb->int_usb)
ret |= musb_interrupt(musb);
out:
spin_unlock_irqrestore(&musb->lock, flags);
return ret;
}
static irqreturn_t davinci_musb_interrupt(int irq, void *__hci)
{
unsigned long flags;
irqreturn_t retval = IRQ_NONE;
struct musb *musb = __hci;
struct usb_otg *otg = musb->xceiv->otg;
void __iomem *tibase = musb->ctrl_base;
struct cppi *cppi;
u32 tmp;
spin_lock_irqsave(&musb->lock, flags);
/* NOTE: DaVinci shadows the Mentor IRQs. Don't manage them through
* the Mentor registers (except for setup), use the TI ones and EOI.
*
* Docs describe irq "vector" registers associated with the CPPI and
* USB EOI registers. These hold a bitmask corresponding to the
* current IRQ, not an irq handler address. Would using those bits
* resolve some of the races observed in this dispatch code??
*/
/* CPPI interrupts share the same IRQ line, but have their own
* mask, state, "vector", and EOI registers.
*/
cppi = container_of(musb->dma_controller, struct cppi, controller);
if (is_cppi_enabled() && musb->dma_controller && !cppi->irq)
retval = cppi_interrupt(irq, __hci);
/* ack and handle non-CPPI interrupts */
tmp = musb_readl(tibase, DAVINCI_USB_INT_SRC_MASKED_REG);
musb_writel(tibase, DAVINCI_USB_INT_SRC_CLR_REG, tmp);
dev_dbg(musb->controller, "IRQ %08x\n", tmp);
musb->int_rx = (tmp & DAVINCI_USB_RXINT_MASK)
>> DAVINCI_USB_RXINT_SHIFT;
musb->int_tx = (tmp & DAVINCI_USB_TXINT_MASK)
>> DAVINCI_USB_TXINT_SHIFT;
musb->int_usb = (tmp & DAVINCI_USB_USBINT_MASK)
>> DAVINCI_USB_USBINT_SHIFT;
/* DRVVBUS irqs are the only proxy we have (a very poor one!) for
* DaVinci's missing ID change IRQ. We need an ID change IRQ to
* switch appropriately between halves of the OTG state machine.
* Managing DEVCTL.SESSION per Mentor docs requires we know its
* value, but DEVCTL.BDEVICE is invalid without DEVCTL.SESSION set.
* Also, DRVVBUS pulses for SRP (but not at 5V) ...
*/
if (tmp & (DAVINCI_INTR_DRVVBUS << DAVINCI_USB_USBINT_SHIFT)) {
int drvvbus = musb_readl(tibase, DAVINCI_USB_STAT_REG);
void __iomem *mregs = musb->mregs;
u8 devctl = musb_readb(mregs, MUSB_DEVCTL);
int err = musb->int_usb & MUSB_INTR_VBUSERROR;
err = musb->int_usb & MUSB_INTR_VBUSERROR;
if (err) {
/* The Mentor core doesn't debounce VBUS as needed
* to cope with device connect current spikes. This
* means it's not uncommon for bus-powered devices
* to get VBUS errors during enumeration.
*
* This is a workaround, but newer RTL from Mentor
* seems to allow a better one: "re"starting sessions
* without waiting (on EVM, a **long** time) for VBUS
* to stop registering in devctl.
*/
musb->int_usb &= ~MUSB_INTR_VBUSERROR;
musb->xceiv->state = OTG_STATE_A_WAIT_VFALL;
mod_timer(&otg_workaround, jiffies + POLL_SECONDS * HZ);
WARNING("VBUS error workaround (delay coming)\n");
} else if (drvvbus) {
MUSB_HST_MODE(musb);
otg->default_a = 1;
musb->xceiv->state = OTG_STATE_A_WAIT_VRISE;
portstate(musb->port1_status |= USB_PORT_STAT_POWER);
del_timer(&otg_workaround);
} else {
musb->is_active = 0;
MUSB_DEV_MODE(musb);
otg->default_a = 0;
musb->xceiv->state = OTG_STATE_B_IDLE;
portstate(musb->port1_status &= ~USB_PORT_STAT_POWER);
}
/* NOTE: this must complete poweron within 100 msec
* (OTG_TIME_A_WAIT_VRISE) but we don't check for that.
