/*******************************************************************************
* mvPciLocalBusNumSet - Set PCI interface local bus number.
*
* DESCRIPTION:
* This function sets given PCI interface its local bus number.
* Note: In case the PCI interface is PCI-X, the information is read-only.
*
* INPUT:
* pciIf - PCI interface number.
* busNum - Bus number.
*
* OUTPUT:
* None.
*
* RETURN:
* MV_NOT_ALLOWED in case PCI interface is PCI-X.
* MV_BAD_PARAM on bad parameters ,
* otherwise MV_OK
*
*******************************************************************************/
MV_STATUS mvPciIfLocalBusNumSet(MV_U32 pciIf, MV_U32 busNum)
{
PCI_IF_TYPE pciIfType = mvPciIfTypeGet(pciIf);
if (PCI_IF_TYPE_CONVEN_PCIX == pciIfType)
{
#if defined(MV_INCLUDE_PCI)
return mvPciLocalBusNumSet(pciIf - MV_PCI_START_IF,
busNum);
#else
return MV_OK;
#endif
}
else if (PCI_IF_TYPE_PEX == pciIfType)
{
#if defined(MV_INCLUDE_PEX)
return mvPexLocalBusNumSet(pciIf - MV_PEX_START_IF,
busNum);
#else
return MV_OK;
#endif
}
else
{
mvOsPrintf("%s: ERROR!!! Invalid pciIf %d\n", __FUNCTION__, pciIf);
}
return MV_FAIL;
}
MV_STATUS mvPexInit(MV_U32 pexIf, MV_PEX_TYPE pexType, MV_PEX_HAL_DATA *halData)
{
MV_PEX_MODE pexMode;
MV_U32 regVal;
MV_U32 status;
mvOsMemcpy(&pexHalData[pexIf], halData, sizeof(MV_PEX_HAL_DATA));
if (mvPexModeGet(pexIf, &pexMode) != MV_OK) {
mvOsPrintf("PEX init ERR. mvPexModeGet failed (pexType=%d)\n", pexMode.pexType);
return MV_ERROR;
}
if (pexMode.pexLinkUp == MV_FALSE) {
/* interface detected no Link. */
return MV_NO_SUCH;
}
/* Check that required PEX type is the one set in reset time */
if (pexType != pexMode.pexType) {
/* No Link. Shut down the Phy */
mvPexPhyPowerDown(pexIf);
mvOsPrintf("PEX init ERR. PEX type sampled mismatch (%d,%d)\n", pexType, pexMode.pexType);
return MV_ERROR;
}
if (MV_PEX_ROOT_COMPLEX == pexType) {
mvPexLocalBusNumSet(pexIf, PEX_HOST_BUS_NUM(pexIf));
mvPexLocalDevNumSet(pexIf, PEX_HOST_DEV_NUM(pexIf));
/* Local device master Enable */
mvPexMasterEnable(pexIf, MV_TRUE);
/* Local device slave Enable */
mvPexSlaveEnable(pexIf, mvPexLocalBusNumGet(pexIf), mvPexLocalDevNumGet(pexIf), MV_TRUE);
/* Interrupt disable */
status = MV_REG_READ(PEX_CFG_DIRECT_ACCESS(pexIf, PEX_STATUS_AND_COMMAND));
status |= PXSAC_INT_DIS;
MV_REG_WRITE(PEX_CFG_DIRECT_ACCESS(pexIf, PEX_STATUS_AND_COMMAND), status);
} else {
regVal = MV_REG_READ(PEX_DBG_CTRL_REG(pexIf));
regVal &= ~(BIT16 | BIT19);
MV_REG_WRITE(PEX_DBG_CTRL_REG(pexIf), regVal);
}
return MV_OK;
}
MV_STATUS mvPexHalInit(MV_U32 pexIf, MV_PEX_TYPE pexType)
{
MV_PEX_MODE pexMode;
MV_U32 regVal;
MV_U32 status;
/* First implement Guideline (GL# PCI Express-2) Wrong Default Value */
/* to Transmitter Output Current (TXAMP) Relevant for: 88F5181-A1/B0/B1 */
/* and 88F5281-B0 and above, 88F5182, 88F5082, 88F5181L, 88F6082/L */
if ((mvCtrlModelGet() != MV_1281_DEV_ID) &&
(mvCtrlModelGet() != MV_6281_DEV_ID) &&
(mvCtrlModelGet() != MV_6192_DEV_ID) &&
(mvCtrlModelGet() != MV_6190_DEV_ID) &&
(mvCtrlModelGet() != MV_6180_DEV_ID) &&
