void sch4037_early_init(unsigned port)
{
pnp_devfn_t dev;
dev = PNP_DEV(port, SMSCSUPERIO_SP1);
pnp_enter_conf_state(dev);
/* Auto power management */
pnp_write_config(dev, 0x22, 0x38); /* BIT3+BIT4+BIT5 */
pnp_write_config(dev, 0x23, 0);
/* Enable SMSC UART 0 */
dev = PNP_DEV(port, SMSCSUPERIO_SP1);
pnp_set_logical_device(dev);
pnp_set_enable(dev, 0);
pnp_set_iobase(dev, PNP_IDX_IO0, CONFIG_TTYS0_BASE);
pnp_set_irq(dev, PNP_IDX_IRQ0, 0x4);
/* Enabled High speed, disabled MIDI support. */
pnp_write_config(dev, 0xF0, 0x02);
pnp_set_enable(dev, 1);
/* Enable keyboard */
dev = PNP_DEV(port, SCH4037_KBC);
pnp_set_logical_device(dev);
pnp_set_enable(dev, 0);
pnp_set_irq(dev, 0x70, 1); /* IRQ 1 */
pnp_set_irq(dev, 0x72, 12); /* IRQ 12 */
pnp_set_enable(dev, 1);
pnp_exit_conf_state(dev);
}
static inline void kbc1100_early_init(unsigned port)
{
device_t dev;
dev = PNP_DEV (port, KBC1100_KBC);
pnp_enter_conf_state(dev);
/* Serial IRQ enabled */
outb(0x25, port);
outb(0x04, port + 1);
/* Enable SMSC UART 0 */
dev = PNP_DEV (port, SMSCSUPERIO_SP1);
pnp_set_logical_device(dev);
pnp_set_enable(dev, 0);
pnp_set_iobase(dev, PNP_IDX_IO0, CONFIG_TTYS0_BASE);
pnp_set_enable(dev, 1);
/* Enable keyboard */
dev = PNP_DEV (port, KBC1100_KBC);
pnp_set_logical_device(dev);
pnp_set_enable(dev, 0);
pnp_set_iobase(dev, PNP_IDX_IO0, 0x60);
pnp_set_iobase(dev, PNP_IDX_IO1, 0x64);
pnp_set_irq(dev, 0x70, 1); /* IRQ 1 */
pnp_set_irq(dev, 0x72, 12); /* IRQ 12 */
pnp_set_enable(dev, 1);
/* Enable EC Channel 0 */
dev = PNP_DEV (port, KBC1100_EC0);
pnp_set_logical_device(dev);
pnp_set_enable(dev, 1);
pnp_exit_conf_state(dev);
/* disable the 1s timer */
outb(0xE7, 0x64);
}
void shc4307_init(void)
{
shc4307_enter_ext_func_mode(CMOS_DEV);
pnp_set_logical_device(CMOS_DEV); /* CMOS/RTC */
pnp_set_iobase(CMOS_DEV, PNP_IDX_IO0, 0x70);
pnp_set_iobase(CMOS_DEV, PNP_IDX_IO1, 0x72);
pnp_set_irq(CMOS_DEV, PNP_IDX_IRQ0, 8);
/* pnp_set_enable(CMOS_DEV, 3); */
pnp_write_config(CMOS_DEV, 0x30, 3);
pnp_set_logical_device(KBD_DEV); /* Keyboard */
pnp_set_irq(KBD_DEV, PNP_IDX_IRQ0, 1);
pnp_set_enable(KBD_DEV, 1);
pnp_set_logical_device(DBG_DEV); /* Debug */
pnp_set_iobase(DBG_DEV, PNP_IDX_IO0, 0x80);
pnp_set_enable(DBG_DEV, 1);
pnp_set_logical_device(REGS_DEV);
pnp_set_iobase(REGS_DEV, PNP_IDX_IO0, 0x600);
pnp_set_enable(REGS_DEV, 1);
shc4307_exit_ext_func_mode(CMOS_DEV);
}
static void vt1211_pnp_set_resources(struct device *dev)
{
struct resource *res;
#if IS_ENABLED(CONFIG_CONSOLE_SERIAL) && IS_ENABLED(CONFIG_DRIVERS_UART_8250IO)
/* TODO: Do the same for SP2? */
if (dev->path.pnp.device == VT1211_SP1) {
for (res = dev->resource_list; res; res = res->next) {
res->flags |= IORESOURCE_STORED;
report_resource_stored(dev, res, "");
}
return;
}
#endif
pnp_enter_conf_mode(dev);
pnp_set_logical_device(dev);
/* Paranoia says I should disable the device here... */