*/
davinci_musb_source_power(musb, drvvbus, 0);
dev_dbg(musb->controller, "VBUS %s (%s)%s, devctl %02x\n",
drvvbus ? "on" : "off",
usb_otg_state_string(musb->xceiv->state),
err ? " ERROR" : "",
devctl);
retval = IRQ_HANDLED;
}
if (musb->int_tx || musb->int_rx || musb->int_usb)
retval |= musb_interrupt(musb);
/* irq stays asserted until EOI is written */
musb_writel(tibase, DAVINCI_USB_EOI_REG, 0);
/* poll for ID change */
if (musb->xceiv->state == OTG_STATE_B_IDLE)
mod_timer(&otg_workaround, jiffies + POLL_SECONDS * HZ);
spin_unlock_irqrestore(&musb->lock, flags);
return retval;
}
static irqreturn_t dsps_interrupt(int irq, void *hci)
{
struct musb *musb = hci;
void __iomem *reg_base = musb->ctrl_base;
struct device *dev = musb->controller;
struct dsps_glue *glue = dev_get_drvdata(dev->parent);
const struct dsps_musb_wrapper *wrp = glue->wrp;
unsigned long flags;
irqreturn_t ret = IRQ_NONE;
u32 epintr, usbintr;
spin_lock_irqsave(&musb->lock, flags);
/* Get endpoint interrupts */
epintr = musb_readl(reg_base, wrp->epintr_status);
musb->int_rx = (epintr & wrp->rxep_bitmap) >> wrp->rxep_shift;
musb->int_tx = (epintr & wrp->txep_bitmap) >> wrp->txep_shift;
if (epintr)
musb_writel(reg_base, wrp->epintr_status, epintr);
/* Get usb core interrupts */
usbintr = musb_readl(reg_base, wrp->coreintr_status);
if (!usbintr && !epintr)
goto out;
musb->int_usb = (usbintr & wrp->usb_bitmap) >> wrp->usb_shift;
if (usbintr)
musb_writel(reg_base, wrp->coreintr_status, usbintr);
dev_dbg(musb->controller, "usbintr (%x) epintr(%x)\n",
usbintr, epintr);
if (usbintr & ((1 << wrp->drvvbus) << wrp->usb_shift)) {
int drvvbus = musb_readl(reg_base, wrp->status);
void __iomem *mregs = musb->mregs;
u8 devctl = musb_readb(mregs, MUSB_DEVCTL);
int err;
err = musb->int_usb & MUSB_INTR_VBUSERROR;
if (err) {
/*
* The Mentor core doesn't debounce VBUS as needed
* to cope with device connect current spikes. This
* means it's not uncommon for bus-powered devices
* to get VBUS errors during enumeration.
*
* This is a workaround, but newer RTL from Mentor
* seems to allow a better one: "re"-starting sessions
* without waiting for VBUS to stop registering in
* devctl.
