static int ohci_quirk_amd700(struct usb_hcd *hcd)
{
struct ohci_hcd *ohci = hcd_to_ohci(hcd);
struct pci_dev *amd_smbus_dev;
u8 rev;
if (usb_amd_find_chipset_info())
ohci->flags |= OHCI_QUIRK_AMD_PLL;
amd_smbus_dev = pci_get_device(PCI_VENDOR_ID_ATI,
PCI_DEVICE_ID_ATI_SBX00_SMBUS, NULL);
if (!amd_smbus_dev)
return 0;
rev = amd_smbus_dev->revision;
/* SB800 needs pre-fetch fix */
if ((rev >= 0x40) && (rev <= 0x4f)) {
ohci->flags |= OHCI_QUIRK_AMD_PREFETCH;
ohci_dbg(ohci, "enabled AMD prefetch quirk\n");
}
pci_dev_put(amd_smbus_dev);
amd_smbus_dev = NULL;
return 0;
}
static void xhci_pci_quirks(struct device *dev, struct xhci_hcd *xhci)
{
struct pci_dev *pdev = to_pci_dev(dev);
/* Look for vendor-specific quirks */
if (pdev->vendor == PCI_VENDOR_ID_FRESCO_LOGIC &&
(pdev->device == PCI_DEVICE_ID_FRESCO_LOGIC_PDK ||
pdev->device == PCI_DEVICE_ID_FRESCO_LOGIC_FL1400)) {
if (pdev->device == PCI_DEVICE_ID_FRESCO_LOGIC_PDK &&
pdev->revision == 0x0) {
xhci->quirks |= XHCI_RESET_EP_QUIRK;
xhci_dbg(xhci, "QUIRK: Fresco Logic xHC needs configure"
" endpoint cmd after reset endpoint\n");
}
/* Fresco Logic confirms: all revisions of this chip do not
* support MSI, even though some of them claim to in their PCI
* capabilities.
*/
xhci->quirks |= XHCI_BROKEN_MSI;
xhci_dbg(xhci, "QUIRK: Fresco Logic revision %u "
"has broken MSI implementation\n",
pdev->revision);
xhci->quirks |= XHCI_TRUST_TX_LENGTH;
}
if (pdev->vendor == PCI_VENDOR_ID_NEC)
xhci->quirks |= XHCI_NEC_HOST;
if (pdev->vendor == PCI_VENDOR_ID_AMD && xhci->hci_version == 0x96)
xhci->quirks |= XHCI_AMD_0x96_HOST;
/* AMD PLL quirk */
if (pdev->vendor == PCI_VENDOR_ID_AMD && usb_amd_find_chipset_info())
xhci->quirks |= XHCI_AMD_PLL_FIX;
if (pdev->vendor == PCI_VENDOR_ID_INTEL &&
pdev->device == PCI_DEVICE_ID_INTEL_PANTHERPOINT_XHCI) {
xhci->quirks |= XHCI_SPURIOUS_SUCCESS;
xhci->quirks |= XHCI_EP_LIMIT_QUIRK;
xhci->limit_active_eps = 64;
xhci->quirks |= XHCI_SW_BW_CHECKING;
/*
* PPT desktop boards DH77EB and DH77DF will power back on after
* a few seconds of being shutdown. The fix for this is to
* switch the ports from xHCI to EHCI on shutdown. We can't use
* DMI information to find those particular boards (since each
* vendor will change the board name), so we have to key off all
* PPT chipsets.
*/
xhci->quirks |= XHCI_SPURIOUS_REBOOT;
xhci->quirks |= XHCI_AVOID_BEI;
}
if (pdev->vendor == PCI_VENDOR_ID_ETRON &&
pdev->device == PCI_DEVICE_ID_ASROCK_P67) {
xhci->quirks |= XHCI_RESET_ON_RESUME;
xhci_dbg(xhci, "QUIRK: Resetting on resume\n");
xhci->quirks |= XHCI_TRUST_TX_LENGTH;
}
if (pdev->vendor == PCI_VENDOR_ID_VIA)
xhci->quirks |= XHCI_RESET_ON_RESUME;
}
int usb_hcd_amd_remote_wakeup_quirk(struct pci_dev *pdev)
{
/* Make sure amd chipset type has already been initialized */
usb_amd_find_chipset_info();
if (amd_chipset.sb_type.gen != AMD_CHIPSET_YANGTZE)
return 0;
dev_dbg(&pdev->dev, "QUIRK: Enable AMD remote wakeup fix\n");
return 1;
}
bool usb_amd_hang_symptom_quirk(void)
{
u8 rev;
usb_amd_find_chipset_info();
rev = amd_chipset.sb_type.rev;
/* SB600 and old version of SB700 have hang symptom bug */
return amd_chipset.sb_type.gen == AMD_CHIPSET_SB600 ||
(amd_chipset.sb_type.gen == AMD_CHIPSET_SB700 &&
rev >= 0x3a && rev <= 0x3b);
}
static void xhci_pci_quirks(struct device *dev, struct xhci_hcd *xhci)
{
struct pci_dev *pdev = to_pci_dev(dev);
/* Look for vendor-specific quirks */
if (pdev->vendor == PCI_VENDOR_ID_FRESCO_LOGIC &&
pdev->device == PCI_DEVICE_ID_FRESCO_LOGIC_PDK) {
if (pdev->revision == 0x0) {
xhci->quirks |= XHCI_RESET_EP_QUIRK;
xhci_dbg(xhci, "QUIRK: Fresco Logic xHC needs configure"
" endpoint cmd after reset endpoint\n");
}
/* Fresco Logic confirms: all revisions of this chip do not
* support MSI, even though some of them claim to in their PCI
* capabilities.
