void spi1_arch_init(void) {
// set dma options
spi1_dma.spidr = (uint32_t)&SPI1_DR;
spi1_dma.dma = DMA1;
spi1_dma.rx_chan = DMA_CHANNEL2;
spi1_dma.tx_chan = DMA_CHANNEL3;
spi1_dma.rx_nvic_irq = NVIC_DMA1_CHANNEL2_IRQ;
spi1_dma.tx_nvic_irq = NVIC_DMA1_CHANNEL3_IRQ;
spi1_dma.tx_dummy_buf = 0;
spi1_dma.tx_extra_dummy_dma = FALSE;
spi1_dma.rx_dummy_buf = 0;
spi1_dma.rx_extra_dummy_dma = FALSE;
// set the default configuration
set_default_comm_config(&spi1_dma.comm);
spi1_dma.comm_sig = get_comm_signature(&spi1_dma.comm);
// set init struct, indices and status
spi1.reg_addr = (void *)SPI1;
spi1.init_struct = &spi1_dma;
spi1.trans_insert_idx = 0;
spi1.trans_extract_idx = 0;
spi1.status = SPIIdle;
// Enable SPI1 Periph and gpio clocks
rcc_peripheral_enable_clock(&RCC_APB2ENR, RCC_APB2ENR_SPI1EN);
// Configure GPIOs: SCK, MISO and MOSI
gpio_set_mode(GPIO_BANK_SPI1_SCK, GPIO_MODE_OUTPUT_50_MHZ,
GPIO_CNF_OUTPUT_ALTFN_PUSHPULL,
GPIO_SPI1_SCK | GPIO_SPI1_MOSI);
gpio_set_mode(GPIO_BANK_SPI1_MISO, GPIO_MODE_INPUT, GPIO_CNF_INPUT_FLOAT,
GPIO_SPI1_MISO);
// reset SPI
spi_reset(SPI1);
// Disable SPI peripheral
spi_disable(SPI1);
// Force SPI mode over I2S.
SPI1_I2SCFGR = 0;
// configure master SPI.
spi_init_master(SPI1, spi1_dma.comm.br, spi1_dma.comm.cpol, spi1_dma.comm.cpha,
spi1_dma.comm.dff, spi1_dma.comm.lsbfirst);
/*
* Set NSS management to software.
*
* Note:
* Setting nss high is very important, even if we are controlling the GPIO
* ourselves this bit needs to be at least set to 1, otherwise the spi
* peripheral will not send any data out.
*/
spi_enable_software_slave_management(SPI1);
spi_set_nss_high(SPI1);
// Enable SPI_1 DMA clock
rcc_peripheral_enable_clock(&RCC_AHBENR, RCC_AHBENR_DMA1EN);
// Enable SPI1 periph.
spi_enable(SPI1);
spi_arch_int_enable(&spi1);
}
int devspi_create(const struct spi_config *conf)
{
struct dev_spi *spi = NULL;
if (!conf)
return -EINVAL;
if (conf->base == 0)
return -EINVAL;
if ((conf->idx < 0) || (conf->idx > MAX_SPIS))
return -EINVAL;
spi = kalloc(sizeof(struct dev_spi));
if (!spi)
return -ENOMEM;
/* Claim pins for SCK/MOSI/MISO */
gpio_create(&mod_spi, &conf->pio_sck);
gpio_create(&mod_spi, &conf->pio_mosi);
gpio_create(&mod_spi, &conf->pio_miso);
/* Erase spi content */
memset(spi, 0, sizeof(struct dev_spi));
/* Enable clocks */
rcc_periph_clock_enable(conf->rcc);
rcc_periph_clock_enable(conf->dma_rcc);
/* Startup routine */
//spi_disable(conf->base);
/**********************************/
/* reset SPI1 */
spi_reset(conf->base);
/* init SPI1 master */
spi_init_master(conf->base,
SPI_CR1_BAUDRATE_FPCLK_DIV_64,
SPI_CR1_CPOL_CLK_TO_0_WHEN_IDLE,
SPI_CR1_CPHA_CLK_TRANSITION_1,
SPI_CR1_DFF_8BIT,
SPI_CR1_MSBFIRST);
/* enable SPI1 first */
spi_enable(conf->base);
/**********************************/
#if 0
spi_set_master_mode(conf->base);
spi_set_baudrate_prescaler(conf->base, SPI_CR1_BR_FPCLK_DIV_256); /* TODO: Calculate prescaler from baudrate */
if(conf->polarity == 0)
spi_set_clock_polarity_0(conf->base);
else
spi_set_clock_polarity_1(conf->base);
if(conf->phase == 0) spi_set_clock_phase_0(conf->base);
else
spi_set_clock_phase_1(conf->base);
if(conf->rx_only == 0)
spi_set_full_duplex_mode(conf->base);
else
spi_set_receive_only_mode(conf->base);
if(conf->bidir_mode == 0)
spi_set_unidirectional_mode(conf->base);
else
spi_set_bidirectional_mode(conf->base);