*/
musb->int_usb &= ~MUSB_INTR_VBUSERROR;
musb->xceiv->otg->state = OTG_STATE_A_WAIT_VFALL;
dsps_mod_timer_optional(glue);
WARNING("VBUS error workaround (delay coming)\n");
} else if (drvvbus) {
MUSB_HST_MODE(musb);
musb->xceiv->otg->default_a = 1;
musb->xceiv->otg->state = OTG_STATE_A_WAIT_VRISE;
dsps_mod_timer_optional(glue);
} else {
musb->is_active = 0;
MUSB_DEV_MODE(musb);
musb->xceiv->otg->default_a = 0;
musb->xceiv->otg->state = OTG_STATE_B_IDLE;
}
/* NOTE: this must complete power-on within 100 ms. */
dev_dbg(musb->controller, "VBUS %s (%s)%s, devctl %02x\n",
drvvbus ? "on" : "off",
usb_otg_state_string(musb->xceiv->otg->state),
err ? " ERROR" : "",
devctl);
ret = IRQ_HANDLED;
}
if (musb->int_tx || musb->int_rx || musb->int_usb)
ret |= musb_interrupt(musb);
/* Poll for ID change and connect */
switch (musb->xceiv->otg->state) {
case OTG_STATE_B_IDLE:
case OTG_STATE_A_WAIT_BCON:
dsps_mod_timer_optional(glue);
break;
default:
break;
}
out:
spin_unlock_irqrestore(&musb->lock, flags);
return ret;
}
static irqreturn_t da8xx_musb_interrupt(int irq, void *hci)
{
struct musb *musb = hci;
void __iomem *reg_base = musb->ctrl_base;
struct usb_otg *otg = musb->xceiv->otg;
unsigned long flags;
irqreturn_t ret = IRQ_NONE;
u32 status;
spin_lock_irqsave(&musb->lock, flags);
/*
* NOTE: DA8XX shadows the Mentor IRQs. Don't manage them through
* the Mentor registers (except for setup), use the TI ones and EOI.
*/
/* Acknowledge and handle non-CPPI interrupts */
status = musb_readl(reg_base, DA8XX_USB_INTR_SRC_MASKED_REG);
if (!status)
goto eoi;
musb_writel(reg_base, DA8XX_USB_INTR_SRC_CLEAR_REG, status);
dev_dbg(musb->controller, "USB IRQ %08x\n", status);
musb->int_rx = (status & DA8XX_INTR_RX_MASK) >> DA8XX_INTR_RX_SHIFT;
musb->int_tx = (status & DA8XX_INTR_TX_MASK) >> DA8XX_INTR_TX_SHIFT;
musb->int_usb = (status & DA8XX_INTR_USB_MASK) >> DA8XX_INTR_USB_SHIFT;
/*
* DRVVBUS IRQs are the only proxy we have (a very poor one!) for
* DA8xx's missing ID change IRQ. We need an ID change IRQ to
* switch appropriately between halves of the OTG state machine.
* Managing DEVCTL.Session per Mentor docs requires that we know its
* value but DEVCTL.BDevice is invalid without DEVCTL.Session set.
* Also, DRVVBUS pulses for SRP (but not at 5 V)...
*/
if (status & (DA8XX_INTR_DRVVBUS << DA8XX_INTR_USB_SHIFT)) {
int drvvbus = musb_readl(reg_base, DA8XX_USB_STAT_REG);
void __iomem *mregs = musb->mregs;
u8 devctl = musb_readb(mregs, MUSB_DEVCTL);
int err;
err = musb->int_usb & MUSB_INTR_VBUSERROR;
if (err) {
/*
* The Mentor core doesn't debounce VBUS as needed
* to cope with device connect current spikes. This
* means it's not uncommon for bus-powered devices
* to get VBUS errors during enumeration.
*
* This is a workaround, but newer RTL from Mentor
* seems to allow a better one: "re"-starting sessions
* without waiting for VBUS to stop registering in
* devctl.