*/
xhci->quirks |= XHCI_BROKEN_MSI;
xhci_dbg(xhci, "QUIRK: Fresco Logic revision %u "
"has broken MSI implementation\n",
pdev->revision);
}
if (pdev->vendor == PCI_VENDOR_ID_NEC)
xhci->quirks |= XHCI_NEC_HOST;
if (pdev->vendor == PCI_VENDOR_ID_AMD && xhci->hci_version == 0x96)
xhci->quirks |= XHCI_AMD_0x96_HOST;
/* AMD PLL quirk */
if (pdev->vendor == PCI_VENDOR_ID_AMD && usb_amd_find_chipset_info())
xhci->quirks |= XHCI_AMD_PLL_FIX;
if (pdev->vendor == PCI_VENDOR_ID_INTEL &&
pdev->device == PCI_DEVICE_ID_INTEL_PANTHERPOINT_XHCI) {
xhci->quirks |= XHCI_SPURIOUS_SUCCESS;
xhci->quirks |= XHCI_EP_LIMIT_QUIRK;
xhci->limit_active_eps = 64;
xhci->quirks |= XHCI_SW_BW_CHECKING;
}
#ifdef MY_ABC_HERE
xhci_vendor = pdev->vendor;
#endif
if (pdev->vendor == PCI_VENDOR_ID_ETRON &&
pdev->device == PCI_DEVICE_ID_ASROCK_P67) {
#ifdef MY_ABC_HERE
xhci_err(xhci, "Etron chip found.\n");
#endif
xhci->quirks |= XHCI_RESET_ON_RESUME;
xhci_dbg(xhci, "QUIRK: Resetting on resume\n");
}
}
static void xhci_pci_quirks(struct device *dev, struct xhci_hcd *xhci)
{
struct pci_dev *pdev = to_pci_dev(dev);
/* Look for vendor-specific quirks */
if (pdev->vendor == PCI_VENDOR_ID_FRESCO_LOGIC &&
pdev->device == PCI_DEVICE_ID_FRESCO_LOGIC_PDK) {
if (pdev->revision == 0x0) {
xhci->quirks |= XHCI_RESET_EP_QUIRK;
xhci_dbg(xhci, "QUIRK: Fresco Logic xHC needs configure"
" endpoint cmd after reset endpoint\n");
}
/* Fresco Logic confirms: all revisions of this chip do not
* support MSI, even though some of them claim to in their PCI
* capabilities.
*/
xhci->quirks |= XHCI_BROKEN_MSI;
xhci_dbg(xhci, "QUIRK: Fresco Logic revision %u "
"has broken MSI implementation\n",
pdev->revision);
}
if (pdev->vendor == PCI_VENDOR_ID_NEC)
xhci->quirks |= XHCI_NEC_HOST;
if (pdev->vendor == PCI_VENDOR_ID_AMD && xhci->hci_version == 0x96)
xhci->quirks |= XHCI_AMD_0x96_HOST;
/* AMD PLL quirk */
if (pdev->vendor == PCI_VENDOR_ID_AMD && usb_amd_find_chipset_info())
xhci->quirks |= XHCI_AMD_PLL_FIX;
if (pdev->vendor == PCI_VENDOR_ID_AMD)
xhci->quirks |= XHCI_TRUST_TX_LENGTH;
if (pdev->vendor == PCI_VENDOR_ID_INTEL)
xhci->quirks |= XHCI_AVOID_BEI;
if (pdev->vendor == PCI_VENDOR_ID_INTEL &&
(pdev->device == PCI_DEVICE_ID_INTEL_SUNRISEPOINT_LP_XHCI ||
pdev->device == PCI_DEVICE_ID_INTEL_SUNRISEPOINT_H_XHCI ||
pdev->device == PCI_DEVICE_ID_INTEL_CHERRYVIEW_XHCI)) {
xhci->quirks |= XHCI_PME_STUCK_QUIRK;
}
if (pdev->vendor == PCI_VENDOR_ID_ETRON &&
pdev->device == PCI_DEVICE_ID_ASROCK_P67) {
xhci->quirks |= XHCI_RESET_ON_RESUME;
xhci_dbg(xhci, "QUIRK: Resetting on resume\n");
}
if (pdev->vendor == PCI_VENDOR_ID_VIA)
xhci->quirks |= XHCI_RESET_ON_RESUME;
}
static int ohci_quirk_amd700(struct usb_hcd *hcd)
{
struct ohci_hcd *ohci = hcd_to_ohci(hcd);
if (usb_amd_find_chipset_info())
ohci->flags |= OHCI_QUIRK_AMD_PLL;
/* SB800 needs pre-fetch fix */
if (usb_amd_prefetch_quirk()) {
ohci->flags |= OHCI_QUIRK_AMD_PREFETCH;
ohci_dbg(ohci, "enabled AMD prefetch quirk\n");
}
return 0;
}
static void xhci_pci_quirks(struct device *dev, struct xhci_hcd *xhci)
{
struct pci_dev *pdev = to_pci_dev(dev);
/* Look for vendor-specific quirks */
if (pdev->vendor == PCI_VENDOR_ID_FRESCO_LOGIC &&
(pdev->device == PCI_DEVICE_ID_FRESCO_LOGIC_PDK ||
pdev->device == PCI_DEVICE_ID_FRESCO_LOGIC_FL1400)) {
if (pdev->device == PCI_DEVICE_ID_FRESCO_LOGIC_PDK &&
pdev->revision == 0x0) {
xhci->quirks |= XHCI_RESET_EP_QUIRK;
xhci_dbg_trace(xhci, trace_xhci_dbg_quirks,
"QUIRK: Fresco Logic xHC needs configure"
" endpoint cmd after reset endpoint");
}
if (pdev->device == PCI_DEVICE_ID_FRESCO_LOGIC_PDK &&
pdev->revision == 0x4) {
xhci->quirks |= XHCI_SLOW_SUSPEND;
xhci_dbg_trace(xhci, trace_xhci_dbg_quirks,
"QUIRK: Fresco Logic xHC revision %u"
"must be suspended extra slowly",
pdev->revision);
}
if (pdev->device == PCI_DEVICE_ID_FRESCO_LOGIC_PDK)
xhci->quirks |= XHCI_BROKEN_STREAMS;
/* Fresco Logic confirms: all revisions of this chip do not
* support MSI, even though some of them claim to in their PCI
* capabilities.
