void user_init(void) {
stdoutInit();
ioInit();
httpdInit(builtInUrls, 80);
dnsserver_init();
os_printf("\nReady\n");
}
//Main routine. Initialize stdout, the I/O, filesystem and the webserver and we're done.
void user_init(void) {
wifi_station_set_auto_connect(FALSE);
stdoutInit();
CFG_Load();
ioInit();
MAIN_DEBUG("\nInitialise ENC stack, dhcp if requested\n");
stack_init();
/* This DNS is only for the wifi interface, as wired never acts as an 'AP' */
captdnsInit();
// 0x40200000 is the base address for spi flash memory mapping, ESPFS_POS is the position
// where image is written in flash that is defined in Makefile.
#ifdef ESPFS_POS
espFsInit((void*)(0x40200000 + ESPFS_POS));
#else
espFsInit((void*)(webpages_espfs_start));
#endif
httpdInit(builtInUrls, 80);
#ifdef SHOW_HEAP_USE
os_timer_disarm(&prHeapTimer);
os_timer_setfn(&prHeapTimer, prHeapTimerCb, NULL);
os_timer_arm(&prHeapTimer, 3000, 1);
#endif
os_timer_disarm(&websockTimer);
os_timer_setfn(&websockTimer, websockTimerCb, NULL);
os_timer_arm(&websockTimer, 1000, 1);
os_printf("\nReady\n");
}
// Main routine, initialize some basic stuff
void ICACHE_FLASH_ATTR user_init(void)
{
// Init some stuff
stdoutInit();
batteryInit();
configInit();
configLoad();
// Check if wifi mode is correct
configCheckWifiMode();
// Measure battery voltage
batteryMeasureVoltage();
if(!batteryCheckVoltage())
{
// Voltage too low, go to sleep mode!
sleepmode();
}
// 0x40200000 is the base address for spi flash memory mapping, ESPFS_POS is the position
// where image is written in flash that is defined in Makefile.
espFsInit((void*)(0x40200000 + ESPFS_POS));
httpdInit(builtInUrls, 80);
// Register callback
system_init_done_cb(init_done);
os_printf("Ready\n");
}
//Init function
void ICACHE_FLASH_ATTR user_init() {
//uart_init(BIT_RATE_115200,BIT_RATE_115200);
flashData = &_flashData;
IPStation = ipstation;
stdoutInit();
char ssid[32] = SSID;
char password[64] = SSID_PASSWORD;
struct station_config stationConf;
os_printf("\ninit\n");
user_init_gpio();
//Set station mode & AP mode
// wifi_set_opmode(STATION_MODE);
wifi_set_opmode(STATIONAP_MODE);
initFlash();
flash_read();
//if (flashData->magic != MAGIC_NUM)
{
//Set ap settings
os_memcpy(&stationConf.ssid, ssid, 32);
os_memcpy(&stationConf.password, password, 64);
}
// else
// {
// os_memcpy(&stationConf.ssid, flashData->ssid, 32);
// os_memcpy(&stationConf.password, flashData->password, 64);
//
// }
wifi_station_set_config(&stationConf);
os_printf("\nConnecting to %s, %s\n", stationConf.ssid, stationConf.password);
SetSetverMode();
//Start os task
system_os_task(loop, user_procTaskPrio,user_procTaskQueue, user_procTaskQueueLen);
system_os_post(user_procTaskPrio, 0, 0 );
os_printf("\nInitializing Network\n");
network_init();
}
/************************************************
* name: user_init
* parameters: none
* return value: none
* purpose: main logic
************************************************/
void user_init(void)
{
/* initialization */
struct softap_config tWifiSettings = { 0 };
uint8 puMacAddress[6] = { 0 };
os_memset((void *)&tWifiSettings, 0, sizeof(tWifiSettings));
wifi_softap_get_config(&tWifiSettings);
/* retrieve mac address */
wifi_get_macaddr(1, puMacAddress);
/* append to ssid name */
memcpy(tWifiSettings.ssid, HOTSPOT_SSID_STRING, sizeof(HOTSPOT_SSID_STRING));
os_sprintf(tWifiSettings.ssid + sizeof(HOTSPOT_SSID_STRING) - 1, "%x%x%x%x%x%x", puMacAddress[0],
puMacAddress[1],
puMacAddress[2],
puMacAddress[3],
puMacAddress[4],
puMacAddress[5]);
/* set password */
memcpy(tWifiSettings.password, HOTSPOT_PASSWORD_STRING, os_strlen(HOTSPOT_PASSWORD_STRING));
/* update other settings */
tWifiSettings.authmode = AUTH_WPA_WPA2_PSK;
tWifiSettings.ssid_len = 0;
tWifiSettings.channel = 6;
tWifiSettings.max_connection = 4;
/* update wifi configuration */
wifi_softap_set_config(&tWifiSettings);
/* initialize stdout */
stdoutInit();
/* initialize IOs */
ioInit();
/* initialize server */
httpdInit(g_ptSupportedUrls, 80);
#ifdef USER_MAIN_DEBUG
os_printf("user_init: ready; partition %d\n", system_upgrade_userbin_check());
#endif
}
//Main routine. Initialize stdout, the I/O and the webserver and we're done.