*/
musb->int_usb &= ~MUSB_INTR_VBUSERROR;
musb->xceiv->otg->state = OTG_STATE_A_WAIT_VFALL;
mod_timer(&otg_workaround, jiffies + POLL_SECONDS * HZ);
WARNING("VBUS error workaround (delay coming)\n");
} else if (drvvbus) {
MUSB_HST_MODE(musb);
otg->default_a = 1;
musb->xceiv->otg->state = OTG_STATE_A_WAIT_VRISE;
portstate(musb->port1_status |= USB_PORT_STAT_POWER);
del_timer(&otg_workaround);
} else {
musb->is_active = 0;
MUSB_DEV_MODE(musb);
otg->default_a = 0;
musb->xceiv->otg->state = OTG_STATE_B_IDLE;
portstate(musb->port1_status &= ~USB_PORT_STAT_POWER);
}
dev_dbg(musb->controller, "VBUS %s (%s)%s, devctl %02x\n",
drvvbus ? "on" : "off",
usb_otg_state_string(musb->xceiv->otg->state),
err ? " ERROR" : "",
devctl);
ret = IRQ_HANDLED;
}
if (musb->int_tx || musb->int_rx || musb->int_usb)
ret |= musb_interrupt(musb);
eoi:
/* EOI needs to be written for the IRQ to be re-asserted. */
if (ret == IRQ_HANDLED || status)
musb_writel(reg_base, DA8XX_USB_END_OF_INTR_REG, 0);
/* Poll for ID change */
if (musb->xceiv->otg->state == OTG_STATE_B_IDLE)
mod_timer(&otg_workaround, jiffies + POLL_SECONDS * HZ);
spin_unlock_irqrestore(&musb->lock, flags);
return ret;
}
static irqreturn_t dsps_interrupt(int irq, void *hci)
{
struct musb *musb = hci;
void __iomem *reg_base = musb->ctrl_base;
struct device *dev = musb->controller;
struct dsps_glue *glue = dev_get_drvdata(dev->parent);
const struct dsps_musb_wrapper *wrp = glue->wrp;
unsigned long flags;
irqreturn_t ret = IRQ_NONE;
u32 epintr, usbintr;
spin_lock_irqsave(&musb->lock, flags);
/* Get endpoint interrupts */
epintr = dsps_readl(reg_base, wrp->epintr_status);
musb->int_rx = (epintr & wrp->rxep_bitmap) >> wrp->rxep_shift;
musb->int_tx = (epintr & wrp->txep_bitmap) >> wrp->txep_shift;
if (epintr)
dsps_writel(reg_base, wrp->epintr_status, epintr);
/* Get usb core interrupts */
usbintr = dsps_readl(reg_base, wrp->coreintr_status);
if (!usbintr && !epintr)
goto out;
musb->int_usb = (usbintr & wrp->usb_bitmap) >> wrp->usb_shift;
if (usbintr)
dsps_writel(reg_base, wrp->coreintr_status, usbintr);
dev_dbg(musb->controller, "usbintr (%x) epintr(%x)\n",
usbintr, epintr);
/*
* DRVVBUS IRQs are the only proxy we have (a very poor one!) for
* DSPS IP's missing ID change IRQ. We need an ID change IRQ to
* switch appropriately between halves of the OTG state machine.
* Managing DEVCTL.SESSION per Mentor docs requires that we know its
* value but DEVCTL.BDEVICE is invalid without DEVCTL.SESSION set.
* Also, DRVVBUS pulses for SRP (but not at 5V) ...
*/
if (is_host_active(musb) && usbintr & MUSB_INTR_BABBLE)
pr_info("CAUTION: musb: Babble Interrupt Occurred\n");
if (usbintr & ((1 << wrp->drvvbus) << wrp->usb_shift)) {
int drvvbus = dsps_readl(reg_base, wrp->status);
void __iomem *mregs = musb->mregs;
u8 devctl = dsps_readb(mregs, MUSB_DEVCTL);
int err;
err = musb->int_usb & MUSB_INTR_VBUSERROR;
if (err) {
/*
* The Mentor core doesn't debounce VBUS as needed
* to cope with device connect current spikes. This
* means it's not uncommon for bus-powered devices
* to get VBUS errors during enumeration.
*
* This is a workaround, but newer RTL from Mentor
* seems to allow a better one: "re"-starting sessions
* without waiting for VBUS to stop registering in
* devctl.