*/
xhci->quirks |= XHCI_BROKEN_MSI;
xhci_dbg_trace(xhci, trace_xhci_dbg_quirks,
"QUIRK: Fresco Logic revision %u "
"has broken MSI implementation",
pdev->revision);
xhci->quirks |= XHCI_TRUST_TX_LENGTH;
}
if (pdev->vendor == PCI_VENDOR_ID_FRESCO_LOGIC &&
pdev->device == PCI_DEVICE_ID_FRESCO_LOGIC_FL1009)
xhci->quirks |= XHCI_BROKEN_STREAMS;
if (pdev->vendor == PCI_VENDOR_ID_NEC)
xhci->quirks |= XHCI_NEC_HOST;
if (pdev->vendor == PCI_VENDOR_ID_AMD && xhci->hci_version == 0x96)
xhci->quirks |= XHCI_AMD_0x96_HOST;
/* AMD PLL quirk */
if (pdev->vendor == PCI_VENDOR_ID_AMD && usb_amd_find_chipset_info())
xhci->quirks |= XHCI_AMD_PLL_FIX;
if (pdev->vendor == PCI_VENDOR_ID_AMD)
xhci->quirks |= XHCI_TRUST_TX_LENGTH;
if (pdev->vendor == PCI_VENDOR_ID_INTEL) {
xhci->quirks |= XHCI_LPM_SUPPORT;
xhci->quirks |= XHCI_INTEL_HOST;
xhci->quirks |= XHCI_AVOID_BEI;
}
if (pdev->vendor == PCI_VENDOR_ID_INTEL &&
pdev->device == PCI_DEVICE_ID_INTEL_PANTHERPOINT_XHCI) {
xhci->quirks |= XHCI_EP_LIMIT_QUIRK;
xhci->limit_active_eps = 64;
xhci->quirks |= XHCI_SW_BW_CHECKING;
/*
* PPT desktop boards DH77EB and DH77DF will power back on after
* a few seconds of being shutdown. The fix for this is to
* switch the ports from xHCI to EHCI on shutdown. We can't use
* DMI information to find those particular boards (since each
* vendor will change the board name), so we have to key off all
* PPT chipsets.
*/
xhci->quirks |= XHCI_SPURIOUS_REBOOT;
}
if (pdev->vendor == PCI_VENDOR_ID_INTEL &&
(pdev->device == PCI_DEVICE_ID_INTEL_LYNXPOINT_LP_XHCI ||
pdev->device == PCI_DEVICE_ID_INTEL_WILDCATPOINT_LP_XHCI)) {
xhci->quirks |= XHCI_SPURIOUS_REBOOT;
xhci->quirks |= XHCI_SPURIOUS_WAKEUP;
}
if (pdev->vendor == PCI_VENDOR_ID_INTEL &&
(pdev->device == PCI_DEVICE_ID_INTEL_SUNRISEPOINT_LP_XHCI ||
pdev->device == PCI_DEVICE_ID_INTEL_SUNRISEPOINT_H_XHCI ||
pdev->device == PCI_DEVICE_ID_INTEL_CHERRYVIEW_XHCI ||
pdev->device == PCI_DEVICE_ID_INTEL_BROXTON_M_XHCI ||
pdev->device == PCI_DEVICE_ID_INTEL_BROXTON_B_XHCI ||
pdev->device == PCI_DEVICE_ID_INTEL_APL_XHCI)) {
xhci->quirks |= XHCI_PME_STUCK_QUIRK;
}
if (pdev->vendor == PCI_VENDOR_ID_INTEL &&
(pdev->device == PCI_DEVICE_ID_INTEL_CHERRYVIEW_XHCI ||
pdev->device == PCI_DEVICE_ID_INTEL_APL_XHCI))
xhci->quirks |= XHCI_MISSING_CAS;
if (pdev->vendor == PCI_VENDOR_ID_ETRON &&
pdev->device == PCI_DEVICE_ID_EJ168) {
xhci->quirks |= XHCI_RESET_ON_RESUME;
xhci->quirks |= XHCI_TRUST_TX_LENGTH;
xhci->quirks |= XHCI_BROKEN_STREAMS;
}
if (pdev->vendor == PCI_VENDOR_ID_RENESAS &&
pdev->device == 0x0015)
xhci->quirks |= XHCI_RESET_ON_RESUME;
if (pdev->vendor == PCI_VENDOR_ID_VIA)
xhci->quirks |= XHCI_RESET_ON_RESUME;
/* See https://bugzilla.kernel.org/show_bug.cgi?id=79511 */
if (pdev->vendor == PCI_VENDOR_ID_VIA &&
pdev->device == 0x3432)
xhci->quirks |= XHCI_BROKEN_STREAMS;
if (pdev->vendor == PCI_VENDOR_ID_ASMEDIA &&
pdev->device == 0x1042)
xhci->quirks |= XHCI_BROKEN_STREAMS;
if (xhci->quirks & XHCI_RESET_ON_RESUME)
xhci_dbg_trace(xhci, trace_xhci_dbg_quirks,
"QUIRK: Resetting on resume");
}
/* called during probe() after chip reset completes */
static int ehci_pci_setup(struct usb_hcd *hcd)
{
struct ehci_hcd *ehci = hcd_to_ehci(hcd);
struct pci_dev *pdev = to_pci_dev(hcd->self.controller);
struct pci_dev *p_smbus;
u8 rev;
u32 temp;
int retval;
switch (pdev->vendor) {
case PCI_VENDOR_ID_TOSHIBA_2:
/* celleb's companion chip */
if (pdev->device == 0x01b5) {
#ifdef CONFIG_USB_EHCI_BIG_ENDIAN_MMIO
ehci->big_endian_mmio = 1;
#else
ehci_warn(ehci,
"unsupported big endian Toshiba quirk\n");
#endif
}
break;
}
ehci->caps = hcd->regs;
ehci->regs = hcd->regs +
HC_LENGTH(ehci, ehci_readl(ehci, &ehci->caps->hc_capbase));
dbg_hcs_params(ehci, "reset");
dbg_hcc_params(ehci, "reset");
/* ehci_init() causes memory for DMA transfers to be
* allocated. Thus, any vendor-specific workarounds based on
* limiting the type of memory used for DMA transfers must
* happen before ehci_init() is called. */
switch (pdev->vendor) {
case PCI_VENDOR_ID_NVIDIA:
/* NVidia reports that certain chips don't handle
* QH, ITD, or SITD addresses above 2GB. (But TD,
* data buffer, and periodic schedule are normal.)
