void main(void) {
volatile packet_t *p;
volatile uint8_t t=20;
uint8_t chan;
char c;
gpio_data(0);
gpio_pad_dir_set( 1ULL << LED );
/* read from the data register instead of the pad */
/* this is needed because the led clamps the voltage low */
gpio_data_sel( 1ULL << LED);
/* trim the reference osc. to 24MHz */
trim_xtal();
uart_init(UART1, 115200);
vreg_init();
maca_init();
/* sets up tx_on, should be a board specific item */
*GPIO_FUNC_SEL2 = (0x01 << ((44-16*2)*2));
gpio_pad_dir_set( 1ULL << 44 );
set_power(0x0f); /* 0dbm */
chan = 0;
set_channel(chan); /* channel 11 */
*MACA_MACPANID = 0xaaaa;
*MACA_MAC16ADDR = 0x1111;
*MACA_TXACKDELAY = 68; /* 68 puts the tx ack at about the correct spot */
set_prm_mode(AUTOACK);
print_welcome("rftest-rx");
while(1) {
/* call check_maca() periodically --- this works around */
/* a few lockup conditions */
check_maca();
if((p = rx_packet())) {
/* print and free the packet */
printf("autoack-rx --- ");
print_packet(p);
maca_free_packet(p);
}
if(uart1_can_get()) {
c = uart1_getc();
if(c == 'z') t++;
if(c == 'x') t--;
*MACA_TXACKDELAY = t;
printf("tx ack delay: %d\n\r", t);
}
}
}
// read len bytes from serial
void readData(byte *bData, int len)
{
while (len-- > 0)
{
*bData = uart1_getc();
bData++;
}
}
//Hilfsfunktion:
void flushdata(void)
{
uint8_t blank = 0;
for(uint8_t i = 0; i < 20; i++)
{
blank = uart1_getc();
}
}
// Get a string from the ring buffer.
// If bytes are in the buffer, the receive function will run as long
// as the buffer is not empty.
void receiveStringUART ( char* inputString, uint8_t stringSize )
{
// Received character and error bitmask.
unsigned int inputChar;
// Get a character from the ring buffer.
// Do this in a loop as long as new data is in the buffer.
for(uint8_t charIndex = 0; charIndex<stringSize-1; charIndex++)
{
// Get byte from the buffer.
// uart_getc returns the data byte and an error code.
inputChar = uart1_getc();
// Evaluate the error code to see if any data was passed.
// If no data was passed...
if ( inputChar & UART_NO_DATA )
{
//... append end of string character.
// This will also clear the input string if nothing was received.
inputString[charIndex] = '\0';
// Exit the loop.
break;
}
// Evaluate error codes.
// In case of frame error...
else if ( inputChar & UART_FRAME_ERROR )
{
//... send back error message.
uart1_puts_P("UART Frame Error: ");
}
// In case of overrun error...
else if ( inputChar & UART_OVERRUN_ERROR )
{
//... send back error message.
// Overrun, a character already present in the UART UDR register was
// not read by the interrupt handler before the next character arrived,
// one or more received characters have been dropped
uart1_puts_P("UART Overrun Error: ");
}
// In case of buffer overflow...
else if ( inputChar & UART_BUFFER_OVERFLOW )
{
//... send back error message.
uart1_puts_P("Buffer overflow error: ");
// We are not reading the receive buffer fast enough,
// one or more received character have been dropped
}
// Finally, assemble the character to a string.
inputString[charIndex] = inputChar;
}
// Return the pointer to the received string.