(mvCtrlModelGet() != MV_6183_DEV_ID) &&
(mvCtrlModelGet() != MV_6183L_DEV_ID) &&
(mvCtrlModelGet() != MV_78100_DEV_ID) &&
(mvCtrlModelGet() != MV_78200_DEV_ID) &&
(mvCtrlModelGet() != MV_76100_DEV_ID) &&
(mvCtrlModelGet() != MV_78XX0_DEV_ID))
{
/* Read current value of TXAMP */
MV_REG_WRITE(0x41b00, 0x80820000); /* Write the read command */
regVal = MV_REG_READ(0x41b00); /* Extract the data */
/* Prepare new data for write */
regVal &= ~0x7; /* Clear bits [2:0] */
regVal |= 0x4; /* Set the new value */
regVal &= ~0x80000000; /* Set "write" command */
MV_REG_WRITE(0x41b00, regVal); /* Write the write command */
}
else
{
/* Implement 1.0V termination GL for 88F1281 device only */
/* BIT0 - Common mode feedback */
/* BIT3 - TxBuf, extra drive for 1.0V termination */
if (mvCtrlModelGet() == MV_1281_DEV_ID)
{
MV_REG_WRITE(0x41b00, 0x80860000); /* Write the read command */
regVal = MV_REG_READ(0x41b00); /* Extract the data */
regVal |= (BIT0 | BIT3);
regVal &= ~0x80000000; /* Set "write" command */
MV_REG_WRITE(0x41b00, regVal); /* Write the write command */
MV_REG_WRITE(0x31b00, 0x80860000); /* Write the read command */
regVal = MV_REG_READ(0x31b00); /* Extract the data */
regVal |= (BIT0 | BIT3);
regVal &= ~0x80000000; /* Set "write" command */
MV_REG_WRITE(0x31b00, regVal); /* Write the write command */
}
}
if( mvPexModeGet(pexIf, &pexMode) != MV_OK)
{
mvOsPrintf("PEX init ERR. mvPexModeGet failed (pexType=%d)\n",pexMode.pexType);
return MV_ERROR;
}
/* Check that required PEX type is the one set in reset time */
if (pexType != pexMode.pexType)
{
/* No Link. Shut down the Phy */
mvPexPowerDown(pexIf);
mvOsPrintf("PEX init ERR. PEX type sampled mismatch (%d,%d)\n",pexType,pexMode.pexType);
return MV_ERROR;
}
if (MV_PEX_ROOT_COMPLEX == pexType)
{
mvPexLocalBusNumSet(pexIf, PEX_HOST_BUS_NUM(pexIf));
mvPexLocalDevNumSet(pexIf, PEX_HOST_DEV_NUM(pexIf));
/* Local device master Enable */
mvPexMasterEnable(pexIf, MV_TRUE);
/* Local device slave Enable */
mvPexSlaveEnable(pexIf, mvPexLocalBusNumGet(pexIf),
mvPexLocalDevNumGet(pexIf), MV_TRUE);
/* Interrupt disable */
status = MV_REG_READ(PEX_CFG_DIRECT_ACCESS(pexIf, PEX_STATUS_AND_COMMAND));
status |= PXSAC_INT_DIS;
MV_REG_WRITE(PEX_CFG_DIRECT_ACCESS(pexIf, PEX_STATUS_AND_COMMAND), status);
}
/* now wait 500 ms to be sure the link is valid (spec compliant) */
mvOsDelay(500);
/* Check if we have link */
if (MV_REG_READ(PEX_STATUS_REG(pexIf)) & PXSR_DL_DOWN)
{
mvOsPrintf("PEX%d interface detected no Link.\n",pexIf);
return MV_NO_SUCH;
}
if (MV_PEX_WITDH_X1 == pexMode.pexWidth)
{
mvOsPrintf("PEX%d interface detected Link X1\n",pexIf);
}
else
{
mvOsPrintf("PEX%d interface detected Link X4\n",pexIf);
}
#ifdef PCIE_VIRTUAL_BRIDGE_SUPPORT
mvPexVrtBrgInit(pexIf);
#endif
return MV_OK;
}
/*******************************************************************************
* mvCtrlHighSpeedSerdesPhyConfig
*
* DESCRIPTION: This is the main function which configure the
* PU sequence of the ser-des
*
* INPUT:
* None.
*
* OUTPUT:
* None.
