static void __init beagle_opp_init(void)
{
int r = 0;
/* Initialize the omap3 opp table */
if (omap3_opp_init()) {
pr_err("%s: opp default init failed\n", __func__);
return;
}
/* Custom OPP enabled for XM */
if (omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XM || omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XMC) {
struct omap_hwmod *mh = omap_hwmod_lookup("mpu");
struct omap_hwmod *dh = omap_hwmod_lookup("iva");
struct device *dev;
if (!mh || !dh) {
pr_err("%s: Aiee.. no mpu/dsp devices? %p %p\n",
__func__, mh, dh);
r = -EINVAL;
} else {
/* Enable MPU 1GHz and lower opps */
dev = &mh->od->pdev.dev;
r = opp_enable(dev, 800000000);
r |= opp_enable(dev, 1000000000);
/* Enable IVA 800MHz and lower opps */
dev = &dh->od->pdev.dev;
r |= opp_enable(dev, 660000000);
r |= opp_enable(dev, 800000000);
}
if (r) {
pr_err("%s: failed to enable higher opp %d\n",
__func__, r);
/*
* Cleanup - disable the higher freqs - we dont care
* about the results
*/
dev = &mh->od->pdev.dev;
opp_disable(dev, 800000000);
opp_disable(dev, 1000000000);
dev = &dh->od->pdev.dev;
opp_disable(dev, 660000000);
opp_disable(dev, 800000000);
} else {
pr_err("%s: turbo OPPs enabled!\n", __func__);
}
}
}
static void __init beagle_display_init(void)
{
int r;
/* DVI reset GPIO is different between beagle revisions */
if ((omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XM) ||
(omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XMC))
beagle_dvi_device.reset_gpio = 129;
else
beagle_dvi_device.reset_gpio = 170;
r = gpio_request(beagle_dvi_device.reset_gpio, "DVI reset");
if (r < 0) {
printk(KERN_ERR "Unable to get DVI reset GPIO\n");
return;
}
gpio_direction_output(beagle_dvi_device.reset_gpio, 0);
}
static int beagle_twl_gpio_setup(struct device *dev,
unsigned gpio, unsigned ngpio)
{
if (omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XM) {
mmc[0].gpio_wp = -EINVAL;
} else if ((omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_C1_3) ||
(omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_C4)) {
omap_mux_init_gpio(23, OMAP_PIN_INPUT);
mmc[0].gpio_wp = 23;
} else {
omap_mux_init_gpio(29, OMAP_PIN_INPUT);
}
/* gpio + 0 is "mmc0_cd" (input/IRQ) */
mmc[0].gpio_cd = gpio + 0;
omap2_hsmmc_init(mmc);
/* link regulators to MMC adapters */
beagle_vmmc1_supply.dev = mmc[0].dev;
beagle_vsim_supply.dev = mmc[0].dev;
/* REVISIT: need ehci-omap hooks for external VBUS
* power switch and overcurrent detect
*/
gpio_request(gpio + 1, "EHCI_nOC");
gpio_direction_input(gpio + 1);
/* TWL4030_GPIO_MAX + 0 == ledA, EHCI nEN_USB_PWR (out, active low) */
gpio_request(gpio + TWL4030_GPIO_MAX, "nEN_USB_PWR");
gpio_direction_output(gpio + TWL4030_GPIO_MAX, 0);
/* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
return 0;
}
static int beagle_twl_gpio_setup(struct device *dev,
unsigned gpio, unsigned ngpio)
{
int r;
if ((omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XM) ||
(omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XMC)) {
mmc[0].gpio_wp = -EINVAL;
} else if ((omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_C1_3) ||
(omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_C4)) {
omap_mux_init_gpio(23, OMAP_PIN_INPUT);
mmc[0].gpio_wp = 23;
} else {
omap_mux_init_gpio(29, OMAP_PIN_INPUT);
}
/* gpio + 0 is "mmc0_cd" (input/IRQ) */
mmc[0].gpio_cd = gpio + 0;
omap2_hsmmc_init(mmc);
/* link regulators to MMC adapters */
beagle_vmmc1_supply.dev = mmc[0].dev;