// return inputString;
}
void main(void) {
uart1_init(INC,MOD,SAMP);
while(1) {
if(uart1_can_get()) {
/* Receive buffer isn't empty */
/* read a byte and write it to the transmit buffer */
uart1_putc(uart1_getc());
}
}
}
int main(void)
{
int x = 32768;
trim_xtal();
uart_init(UART1, 115200);
rtc_init();
printf("pwm test\r\n");
pwm_init_stopped(TMR0, 12000000, x);
pwm_init_stopped(TMR1, 12000000, x);
TMR0->ENBL |= TMR_ENABLE_BIT(TMR0) | TMR_ENABLE_BIT(TMR1);
for(;;) {
printf("duty %d = %d%%\r\n", x, ((x * 100 + 32768) / 65536));
switch(uart1_getc()) {
case '[': x -= 1; break;
case ']': x += 1; break;
case '-': x -= 32; break;
case '=': x += 32; break;
case '_': x -= 512; break;
case '+': x += 512; break;
case '`': x = 65535 * 0/10; break;
case '1': x = 65535 * 1/10; break;
case '2': x = 65535 * 2/10; break;
case '3': x = 65535 * 3/10; break;
case '4': x = 65535 * 4/10; break;
case '5': x = 65535 * 5/10; break;
case '6': x = 65535 * 6/10; break;
case '7': x = 65535 * 7/10; break;
case '8': x = 65535 * 8/10; break;
case '9': x = 65535 * 9/10; break;
case '0': x = 65535 * 10/10; break;
}
x &= 65535;
pwm_duty(TMR0, x);
}
}
void main(void) {
volatile packet_t *p;
char c;
uint16_t r=30; /* start reception 100us before ack should arrive */
uint16_t end=180; /* 750 us receive window*/
/* trim the reference osc. to 24MHz */
trim_xtal();
uart_init(UART1, 115200);
vreg_init();
maca_init();
set_channel(0); /* channel 11 */
// set_power(0x0f); /* 0xf = -1dbm, see 3-22 */
// set_power(0x11); /* 0x11 = 3dbm, see 3-22 */
set_power(0x12); /* 0x12 is the highest, not documented */
/* sets up tx_on, should be a board specific item */
GPIO->FUNC_SEL_44 = 1;
GPIO->PAD_DIR_SET_44 = 1;
GPIO->FUNC_SEL_45 = 2;
GPIO->PAD_DIR_SET_45 = 1;
*MACA_RXACKDELAY = r;
printf("rx warmup: %d\n\r", (int)(*MACA_WARMUP & 0xfff));
*MACA_RXEND = end;
printf("rx end: %d\n\r", (int)(*MACA_RXEND & 0xfff));
set_prm_mode(AUTOACK);
print_welcome("rftest-tx");
while(1) {
/* call check_maca() periodically --- this works around */
/* a few lockup conditions */
check_maca();
while((p = rx_packet())) {
if(p) {
printf("RX: ");
print_packet(p);
free_packet(p);
}
}
if(uart1_can_get()) {
c = uart1_getc();
switch(c) {
case 'z':
r++;
if(r > 4095) { r = 0; }
*MACA_RXACKDELAY = r;
printf("rx ack delay: %d\n\r", r);
break;
case 'x':
if(r == 0) { r = 4095; } else { r--; }
*MACA_RXACKDELAY = r;
printf("rx ack delay: %d\n\r", r);
break;
case 'q':
end++;
if(r > 4095) { r = 0; }
*MACA_RXEND = end;
printf("rx end: %d\n\r", end);
break;
case 'w':
end--;
if(r == 0) { r = 4095; } else { r--; }
*MACA_RXEND = end;
printf("rx end: %d\n\r", end);
break;
default:
p = get_free_packet();
if(p) {
fill_packet(p);
printf("autoack-tx --- ");
print_packet(p);
tx_packet(p);
}
break;
}
}
}
}
void check_wlan_cmd()
{
static unsigned char cmdstate = WLANCMD_NONE; // Status des aktuellen Befehls
static unsigned char cindex = 0; // Position in wlan_string (global)
unsigned int c; // zum Verarbeiten des aktuellen Zeichens
unsigned char exit; // für while-Schleifen-Ausstieg
unsigned char uarterror; // UART Empfangsfehler
exit = 0;
while(!exit)
{
// uart0_getc() returns in the lower byte the received character and in the higher byte (bitmask) the last receive error
// UART_NO_DATA is returned when no data is available.
