BlockMultiModeBacksideAutopilot::~BlockMultiModeBacksideAutopilot()
{
// send one last publication when destroyed, setting
// all output to zero
for (unsigned i = 0; i < NUM_ACTUATOR_CONTROLS; i++)
_actuators.control[i] = 0.0f;
updatePublications();
}
void BlockSegwayController::update() {
// wait for a sensor update, check for exit condition every 100 ms
if (poll(&_attPoll, 1, 100) < 0) return; // poll error
uint64_t newTimeStamp = hrt_absolute_time();
float dt = (newTimeStamp - _timeStamp) / 1.0e6f;
_timeStamp = newTimeStamp;
// check for sane values of dt
// to prevent large control responses
if (dt > 1.0f || dt < 0) return;
// set dt for all child blocks
setDt(dt);
// check for new updates
if (_param_update.updated()) updateParams();
// get new information from subscriptions
updateSubscriptions();
// default all output to zero unless handled by mode
for (unsigned i = 2; i < NUM_ACTUATOR_CONTROLS; i++)
_actuators.control[i] = 0.0f;
// only update guidance in auto mode
if (_status.main_state == MAIN_STATE_AUTO) {
// update guidance
}
// compute speed command
float spdCmd = -th2v.update(_att.pitch) - q2v.update(_att.pitchspeed);
// handle autopilot modes
if (_status.main_state == MAIN_STATE_AUTO ||
_status.main_state == MAIN_STATE_ALTCTL ||
_status.main_state == MAIN_STATE_POSCTL) {
_actuators.control[0] = spdCmd;
_actuators.control[1] = spdCmd;
} else if (_status.main_state == MAIN_STATE_MANUAL) {
if (_status.navigation_state == NAVIGATION_STATE_DIRECT) {
_actuators.control[CH_LEFT] = _manual.throttle;
_actuators.control[CH_RIGHT] = _manual.pitch;
} else if (_status.navigation_state == NAVIGATION_STATE_STABILIZE) {
_actuators.control[0] = spdCmd;
_actuators.control[1] = spdCmd;
}
}
// update all publications
updatePublications();
}
void BlockMultiModeBacksideAutopilot::update()
{
// wait for a sensor update, check for exit condition every 100 ms
if (poll(&_attPoll, 1, 100) < 0) return; // poll error
uint64_t newTimeStamp = hrt_absolute_time();
float dt = (newTimeStamp - _timeStamp) / 1.0e6f;
_timeStamp = newTimeStamp;
// check for sane values of dt
// to prevent large control responses
if (dt > 1.0f || dt < 0) return;
// set dt for all child blocks
setDt(dt);
// store old position command before update if new command sent
if (_posCmd.updated()) {
_lastPosCmd = _posCmd.getData();
}
// check for new updates
if (_param_update.updated()) updateParams();
// get new information from subscriptions
updateSubscriptions();
// default all output to zero unless handled by mode
for (unsigned i = 4; i < NUM_ACTUATOR_CONTROLS; i++)
_actuators.control[i] = 0.0f;
// only update guidance in auto mode
if (_status.state_machine == SYSTEM_STATE_AUTO) {
// update guidance
_guide.update(_pos, _att, _posCmd, _lastPosCmd);
}
// XXX handle STABILIZED (loiter on spot) as well
// once the system switches from manual or auto to stabilized
// the setpoint should update to loitering around this position
// handle autopilot modes
if (_status.state_machine == SYSTEM_STATE_AUTO ||
_status.state_machine == SYSTEM_STATE_STABILIZED) {
// update guidance
_guide.update(_pos, _att, _posCmd, _lastPosCmd);
// calculate velocity, XXX should be airspeed, but using ground speed for now
float v = sqrtf(_pos.vx * _pos.vx + _pos.vy * _pos.vy + _pos.vz * _pos.vz);
// altitude hold
float dThrottle = _h2Thr.update(_posCmd.altitude - _pos.alt);
// heading hold
float psiError = _wrap_pi(_guide.getPsiCmd() - _att.yaw);
float phiCmd = _phiLimit.update(_psi2Phi.update(psiError));
float pCmd = _phi2P.update(phiCmd - _att.roll);
// velocity hold
// negative sign because nose over to increase speed
float thetaCmd = _theLimit.update(-_v2Theta.update(
_vLimit.update(_vCmd.get()) - v));
float qCmd = _theta2Q.update(thetaCmd - _att.pitch);
// yaw rate cmd
float rCmd = 0;
// stabilization
_stabilization.update(pCmd, qCmd, rCmd,
_att.rollspeed, _att.pitchspeed, _att.yawspeed);
// output
_actuators.control[CH_AIL] = _stabilization.getAileron() + _trimAil.get();
_actuators.control[CH_ELV] = _stabilization.getElevator() + _trimElv.get();
_actuators.control[CH_RDR] = _stabilization.getRudder() + _trimRdr.get();
_actuators.control[CH_THR] = dThrottle + _trimThr.get();
// XXX limit throttle to manual setting (safety) for now.
// If it turns out to be confusing, it can be removed later once
// a first binary release can be targeted.
// This is not a hack, but a design choice.
/* do not limit in HIL */
if (!_status.flag_hil_enabled) {
/* limit to value of manual throttle */
_actuators.control[CH_THR] = (_actuators.control[CH_THR] < _manual.throttle) ?