void user_init(void) {
// HTTPD
stdoutInit();
ioInit();
httpdInit(builtInUrls, 80);
//MQTT
uart_init(115200, 115200);
CFG_Load();
sleepms(1000);
MQTT_InitConnection(&mqttClient, sysCfg.mqtt_host, sysCfg.mqtt_port, SEC_NONSSL);
//MQTT_InitConnection(&mqttClient, "192.168.11.122", 1880, 0);
MQTT_InitClient(&mqttClient, sysCfg.device_id, sysCfg.mqtt_user, sysCfg.mqtt_pass, sysCfg.mqtt_keepalive, 1);
//MQTT_InitClient(&mqttClient, "client_id", "user", "pass", 120, 1);
// MQTT_InitLWT(&mqttClient, "/lwt", "offline", 0, 0);
MQTT_OnConnected(&mqttClient, mqttConnectedCb);
MQTT_OnDisconnected(&mqttClient, mqttDisconnectedCb);
MQTT_OnPublished(&mqttClient, mqttPublishedCb);
MQTT_OnData(&mqttClient, mqttDataCb);
INFO("device_ID:%s\r\n",sysCfg.device_id);
INFO("MQTTHOST:%s\r\n",sysCfg.mqtt_host);
//DS18B20 timers
os_timer_disarm(&ds18b20_timer);
os_timer_setfn(&ds18b20_timer, (os_timer_func_t *)ds18b20_cb, (void *)0);
os_timer_arm(&ds18b20_timer, DELAY, 1);
//NTP timers
ntp_get_time();
os_timer_disarm(&NTP_timer);
os_timer_setfn(&NTP_timer, (os_timer_func_t *)ntp_get_time, (void *)0);
os_timer_arm(&NTP_timer, NTPDELAY, 1);
// initialize GPIO2
PIN_FUNC_SELECT(PIN_GPIO2_MUX, PIN_GPIO2_FUNC);
GPIO_OUTPUT_SET(PIN_GPIO2, 0);
INFO("GPIO2 set to OFF\r\n");
WIFI_Connect(sysCfg.sta_ssid, sysCfg.sta_pwd, wifiConnectCb);
os_printf("\nReady\n");
}
//Main routine. Initialize stdout, the I/O, filesystem and the webserver and we're done.
void user_init(void) {
stdoutInit();
ioInit();
captdnsInit();
// 0x40200000 is the base address for spi flash memory mapping, ESPFS_POS is the position
// where image is written in flash that is defined in Makefile.
#ifdef ESPFS_POS
espFsInit((void*)(0x40200000 + ESPFS_POS));
#else
espFsInit((void*)(webpages_espfs_start));
#endif
httpdInit(builtInUrls, 80);
#ifdef SHOW_HEAP_USE
os_timer_disarm(&prHeapTimer);
os_timer_setfn(&prHeapTimer, prHeapTimerCb, NULL);
os_timer_arm(&prHeapTimer, 3000, 1);
#endif
os_printf("\nReady\n");
}
//Main routine
void ICACHE_FLASH_ATTR user_init(void) {
stdoutInit();
os_delay_us(100000);
CFG_Load();
ioInit();
WIFI_Connect(wifiConnectCb);
httpdInit(builtInUrls, sysCfg.httpd_port);
if(sysCfg.ntp_enable==1) {
sntp_init(sysCfg.ntp_tz); //timezone
}
if(sysCfg.mqtt_enable==1) {
MQTT_InitConnection(&mqttClient, (uint8_t *)sysCfg.mqtt_host, sysCfg.mqtt_port, sysCfg.mqtt_use_ssl );
MQTT_InitClient(&mqttClient, (uint8_t *)sysCfg.mqtt_devid, (uint8_t *)sysCfg.mqtt_user, (uint8_t *)sysCfg.mqtt_pass, sysCfg.mqtt_keepalive,1);
MQTT_OnConnected(&mqttClient, mqttConnectedCb);
MQTT_OnDisconnected(&mqttClient, mqttDisconnectedCb);
MQTT_OnPublished(&mqttClient, mqttPublishedCb);
MQTT_OnData(&mqttClient, mqttDataCb);
}
if(sysCfg.sensor_dht22_enable)
DHTInit(SENSOR_DHT22, 30000);
if(sysCfg.sensor_ds18b20_enable)
ds_init(30000);
broadcastd_init();
thermostat_init(30000);
/*
//Netbios to set the name
struct softap_config wiconfig;
os_memset(netbios_name, ' ', sizeof(netbios_name)-1);
if(wifi_softap_get_config(&wiconfig)) {
int i;
for(i = 0; i < sizeof(netbios_name)-1; i++) {
if(wiconfig.ssid[i] < ' ') break;
netbios_name[i] = wiconfig.ssid[i];
};
}
else os_sprintf(netbios_name, "ESP8266");
netbios_name[sizeof(netbios_name)-1]='\0';
netbios_init();
*/
os_printf("\nRelay Board Ready\n");
os_printf("Free heap size:%d\n",system_get_free_heap_size());
#ifdef CGIPWM_H
//Mind the PWM pin!! defined in pwm.h
duty=0;
pwm_init( 50, &duty);
pwm_set_duty(duty, 0);
pwm_start();
#endif
//OLEDInit();
}
//Main routine. Initialize stdout, the I/O and the webserver and we're done.