*/
switch (pdev->device) {
case 0x003c: /* MCP04 */
case 0x005b: /* CK804 */
case 0x00d8: /* CK8 */
case 0x00e8: /* CK8S */
if (pci_set_consistent_dma_mask(pdev,
DMA_BIT_MASK(31)) < 0)
ehci_warn(ehci, "can't enable NVidia "
"workaround for >2GB RAM\n");
break;
}
break;
}
/* cache this readonly data; minimize chip reads */
ehci->hcs_params = ehci_readl(ehci, &ehci->caps->hcs_params);
retval = ehci_halt(ehci);
if (retval)
return retval;
if ((pdev->vendor == PCI_VENDOR_ID_AMD && pdev->device == 0x7808) ||
(pdev->vendor == PCI_VENDOR_ID_ATI && pdev->device == 0x4396)) {
/* EHCI controller on AMD SB700/SB800/Hudson-2/3 platforms may
* read/write memory space which does not belong to it when
* there is NULL pointer with T-bit set to 1 in the frame list
* table. To avoid the issue, the frame list link pointer
* should always contain a valid pointer to a inactive qh.
*/
ehci->use_dummy_qh = 1;
ehci_info(ehci, "applying AMD SB700/SB800/Hudson-2/3 EHCI "
"dummy qh workaround\n");
}
/* data structure init */
retval = ehci_init(hcd);
if (retval)
return retval;
switch (pdev->vendor) {
case PCI_VENDOR_ID_NEC:
ehci->need_io_watchdog = 0;
break;
case PCI_VENDOR_ID_INTEL:
ehci->need_io_watchdog = 0;
ehci->fs_i_thresh = 1;
if (pdev->device == 0x27cc) {
ehci->broken_periodic = 1;
ehci_info(ehci, "using broken periodic workaround\n");
}
if (pdev->device == 0x0806 || pdev->device == 0x0811
|| pdev->device == 0x0829) {
ehci_info(ehci, "disable lpm for langwell/penwell\n");
ehci->has_lpm = 0;
}
if (pdev->device == PCI_DEVICE_ID_INTEL_CE4100_USB) {
hcd->has_tt = 1;
tdi_reset(ehci);
}
if (pdev->subsystem_vendor == PCI_VENDOR_ID_ASUSTEK) {
/* EHCI #1 or #2 on 6 Series/C200 Series chipset */
if (pdev->device == 0x1c26 || pdev->device == 0x1c2d) {
ehci_info(ehci, "broken D3 during system sleep on ASUS\n");
hcd->broken_pci_sleep = 1;
device_set_wakeup_capable(&pdev->dev, false);
}
}
break;
case PCI_VENDOR_ID_TDI:
if (pdev->device == PCI_DEVICE_ID_TDI_EHCI) {
hcd->has_tt = 1;
tdi_reset(ehci);
}
break;
case PCI_VENDOR_ID_AMD:
/* AMD PLL quirk */
if (usb_amd_find_chipset_info())
ehci->amd_pll_fix = 1;
/* AMD8111 EHCI doesn't work, according to AMD errata */
if (pdev->device == 0x7463) {
ehci_info(ehci, "ignoring AMD8111 (errata)\n");
retval = -EIO;
goto done;
}
break;
case PCI_VENDOR_ID_NVIDIA:
switch (pdev->device) {
/* Some NForce2 chips have problems with selective suspend;
* fixed in newer silicon.
*/
case 0x0068:
if (pdev->revision < 0xa4)
ehci->no_selective_suspend = 1;
break;
/* MCP89 chips on the MacBookAir3,1 give EPROTO when
* fetching device descriptors unless LPM is disabled.
* There are also intermittent problems enumerating
* devices with PPCD enabled.
*/
case 0x0d9d:
ehci_info(ehci, "disable lpm/ppcd for nvidia mcp89");
ehci->has_lpm = 0;
ehci->has_ppcd = 0;
ehci->command &= ~CMD_PPCEE;
break;
}
break;
case PCI_VENDOR_ID_VIA:
if (pdev->device == 0x3104 && (pdev->revision & 0xf0) == 0x60) {
u8 tmp;
/* The VT6212 defaults to a 1 usec EHCI sleep time which
* hogs the PCI bus *badly*. Setting bit 5 of 0x4B makes
* that sleep time use the conventional 10 usec.
*/
pci_read_config_byte(pdev, 0x4b, &tmp);
if (tmp & 0x20)
break;
pci_write_config_byte(pdev, 0x4b, tmp | 0x20);
}
break;
case PCI_VENDOR_ID_ATI:
/* AMD PLL quirk */
if (usb_amd_find_chipset_info())
ehci->amd_pll_fix = 1;
/* SB600 and old version of SB700 have a bug in EHCI controller,
* which causes usb devices lose response in some cases.