if(conf->dff_16)
spi_set_dff_16bit(conf->base);
else
spi_set_dff_8bit(conf->base);
if(conf->enable_software_slave_management)
spi_enable_software_slave_management(conf->base);
else
spi_disable_software_slave_management(conf->base);
if(conf->send_msb_first)
spi_send_msb_first(conf->base);
else
spi_send_lsb_first(conf->base);
spi_set_nss_high(conf->base);
#endif
/* Set up device struct */
spi->base = conf->base;
spi->irq = conf->irq;
//spi->tx_dma_config = &conf->tx_dma;
//spi->rx_dma_config = &conf->rx_dma;
spi->mutex = mutex_init();
/* Store address in the DEV_SPI array. */
DEV_SPI[conf->idx] = spi;
/* Enable interrupts */
//nvic_set_priority(conf->irq, 1);
//nvic_enable_irq(conf->irq);
return 0;
}
/**
* Start a new transaction with DMA.
*/
static void spi_start_dma_transaction(struct spi_periph* periph, struct spi_transaction* trans)
{
struct spi_periph_dma *dma;
uint8_t sig = 0x00;
/* Store local copy to notify of the results */
trans->status = SPITransRunning;
periph->status = SPIRunning;
dma = periph->init_struct;
/*
* Check if we need to reconfigure the spi peripheral for this transaction
*/
sig = get_transaction_signature(trans);
if (sig != dma->comm_sig) {
/* A different config is required in this transaction... */
set_comm_from_transaction(&(dma->comm), trans);
/* remember the new conf signature */
dma->comm_sig = sig;
/* apply the new configuration */
spi_disable((uint32_t)periph->reg_addr);
spi_init_master((uint32_t)periph->reg_addr, dma->comm.br, dma->comm.cpol,
dma->comm.cpha, dma->comm.dff, dma->comm.lsbfirst);
spi_enable_software_slave_management((uint32_t)periph->reg_addr);
spi_set_nss_high((uint32_t)periph->reg_addr);
spi_enable((uint32_t)periph->reg_addr);
}
/*
* Select the slave after reconfiguration of the peripheral
*/
if (trans->select == SPISelectUnselect || trans->select == SPISelect) {
SpiSlaveSelect(trans->slave_idx);
}
/* Run the callback AFTER selecting the slave */
if (trans->before_cb != 0) {
trans->before_cb(trans);
}
/*
* Receive DMA channel configuration ----------------------------------------
*
* We always run the receive DMA until the very end!
* This is done so we can use the transfer complete interrupt
* of the RX DMA to signal the end of the transaction.
*
* If we want to receive less than we transmit, a dummy buffer
* for the rx DMA is used after for the remaining data.
*
* In the transmit only case (input_length == 0),
* the dummy is used right from the start.
*/
if (trans->input_length == 0) {
/* run the dummy rx dma for the complete transaction length */
spi_configure_dma(dma->dma, dma->rx_chan, (uint32_t)dma->spidr,
(uint32_t)&(dma->rx_dummy_buf), trans->output_length, trans->dss, FALSE);
} else {
/* run the real rx dma for input_length */
spi_configure_dma(dma->dma, dma->rx_chan, (uint32_t)dma->spidr,
(uint32_t)trans->input_buf, trans->input_length, trans->dss, TRUE);
/* use dummy rx dma for the rest */
if (trans->output_length > trans->input_length) {
/* Enable use of second dma transfer with dummy buffer (cleared in ISR) */
dma->rx_extra_dummy_dma = TRUE;
}
}
dma_set_read_from_peripheral(dma->dma, dma->rx_chan);
dma_set_priority(dma->dma, dma->rx_chan, DMA_CCR_PL_VERY_HIGH);
/*
* Transmit DMA channel configuration ---------------------------------------
*
* We always run the transmit DMA!
