unsigned long va_to_phys(unsigned long address)
{
pte_t *pte;
pte = va_to_pte(address);
if (pte)
return(((unsigned long)(pte_val(*pte)) & PAGE_MASK) | (address & ~(PAGE_MASK-1)));
return (0);
}
void
m8xx_cpm_reset(uint host_page_addr)
{
volatile immap_t *imp;
volatile cpm8xx_t *commproc;
pte_t *pte;
imp = (immap_t *)IMAP_ADDR;
commproc = (cpm8xx_t *)&imp->im_cpm;
#ifdef notdef
/* We can't do this. It seems to blow away the microcode
* patch that EPPC-Bug loaded for us. EPPC-Bug uses SCC1 for
* Ethernet, SMC1 for the console, and I2C for serial EEPROM.
* Our own drivers quickly reset all of these.
*/
/* Perform a reset.
*/
commproc->cp_cpcr = (CPM_CR_RST | CPM_CR_FLG);
/* Wait for it.
*/
while (commproc->cp_cpcr & CPM_CR_FLG);
#endif
/* Set SDMA Bus Request priority 5.
* On 860T, this also enables FEC priority 6. I am not sure
* this is what we realy want for some applications, but the
* manual recommends it.
* Bit 25, FAM can also be set to use FEC aggressive mode (860T).
*/
imp->im_siu_conf.sc_sdcr = 1;
/* Reclaim the DP memory for our use.
*/
dp_alloc_base = CPM_DATAONLY_BASE;
dp_alloc_top = dp_alloc_base + CPM_DATAONLY_SIZE;
/* Set the host page for allocation.
*/
host_buffer = host_page_addr; /* Host virtual page address */
host_end = host_page_addr + PAGE_SIZE;
pte = va_to_pte(&init_task, host_page_addr);
pte_val(*pte) |= _PAGE_NO_CACHE;
flush_tlb_page(current->mm->mmap, host_buffer);
/* Tell everyone where the comm processor resides.
*/
cpmp = (cpm8xx_t *)commproc;
/* Initialize the CPM interrupt controller.
*/
((immap_t *)IMAP_ADDR)->im_cpic.cpic_cicr =
(CICR_SCD_SCC4 | CICR_SCC_SCC3 | CICR_SCB_SCC2 | CICR_SCA_SCC1) |
(((5)/2) << 13) | CICR_HP_MASK;
/* I hard coded the CPM interrupt to 5 above
* since the CPM_INTERRUPT define is relative to
* the linux irq structure not what the hardware
* belives. -- Cort
*/
((immap_t *)IMAP_ADDR)->im_cpic.cpic_cimr = 0;
/* Set our interrupt handler with the core CPU.
*/
if (request_irq(CPM_INTERRUPT, cpm_interrupt, 0, "cpm", NULL) != 0)
panic("Could not allocate CPM IRQ!");
/* Install our own error handler.
*/
cpm_install_handler(CPMVEC_ERROR, cpm_error_interrupt, NULL);
((immap_t *)IMAP_ADDR)->im_cpic.cpic_cicr |= CICR_IEN;
}
int __init m8xx_enet_init(void)
{
struct device *dev;
struct cpm_enet_private *cep;
int i, j;
unsigned char *eap;
unsigned long mem_addr;
pte_t *pte;
bd_t *bd;
volatile cbd_t *bdp;
volatile cpm8xx_t *cp;
volatile scc_t *sccp;
volatile scc_enet_t *ep;
volatile immap_t *immap;
cp = cpmp; /* Get pointer to Communication Processor */
immap = (immap_t *)IMAP_ADDR; /* and to internal registers */
bd = (bd_t *)res;
/* Allocate some private information.
*/
cep = (struct cpm_enet_private *)kmalloc(sizeof(*cep), GFP_KERNEL);
/*memset(cep, 0, sizeof(*cep));*/
__clear_user(cep,sizeof(*cep));
/* Create an Ethernet device instance.
*/
dev = init_etherdev(0, 0);
/* Get pointer to SCC area in parameter RAM.