*/
if ((pdev->device == 0x4386) || (pdev->device == 0x4396)) {
p_smbus = pci_get_device(PCI_VENDOR_ID_ATI,
PCI_DEVICE_ID_ATI_SBX00_SMBUS,
NULL);
if (!p_smbus)
break;
rev = p_smbus->revision;
if ((pdev->device == 0x4386) || (rev == 0x3a)
|| (rev == 0x3b)) {
u8 tmp;
ehci_info(ehci, "applying AMD SB600/SB700 USB "
"freeze workaround\n");
pci_read_config_byte(pdev, 0x53, &tmp);
pci_write_config_byte(pdev, 0x53, tmp | (1<<3));
}
pci_dev_put(p_smbus);
}
break;
case PCI_VENDOR_ID_NETMOS:
/* MosChip frame-index-register bug */
ehci_info(ehci, "applying MosChip frame-index workaround\n");
ehci->frame_index_bug = 1;
break;
}
/* optional debug port, normally in the first BAR */
temp = pci_find_capability(pdev, 0x0a);
if (temp) {
pci_read_config_dword(pdev, temp, &temp);
temp >>= 16;
if ((temp & (3 << 13)) == (1 << 13)) {
temp &= 0x1fff;
ehci->debug = ehci_to_hcd(ehci)->regs + temp;
temp = ehci_readl(ehci, &ehci->debug->control);
ehci_info(ehci, "debug port %d%s\n",
HCS_DEBUG_PORT(ehci->hcs_params),
(temp & DBGP_ENABLED)
? " IN USE"
: "");
if (!(temp & DBGP_ENABLED))
ehci->debug = NULL;
}
}
ehci_reset(ehci);
/* at least the Genesys GL880S needs fixup here */
temp = HCS_N_CC(ehci->hcs_params) * HCS_N_PCC(ehci->hcs_params);
temp &= 0x0f;
if (temp && HCS_N_PORTS(ehci->hcs_params) > temp) {
ehci_dbg(ehci, "bogus port configuration: "
"cc=%d x pcc=%d < ports=%d\n",
HCS_N_CC(ehci->hcs_params),
HCS_N_PCC(ehci->hcs_params),
HCS_N_PORTS(ehci->hcs_params));
switch (pdev->vendor) {
case 0x17a0: /* GENESYS */
/* GL880S: should be PORTS=2 */
temp |= (ehci->hcs_params & ~0xf);
ehci->hcs_params = temp;
break;
case PCI_VENDOR_ID_NVIDIA:
/* NF4: should be PCC=10 */
break;
}
}
/* Serial Bus Release Number is at PCI 0x60 offset */
pci_read_config_byte(pdev, 0x60, &ehci->sbrn);
if (pdev->vendor == PCI_VENDOR_ID_STMICRO
&& pdev->device == PCI_DEVICE_ID_STMICRO_USB_HOST)
ehci->sbrn = 0x20; /* ConneXT has no sbrn register */
/* Keep this around for a while just in case some EHCI
* implementation uses legacy PCI PM support. This test
* can be removed on 17 Dec 2009 if the dev_warn() hasn't
* been triggered by then.
*/
if (!device_can_wakeup(&pdev->dev)) {
u16 port_wake;
pci_read_config_word(pdev, 0x62, &port_wake);
if (port_wake & 0x0001) {
dev_warn(&pdev->dev, "Enabling legacy PCI PM\n");
device_set_wakeup_capable(&pdev->dev, 1);
}
}
#ifdef CONFIG_USB_SUSPEND
/* REVISIT: the controller works fine for wakeup iff the root hub
* itself is "globally" suspended, but usbcore currently doesn't
* understand such things.
*
* System suspend currently expects to be able to suspend the entire
* device tree, device-at-a-time. If we failed selective suspend
* reports, system suspend would fail; so the root hub code must claim
* success. That's lying to usbcore, and it matters for runtime
* PM scenarios with selective suspend and remote wakeup...
*/
if (ehci->no_selective_suspend && device_can_wakeup(&pdev->dev))
ehci_warn(ehci, "selective suspend/wakeup unavailable\n");
#endif
ehci_port_power(ehci, 1);
retval = ehci_pci_reinit(ehci, pdev);
done:
return retval;
}
static void xhci_pci_quirks(struct device *dev, struct xhci_hcd *xhci)
{
struct pci_dev *pdev = to_pci_dev(dev);
/* Look for vendor-specific quirks */
if (pdev->vendor == PCI_VENDOR_ID_FRESCO_LOGIC &&
(pdev->device == PCI_DEVICE_ID_FRESCO_LOGIC_PDK ||
pdev->device == PCI_DEVICE_ID_FRESCO_LOGIC_FL1400)) {
if (pdev->device == PCI_DEVICE_ID_FRESCO_LOGIC_PDK &&
pdev->revision == 0x0) {
xhci->quirks |= XHCI_RESET_EP_QUIRK;
xhci_dbg_trace(xhci, trace_xhci_dbg_quirks,
"QUIRK: Fresco Logic xHC needs configure"
" endpoint cmd after reset endpoint");
}
if (pdev->device == PCI_DEVICE_ID_FRESCO_LOGIC_PDK &&
pdev->revision == 0x4) {
xhci->quirks |= XHCI_SLOW_SUSPEND;
xhci_dbg_trace(xhci, trace_xhci_dbg_quirks,
"QUIRK: Fresco Logic xHC revision %u"
"must be suspended extra slowly",
pdev->revision);
}
/* Fresco Logic confirms: all revisions of this chip do not
* support MSI, even though some of them claim to in their PCI
* capabilities.