*
* RETURN:
* MV_OK - success
* MV_ERROR - failure
*******************************************************************************/
MV_STATUS mvCtrlHighSpeedSerdesPhyConfig(MV_VOID)
{
MV_U32 serdesLaneNum, pexUnit;
MV_U32 uiReg;
MV_BIN_SERDES_UNIT_INDX serdesLaneCfg;
MV_U32 regAddr[16][11], regVal[16][11]; /* addr/value for each line @ every setup step */
MV_U8 maxSerdesLanes;
MV_U32 tmp;
MV_U32 tempReg, tempPexReg;
MV_U32 pexIf=0;
MV_U32 first_busno, next_busno;
MV_U32 addr;
MV_TWSI_ADDR slave;
MV_U32 boardId = mvBoardIdIndexGet(mvBoardIdGet());
maxSerdesLanes = mvCtrlSerdesMaxLanesGet();
if (maxSerdesLanes == 0)
return MV_OK;
/*Set MPP1 for twsi access */
uiReg = (MV_REG_READ(MPP_CONTROL_REG(1)) & 0x00FFFFFF) | 0x22000000;
MV_REG_WRITE(MPP_CONTROL_REG(1), uiReg);
/* TWSI init */
slave.type = ADDR7_BIT;
slave.address = 0;
mvTwsiInit(0, TWSI_SPEED, mvBoardTclkGet(), &slave, 0);
mvUartInit();
/* update board configuration (serdes lane topology and speed), if needed */
mvBoardUpdateBoardTopologyConfig(boardId);
/* Initialize board configuration database */
boardLaneConfig[0] = SERDES_UNIT_PEX; /* SerDes 0 is alwyas PCIe0*/
boardLaneConfig[1] = boardTopologyConfig[boardId].serdesTopology.lane1;
boardLaneConfig[2] = boardTopologyConfig[boardId].serdesTopology.lane2;
boardLaneConfig[3] = boardTopologyConfig[boardId].serdesTopology.lane3;
memset(regAddr, 0, sizeof(regAddr));
memset(regVal, 0, sizeof(regVal));
/* Check if DRAM is already initialized */
if (MV_REG_READ(REG_BOOTROM_ROUTINE_ADDR) & (1 << REG_BOOTROM_ROUTINE_DRAM_INIT_OFFS)) {
DEBUG_INIT_S("High speed PHY - Version: ");
DEBUG_INIT_S(SERDES_VERION);
DEBUG_INIT_S(" - 2nd boot - Skip \n");
return MV_OK;
}
DEBUG_INIT_S("High speed PHY - Version: ");
DEBUG_INIT_S(SERDES_VERION);
DEBUG_INIT_S(" (COM-PHY-V20) \n");
DEBUG_INIT_FULL_C("SERDES 0=",boardLaneConfig[0],2);
DEBUG_INIT_FULL_C("SERDES 1=",boardLaneConfig[1],2);
DEBUG_INIT_FULL_C("SERDES 2=",boardLaneConfig[2],2);
DEBUG_INIT_FULL_C("SERDES 3=",boardLaneConfig[3],2);
/*------------------------------------------*/
/* STEP - 1.5 Power Down PLL, RX, TX all phys */
/*------------------------------------------*/
for (serdesLaneNum = 0; serdesLaneNum < maxSerdesLanes; serdesLaneNum++)
{
uiReg=MV_REG_READ(COMMON_PHY_CONFIGURATION1_REG(serdesLaneNum));
uiReg &= ~PIN_TX_IDLE_MASK;
uiReg &= ~(PHY_POWER_UP_PLL_MASK | PHY_POWER_UP_RX_MASK | PHY_POWER_UP_TX_MASK);
MV_REG_WRITE(COMMON_PHY_CONFIGURATION1_REG(serdesLaneNum),uiReg);
}
mvOsUDelay(10000);
/*--------------------------------------------------------*/
/* STEP - 2 Reset PHY and PIPE (Zx: Un-reset, Ax: Reset)*/
/*--------------------------------------------------------*/
for (serdesLaneNum = 0; serdesLaneNum < maxSerdesLanes; serdesLaneNum++)
{
#ifndef CONFIG_ALP_A375_ZX_REV
resetPhyAndPipe(serdesLaneNum, MV_TRUE);
#else
resetPhyAndPipe(serdesLaneNum, MV_FALSE);
#endif
}
/*--------------------------------*/
/* STEP - 2 Common PHYs Selectors */
/*--------------------------------*/
MV_REG_WRITE(COMMON_PHY_SELECTOR_REG, GetLaneSelectorConfig());