void user_init(void) {
// my stuff
dBR_BOILER_SET=65; // default setting 65C boiler temperature on reboot
dBR_TEMP_ROOM_SET=18; // default setting 18C room temperature on reboot
dBR_HUMIDITY_SET=60; // default setting 65% humidity target on reboot
dBR_MODE=2; // default BR MODE is AUTO
dDEVICE_MODE=1; // This mode defines if device uses remote (MQTT) management or uses local logics - 0 for remote, 1 for local mode. DEFAULT is 0 - remote
// HTTPD
stdoutInit();
ioInit();
httpdInit(builtInUrls, 80);
//MQTT
uart_init(115200, 115200);
CFG_Load();
sleepms(1000);
MQTT_InitConnection(&mqttClient, sysCfg.mqtt_host, sysCfg.mqtt_port, SEC_NONSSL);
//MQTT_InitConnection(&mqttClient, "192.168.11.122", 1880, 0);
MQTT_InitClient(&mqttClient, sysCfg.device_id, sysCfg.mqtt_user, sysCfg.mqtt_pass, sysCfg.mqtt_keepalive, 1);
//MQTT_InitClient(&mqttClient, "client_id", "user", "pass", 120, 1);
// MQTT_InitLWT(&mqttClient, "/lwt", "offline", 0, 0);
MQTT_OnConnected(&mqttClient, mqttConnectedCb);
MQTT_OnDisconnected(&mqttClient, mqttDisconnectedCb);
MQTT_OnPublished(&mqttClient, mqttPublishedCb);
MQTT_OnData(&mqttClient, mqttDataCb);
INFO("device_ID:%s\r\n",sysCfg.device_id);
INFO("MQTTHOST:%s\r\n",sysCfg.mqtt_host);
//DS18B20 timers
os_timer_disarm(&ds18b20_timer);
os_timer_setfn(&ds18b20_timer, (os_timer_func_t *)ds18b20_cb, (void *)0);
os_timer_arm(&ds18b20_timer, DELAY, 1);
// DHT22 initialize
DHTInit(DHT22, DELAY);
os_timer_disarm(&dht22_timer);
os_timer_setfn(&dht22_timer, (os_timer_func_t *)dht22_cb, (void *)0);
os_timer_arm(&dht22_timer, DELAY, 1);
// INPUT PIN initialize
ETS_GPIO_INTR_DISABLE(); // Disable gpio interrupts
ETS_GPIO_INTR_ATTACH(read_input_pin, 13); // GPIO13 interrupt handler
PIN_FUNC_SELECT(PIN_GPIO13_MUX, PIN_GPIO13_FUNC);
gpio_output_set(0, 0, 0, BIT13); // Set GPIO13 as input
PIN_PULLUP_EN(PIN_GPIO13_MUX); // Enable pullup
GPIO_REG_WRITE(GPIO_STATUS_W1TC_ADDRESS, BIT(13)); // Clear GPIO12 status
gpio_pin_intr_state_set(GPIO_ID_PIN(13), GPIO_PIN_INTR_NEGEDGE); // Interrupt on NEGATIVE GPIO13 edge
ETS_GPIO_INTR_ENABLE(); // Enable gpio interrupts
// INFO("Input pin INITIALIZED ! ! !");
// initialize GPIO12
PIN_FUNC_SELECT(PIN_GPIO12_MUX, PIN_GPIO12_FUNC);
GPIO_OUTPUT_SET(PIN_GPIO12, 0);
// INFO("GPIO12 set to OFF\r\n");
// initialize GPIO5
GPIO_OUTPUT_SET(PIN_GPIO5, 0);
// INFO("GPIO5 set to OFF\r\n");
// initialize GPIO14
PIN_FUNC_SELECT(PIN_GPIO14_MUX, PIN_GPIO14_FUNC);
GPIO_OUTPUT_SET(PIN_GPIO14, 0);
// INFO("GPIO14 set to OFF\r\n");
WIFI_Connect(sysCfg.sta_ssid, sysCfg.sta_pwd, wifiConnectCb);
os_printf("\nReady\n");
}