*/
musb->int_usb &= ~MUSB_INTR_VBUSERROR;
musb->xceiv->state = OTG_STATE_A_WAIT_VFALL;
mod_timer(&glue->timer,
jiffies + wrp->poll_seconds * HZ);
WARNING("VBUS error workaround (delay coming)\n");
} else if (drvvbus) {
MUSB_HST_MODE(musb);
musb->xceiv->otg->default_a = 1;
musb->xceiv->state = OTG_STATE_A_WAIT_VRISE;
del_timer(&glue->timer);
} else {
musb->is_active = 0;
MUSB_DEV_MODE(musb);
musb->xceiv->otg->default_a = 0;
musb->xceiv->state = OTG_STATE_B_IDLE;
}
/* NOTE: this must complete power-on within 100 ms. */
dev_dbg(musb->controller, "VBUS %s (%s)%s, devctl %02x\n",
drvvbus ? "on" : "off",
usb_otg_state_string(musb->xceiv->state),
err ? " ERROR" : "",
devctl);
ret = IRQ_HANDLED;
}
if (musb->int_tx || musb->int_rx || musb->int_usb)
ret |= musb_interrupt(musb);
/* Poll for ID change */
if (musb->xceiv->state == OTG_STATE_B_IDLE)
mod_timer(&glue->timer, jiffies + wrp->poll_seconds * HZ);
out:
spin_unlock_irqrestore(&musb->lock, flags);
return ret;
}
static irqreturn_t am35x_musb_interrupt(int irq, void *hci)
{
struct musb *musb = hci;
void __iomem *reg_base = musb->ctrl_base;
struct device *dev = musb->controller;
struct musb_hdrc_platform_data *plat = dev_get_platdata(dev);
struct omap_musb_board_data *data = plat->board_data;
struct usb_otg *otg = musb->xceiv->otg;
unsigned long flags;
irqreturn_t ret = IRQ_NONE;
u32 epintr, usbintr;
spin_lock_irqsave(&musb->lock, flags);
/* Get endpoint interrupts */
epintr = musb_readl(reg_base, EP_INTR_SRC_MASKED_REG);
if (epintr) {
musb_writel(reg_base, EP_INTR_SRC_CLEAR_REG, epintr);
musb->int_rx =
(epintr & AM35X_RX_INTR_MASK) >> AM35X_INTR_RX_SHIFT;
musb->int_tx =
(epintr & AM35X_TX_INTR_MASK) >> AM35X_INTR_TX_SHIFT;
}
/* Get usb core interrupts */
usbintr = musb_readl(reg_base, CORE_INTR_SRC_MASKED_REG);
if (!usbintr && !epintr)
goto eoi;
if (usbintr) {
musb_writel(reg_base, CORE_INTR_SRC_CLEAR_REG, usbintr);
musb->int_usb =
(usbintr & AM35X_INTR_USB_MASK) >> AM35X_INTR_USB_SHIFT;
}
/*
* DRVVBUS IRQs are the only proxy we have (a very poor one!) for
* AM35x's missing ID change IRQ. We need an ID change IRQ to
* switch appropriately between halves of the OTG state machine.
* Managing DEVCTL.SESSION per Mentor docs requires that we know its
* value but DEVCTL.BDEVICE is invalid without DEVCTL.SESSION set.
* Also, DRVVBUS pulses for SRP (but not at 5V) ...
*/
if (usbintr & (AM35X_INTR_DRVVBUS << AM35X_INTR_USB_SHIFT)) {
int drvvbus = musb_readl(reg_base, USB_STAT_REG);
void __iomem *mregs = musb->mregs;
u8 devctl = musb_readb(mregs, MUSB_DEVCTL);
int err;
err = musb->int_usb & MUSB_INTR_VBUSERROR;
if (err) {
/*
* The Mentor core doesn't debounce VBUS as needed
* to cope with device connect current spikes. This
* means it's not uncommon for bus-powered devices
* to get VBUS errors during enumeration.
*
* This is a workaround, but newer RTL from Mentor
* seems to allow a better one: "re"-starting sessions
* without waiting for VBUS to stop registering in
* devctl.