/*--------------------------------*/
/* STEP - 3 Configuration 1 */
/*--------------------------------*/
for (serdesLaneNum = 0; serdesLaneNum < maxSerdesLanes; serdesLaneNum++) {
serdesLaneCfg = mvGetSerdesLaneCfg(serdesLaneNum);
if(serdesLaneCfg >= SERDES_LAST_UNIT){
return MV_ERROR;
}
uiReg = MV_REG_READ(COMMON_PHY_CONFIGURATION1_REG(serdesLaneNum));
switch(serdesLaneCfg){
case SERDES_UNIT_USB3:
#ifndef CONFIG_ALP_A375_ZX_REV
A375_A0_COMMON_PHY_CONFIG(uiReg);
#endif
uiReg |= PHY_MODE_MASK; /* PHY Mode = USB */
uiReg |= PIPE_SELECT_MASK ; /* Select USB3_PEX */
break;
case SERDES_UNIT_PEX:
uiReg |= PIPE_SELECT_MASK ; /* Select USB3_PEX */
#ifndef CONFIG_ALP_A375_ZX_REV
uiReg &= ~(PHY_MODE_MASK); /* PHY Mode = PEX */
A375_A0_COMMON_PHY_CONFIG(uiReg);
#endif
break;
case SERDES_UNIT_SGMII:
case SERDES_UNIT_SATA:
#ifndef CONFIG_ALP_A375_ZX_REV
A375_A0_COMMON_PHY_CONFIG(uiReg);
#endif
uiReg &= ~(PIPE_SELECT_MASK); /* Select SATA_SGMII */
uiReg |= POWER_UP_IVREF_MASK; /* Power UP IVREF = Power Up */
break;
case SERDES_UNIT_UNCONNECTED:
default:
break;
}
/* Serdes speed config */
tmp = getSerdesSpeedConfig(boardId, serdesLaneCfg);
uiReg &= ~(GEN_RX_MASK); /* SERDES RX Speed config */
uiReg |= tmp<<GEN_RX_OFFS;
uiReg &= ~(GEN_TX_MASK); /* SERDES TX Speed config */
uiReg |= tmp<<GEN_TX_OFFS;
MV_REG_WRITE(COMMON_PHY_CONFIGURATION1_REG(serdesLaneNum),uiReg);
}
#ifndef CONFIG_ALP_A375_ZX_REV
/*------------------------------------------*/
/* STEP - 3.5 Unreset PHY and PIPE(only Ax)*/
/*------------------------------------------*/
for (serdesLaneNum = 0; serdesLaneNum < maxSerdesLanes; serdesLaneNum++) {
resetPhyAndPipe(serdesLaneNum, MV_FALSE);
}
#endif
/*----------------------------------------*/
/* STEP - 4 COMPHY register configuration */
/*----------------------------------------*/
for (serdesLaneNum = 0; serdesLaneNum < maxSerdesLanes; serdesLaneNum++) {
serdesLaneCfg = mvGetSerdesLaneCfg(serdesLaneNum);
if(serdesLaneCfg >= SERDES_LAST_UNIT){
return MV_ERROR;
}
switch(serdesLaneCfg){
case SERDES_UNIT_PEX:
MV_REG_WRITE(RESET_AND_CLOCK_CONTROL_REG(serdesLaneNum),0x25); /* Enable soft_reset*/
MV_REG_WRITE(POWER_AND_PLL_CONTROL_REG(serdesLaneNum),0xFC60); /* PHY Mode = PEX */
#ifndef CONFIG_ALP_A375_ZX_REV
MV_REG_WRITE(MISCELLANEOUS_CONTROL0_REG(serdesLaneNum),0x6017); /* REFCLK SEL =0x0 (100Mhz) */
MV_REG_WRITE(INTERFACE_REG1_REG(serdesLaneNum),0x1400); /* PHY_Gen_Max = 5G */
MV_REG_WRITE(DIGITAL_LOOPBACK_ENABLE_REG(serdesLaneNum),0x400); /* SEL_Bits = 20-Bit */
A375_A0_RESET_DFE_SEQUENCE(serdesLaneNum);
#else
MV_REG_WRITE(KVCO_CALOBRATION_CONTROL_REG(serdesLaneNum),0x40); /* use_max_pll_rate=0x0, ext_force_cal_done=0x0 */
#endif
MV_REG_WRITE(RESET_AND_CLOCK_CONTROL_REG(serdesLaneNum),0x24); /* Release soft_reset */
break;
case SERDES_UNIT_USB3:
MV_REG_WRITE(RESET_AND_CLOCK_CONTROL_REG(serdesLaneNum),0x21); /* Enable soft_reset*/
MV_REG_WRITE(POWER_AND_PLL_CONTROL_REG(serdesLaneNum),0xFCA0); /* PHY Mode = USB3 */
#ifndef CONFIG_ALP_A375_ZX_REV