uarterror = 0;
//c = uart0_getc(); //
#if defined( WLAN_UART_NR ) // WLAN_UART_NR = 1
c = uart1_getc();
#else // WLAN_UART_NR = 0
c = uart0_getc();
#endif // WLAN_UART_NR
if ( c & UART_NO_DATA ) //no data available from UART
{
exit = 1;
}
else // data available
{
// new data available from UART - check for Frame or Overrun error
if ( c & UART_FRAME_ERROR )
{
// Framing Error detected, i.e no stop bit detected
uarterror = 1;
}
if ( c & UART_OVERRUN_ERROR )
{
// Overrun, a character already present in the UART UDR register was
// not read by the interrupt handler before the next character arrived,
// one or more received characters have been dropped
uarterror = 2;
}
if ( c & UART_BUFFER_OVERFLOW )
{
// We are not reading the receive buffer fast enough, one or more received character have been dropped
uarterror = 3;
}
// empfangenes Zeichen verarbeiten
if (!uarterror) // falls kein Fehler aufgetreten ist
{
char d = (char)c;
if (d == 60) // > Befehl beginnt
{
cmdstate = WLANCMD_STARTED; // ab nun Zeichen nach wlan_string übernehmen
cindex = 0;
memset(wlan_string, 0, UART_MAXSTRLEN+1);
}
else if (d == 62) // > abschließendes Zeichen wurde empfangen
{
if (cmdstate == WLANCMD_STARTED) { befehl_auswerten(); }
cmdstate = WLANCMD_NONE;
}
else
{
if (cmdstate == WLANCMD_STARTED) // Zeichen in Befehl übernehmen
{
if (cindex < UART_MAXSTRLEN)
{
wlan_string[cindex] = d;
cindex++;
}
else { cmdstate = WLANCMD_NONE; } // Befehl ist zu lange - muss ignoriert werden!
}
}
}
else { cmdstate = WLANCMD_NONE; } // bei uarterror bisherige Befehlsdaten verwerfen
}
} // end while loop
} //end check_wlan_cmd()
int main(void) {
mc1322x_init();
/* m12_init() flips the mux switch */
/* trims the main crystal load capacitance */
if (!FORCE_ECONOTAG_I && CRM->SYS_CNTLbits.XTAL32_EXISTS) {
/* M12 based econotag */
PRINTF("trim xtal for M12\n\r");
CRM->XTAL_CNTLbits.XTAL_CTUNE = (M12_CTUNE_4PF << 4) | M12_CTUNE;
CRM->XTAL_CNTLbits.XTAL_FTUNE = M12_FTUNE;
/* configure pullups for low power */
GPIO->FUNC_SEL.GPIO_63 = 3;
GPIO->PAD_PU_SEL.GPIO_63 = 0;
GPIO->FUNC_SEL.SS = 3;
GPIO->PAD_PU_SEL.SS = 1;
GPIO->FUNC_SEL.VREF2H = 3;
GPIO->PAD_PU_SEL.VREF2H = 1;
GPIO->FUNC_SEL.U1RTS = 3;
GPIO->PAD_PU_SEL.U1RTS = 1;
} else {
/* econotag I */
PRINTF("trim xtal for Econotag I\n\r");
CRM->XTAL_CNTLbits.XTAL_CTUNE = (ECONOTAG_CTUNE_4PF << 4) | ECONOTAG_CTUNE;
CRM->XTAL_CNTLbits.XTAL_FTUNE = ECONOTAG_FTUNE;
}
/* create mac address if blank*/
if (mc1322x_config.eui == 0) {
/* mac address is blank */
/* construct a new mac address based on IAB or OUI definitions */
/* if an M12_SERIAL number is not defined */
/* generate a random extension in the Redwire experimental IAB */
/* The Redwire IAB (for development only) is: */
/* OUI: 0x0050C2 IAB: 0xA8C */
/* plus a random 24-bit extension */
/* Otherwise, construct a mac based on the M12_SERIAL */
/* Owners of an Econotag I (not M12 based) can request a serial number from Redwire */
/* to use here */