*/
musb->int_usb &= ~MUSB_INTR_VBUSERROR;
musb->xceiv->state = OTG_STATE_A_WAIT_VFALL;
mod_timer(&otg_workaround, jiffies + POLL_SECONDS * HZ);
WARNING("VBUS error workaround (delay coming)\n");
} else if (drvvbus) {
MUSB_HST_MODE(musb);
otg->default_a = 1;
musb->xceiv->state = OTG_STATE_A_WAIT_VRISE;
portstate(musb->port1_status |= USB_PORT_STAT_POWER);
del_timer(&otg_workaround);
} else {
musb->is_active = 0;
MUSB_DEV_MODE(musb);
otg->default_a = 0;
musb->xceiv->state = OTG_STATE_B_IDLE;
portstate(musb->port1_status &= ~USB_PORT_STAT_POWER);
}
/* NOTE: this must complete power-on within 100 ms. */
dev_dbg(musb->controller, "VBUS %s (%s)%s, devctl %02x\n",
drvvbus ? "on" : "off",
usb_otg_state_string(musb->xceiv->state),
err ? " ERROR" : "",
devctl);
ret = IRQ_HANDLED;
}
/* Drop spurious RX and TX if device is disconnected */
if (musb->int_usb & MUSB_INTR_DISCONNECT) {
musb->int_tx = 0;
musb->int_rx = 0;
}
if (musb->int_tx || musb->int_rx || musb->int_usb)
ret |= musb_interrupt(musb);
eoi:
/* EOI needs to be written for the IRQ to be re-asserted. */
if (ret == IRQ_HANDLED || epintr || usbintr) {
/* clear level interrupt */
if (data->clear_irq)
data->clear_irq();
/* write EOI */
musb_writel(reg_base, USB_END_OF_INTR_REG, 0);
}
/* Poll for ID change */
if (musb->xceiv->state == OTG_STATE_B_IDLE)
mod_timer(&otg_workaround, jiffies + POLL_SECONDS * HZ);
spin_unlock_irqrestore(&musb->lock, flags);
return ret;
}
static irqreturn_t davinci_musb_interrupt(int irq, void *__hci)
{
unsigned long flags;
irqreturn_t retval = IRQ_NONE;
struct musb *musb = __hci;
struct usb_otg *otg = musb->xceiv->otg;
void __iomem *tibase = musb->ctrl_base;
struct cppi *cppi;
u32 tmp;
spin_lock_irqsave(&musb->lock, flags);
cppi = container_of(musb->dma_controller, struct cppi, controller);
if (is_cppi_enabled() && musb->dma_controller && !cppi->irq)
retval = cppi_interrupt(irq, __hci);
tmp = musb_readl(tibase, DAVINCI_USB_INT_SRC_MASKED_REG);
musb_writel(tibase, DAVINCI_USB_INT_SRC_CLR_REG, tmp);
dev_dbg(musb->controller, "IRQ %08x\n", tmp);
musb->int_rx = (tmp & DAVINCI_USB_RXINT_MASK)
>> DAVINCI_USB_RXINT_SHIFT;
musb->int_tx = (tmp & DAVINCI_USB_TXINT_MASK)
>> DAVINCI_USB_TXINT_SHIFT;
musb->int_usb = (tmp & DAVINCI_USB_USBINT_MASK)
>> DAVINCI_USB_USBINT_SHIFT;
if (tmp & (DAVINCI_INTR_DRVVBUS << DAVINCI_USB_USBINT_SHIFT)) {
int drvvbus = musb_readl(tibase, DAVINCI_USB_STAT_REG);
void __iomem *mregs = musb->mregs;
u8 devctl = musb_readb(mregs, MUSB_DEVCTL);
int err = musb->int_usb & MUSB_INTR_VBUSERROR;
err = is_host_enabled(musb)
&& (musb->int_usb & MUSB_INTR_VBUSERROR);
if (err) {
musb->int_usb &= ~MUSB_INTR_VBUSERROR;
musb->xceiv->state = OTG_STATE_A_WAIT_VFALL;
mod_timer(&otg_workaround, jiffies + POLL_SECONDS * HZ);
WARNING("VBUS error workaround (delay coming)\n");
} else if (is_host_enabled(musb) && drvvbus) {
MUSB_HST_MODE(musb);
otg->default_a = 1;
musb->xceiv->state = OTG_STATE_A_WAIT_VRISE;