MV_REG_WRITE(LANE_CONFIGURATION_4_REG(serdesLaneNum),0x13); /* Ref_Clk =100Mhz */
MV_REG_WRITE(MISCELLANEOUS_CONTROL0_REG(serdesLaneNum),0x6017); /* REFCLK SEL =0x0 (100Mhz) */
MV_REG_WRITE(INTERFACE_REG1_REG(serdesLaneNum),0x1400); /* PHY_Gen_Max = 5G */
MV_REG_WRITE(DIGITAL_LOOPBACK_ENABLE_REG(serdesLaneNum),0x400); /* SEL_Bits = 20-Bit */
A375_A0_RESET_DFE_SEQUENCE(serdesLaneNum);
#else
MV_REG_WRITE(KVCO_CALOBRATION_CONTROL_REG(serdesLaneNum),0x40); /* use_max_pll_rate=0x0, ext_force_cal_done=0x0 */
MV_REG_WRITE(GENERETION_2_SETTINGS_1_REG(serdesLaneNum),0x149); /* Mulitiple frequency setup */
#endif
MV_REG_WRITE(RESET_AND_CLOCK_CONTROL_REG(serdesLaneNum),0x20); /* Release soft_reset */
break;
case SERDES_UNIT_SATA:
MV_REG_WRITE(POWER_AND_PLL_CONTROL_REG(serdesLaneNum),0xFC01); /* PHY Mode = SATA */
MV_REG_WRITE(MISCELLANEOUS_CONTROL0_REG(serdesLaneNum),0x6417); /* REFCLK SEL =0x1 (25Mhz) */
#ifndef CONFIG_ALP_A375_ZX_REV
MV_REG_WRITE(INTERFACE_REG1_REG(serdesLaneNum),0x1400); /* PHY_Gen_Max = 5G */
MV_REG_WRITE(DIGITAL_LOOPBACK_ENABLE_REG(serdesLaneNum),0x400); /* SEL_Bits = 20-Bit */
MV_REG_WRITE(DIGITAL_RESERVED0_REG(serdesLaneNum),0xE); /* Reg_sq_de_glitch_en */
A375_A0_RESET_DFE_SEQUENCE(serdesLaneNum);
#else
MV_REG_WRITE(RESERVED_46_REG(serdesLaneNum),0xFF00);
#endif
break;
case SERDES_UNIT_SGMII:
MV_REG_WRITE(POWER_AND_PLL_CONTROL_REG(serdesLaneNum),0xFC81); /* PHY Mode = SGMII */ /*moti need to change offset*/
MV_REG_WRITE(DIGITAL_LOOPBACK_ENABLE_REG(serdesLaneNum),0x0); /* SEL_BITS = 0x0 (10-bits mode) */
MV_REG_WRITE(MISCELLANEOUS_CONTROL0_REG(serdesLaneNum),0x6417); /* REFCLK SEL =0x1 (25Mhz) */
#ifndef CONFIG_ALP_A375_ZX_REV
MV_REG_WRITE(DIGITAL_RESERVED0_REG(serdesLaneNum),0xE); /* Reg_sq_de_glitch_en */
A375_A0_RESET_DFE_SEQUENCE(serdesLaneNum);
#else
MV_REG_WRITE(RESERVED_46_REG(serdesLaneNum),0xFF00); /* Enable soft_reset*/
#endif
MV_REG_WRITE(PHY_ISOLATION_MODE_CONTROL_REG(serdesLaneNum),0x166); /* Set PHY_GEN_TX/RX to 1.25Gbps */
break;
case SERDES_UNIT_UNCONNECTED:
default:
break;
}
}
/*------------------------------------------*/
/* STEP - 4.5 Power up PLL, RX, TX all phys */
/*------------------------------------------*/
for (serdesLaneNum = 0; serdesLaneNum < maxSerdesLanes; serdesLaneNum++)
{
uiReg=MV_REG_READ(COMMON_PHY_CONFIGURATION1_REG(serdesLaneNum));
uiReg |= (PHY_POWER_UP_PLL_MASK | PHY_POWER_UP_RX_MASK | PHY_POWER_UP_TX_MASK);
MV_REG_WRITE(COMMON_PHY_CONFIGURATION1_REG(serdesLaneNum),uiReg);
}
#ifndef CONFIG_ALP_A375_ZX_REV
mvOsUDelay(5000);
/*--------------------------------------------------------------------*/
/* STEP - 4.6 (Only SGMII/SATA): WAIT for PHY Power up sequence to finish */
/*--------------------------------------------------------------------*/
for (serdesLaneNum = 0; serdesLaneNum < maxSerdesLanes; serdesLaneNum++) {
serdesLaneCfg = mvGetSerdesLaneCfg(serdesLaneNum);
if(serdesLaneCfg >= SERDES_LAST_UNIT){
return MV_ERROR;
}
switch(serdesLaneCfg){
case SERDES_UNIT_SATA:
case SERDES_UNIT_SGMII:
uiReg = MV_REG_READ(COMMON_PHY_STATUS1_REG(serdesLaneNum));
if ((uiReg & 0x6) != 0x6) {