/* M12 mac is of the form "EC473C4D12000000" */
/* Redwire's OUI: EC473C */
/* M12: 4D12 */
/* next six nibbles are the M12 serial number as hex */
/* e.g. if the barcode reads: "12440021" = BDD1D5 */
/* full mac is EC473C4D12BDD1D5 */
#if (M12_SERIAL == 0)
/* use random mac from experimental range */
mc1322x_config.eui = (0x0050C2A8Cull << 24) | (*MACA_RANDOM & (0xffffff));
#else
/* construct mac from serial number */
mc1322x_config.eui = (0xEC473C4D12ull << 24) | M12_SERIAL;
#endif
mc1322x_config_save(&mc1322x_config);
}
/* configure address on maca hardware and RIME */
contiki_maca_set_mac_address(mc1322x_config.eui);
#if NETSTACK_CONF_WITH_IPV6
memcpy(&uip_lladdr.addr, &linkaddr_node_addr.u8, sizeof(uip_lladdr.addr));
queuebuf_init();
NETSTACK_RDC.init();
NETSTACK_MAC.init();
NETSTACK_NETWORK.init();
#if DEBUG_ANNOTATE
print_netstack();
#endif
#if ! SLIP_RADIO
process_start(&tcpip_process, NULL);
#endif
#if DEBUG_ANNOTATE
print_lladdrs();
#endif
#endif /* endif NETSTACK_CONF_WITH_IPV6 */
process_start(&sensors_process, NULL);
print_processes(autostart_processes);
autostart_start(autostart_processes);
/* Main scheduler loop */
while(1) {
check_maca();
if(uart1_input_handler != NULL) {
if(uart1_can_get()) {
uart1_input_handler(uart1_getc());
}
}
process_run();
}
return 0;
}
uint8_t um6_rwc(uint8_t um6_register, uint8_t batch, uint8_t r_w_c, uint16_t um6_result[], uint8_t data_size)
{
uint8_t checksum0 = 0;
uint8_t checksum1 = 0;
uint16_t checksum = 0;
uint8_t pt_is_batch = 0;
if(batch > 0)
{
pt_is_batch = PT_IS_BATCH;
}
if(r_w_c == UM6_DATA_READ)
checksum = ('s'+'n'+'p' + (pt_is_batch | batch) + um6_register);
else if(r_w_c == UM6_DATA_WRITE)
checksum = ('s'+'n'+'p' + (PT_HAS_DATA | pt_is_batch | batch) + um6_register);
else if(r_w_c == UM6_DATA_CMD)
checksum = ('s'+'n'+'p' + um6_register);
checksum1 = checksum >> 8;
checksum0 = checksum & 0xff;
uart1_putc('s');
uart1_putc('n');
uart1_putc('p');
if(r_w_c == UM6_DATA_READ)
uart1_putc(pt_is_batch | batch); //PT
else if(r_w_c == UM6_DATA_WRITE)
uart1_putc(PT_HAS_DATA | pt_is_batch | batch);
else //if(r_w_c == UM6_DATA_CMD)
uart1_putc(0);
uart1_putc(um6_register); //ADR
uart1_putc(checksum1); //Checksum1
uart1_putc(checksum0); //Checksum1
uint8_t data[8] = {0};
uint16_t data_sum = 0;
//if((r_w_c == UM6_DATA_CMD) || (r_w_c == UM6_DATA_WRITE))
// _delay_ms(25); //UM6 braucht dann etwas Zeit zum Antworten
uint8_t new_dat = uart1_getc();
if(new_dat & UART_NO_DATA)
{
//no data
return 7;
}
else if(new_dat == 's')
{
if(uart1_getc() == 'n')
{
if(uart1_getc() == 'p')
{
uint8_t r_w_c_batch = uart1_getc();
if( ((r_w_c_batch == (PT_HAS_DATA | pt_is_batch | batch)) && (r_w_c == UM6_DATA_READ)) ||
((r_w_c_batch == 0) && (r_w_c == UM6_DATA_WRITE)) || //== 0 wegen COMMAND_COMPLETE
((r_w_c_batch == 0) && (r_w_c == UM6_DATA_CMD)))
{
if(uart1_getc() == um6_register)
{
uint8_t i_stop = 0;
if(batch > 0)
{
i_stop = batch;
}
else
{
i_stop = 4; //1 Register
