int __init device_init_stb840_promSvyaz(int ver)
{
struct sysconf_field *sc;
stx7105_configure_sata(0);
/* Set SPI Boot pads as inputs to avoid contention with SSC1 */
gpio_request(stm_gpio(15, 0), "SPI Boot CLK");
gpio_direction_input(stm_gpio(15, 0));
gpio_request(stm_gpio(15, 1), "SPI Boot DOUT");
gpio_direction_input(stm_gpio(15, 1));
gpio_request(stm_gpio(15, 2), "SPI Boot NOTCS");
gpio_direction_input(stm_gpio(15, 2));
gpio_request(stm_gpio(15, 3), "SPI Boot DIN");
gpio_direction_input(stm_gpio(15, 3));
/*
* Fix the reset chain so it correct to start with in case the
* watchdog expires or we trigger a reset.
*/
sc = sysconf_claim(SYS_CFG, 9, 27, 28, "reset_chain");
sysconf_write(sc, 0);
/* Release the sysconf bits so the coprocessor driver can claim them */
sysconf_release(sc);
/* I2C_xxxA - HDMI */
stx7105_configure_ssc_i2c(0, &(struct stx7105_ssc_config) {
.routing.ssc0.sclk = stx7105_ssc0_sclk_pio2_2,
.routing.ssc0.mtsr = stx7105_ssc0_mtsr_pio2_3, });
extern int board_init(void)
{
configPIO();
/*
* Note each EMI bank can only be a maximum of 64MiB.
* set CSA (Bank #0) to be 64MiB (0x00000000 to 0x03ffffff)
* set CSB (Bank #1) to be 64MiB (0x04000000 to 0x07ffffff)
*/
*ST40_EMI_BASEADDRESS(0) = (0) >> 22; /* start of EMI Bank #0 */
*ST40_EMI_BASEADDRESS(1) = ( 64<<20) >> 22; /* start of EMI Bank #1 */
*ST40_EMI_BASEADDRESS(2) = (128<<20) >> 22; /* start of EMI Bank #2 */
#ifdef QQQ /* QQQ - DELETE */
#if defined(CONFIG_SH_STM_SATA)
stx7105_configure_sata ();
#endif /* CONFIG_SH_STM_SATA */
#endif /* QQQ - DELETE */
#ifdef CONFIG_DRIVER_NET_STM_GMAC
/* Reset the PHY */
stmac_phy_reset();
#if CFG_STM_STMAC_BASE == CFG_STM_STMAC0_BASE /* MII0, via MoCA Module */
#error U-Boot does not support MoCA!
stx7108_configure_ethernet(0, &(struct stx7108_ethernet_config) {
.mode = stx7108_ethernet_mode_mii,
.ext_clk = 1,
.phy_bus = 0, });
extern int board_init(void)
{
configPIO();
#ifdef QQQ /* QQQ - DELETE */
#if defined(CONFIG_ST40_STM_SATA)
stx7105_configure_sata ();
#endif /* CONFIG_ST40_STM_SATA */
#endif /* QQQ - DELETE */
#ifdef CONFIG_DRIVER_NET_STM_GMAC
#if CONFIG_SYS_STM_STMAC_BASE == CONFIG_SYS_STM_STMAC0_BASE /* MII0, on CN18 */
stx7108_configure_ethernet(0, &(struct stx7108_ethernet_config) {
.mode = stx7108_ethernet_mode_mii,
.ext_clk = 1,
.phy_bus = 0, });