DEBUG_INIT_S("Phy Power up did't finished\n");
return MV_ERROR;
}
case SERDES_UNIT_UNCONNECTED:
default:
break;
}
}
#endif
/*----------------------------------------*/
/* STEP - 5 PEX Only */
/*----------------------------------------*/
for (pexUnit = 0; pexUnit < 4; pexUnit++) {
if (boardLaneConfig[pexUnit] != SERDES_UNIT_PEX)
continue;
tmp = MV_REG_READ(PEX_CAPABILITIES_REG(pexUnit));
DEBUG_RD_REG(PEX_CAPABILITIES_REG(pexUnit), tmp );
tmp &= ~(0xf<<20);
tmp |= (0x4<<20);
MV_REG_WRITE(PEX_CAPABILITIES_REG(pexUnit),tmp);
DEBUG_WR_REG(PEX_CAPABILITIES_REG(pexUnit),tmp);
}
tmp = MV_REG_READ(SOC_CTRL_REG);
DEBUG_RD_REG(SOC_CTRL_REG, tmp);
tmp &= ~(0x03);
tmp |= 0x1<<PCIE0_ENABLE_OFFS;
if (boardLaneConfig[1] == SERDES_UNIT_PEX)
tmp |= 0x1<<PCIE1_ENABLE_OFFS;
MV_REG_WRITE(SOC_CTRL_REG, tmp);
DEBUG_WR_REG(SOC_CTRL_REG, tmp);
/*----------------------------------------*/
/* STEP - 6 PEX Only - support gen1/gen2 */
/*----------------------------------------*/
next_busno = 0;
mvOsDelay(150);
for (pexIf = 0; pexIf < 2; pexIf++) // only pexIf 0 on
{
if (boardLaneConfig[pexIf] != SERDES_UNIT_PEX)
continue;
tmp = MV_REG_READ(PEX_DBG_STATUS_REG(pexIf));
DEBUG_RD_REG(PEX_DBG_STATUS_REG(pexIf), tmp);
first_busno = next_busno;
if ((tmp & 0x7f) == 0x7E) {
next_busno++;
tempPexReg = MV_REG_READ((PEX_CFG_DIRECT_ACCESS(pexIf, PEX_LINK_CAPABILITY_REG)));
DEBUG_RD_REG((PEX_CFG_DIRECT_ACCESS(pexIf, PEX_LINK_CAPABILITY_REG)),tempPexReg );
tempPexReg &= (0xF);
if (tempPexReg == 0x2) {
tempReg = (MV_REG_READ(PEX_CFG_DIRECT_ACCESS(pexIf, PEX_LINK_CTRL_STAT_REG)) & 0xF0000) >> 16;
DEBUG_RD_REG(PEX_CFG_DIRECT_ACCESS(pexIf, PEX_LINK_CTRL_STAT_REG),tempReg );
/* check if the link established is GEN1 */
if (tempReg == 0x1) {
mvPexLocalBusNumSet(pexIf, first_busno);
mvPexLocalDevNumSet(pexIf, 1);
DEBUG_INIT_FULL_S("PEX: pexIf ");
DEBUG_INIT_FULL_D(pexIf, 1);
DEBUG_INIT_FULL_S(", link is Gen1, checking the EP capability \n");
/* link is Gen1, check the EP capability */
addr = mvPexConfigRead(pexIf, first_busno, 0, 0, 0x34) & 0xFF;
DEBUG_INIT_FULL_C("mvPexConfigRead: return addr=0x%x", addr,4);
if (addr == 0xff) {
DEBUG_INIT_FULL_C("mvPexConfigRead: return 0xff -->PEX (%d): Detected No Link.", pexIf,1);
continue;
}
while ((mvPexConfigRead(pexIf, first_busno, 0, 0, addr) & 0xFF) != 0x10) {
addr = (mvPexConfigRead(pexIf, first_busno, 0, 0, addr) & 0xFF00) >> 8;
}
if ((mvPexConfigRead(pexIf, first_busno, 0, 0, addr + 0xC) & 0xF) >= 0x2) {
tmp = MV_REG_READ(PEX_LINK_CTRL_STATUS2_REG(pexIf));
DEBUG_RD_REG(PEX_LINK_CTRL_STATUS2_REG(pexIf),tmp );
tmp &=~(BIT0 | BIT1);
tmp |= BIT1;
MV_REG_WRITE(PEX_LINK_CTRL_STATUS2_REG(pexIf),tmp);
DEBUG_WR_REG(PEX_LINK_CTRL_STATUS2_REG(pexIf),tmp);
tmp = MV_REG_READ(PEX_CTRL_REG(pexIf));
DEBUG_RD_REG(PEX_CTRL_REG(pexIf), tmp );
tmp |= BIT10;
MV_REG_WRITE(PEX_CTRL_REG(pexIf),tmp);
DEBUG_WR_REG(PEX_CTRL_REG(pexIf),tmp);
mvOsUDelay(10000);/* We need to wait 10ms before reading the PEX_DBG_STATUS_REG in order not to read the status of the former state*/
DEBUG_INIT_FULL_S("PEX: pexIf ");