}
for(uint8_t i = 0; i<i_stop; i++)
{
data[i] = uart1_getc();
data_sum += data[i];
}
checksum1 = uart1_getc();
checksum0 = uart1_getc();
checksum = ((checksum1 << 8) | checksum0);
if( ((checksum == ('s' + 'n' + 'p' + (PT_HAS_DATA | pt_is_batch | batch) + um6_register + data_sum)) && (r_w_c == UM6_DATA_READ)) ||
((checksum == 0) && (r_w_c == UM6_DATA_WRITE)) ||
((checksum == 0) && (r_w_c == UM6_DATA_CMD)))
{
for(uint8_t i = 0; i < data_size; i++)
{
um6_result[i] = (data[(i*2)+1] | (data[(i*2)]<<8));
}
return 0;
}
else
{
flushdata();
return 1;
}
}
else
{
flushdata();
return 2;
}
}
else
{
flushdata();
return 3;
}
}
else
{
flushdata();
return 4;
}
}
else
{
flushdata();
return 5;
}
}
else
{
flushdata();
return 6;
}
}
int main(void) {
nvmType_t type=0;
nvmErr_t err;
volatile uint8_t c;
volatile uint32_t i;
volatile uint32_t buf[4];
volatile uint32_t len=0;
volatile uint32_t state = SCAN_X;
volatile uint32_t addr,data;
uart_init(UART1, 115200);
disable_irq(UART1);
vreg_init();
dbg_putstr("Detecting internal nvm\n\r");
err = nvm_detect(gNvmInternalInterface_c, &type);
dbg_putstr("nvm_detect returned: 0x");
dbg_put_hex(err);
dbg_putstr(" type is: 0x");
dbg_put_hex32(type);
dbg_putstr("\n\r");
err = nvm_read(gNvmInternalInterface_c, type, (uint8_t *)nvm_base, NVM_BASE, 0x100);
dbg_putstr("nvm_read returned: 0x");
dbg_put_hex(err);
dbg_putstr("\n\r");
/* erase the flash */
nvm_setsvar(0);
err = nvm_erase(gNvmInternalInterface_c, type, 0x40000000);
dbg_putstr("nvm_erase returned: 0x");
dbg_put_hex(err);
dbg_putstr("\n\r");
dbg_putstr(" type is: 0x");
dbg_put_hex32(type);
dbg_putstr("\n\r");
err = nvm_write(gNvmInternalInterface_c, type, (uint8_t *)nvm_base, NVM_BASE, 0x100);
dbg_putstr("nvm_write returned: 0x");
dbg_put_hex(err);
dbg_putstr("\n\r");
/* say we are ready */
len = 0;
putstr("ready");
flushrx();
/* read the length */
for(i=0; i<4; i++) {
c = uart1_getc();
/* bail if the first byte of the length is zero */
len += (c<<(i*8));
}
dbg_putstr("len: ");
dbg_put_hex32(len);
dbg_putstr("\n\r");
dbg_putstr(" type is: 0x");
dbg_put_hex32(type);
dbg_putstr("\n\r");
putstr("flasher done\n\r");
state = SCAN_X; addr=0;
while((c=getc())) {
if(state == SCAN_X) {
/* read until we see an 'x' */
if(c==0) { break; }
if(c!='x'){ continue; }
/* go to read_chars once we have an 'x' */
state = READ_CHARS;
i = 0;
}
if(state == READ_CHARS) {
/* read all the chars up to a ',' */
((uint8_t *)buf)[i++] = c;
/* after reading a ',' */
/* goto PROCESS state */
if((c == ',') || (c == 0)) { state = PROCESS; }
}
if(state == PROCESS) {
if(addr==0) {
/*interpret the string as the starting address */
addr = to_u32(buf);
} else {
/* string is data to write */
data = to_u32(buf);
putstr("writing addr ");
put_hex32(NVM_BASE+addr);
putstr(" data ");
put_hex32(data);
err = nvm_write(gNvmInternalInterface_c, type, (uint8_t *)&data, NVM_BASE+addr, 4);
addr += 4;
putstr(" err ");
put_hex32(err);
putstr("\n\r");
}