* To receive data, the clock must run, so something has to be transmitted.
* If needed, use a dummy DMA transmitting zeros for the remaining length.
*
* In the reveive only case (output_length == 0),
* the dummy is used right from the start.
*/
if (trans->output_length == 0) {
spi_configure_dma(dma->dma, dma->tx_chan, (uint32_t)dma->spidr,
(uint32_t)&(dma->tx_dummy_buf), trans->input_length, trans->dss, FALSE);
} else {
spi_configure_dma(dma->dma, dma->tx_chan, (uint32_t)dma->spidr,
(uint32_t)trans->output_buf, trans->output_length, trans->dss, TRUE);
if (trans->input_length > trans->output_length) {
/* Enable use of second dma transfer with dummy buffer (cleared in ISR) */
dma->tx_extra_dummy_dma = TRUE;
}
}
dma_set_read_from_memory(dma->dma, dma->tx_chan);
dma_set_priority(dma->dma, dma->tx_chan, DMA_CCR_PL_MEDIUM);
/* Enable DMA transfer complete interrupts. */
dma_enable_transfer_complete_interrupt(dma->dma, dma->rx_chan);
dma_enable_transfer_complete_interrupt(dma->dma, dma->tx_chan);
/* Enable DMA channels */
dma_enable_channel(dma->dma, dma->rx_chan);
dma_enable_channel(dma->dma, dma->tx_chan);
/* Enable SPI transfers via DMA */
spi_enable_rx_dma((uint32_t)periph->reg_addr);
spi_enable_tx_dma((uint32_t)periph->reg_addr);
}
void codecInit(void)
{
memset(adcBuffer, 0xaa, sizeof(adcBuffer));
// I2S2 alternate function mapping
gpio_mode_setup(GPIOB, GPIO_MODE_AF, GPIO_PUPD_NONE, GPIO12 | GPIO13 | GPIO14 | GPIO15);
gpio_set_af(GPIOB, GPIO_AF5, GPIO12 | GPIO13 | GPIO15);
gpio_set_af(GPIOB, GPIO_AF6, GPIO14); // I2S2ext_SD (I2S receive)
gpio_mode_setup(GPIOC, GPIO_MODE_AF, GPIO_PUPD_NONE, GPIO6);
gpio_set_af(GPIOC, GPIO_AF5, GPIO6); // MCLK
gpio_set_output_options(GPIOB, GPIO_OTYPE_PP, GPIO_OSPEED_25MHZ, GPIO12 | GPIO13 | GPIO15);
gpio_set_output_options(GPIOC, GPIO_OTYPE_PP, GPIO_OSPEED_100MHZ, GPIO6);
// Set up SPI1
spi_reset(SPI1);
spi_init_master(SPI1, SPI_CR1_BAUDRATE_FPCLK_DIV_256, SPI_CR1_CPOL_CLK_TO_1_WHEN_IDLE,
SPI_CR1_CPHA_CLK_TRANSITION_2, SPI_CR1_DFF_16BIT, SPI_CR1_MSBFIRST);
spi_set_nss_high(SPI1);
spi_enable_software_slave_management(SPI1);
spi_enable(SPI1);
// SPI1 alternate function mapping, set CSB signal high output
gpio_mode_setup(GPIOA, GPIO_MODE_AF, GPIO_PUPD_NONE, GPIO5 | GPIO7);
gpio_set_af(GPIOA, GPIO_AF5, GPIO5 | GPIO7);
gpio_set(GPIOA, GPIO4);
gpio_mode_setup(GPIOA, GPIO_MODE_OUTPUT, GPIO_PUPD_NONE, GPIO4);
codecConfig();
// Set up I2S for 48kHz 16-bit stereo.
// The input to the PLLI2S is 1MHz. Division factors are from
// table 126 in the data sheet.