DEBUG_INIT_FULL_D(pexIf, 1);
DEBUG_INIT_FULL_S(", Link upgraded to Gen2 based on client cpabilities \n");
} else {
DEBUG_INIT_FULL_S("PEX: pexIf ");
DEBUG_INIT_FULL_D(pexIf, 1);
DEBUG_INIT_FULL_S(", remains Gen1\n");
}
}
}
MV_STATUS mvPexInit(MV_U32 pexIf, MV_PEX_TYPE pexType, MV_PEX_HAL_DATA *halData)
{
MV_PEX_MODE pexMode;
MV_U32 regVal;
MV_U32 status;
MV_U16 ctrlModel, phyRegVal;
mvOsMemcpy(&pexHalData[pexIf], halData, sizeof(MV_PEX_HAL_DATA));
/* First implement Guideline (GL# PCI Express-2) Wrong Default Value */
/* to Transmitter Output Current (TXAMP) Relevant for: 88F5181-A1/B0/B1 */
/* and 88F5281-B0 and above, 88F5182, 88F5082, 88F5181L, 88F6082/L */
ctrlModel = pexHalData[pexIf].ctrlModel;
if ((ctrlModel != MV_1281_DEV_ID) &&
(ctrlModel != MV_6281_DEV_ID) &&
(ctrlModel != MV_6282_DEV_ID) &&
(ctrlModel != MV_6280_DEV_ID) &&
(ctrlModel != MV_6192_DEV_ID) &&
(ctrlModel != MV_6190_DEV_ID) &&
(ctrlModel != MV_6180_DEV_ID) &&
(ctrlModel != MV_6183_DEV_ID) &&
(ctrlModel != MV_6183L_DEV_ID) &&
(ctrlModel != MV_78100_DEV_ID) &&
(ctrlModel != MV_78200_DEV_ID) &&
(ctrlModel != MV_76100_DEV_ID) &&
(ctrlModel != MV_6323_DEV_ID) &&
(ctrlModel != MV_6322_DEV_ID) &&
(ctrlModel != MV_6321_DEV_ID) &&
(ctrlModel != MV_78XX0_DEV_ID) &&
(ctrlModel != MV_6510_DEV_ID) &&
(ctrlModel != MV_6530_DEV_ID) &&
(ctrlModel != MV_6550_DEV_ID) &&
(ctrlModel != MV_6560_DEV_ID) &&
(ctrlModel != MV_6710_DEV_ID) &&
(ctrlModel != MV_78130_DEV_ID) &&
(ctrlModel != MV_78160_DEV_ID) &&
(ctrlModel != MV_78230_DEV_ID) &&
(ctrlModel != MV_78260_DEV_ID) &&
(ctrlModel != MV_78460_DEV_ID) &&
(ctrlModel != MV_78000_DEV_ID)) {
/* Read current value of TXAMP */
MV_REG_WRITE(PEX_PHY_ACCESS_REG(pexIf), 0x80820000); /* Write the read command */
regVal = MV_REG_READ(PEX_PHY_ACCESS_REG(pexIf)); /* Extract the data */
/* Prepare new data for write */
regVal &= ~0x7; /* Clear bits [2:0] */
regVal |= 0x4; /* Set the new value */
regVal &= ~0x80000000; /* Set "write" command */
MV_REG_WRITE(PEX_PHY_ACCESS_REG(pexIf), regVal); /* Write the write command */
} else {
/* Implement 1.0V termination GL for 88F1281 device only */
/* BIT0 - Common mode feedback */
/* BIT3 - TxBuf, extra drive for 1.0V termination */
if (ctrlModel == MV_1281_DEV_ID) {
MV_REG_WRITE(PEX_PHY_ACCESS_REG(pexIf), 0x80860000); /* Write the read command */
regVal = MV_REG_READ(0x41b00); /* Extract the data */
regVal |= (BIT0 | BIT3);
regVal &= ~0x80000000; /* Set "write" command */
MV_REG_WRITE(PEX_PHY_ACCESS_REG(pexIf), regVal); /* Write the write command */
MV_REG_WRITE(0x31b00, 0x80860000); /* Write the read command */
regVal = MV_REG_READ(0x31b00); /* Extract the data */
regVal |= (BIT0 | BIT3);
regVal &= ~0x80000000; /* Set "write" command */
MV_REG_WRITE(0x31b00, regVal); /* Write the write command */
}
}
if ((ctrlModel == MV_6281_DEV_ID) ||
(ctrlModel == MV_6282_DEV_ID) ||
(ctrlModel == MV_6280_DEV_ID) ||
(ctrlModel == MV_6192_DEV_ID) ||
(ctrlModel == MV_6190_DEV_ID) ||
(ctrlModel == MV_6180_DEV_ID)) {
regVal = MV_REG_READ(0x100e4); /* This register currently doesn't appear in the FS */