_actuators.control[CH_THR] : _manual.throttle;
}
} else if (_status.state_machine == SYSTEM_STATE_MANUAL) {
if (_status.manual_control_mode == VEHICLE_MANUAL_CONTROL_MODE_DIRECT) {
_actuators.control[CH_AIL] = _manual.roll;
_actuators.control[CH_ELV] = _manual.pitch;
_actuators.control[CH_RDR] = _manual.yaw;
_actuators.control[CH_THR] = _manual.throttle;
} else if (_status.manual_control_mode == VEHICLE_MANUAL_CONTROL_MODE_SAS) {
// calculate velocity, XXX should be airspeed, but using ground speed for now
float v = sqrtf(_pos.vx * _pos.vx + _pos.vy * _pos.vy + _pos.vz * _pos.vz);
// pitch channel -> rate of climb
// TODO, might want to put a gain on this, otherwise commanding
// from +1 -> -1 m/s for rate of climb
//float dThrottle = _roc2Thr.update(
//_rocMax.get()*_manual.pitch - _pos.vz);
// roll channel -> bank angle
float phiCmd = _phiLimit.update(_manual.roll * _phiLimit.getMax());
float pCmd = _phi2P.update(phiCmd - _att.roll);
// throttle channel -> velocity
// negative sign because nose over to increase speed
float vCmd = _manual.throttle * (_vLimit.getMax() - _vLimit.getMin()) + _vLimit.getMin();
float thetaCmd = _theLimit.update(-_v2Theta.update(_vLimit.update(vCmd) - v));
float qCmd = _theta2Q.update(thetaCmd - _att.pitch);
// yaw rate cmd
float rCmd = 0;
// stabilization
_stabilization.update(pCmd, qCmd, rCmd,
_att.rollspeed, _att.pitchspeed, _att.yawspeed);
// output
_actuators.control[CH_AIL] = _stabilization.getAileron() + _trimAil.get();
_actuators.control[CH_ELV] = _stabilization.getElevator() + _trimElv.get();
_actuators.control[CH_RDR] = _stabilization.getRudder() + _trimRdr.get();
// currenlty using manual throttle
// XXX if you enable this watch out, vz might be very noisy
//_actuators.control[CH_THR] = dThrottle + _trimThr.get();
_actuators.control[CH_THR] = _manual.throttle;
// XXX limit throttle to manual setting (safety) for now.
// If it turns out to be confusing, it can be removed later once
// a first binary release can be targeted.
// This is not a hack, but a design choice.
/* do not limit in HIL */
if (!_status.flag_hil_enabled) {
/* limit to value of manual throttle */
_actuators.control[CH_THR] = (_actuators.control[CH_THR] < _manual.throttle) ?
_actuators.control[CH_THR] : _manual.throttle;
}
}
// body rates controller, disabled for now
else if (0 /*_status.manual_control_mode == VEHICLE_MANUAL_CONTROL_MODE_SAS*/) {
_stabilization.update(_manual.roll, _manual.pitch, _manual.yaw,
_att.rollspeed, _att.pitchspeed, _att.yawspeed);
_actuators.control[CH_AIL] = _stabilization.getAileron();
_actuators.control[CH_ELV] = _stabilization.getElevator();
_actuators.control[CH_RDR] = _stabilization.getRudder();
_actuators.control[CH_THR] = _manual.throttle;
}
}
// update all publications
updatePublications();
}
void BlockMultiModeBacksideAutopilot::update()
{
// wait for a sensor update, check for exit condition every 100 ms
if (poll(&_attPoll, 1, 100) < 0) return; // poll error
uint64_t newTimeStamp = hrt_absolute_time();
float dt = (newTimeStamp - _timeStamp) / 1.0e6f;
_timeStamp = newTimeStamp;
// check for sane values of dt
// to prevent large control responses
if (dt > 1.0f || dt < 0) return;
// set dt for all child blocks
setDt(dt);
// store old position command before update if new command sent
if (_posCmd.updated()) {
_lastPosCmd = _posCmd.getData();
}
// check for new updates
if (_param_update.updated()) updateParams();
// get new information from subscriptions
updateSubscriptions();
// default all output to zero unless handled by mode
for (unsigned i = 4; i < NUM_ACTUATOR_CONTROLS; i++)
_actuators.control[i] = 0.0f;
// handle autopilot modes
if (_status.state_machine == SYSTEM_STATE_STABILIZED) {
_stabilization.update(
_ratesCmd.roll, _ratesCmd.pitch, _ratesCmd.yaw,
_att.rollspeed, _att.pitchspeed, _att.yawspeed);
_actuators.control[CH_AIL] = _stabilization.getAileron();
_actuators.control[CH_ELV] = _stabilization.getElevator();
_actuators.control[CH_RDR] = _stabilization.getRudder();
_actuators.control[CH_THR] = _manual.throttle;
} else if (_status.state_machine == SYSTEM_STATE_AUTO) {
// update guidance
_guide.update(_pos, _att, _posCmd, _lastPosCmd);
// calculate velocity, XXX should be airspeed, but using ground speed for now
float v = sqrtf(_pos.vx * _pos.vx + _pos.vy * _pos.vy + _pos.vz * _pos.vz);
// commands
float rCmd = 0;
_backsideAutopilot.update(
_posCmd.altitude, _vCmd.get(), rCmd, _guide.getPsiCmd(),
_pos.alt, v,
_att.roll, _att.pitch, _att.yaw,
_att.rollspeed, _att.pitchspeed, _att.yawspeed
);
_actuators.control[CH_AIL] = _backsideAutopilot.getAileron();
_actuators.control[CH_ELV] = _backsideAutopilot.getElevator();
_actuators.control[CH_RDR] = _backsideAutopilot.getRudder();
_actuators.control[CH_THR] = _backsideAutopilot.getThrottle();
} else if (_status.state_machine == SYSTEM_STATE_MANUAL) {
_actuators.control[CH_AIL] = _manual.roll;
_actuators.control[CH_ELV] = _manual.pitch;
_actuators.control[CH_RDR] = _manual.yaw;
_actuators.control[CH_THR] = _manual.throttle;
}
// update all publications
updatePublications();
}