/* look for the next 'x' */
state=SCAN_X;
}
}
putstr("process flasher done\n\r");
while(1) {continue;};
}
void main(void) {
nvmType_t type=0;
nvmErr_t err;
volatile uint8_t c;
volatile uint32_t i;
volatile uint32_t buf[4];
volatile uint32_t len=0;
volatile uint32_t state = SCAN_X;
volatile uint32_t addr,data;
uart_init(INC, MOD, SAMP);
disable_irq(UART1);
vreg_init();
dbg_putstr("Detecting internal nvm\n\r");
err = nvm_detect(gNvmInternalInterface_c, &type);
dbg_putstr("nvm_detect returned: 0x");
dbg_put_hex(err);
dbg_putstr(" type is: 0x");
dbg_put_hex32(type);
dbg_putstr("\n\r");
/* erase the flash */
err = nvm_erase(gNvmInternalInterface_c, type, 0x7fffffff);
dbg_putstr("nvm_erase returned: 0x");
dbg_put_hex(err);
dbg_putstr("\n\r");
dbg_putstr(" type is: 0x");
dbg_put_hex32(type);
dbg_putstr("\n\r");
/* say we are ready */
len = 0;
putstr("ready");
flushrx();
/* read the length */
for(i=0; i<4; i++) {
c = uart1_getc();
/* bail if the first byte of the length is zero */
len += (c<<(i*8));
}
dbg_putstr("len: ");
dbg_put_hex32(len);
dbg_putstr("\n\r");
/* write the OKOK magic */
#if BOOT_OK
((uint8_t *)buf)[0] = 'O'; ((uint8_t *)buf)[1] = 'K'; ((uint8_t *)buf)[2] = 'O'; ((uint8_t *)buf)[3] = 'K';
#elif BOOT_SECURE
((uint8_t *)buf)[0] = 'S'; ((uint8_t *)buf)[1] = 'E'; ((uint8_t *)buf)[2] = 'C'; ((uint8_t *)buf)[3] = 'U';
#else
((uint8_t *)buf)[0] = 'N'; ((uint8_t *)buf)[1] = 'O'; ((uint8_t *)buf)[2] = 'N'; ((uint8_t *)buf)[3] = 'O';
#endif
dbg_putstr(" type is: 0x");
dbg_put_hex32(type);
dbg_putstr("\n\r");
/* don't make a valid boot image if the received length is zero */
if(len == 0) {
((uint8_t *)buf)[0] = 'N';
((uint8_t *)buf)[1] = 'O';
((uint8_t *)buf)[2] = 'N';
((uint8_t *)buf)[3] = 'O';
}
err = nvm_write(gNvmInternalInterface_c, type, (uint8_t *)buf, 0, 4);
dbg_putstr("nvm_write returned: 0x");
dbg_put_hex(err);
dbg_putstr("\n\r");
/* write the length */
err = nvm_write(gNvmInternalInterface_c, type, (uint8_t *)&len, 4, 4);
/* read a byte, write a byte */
for(i=0; i<len; i++) {
c = getc();
err = nvm_write(gNvmInternalInterface_c, type, (uint8_t *)&c, 8+i, 1);
}
putstr("flasher done\n\r");
state = SCAN_X; addr=0;
while((c=getc())) {
if(state == SCAN_X) {
/* read until we see an 'x' */
if(c==0) { break; }
if(c!='x'){ continue; }
/* go to read_chars once we have an 'x' */
state = READ_CHARS;
i = 0;
}
if(state == READ_CHARS) {
/* read all the chars up to a ',' */
((uint8_t *)buf)[i++] = c;
/* after reading a ',' */
/* goto PROCESS state */
if((c == ',') || (c == 0)) { state = PROCESS; }
}
if(state == PROCESS) {
if(addr==0) {
/*interpret the string as the starting address */
addr = to_u32(buf);
} else {
/* string is data to write */
data = to_u32(buf);
putstr("writing addr ");
put_hex32(addr);
putstr(" data ");
put_hex32(data);
putstr("\n\r");
err = nvm_write(gNvmInternalInterface_c, 1, (uint8_t *)&data, addr, 4);
addr += 4;
}
/* look for the next 'x' */
state=SCAN_X;
}
}
while(1) {continue;};
}