for (res = dev->resource_list; res; res = res->next) {
if (!(res->flags & IORESOURCE_ASSIGNED)) {
printk(BIOS_ERR, "ERROR: %s %02lx %s size: 0x%010Lx "
"not assigned\n", dev_path(dev), res->index,
resource_type(res), res->size);
continue;
}
/* Now store the resource. */
if (res->flags & IORESOURCE_IO) {
vt1211_set_iobase(dev, res->index, res->base);
} else if (res->flags & IORESOURCE_DRQ) {
pnp_set_drq(dev, res->index, res->base);
} else if (res->flags & IORESOURCE_IRQ) {
pnp_set_irq(dev, res->index, res->base);
} else {
printk(BIOS_ERR, "ERROR: %s %02lx unknown resource "
"type\n", dev_path(dev), res->index);
return;
}
res->flags |= IORESOURCE_STORED;
report_resource_stored(dev, res, "");
}
pnp_exit_conf_mode(dev);
}
/* This box has one superio
* Also set up the GPIOs from the beginning. This is the "no schematic
* but safe anyways" method.
*/
static void early_superio_config_w83627ehg(void)
{
device_t dev;
dev = DUMMY_DEV;
pnp_enter_ext_func_mode(dev);
pnp_write_config(dev, 0x24, 0xc4); // PNPCSV
pnp_write_config(dev, 0x29, 0x01); // GPIO settings
pnp_write_config(dev, 0x2a, 0x40); // GPIO settings should be fc but gets set to 02
pnp_write_config(dev, 0x2b, 0xc0); // GPIO settings?
pnp_write_config(dev, 0x2c, 0x03); // GPIO settings?
pnp_write_config(dev, 0x2d, 0x20); // GPIO settings?
dev=PNP_DEV(0x4e, W83627EHG_SP1);
pnp_set_logical_device(dev);
pnp_set_enable(dev, 0);
pnp_set_iobase(dev, PNP_IDX_IO0, 0x3f8);
pnp_set_irq(dev, PNP_IDX_IRQ0, 4);
pnp_set_enable(dev, 1);
dev=PNP_DEV(0x4e, W83627EHG_SP2);
pnp_set_logical_device(dev);
pnp_set_enable(dev, 0);
pnp_set_iobase(dev, PNP_IDX_IO0, 0x2f8);
pnp_set_irq(dev, PNP_IDX_IRQ0, 3);
// pnp_write_config(dev, 0xf1, 4); // IRMODE0
pnp_set_enable(dev, 1);
dev=PNP_DEV(0x4e, W83627EHG_KBC); // Keyboard
pnp_set_logical_device(dev);
pnp_set_enable(dev, 0);
pnp_set_iobase(dev, PNP_IDX_IO0, 0x60);
pnp_set_iobase(dev, PNP_IDX_IO1, 0x64);
//pnp_write_config(dev, 0xf0, 0x82);
pnp_set_enable(dev, 1);
dev=PNP_DEV(0x4e, W83627EHG_GPIO2);
pnp_set_logical_device(dev);
pnp_set_enable(dev, 1); // Just enable it
dev=PNP_DEV(0x4e, W83627EHG_GPIO3);
pnp_set_logical_device(dev);
pnp_set_enable(dev, 0);
pnp_write_config(dev, 0xf0, 0xfb); // GPIO bit 2 is output
pnp_write_config(dev, 0xf1, 0x00); // GPIO bit 2 is 0
pnp_write_config(dev, 0x30, 0x03); // Enable GPIO3+4. pnp_set_enable is not sufficient
dev=PNP_DEV(0x4e, W83627EHG_FDC);
pnp_set_logical_device(dev);
pnp_set_enable(dev, 0);
dev=PNP_DEV(0x4e, W83627EHG_PP);
pnp_set_logical_device(dev);
pnp_set_enable(dev, 0);
/* Enable HWM */
dev=PNP_DEV(0x4e, W83627EHG_HWM);
pnp_set_logical_device(dev);
pnp_set_enable(dev, 0);
pnp_set_iobase(dev, PNP_IDX_IO0, 0xa00);
pnp_set_enable(dev, 1);
pnp_exit_ext_func_mode(dev);
}
/*
* Logical device 4, 5 and 7 are being deactivated. Logical Device 1 seems to
* be another serial (?), it is also deactivated on the HP machine.