beagle_vsim_supply.dev = mmc[0].dev;
/* REVISIT: need ehci-omap hooks for external VBUS
* power switch and overcurrent detect
*/
if ((omap3_beagle_get_rev() != OMAP3BEAGLE_BOARD_XM) &&
(omap3_beagle_get_rev() != OMAP3BEAGLE_BOARD_XMC)) {
r = gpio_request(gpio + 1, "EHCI_nOC");
if (!r) {
r = gpio_direction_input(gpio + 1);
if (r)
gpio_free(gpio + 1);
}
if (r)
pr_err("%s: unable to configure EHCI_nOC\n", __func__);
}
/*
* TWL4030_GPIO_MAX + 0 == ledA, EHCI nEN_USB_PWR (out, XM active
* high / others active low)
*/
gpio_request(gpio + TWL4030_GPIO_MAX, "nEN_USB_PWR");
if (omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XM)
gpio_direction_output(gpio + TWL4030_GPIO_MAX, 1);
else
gpio_direction_output(gpio + TWL4030_GPIO_MAX, 0);
/* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
/*
* gpio + 1 on Xm controls the TFP410's enable line (active low)
* gpio + 2 control varies depending on the board rev as follows:
* P7/P8 revisions(prototype): Camera EN
* A2+ revisions (production): LDO (supplies DVI, serial, led blocks)
*/
if ((omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XM) ||
(omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XMC)) {
r = gpio_request(gpio + 1, "nDVI_PWR_EN");
if (!r) {
r = gpio_direction_output(gpio + 1, 0);
if (r)
gpio_free(gpio + 1);
}
if (r)
pr_err("%s: unable to configure nDVI_PWR_EN\n",
__func__);
r = gpio_request(gpio + 2, "DVI_LDO_EN");
if (!r) {
r = gpio_direction_output(gpio + 2, 1);
if (r)
gpio_free(gpio + 2);
}
if (r)
pr_err("%s: unable to configure DVI_LDO_EN\n",
__func__);
}
return 0;
}
static int beagle_twl_gpio_setup(struct device *dev,
unsigned gpio, unsigned ngpio)
{
int r, usb_pwr_level;
if (omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XM) {
mmc[0].gpio_wp = -EINVAL;
} else if ((omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_C1_3) ||
(omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_C4)) {
omap_mux_init_gpio(23, OMAP_PIN_INPUT);
mmc[0].gpio_wp = 23;
} else {
omap_mux_init_gpio(29, OMAP_PIN_INPUT);
}
/* gpio + 0 is "mmc0_cd" (input/IRQ) */
mmc[0].gpio_cd = gpio + 0;
omap2_hsmmc_init(mmc);
/* link regulators to MMC adapters */
beagle_vmmc1_supply.dev = mmc[0].dev;
beagle_vsim_supply.dev = mmc[0].dev;
/*
* TWL4030_GPIO_MAX + 0 == ledA, EHCI nEN_USB_PWR (out, XM active
* high / others active low)
* DVI reset GPIO is different between beagle revisions
*/
if (omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XM) {
usb_pwr_level = GPIOF_OUT_INIT_HIGH;
beagle_dvi_device.reset_gpio = 129;
/*
* gpio + 1 on Xm controls the TFP410's enable line (active low)
* gpio + 2 control varies depending on the board rev as below:
* P7/P8 revisions(prototype): Camera EN
* A2+ revisions (production): LDO (DVI, serial, led blocks)
*/
r = gpio_request_one(gpio + 1, GPIOF_OUT_INIT_LOW,
"nDVI_PWR_EN");
if (r)
pr_err("%s: unable to configure nDVI_PWR_EN\n",
__func__);
r = gpio_request_one(gpio + 2, GPIOF_OUT_INIT_HIGH,
"DVI_LDO_EN");
if (r)
pr_err("%s: unable to configure DVI_LDO_EN\n",
__func__);
} else {
usb_pwr_level = GPIOF_OUT_INIT_LOW;
beagle_dvi_device.reset_gpio = 170;
/*
* REVISIT: need ehci-omap hooks for external VBUS
* power switch and overcurrent detect
*/
if (gpio_request_one(gpio + 1, GPIOF_IN, "EHCI_nOC"))
pr_err("%s: unable to configure EHCI_nOC\n", __func__);
}
gpio_request_one(gpio + TWL4030_GPIO_MAX, usb_pwr_level, "nEN_USB_PWR");
/* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
return 0;
}