regVal |= 0x3 << 25;
MV_REG_WRITE(0x100e4, regVal);
}
if (ctrlModel == MV_6282_DEV_ID) {
mvPexPhyRegRead(pexIf, 0x92, &phyRegVal);
phyRegVal &= ~(0x80F0);
phyRegVal |= 0x8080;
mvPexPhyRegWrite(pexIf, 0x92, phyRegVal);
} else if ((ctrlModel == MV_6510_DEV_ID) ||
(ctrlModel == MV_6530_DEV_ID) || (ctrlModel == MV_6550_DEV_ID) || (ctrlModel == MV_6560_DEV_ID)) {
regVal = MV_REG_READ(0x100e4); /* This register currently doesn't appear in the FS */
regVal |= 0x3 << 25;
MV_REG_WRITE(0x100e4, regVal);
mvPexPhyRegRead(pexIf, 0x92, &phyRegVal);
phyRegVal &= ~(0x80F0);
phyRegVal |= 0x8080;
mvPexPhyRegWrite(pexIf, 0x92, phyRegVal);
}
if (mvPexModeGet(pexIf, &pexMode) != MV_OK) {
mvOsPrintf("PEX init ERR. mvPexModeGet failed (pexType=%d)\n", pexMode.pexType);
return MV_ERROR;
}
/* Check that required PEX type is the one set in reset time */
if (pexType != pexMode.pexType) {
/* No Link. Shut down the Phy */
mvPexPhyPowerDown(pexIf);
mvOsPrintf("PEX init ERR. PEX type sampled mismatch (%d,%d)\n", pexType, pexMode.pexType);
return MV_ERROR;
}
if (MV_PEX_ROOT_COMPLEX == pexType) {
mvPexLocalBusNumSet(pexIf, PEX_HOST_BUS_NUM(pexIf));
mvPexLocalDevNumSet(pexIf, PEX_HOST_DEV_NUM(pexIf));
/* Local device master Enable */
mvPexMasterEnable(pexIf, MV_TRUE);
/* Local device slave Enable */
mvPexSlaveEnable(pexIf, mvPexLocalBusNumGet(pexIf), mvPexLocalDevNumGet(pexIf), MV_TRUE);
/* Interrupt disable */
status = MV_REG_READ(PEX_CFG_DIRECT_ACCESS(pexIf, PEX_STATUS_AND_COMMAND));
status |= PXSAC_INT_DIS;
MV_REG_WRITE(PEX_CFG_DIRECT_ACCESS(pexIf, PEX_STATUS_AND_COMMAND), status);
if (ctrlModel == MV_6710_DEV_ID) {
/* PEX capability */
regVal = MV_REG_READ(PEX_CFG_DIRECT_ACCESS(pexIf, PEX_LINK_CAPABILITY_REG)) & 0xF;
if (regVal == 0x2) {
/* KW40 set to Gen 2.0 - conf_auto_speed_change */
/* when bit is set, link will issue link speed change to the max link speed possible */
regVal = MV_REG_READ(PEX_CTRL_REG(pexIf)) | (1<<10);
MV_REG_WRITE(PEX_CTRL_REG(pexIf), regVal);
}
}
} else {
/* TODO: 14/12/10 - requested by CV to support EP Compliance */
MV_REG_WRITE(PEX_DBG_CTRL_REG(pexIf), 0x0F62F0C0);
MV_REG_WRITE(PEX_PHY_ACCESS_REG(pexIf), (0x80C2 << 16));
regVal = MV_REG_READ(PEX_PHY_ACCESS_REG(pexIf)) & 0xFFFF;
MV_REG_WRITE(PEX_PHY_ACCESS_REG(pexIf), (0xC2 << 16) | regVal | (1 << 2));
MV_REG_WRITE(PEX_PHY_ACCESS_REG(pexIf), (0x8080 << 16));
regVal = MV_REG_READ(PEX_PHY_ACCESS_REG(pexIf)) & 0xFFFF;
MV_REG_WRITE(PEX_PHY_ACCESS_REG(pexIf), (0x80 << 16) | regVal | (0x2 << 1));
}
mvSysPexCpuIfEnable(pexIf);
/* now wait 1ms to be sure the link is valid */
mvOsDelay(100);
/* Check if we have link */
if (MV_REG_READ(PEX_STATUS_REG(pexIf)) & PXSR_DL_DOWN) {
/*mvOsPrintf("PEX%d interface detected no Link.\n", pexIf);*/
return MV_NO_SUCH;
}
#if 0
if (MV_PEX_WITDH_X1 == pexMode.pexWidth)
mvOsPrintf("PEX%d interface detected Link X1\n", pexIf);
else
mvOsPrintf("PEX%d interface detected Link X4\n", pexIf);
#endif
#ifdef PCIE_VIRTUAL_BRIDGE_SUPPORT
mvPexVrtBrgInit(pexIf);
#endif
return MV_OK;
}