*/
static void pilot_early_init(device_t dev)
{
unsigned port = dev >> 8;
print_debug("Using port: ");
print_debug_hex16(port);
print_debug("\n");
pilot_disable_serial(PNP_DEV(port, 0x1));
print_debug("disable serial 1\n");
pnp_enter_ext_func_mode(dev);
pnp_set_logical_device(PNP_DEV(port, 0x3));
pnp_set_enable(dev, 0);
pnp_set_iobase(dev, 0x60, 0x0b00);
pnp_set_iobase(dev, 0x62, 0x0b80);
pnp_set_iobase(dev, 0x64, 0x0b84);
pnp_set_iobase(dev, 0x66, 0x0b86);
pnp_set_enable(dev, 1);
pnp_exit_ext_func_mode(dev);
/*
pnp_enter_ext_func_mode(dev);
pnp_set_logical_device(PNP_DEV(port, 0x3));
pnp_exit_ext_func_mode(dev);
pnp_enter_ext_func_mode(dev);
pnp_set_enable(PNP_DEV(port, 0x3), 0);
pnp_exit_ext_func_mode(dev);
*/
pnp_enter_ext_func_mode(dev);
pnp_set_logical_device(PNP_DEV(port, 0x4));
pnp_exit_ext_func_mode(dev);
pnp_enter_ext_func_mode(dev);
pnp_set_enable( PNP_DEV(port, 0x4), 0);
pnp_exit_ext_func_mode(dev);
pnp_enter_ext_func_mode(dev);
pnp_set_logical_device(PNP_DEV(port, 0x5));
pnp_exit_ext_func_mode(dev);
pnp_enter_ext_func_mode(dev);
pnp_set_enable(PNP_DEV(port, 0x5), 0);
pnp_exit_ext_func_mode(dev);
pnp_enter_ext_func_mode(dev);
pnp_set_logical_device(PNP_DEV(port, 0x6));
pnp_set_enable(dev, 0);
pnp_set_iobase(dev, PNP_IDX_IO0, 0x60);
pnp_set_iobase(dev, PNP_IDX_IO1, 0x64);
pnp_set_irq(dev, PNP_IDX_IRQ0, 1);
pnp_set_drq(dev, 0x71, 3);
pnp_set_enable(dev, 0);
pnp_exit_ext_func_mode(dev);
pnp_enter_ext_func_mode(dev);
pnp_set_logical_device(PNP_DEV(port, 0xe));
pnp_set_enable(dev, 0);
pnp_set_iobase(dev, PNP_IDX_IO0, 0x70);
pnp_set_iobase(dev, PNP_IDX_IO1, 0x72);
pnp_set_irq(dev, PNP_IDX_IRQ0, 8);
pnp_set_drq(dev, 0x71, 3);
pnp_set_enable(dev, 0);
pnp_exit_ext_func_mode(dev);
pnp_enter_ext_func_mode(dev);
pnp_set_logical_device(PNP_DEV(port, 0x7));
pnp_exit_ext_func_mode(dev);
pnp_enter_ext_func_mode(dev);
pnp_set_enable(PNP_DEV(port, 0x7), 0);
pnp_exit_ext_func_mode(dev);
/*
pnp_enter_ext_func_mode(dev);
pnp_set_logical_device(PNP_DEV(port, 0x8));
pnp_exit_ext_func_mode(dev);
pnp_enter_ext_func_mode(dev);
pnp_set_enable(PNP_DEV(port, 0x8), 0);
pnp_exit_ext_func_mode(dev);
pnp_enter_ext_func_mode(dev);
pnp_set_logical_device(PNP_DEV(port, 0x9));
pnp_exit_ext_func_mode(dev);
pnp_enter_ext_func_mode(dev);
pnp_set_enable(PNP_DEV(port, 0x9), 0);
pnp_exit_ext_func_mode(dev);
pnp_enter_ext_func_mode(dev);
pnp_set_logical_device(PNP_DEV(port, 0x10));
pnp_exit_ext_func_mode(dev);
pnp_enter_ext_func_mode(dev);
pnp_set_enable(PNP_DEV(port, 0x10), 0);
pnp_exit_ext_func_mode(dev);
*/
}