*/
xhci->quirks |= XHCI_BROKEN_MSI;
xhci_dbg_trace(xhci, trace_xhci_dbg_quirks,
"QUIRK: Fresco Logic revision %u "
"has broken MSI implementation",
pdev->revision);
xhci->quirks |= XHCI_TRUST_TX_LENGTH;
}
if (pdev->vendor == PCI_VENDOR_ID_NEC)
xhci->quirks |= XHCI_NEC_HOST;
if (pdev->vendor == PCI_VENDOR_ID_AMD && xhci->hci_version == 0x96)
xhci->quirks |= XHCI_AMD_0x96_HOST;
/* AMD PLL quirk */
if (pdev->vendor == PCI_VENDOR_ID_AMD && usb_amd_find_chipset_info())
xhci->quirks |= XHCI_AMD_PLL_FIX;
if (pdev->vendor == PCI_VENDOR_ID_INTEL) {
xhci->quirks |= XHCI_LPM_SUPPORT;
xhci->quirks |= XHCI_INTEL_HOST;
}
if (pdev->vendor == PCI_VENDOR_ID_INTEL &&
pdev->device == PCI_DEVICE_ID_INTEL_PANTHERPOINT_XHCI) {
xhci->quirks |= XHCI_EP_LIMIT_QUIRK;
xhci->limit_active_eps = 64;
xhci->quirks |= XHCI_SW_BW_CHECKING;
/*
* PPT desktop boards DH77EB and DH77DF will power back on after
* a few seconds of being shutdown. The fix for this is to
* switch the ports from xHCI to EHCI on shutdown. We can't use
* DMI information to find those particular boards (since each
* vendor will change the board name), so we have to key off all
* PPT chipsets.
*/
xhci->quirks |= XHCI_SPURIOUS_REBOOT;
xhci->quirks |= XHCI_AVOID_BEI;
}
if (pdev->vendor == PCI_VENDOR_ID_INTEL &&
(pdev->device == PCI_DEVICE_ID_INTEL_LYNXPOINT_XHCI ||
pdev->device == PCI_DEVICE_ID_INTEL_LYNXPOINT_LP_XHCI)) {
/* Workaround for occasional spurious wakeups from S5 (or
* any other sleep) on Haswell machines with LPT and LPT-LP
* with the new Intel BIOS
*/
/* Limit the quirk to only known vendors, as this triggers
* yet another BIOS bug on some other machines
* https://bugzilla.kernel.org/show_bug.cgi?id=66171
*/
if (pdev->subsystem_vendor == PCI_VENDOR_ID_HP)
xhci->quirks |= XHCI_SPURIOUS_WAKEUP;
}
if (pdev->vendor == PCI_VENDOR_ID_ETRON &&
pdev->device == PCI_DEVICE_ID_ASROCK_P67) {
xhci->quirks |= XHCI_RESET_ON_RESUME;
xhci_dbg_trace(xhci, trace_xhci_dbg_quirks,
"QUIRK: Resetting on resume");
xhci->quirks |= XHCI_TRUST_TX_LENGTH;
}
if (pdev->vendor == PCI_VENDOR_ID_RENESAS &&
pdev->device == 0x0015 &&
pdev->subsystem_vendor == PCI_VENDOR_ID_SAMSUNG &&
pdev->subsystem_device == 0xc0cd)
xhci->quirks |= XHCI_RESET_ON_RESUME;
if (pdev->vendor == PCI_VENDOR_ID_VIA)
xhci->quirks |= XHCI_RESET_ON_RESUME;
}
/* called during probe() after chip reset completes */
static int xhci_pci_setup(struct usb_hcd *hcd)
{
struct xhci_hcd *xhci;
struct pci_dev *pdev = to_pci_dev(hcd->self.controller);
int retval;
u32 temp;
hcd->self.sg_tablesize = TRBS_PER_SEGMENT - 2;
if (usb_hcd_is_primary_hcd(hcd)) {
xhci = kzalloc(sizeof(struct xhci_hcd), GFP_KERNEL);
if (!xhci)
return -ENOMEM;
*((struct xhci_hcd **) hcd->hcd_priv) = xhci;
xhci->main_hcd = hcd;
/* Mark the first roothub as being USB 2.0.
* The xHCI driver will register the USB 3.0 roothub.
*/
hcd->speed = HCD_USB2;
hcd->self.root_hub->speed = USB_SPEED_HIGH;
/*
* USB 2.0 roothub under xHCI has an integrated TT,
* (rate matching hub) as opposed to having an OHCI/UHCI
* companion controller.
*/
hcd->has_tt = 1;
} else {
/* xHCI private pointer was set in xhci_pci_probe for the second
* registered roothub.
*/
xhci = hcd_to_xhci(hcd);
temp = xhci_readl(xhci, &xhci->cap_regs->hcc_params);
if (HCC_64BIT_ADDR(temp)) {
xhci_dbg(xhci, "Enabling 64-bit DMA addresses.\n");
dma_set_mask(hcd->self.controller, DMA_BIT_MASK(64));
} else {
dma_set_mask(hcd->self.controller, DMA_BIT_MASK(32));
}
return 0;
}
xhci->cap_regs = hcd->regs;
xhci->op_regs = hcd->regs +
HC_LENGTH(xhci_readl(xhci, &xhci->cap_regs->hc_capbase));
xhci->run_regs = hcd->regs +
(xhci_readl(xhci, &xhci->cap_regs->run_regs_off) & RTSOFF_MASK);
/* Cache read-only capability registers */
xhci->hcs_params1 = xhci_readl(xhci, &xhci->cap_regs->hcs_params1);
xhci->hcs_params2 = xhci_readl(xhci, &xhci->cap_regs->hcs_params2);
xhci->hcs_params3 = xhci_readl(xhci, &xhci->cap_regs->hcs_params3);
xhci->hcc_params = xhci_readl(xhci, &xhci->cap_regs->hc_capbase);
xhci->hci_version = HC_VERSION(xhci->hcc_params);
xhci->hcc_params = xhci_readl(xhci, &xhci->cap_regs->hcc_params);
xhci_print_registers(xhci);
/* Look for vendor-specific quirks */
if (pdev->vendor == PCI_VENDOR_ID_FRESCO_LOGIC &&
(pdev->device == PCI_DEVICE_ID_FRESCO_LOGIC_PDK ||
pdev->device == PCI_DEVICE_ID_FRESCO_LOGIC_FL1400)) {
if (pdev->device == PCI_DEVICE_ID_FRESCO_LOGIC_PDK &&
pdev->revision == 0x0) {
xhci->quirks |= XHCI_RESET_EP_QUIRK;
xhci_dbg(xhci, "QUIRK: Fresco Logic xHC needs configure"
" endpoint cmd after reset endpoint\n");
}
/* Fresco Logic confirms: all revisions of this chip do not
* support MSI, even though some of them claim to in their PCI
* capabilities.