//
// This gives us 1.536MHz SCLK = 16 bits * 2 channels * 48000 Hz
// and 12.288 MHz MCLK = 256 * 48000 Hz
spi_reset(SPI2);
RCC_PLLI2SCFGR = (3 << 28) | (258 << 6);
RCC_CR |= RCC_CR_PLLI2SON;
while (!(RCC_CR & RCC_CR_PLLI2SRDY));
const unsigned i2sdiv = 3;
SPI_I2SPR(SPI2) = SPI_I2SPR_MCKOE | SPI_I2SPR_ODD | i2sdiv;
SPI_I2SCFGR(SPI2) |= SPI_I2SCFGR_I2SMOD | SPI_I2SCFGR_I2SE |
(SPI_I2SCFGR_I2SCFG_MASTER_TRANSMIT << SPI_I2SCFGR_I2SCFG_LSB);
SPI_I2SCFGR(I2S2_EXT_BASE) = SPI_I2SCFGR_I2SMOD | SPI_I2SCFGR_I2SE |
(SPI_I2SCFGR_I2SCFG_SLAVE_RECEIVE << SPI_I2SCFGR_I2SCFG_LSB);
// Configure the DMA engine to stream data to the DAC.
dma_stream_reset(DMA1, DAC_DMA_STREAM);
dma_set_peripheral_address(DMA1, DAC_DMA_STREAM, (intptr_t)&SPI_DR(SPI2));
dma_set_memory_address(DMA1, DAC_DMA_STREAM, (intptr_t)dacBuffer[0]);
dma_set_memory_address_1(DMA1, DAC_DMA_STREAM, (intptr_t)dacBuffer[1]);
dma_set_number_of_data(DMA1, DAC_DMA_STREAM, BUFFER_SAMPLES);
dma_channel_select(DMA1, DAC_DMA_STREAM, DAC_DMA_CHANNEL);
dma_set_transfer_mode(DMA1, DAC_DMA_STREAM, DMA_SxCR_DIR_MEM_TO_PERIPHERAL);
dma_set_memory_size(DMA1, DAC_DMA_STREAM, DMA_SxCR_MSIZE_16BIT);
dma_set_peripheral_size(DMA1, DAC_DMA_STREAM, DMA_SxCR_PSIZE_16BIT);
dma_enable_memory_increment_mode(DMA1, DAC_DMA_STREAM);
dma_enable_double_buffer_mode(DMA1, DAC_DMA_STREAM);
dma_enable_stream(DMA1, DAC_DMA_STREAM);
// Configure the DMA engine to stream data from the ADC.
dma_stream_reset(DMA1, ADC_DMA_STREAM);
dma_set_peripheral_address(DMA1, ADC_DMA_STREAM, (intptr_t)&SPI_DR(I2S2_EXT_BASE));
dma_set_memory_address(DMA1, ADC_DMA_STREAM, (intptr_t)adcBuffer[0]);
dma_set_memory_address_1(DMA1, ADC_DMA_STREAM, (intptr_t)adcBuffer[1]);
dma_set_number_of_data(DMA1, ADC_DMA_STREAM, BUFFER_SAMPLES);
dma_channel_select(DMA1, ADC_DMA_STREAM, ADC_DMA_CHANNEL);
dma_set_transfer_mode(DMA1, ADC_DMA_STREAM, DMA_SxCR_DIR_PERIPHERAL_TO_MEM);
dma_set_memory_size(DMA1, ADC_DMA_STREAM, DMA_SxCR_MSIZE_16BIT);
dma_set_peripheral_size(DMA1, ADC_DMA_STREAM, DMA_SxCR_PSIZE_16BIT);
dma_enable_memory_increment_mode(DMA1, ADC_DMA_STREAM);
dma_enable_double_buffer_mode(DMA1, ADC_DMA_STREAM);
dma_enable_stream(DMA1, ADC_DMA_STREAM);
// Enable interrupts on finished DMA transfers
dma_enable_transfer_complete_interrupt(DMA1, DAC_DMA_STREAM);
nvic_enable_irq(NVIC_DMA1_STREAM4_IRQ);
// Start transmitting data
spi_enable_rx_dma(I2S2_EXT_BASE);
spi_enable_tx_dma(SPI2);
}
