int board_init(void)
{
struct ccsr_scfg *scfg = (struct ccsr_scfg *)CONFIG_SYS_FSL_SCFG_ADDR;
#ifdef CONFIG_SECURE_BOOT
/*
* In case of Secure Boot, the IBR configures the SMMU
* to allow only Secure transactions.
* SMMU must be reset in bypass mode.
* Set the ClientPD bit and Clear the USFCFG Bit
*/
u32 val;
val = (in_le32(SMMU_SCR0) | SCR0_CLIENTPD_MASK) & ~(SCR0_USFCFG_MASK);
out_le32(SMMU_SCR0, val);
val = (in_le32(SMMU_NSCR0) | SCR0_CLIENTPD_MASK) & ~(SCR0_USFCFG_MASK);
out_le32(SMMU_NSCR0, val);
#endif
#ifdef CONFIG_FSL_CAAM
sec_init();
#endif
#ifdef CONFIG_FSL_LS_PPA
ppa_init();
#endif
/* invert AQR105 IRQ pins polarity */
out_be32(&scfg->intpcr, AQR105_IRQ_MASK);
return 0;
}
int board_init(void)
{
struct ccsr_cci400 *cci = (struct ccsr_cci400 *)(CONFIG_SYS_IMMR +
CONFIG_SYS_CCI400_OFFSET);
/*
* Set CCI-400 control override register to enable barrier
* transaction
*/
out_le32(&cci->ctrl_ord, CCI400_CTRLORD_EN_BARRIER);
#ifdef CONFIG_SYS_FSL_ERRATUM_A010315
erratum_a010315();
#endif
#ifdef CONFIG_ENV_IS_NOWHERE
gd->env_addr = (ulong)&default_environment[0];
#endif
#ifdef CONFIG_FSL_CAAM
sec_init();
#endif
#ifdef CONFIG_FSL_LS_PPA
ppa_init();
#endif
return 0;
}
int board_init(void)
{
#ifdef CONFIG_SYS_FSL_ERRATUM_A010315
erratum_a010315();
#endif
select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT);
board_retimer_init();
#ifdef CONFIG_SYS_FSL_SERDES
config_serdes_mux();
#endif
#ifdef CONFIG_FSL_LS_PPA
ppa_init();
#endif
return 0;
}
int board_init(void)
{
select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT);
#ifdef CONFIG_SYS_FSL_SERDES
config_serdes_mux();
#endif
#ifdef CONFIG_LAYERSCAPE_NS_ACCESS
enable_layerscape_ns_access();
#endif
if (adjust_vdd(0))
printf("Warning: Adjusting core voltage failed.\n");
#ifdef CONFIG_FSL_LS_PPA
ppa_init();
#endif
#ifdef CONFIG_SECURE_BOOT
/*
* In case of Secure Boot, the IBR configures the SMMU
* to allow only Secure transactions.
* SMMU must be reset in bypass mode.
* Set the ClientPD bit and Clear the USFCFG Bit
*/
u32 val;
val = (in_le32(SMMU_SCR0) | SCR0_CLIENTPD_MASK) & ~(SCR0_USFCFG_MASK);
out_le32(SMMU_SCR0, val);
val = (in_le32(SMMU_NSCR0) | SCR0_CLIENTPD_MASK) & ~(SCR0_USFCFG_MASK);
out_le32(SMMU_NSCR0, val);
#endif
#ifdef CONFIG_FSL_CAAM
sec_init();
#endif
return 0;
}
void spl_board_init(void)
{
#if defined(CONFIG_SECURE_BOOT) && defined(CONFIG_FSL_LSCH2)
/*
* In case of Secure Boot, the IBR configures the SMMU
* to allow only Secure transactions.
* SMMU must be reset in bypass mode.
* Set the ClientPD bit and Clear the USFCFG Bit
*/
u32 val;
val = (in_le32(SMMU_SCR0) | SCR0_CLIENTPD_MASK) & ~(SCR0_USFCFG_MASK);
out_le32(SMMU_SCR0, val);
val = (in_le32(SMMU_NSCR0) | SCR0_CLIENTPD_MASK) & ~(SCR0_USFCFG_MASK);
out_le32(SMMU_NSCR0, val);
#endif
#ifdef CONFIG_LAYERSCAPE_NS_ACCESS
enable_layerscape_ns_access();
#endif
#ifdef CONFIG_SPL_FSL_LS_PPA
ppa_init();
#endif
}