*/
xhci->quirks |= XHCI_BROKEN_MSI;
xhci_dbg(xhci, "QUIRK: Fresco Logic revision %u "
"has broken MSI implementation\n",
pdev->revision);
xhci->quirks |= XHCI_TRUST_TX_LENGTH;
}
if (pdev->vendor == PCI_VENDOR_ID_NEC)
xhci->quirks |= XHCI_NEC_HOST;
if (pdev->vendor == PCI_VENDOR_ID_AMD && xhci->hci_version == 0x96)
xhci->quirks |= XHCI_AMD_0x96_HOST;
/* AMD PLL quirk */
if (pdev->vendor == PCI_VENDOR_ID_AMD && usb_amd_find_chipset_info())
xhci->quirks |= XHCI_AMD_PLL_FIX;
if (pdev->vendor == PCI_VENDOR_ID_INTEL &&
pdev->device == PCI_DEVICE_ID_INTEL_PANTHERPOINT_XHCI) {
xhci->quirks |= XHCI_SPURIOUS_SUCCESS;
xhci->quirks |= XHCI_EP_LIMIT_QUIRK;
xhci->limit_active_eps = 64;
/*
* PPT desktop boards DH77EB and DH77DF will power back on after
* a few seconds of being shutdown. The fix for this is to
* switch the ports from xHCI to EHCI on shutdown. We can't use
* DMI information to find those particular boards (since each
* vendor will change the board name), so we have to key off all
* PPT chipsets.
*/
xhci->quirks |= XHCI_SPURIOUS_REBOOT;
}
if (pdev->vendor == PCI_VENDOR_ID_ETRON &&
pdev->device == PCI_DEVICE_ID_ASROCK_P67) {
xhci->quirks |= XHCI_RESET_ON_RESUME;
xhci_dbg(xhci, "QUIRK: Resetting on resume\n");
xhci->quirks |= XHCI_TRUST_TX_LENGTH;
}
if (pdev->vendor == PCI_VENDOR_ID_VIA)
xhci->quirks |= XHCI_RESET_ON_RESUME;
/* Make sure the HC is halted. */
retval = xhci_halt(xhci);
if (retval)
goto error;
xhci_dbg(xhci, "Resetting HCD\n");
/* Reset the internal HC memory state and registers. */
retval = xhci_reset(xhci);
if (retval)
goto error;
xhci_dbg(xhci, "Reset complete\n");
temp = xhci_readl(xhci, &xhci->cap_regs->hcc_params);
if (HCC_64BIT_ADDR(temp)) {
xhci_dbg(xhci, "Enabling 64-bit DMA addresses.\n");
dma_set_mask(hcd->self.controller, DMA_BIT_MASK(64));
} else {
dma_set_mask(hcd->self.controller, DMA_BIT_MASK(32));
}
xhci_dbg(xhci, "Calling HCD init\n");
/* Initialize HCD and host controller data structures. */
retval = xhci_init(hcd);
if (retval)
goto error;
xhci_dbg(xhci, "Called HCD init\n");
pci_read_config_byte(pdev, XHCI_SBRN_OFFSET, &xhci->sbrn);
xhci_dbg(xhci, "Got SBRN %u\n", (unsigned int) xhci->sbrn);
/* Find any debug ports */
retval = xhci_pci_reinit(xhci, pdev);
if (!retval)
return retval;
error:
kfree(xhci);
return retval;
}
static int ehci_pci_setup(struct usb_hcd *hcd)
{
struct ehci_hcd *ehci = hcd_to_ehci(hcd);
struct pci_dev *pdev = to_pci_dev(hcd->self.controller);
struct pci_dev *p_smbus;
u8 rev;
u32 temp;
int retval;
switch (pdev->vendor) {
case PCI_VENDOR_ID_TOSHIBA_2:
if (pdev->device == 0x01b5) {
#ifdef CONFIG_USB_EHCI_BIG_ENDIAN_MMIO
ehci->big_endian_mmio = 1;
#else
ehci_warn(ehci,
"unsupported big endian Toshiba quirk\n");
#endif
}
break;
}
ehci->caps = hcd->regs;
ehci->regs = hcd->regs +
HC_LENGTH(ehci, ehci_readl(ehci, &ehci->caps->hc_capbase));
dbg_hcs_params(ehci, "reset");
dbg_hcc_params(ehci, "reset");
switch (pdev->vendor) {
case PCI_VENDOR_ID_NVIDIA:
switch (pdev->device) {
case 0x003c:
case 0x005b:
case 0x00d8:
case 0x00e8:
if (pci_set_consistent_dma_mask(pdev,
DMA_BIT_MASK(31)) < 0)
ehci_warn(ehci, "can't enable NVidia "
"workaround for >2GB RAM\n");
break;
}
break;
}
ehci->hcs_params = ehci_readl(ehci, &ehci->caps->hcs_params);
retval = ehci_halt(ehci);
if (retval)
return retval;
if ((pdev->vendor == PCI_VENDOR_ID_AMD && pdev->device == 0x7808) ||
(pdev->vendor == PCI_VENDOR_ID_ATI && pdev->device == 0x4396)) {
ehci->use_dummy_qh = 1;
ehci_info(ehci, "applying AMD SB700/SB800/Hudson-2/3 EHCI "
"dummy qh workaround\n");
}
retval = ehci_init(hcd);
if (retval)
return retval;
switch (pdev->vendor) {
case PCI_VENDOR_ID_NEC:
ehci->need_io_watchdog = 0;
break;
case PCI_VENDOR_ID_INTEL:
ehci->need_io_watchdog = 0;
ehci->fs_i_thresh = 1;