portstate(musb->port1_status |= USB_PORT_STAT_POWER);
del_timer(&otg_workaround);
} else {
musb->is_active = 0;
MUSB_DEV_MODE(musb);
otg->default_a = 0;
musb->xceiv->state = OTG_STATE_B_IDLE;
portstate(musb->port1_status &= ~USB_PORT_STAT_POWER);
}
davinci_musb_source_power(musb, drvvbus, 0);
dev_dbg(musb->controller, "VBUS %s (%s)%s, devctl %02x\n",
drvvbus ? "on" : "off",
otg_state_string(musb->xceiv->state),
err ? " ERROR" : "",
devctl);
retval = IRQ_HANDLED;
}
if (musb->int_tx || musb->int_rx || musb->int_usb)
retval |= musb_interrupt(musb);
/* irq stays asserted until EOI is written */
musb_writel(tibase, DAVINCI_USB_EOI_REG, 0);
if (is_otg_enabled(musb)
&& musb->xceiv->state == OTG_STATE_B_IDLE)
mod_timer(&otg_workaround, jiffies + POLL_SECONDS * HZ);
spin_unlock_irqrestore(&musb->lock, flags);
return retval;
}
static irqreturn_t davinci_interrupt(int irq, void *__hci, struct pt_regs *r)
{
unsigned long flags;
irqreturn_t retval = IRQ_NONE;
struct musb *musb = __hci;
void *__iomem tibase = musb->ctrl_base;
u32 tmp;
spin_lock_irqsave(&musb->Lock, flags);
#ifdef CONFIG_USB_TI_CPPI_DMA
/* CPPI interrupts share the same IRQ line, but have their own
* mask, state, and EIO registers.
*/
{
u32 cppi_tx = musb_readl(tibase, DAVINCI_TXCPPI_MASKED_REG);
u32 cppi_rx = musb_readl(tibase, DAVINCI_RXCPPI_MASKED_REG);
if (cppi_tx || cppi_rx) {
DBG(4, "<== CPPI IRQ t%x r%x\n", cppi_tx, cppi_rx);
cppi_completion(musb, cppi_rx, cppi_tx);
retval = IRQ_HANDLED;
}
}
#endif
/* NOTE: DaVinci shadows the Mentor IRQs; don't manage them through
* the mentor registers (except for setup), use the TI ones and EOI.
*/
/* ack and handle non-CPPI interrupts */
tmp = musb_readl(tibase, DAVINCI_USB_INT_SRC_MASKED_REG);
musb_writel(tibase, DAVINCI_USB_INT_SRC_CLR_REG, tmp);
musb->int_rx = (tmp & DAVINCI_USB_RXINT_MASK)
>> DAVINCI_USB_RXINT_SHIFT;
musb->int_tx = (tmp & DAVINCI_USB_TXINT_MASK)
>> DAVINCI_USB_TXINT_SHIFT;
musb->int_usb = (tmp & DAVINCI_USB_USBINT_MASK)
>> DAVINCI_USB_USBINT_SHIFT;
musb->int_regs = r;
if (tmp & (1 << (8 + DAVINCI_USB_USBINT_SHIFT))) {
int drvvbus = musb_readl(tibase, DAVINCI_USB_STAT_REG);
/* NOTE: this must complete poweron within 100 msec */
DBG(1, "drvvbus Interrupt\n");
#ifndef CONFIG_ARCH_DAVINCI_DM355
#ifdef CONFIG_USB_MUSB_OTG
davinci_vbus_power(musb, drvvbus);
#elif defined(CONFIG_USB_MUSB_HDRC_HCD)
/* In host mode manipulate vbus based on core request
* but keep the session on.
*/
davinci_vbus_power(musb, drvvbus);
#endif
#endif
drvvbus = 0;
retval = IRQ_HANDLED;
}
if (musb->int_tx || musb->int_rx || musb->int_usb)
retval |= musb_interrupt(musb);
/* irq stays asserted until EOI is written */
musb_writel(tibase, DAVINCI_USB_EOI_REG, 0);
spin_unlock_irqrestore(&musb->Lock, flags);
/* REVISIT we sometimes get unhandled IRQs with CPPI
* (minimally, host TX). not clear why...
*/
if (retval != IRQ_HANDLED)
DBG(5, "unhandled? %08x\n", tmp);
return IRQ_HANDLED;
}