if (pdev->device == 0x27cc) {
ehci->broken_periodic = 1;
ehci_info(ehci, "using broken periodic workaround\n");
}
if (pdev->device == 0x0806 || pdev->device == 0x0811
|| pdev->device == 0x0829) {
ehci_info(ehci, "disable lpm for langwell/penwell\n");
ehci->has_lpm = 0;
}
if (pdev->device == PCI_DEVICE_ID_INTEL_CE4100_USB) {
hcd->has_tt = 1;
tdi_reset(ehci);
}
if (pdev->subsystem_vendor == PCI_VENDOR_ID_ASUSTEK) {
if (pdev->device == 0x1c26 || pdev->device == 0x1c2d) {
ehci_info(ehci, "broken D3 during system sleep on ASUS\n");
hcd->broken_pci_sleep = 1;
device_set_wakeup_capable(&pdev->dev, false);
}
}
break;
case PCI_VENDOR_ID_TDI:
if (pdev->device == PCI_DEVICE_ID_TDI_EHCI) {
hcd->has_tt = 1;
tdi_reset(ehci);
}
break;
case PCI_VENDOR_ID_AMD:
if (usb_amd_find_chipset_info())
ehci->amd_pll_fix = 1;
if (pdev->device == 0x7463) {
ehci_info(ehci, "ignoring AMD8111 (errata)\n");
retval = -EIO;
goto done;
}
break;
case PCI_VENDOR_ID_NVIDIA:
switch (pdev->device) {
case 0x0068:
if (pdev->revision < 0xa4)
ehci->no_selective_suspend = 1;
break;
case 0x0d9d:
ehci_info(ehci, "disable lpm/ppcd for nvidia mcp89");
ehci->has_lpm = 0;
ehci->has_ppcd = 0;
ehci->command &= ~CMD_PPCEE;
break;
}
break;
case PCI_VENDOR_ID_VIA:
if (pdev->device == 0x3104 && (pdev->revision & 0xf0) == 0x60) {
u8 tmp;
pci_read_config_byte(pdev, 0x4b, &tmp);
if (tmp & 0x20)
break;
pci_write_config_byte(pdev, 0x4b, tmp | 0x20);
}
break;
case PCI_VENDOR_ID_ATI:
if (usb_amd_find_chipset_info())
ehci->amd_pll_fix = 1;
if ((pdev->device == 0x4386) || (pdev->device == 0x4396)) {
p_smbus = pci_get_device(PCI_VENDOR_ID_ATI,
PCI_DEVICE_ID_ATI_SBX00_SMBUS,
NULL);
if (!p_smbus)
break;
rev = p_smbus->revision;
if ((pdev->device == 0x4386) || (rev == 0x3a)
|| (rev == 0x3b)) {
u8 tmp;
ehci_info(ehci, "applying AMD SB600/SB700 USB "
"freeze workaround\n");
pci_read_config_byte(pdev, 0x53, &tmp);
pci_write_config_byte(pdev, 0x53, tmp | (1<<3));
}
pci_dev_put(p_smbus);
}
break;
case PCI_VENDOR_ID_NETMOS:
ehci_info(ehci, "applying MosChip frame-index workaround\n");
ehci->frame_index_bug = 1;
break;
}
temp = pci_find_capability(pdev, 0x0a);
if (temp) {
pci_read_config_dword(pdev, temp, &temp);
temp >>= 16;
if ((temp & (3 << 13)) == (1 << 13)) {
temp &= 0x1fff;
ehci->debug = ehci_to_hcd(ehci)->regs + temp;
temp = ehci_readl(ehci, &ehci->debug->control);
ehci_info(ehci, "debug port %d%s\n",
HCS_DEBUG_PORT(ehci->hcs_params),
(temp & DBGP_ENABLED)
? " IN USE"
: "");
if (!(temp & DBGP_ENABLED))
ehci->debug = NULL;
}
}
ehci_reset(ehci);
temp = HCS_N_CC(ehci->hcs_params) * HCS_N_PCC(ehci->hcs_params);
temp &= 0x0f;
if (temp && HCS_N_PORTS(ehci->hcs_params) > temp) {
ehci_dbg(ehci, "bogus port configuration: "
"cc=%d x pcc=%d < ports=%d\n",
HCS_N_CC(ehci->hcs_params),
HCS_N_PCC(ehci->hcs_params),
HCS_N_PORTS(ehci->hcs_params));
switch (pdev->vendor) {
case 0x17a0:
temp |= (ehci->hcs_params & ~0xf);
ehci->hcs_params = temp;
break;
case PCI_VENDOR_ID_NVIDIA:
break;
}
}
pci_read_config_byte(pdev, 0x60, &ehci->sbrn);
if (pdev->vendor == PCI_VENDOR_ID_STMICRO
&& pdev->device == PCI_DEVICE_ID_STMICRO_USB_HOST)
ehci->sbrn = 0x20;
if (!device_can_wakeup(&pdev->dev)) {
u16 port_wake;
pci_read_config_word(pdev, 0x62, &port_wake);
if (port_wake & 0x0001) {
dev_warn(&pdev->dev, "Enabling legacy PCI PM\n");
device_set_wakeup_capable(&pdev->dev, 1);
}
}
#ifdef CONFIG_USB_SUSPEND
if (ehci->no_selective_suspend && device_can_wakeup(&pdev->dev))
ehci_warn(ehci, "selective suspend/wakeup unavailable\n");
#endif
ehci_port_power(ehci, 1);
retval = ehci_pci_reinit(ehci, pdev);
done:
return retval;
}
bool usb_amd_prefetch_quirk(void)
{
usb_amd_find_chipset_info();
/* SB800 needs pre-fetch fix */
return amd_chipset.sb_type.gen == AMD_CHIPSET_SB800;
}