*/
ep = (scc_enet_t *)(&cp->cp_dparam[PROFF_ENET]);
/* And another to the SCC register area.
*/
sccp = (volatile scc_t *)(&cp->cp_scc[SCC_ENET]);
cep->sccp = (scc_t *)sccp; /* Keep the pointer handy */
/* Disable receive and transmit in case EPPC-Bug started it.
*/
sccp->scc_gsmrl &= ~(SCC_GSMRL_ENR | SCC_GSMRL_ENT);
/* Cookbook style from the MPC860 manual.....
* Not all of this is necessary if EPPC-Bug has initialized
* the network.
* So far we are lucky, all board configurations use the same
* pins, or at least the same I/O Port for these functions.....
* It can't last though......
*/
/* Configure port A pins for Txd and Rxd.
*/
immap->im_ioport.iop_papar |= (PA_ENET_RXD | PA_ENET_TXD);
immap->im_ioport.iop_padir &= ~(PA_ENET_RXD | PA_ENET_TXD);
immap->im_ioport.iop_paodr &= ~PA_ENET_TXD;
/* Configure port C pins to enable CLSN and RENA.
*/
immap->im_ioport.iop_pcpar &= ~(PC_ENET_CLSN | PC_ENET_RENA);
immap->im_ioport.iop_pcdir &= ~(PC_ENET_CLSN | PC_ENET_RENA);
immap->im_ioport.iop_pcso |= (PC_ENET_CLSN | PC_ENET_RENA);
/* Configure port A for TCLK and RCLK.
*/
immap->im_ioport.iop_papar |= (PA_ENET_TCLK | PA_ENET_RCLK);
immap->im_ioport.iop_padir &= ~(PA_ENET_TCLK | PA_ENET_RCLK);
/* Configure Serial Interface clock routing.
* First, clear all SCC bits to zero, then set the ones we want.
*/
cp->cp_sicr &= ~SICR_ENET_MASK;
cp->cp_sicr |= SICR_ENET_CLKRT;
/* Manual says set SDDR, but I can't find anything with that
* name. I think it is a misprint, and should be SDCR. This
* has already been set by the communication processor initialization.
*/
/* Allocate space for the buffer descriptors in the DP ram.
* These are relative offsets in the DP ram address space.
* Initialize base addresses for the buffer descriptors.
*/
i = m8xx_cpm_dpalloc(sizeof(cbd_t) * RX_RING_SIZE);
ep->sen_genscc.scc_rbase = i;
cep->rx_bd_base = (cbd_t *)&cp->cp_dpmem[i];
i = m8xx_cpm_dpalloc(sizeof(cbd_t) * TX_RING_SIZE);
ep->sen_genscc.scc_tbase = i;
cep->tx_bd_base = (cbd_t *)&cp->cp_dpmem[i];
cep->dirty_tx = cep->cur_tx = cep->tx_bd_base;
cep->cur_rx = cep->rx_bd_base;
/* Issue init Rx BD command for SCC.
* Manual says to perform an Init Rx parameters here. We have
* to perform both Rx and Tx because the SCC may have been
* already running.
* In addition, we have to do it later because we don't yet have
* all of the BD control/status set properly.
cp->cp_cpcr = mk_cr_cmd(CPM_CR_ENET, CPM_CR_INIT_RX) | CPM_CR_FLG;
while (cp->cp_cpcr & CPM_CR_FLG);
*/
/* Initialize function code registers for big-endian.
*/
ep->sen_genscc.scc_rfcr = SCC_EB;
ep->sen_genscc.scc_tfcr = SCC_EB;
/* Set maximum bytes per receive buffer.
* This appears to be an Ethernet frame size, not the buffer
* fragment size. It must be a multiple of four.
*/
ep->sen_genscc.scc_mrblr = PKT_MAXBLR_SIZE;
/* Set CRC preset and mask.
*/
ep->sen_cpres = 0xffffffff;
ep->sen_cmask = 0xdebb20e3;
ep->sen_crcec = 0; /* CRC Error counter */
ep->sen_alec = 0; /* alignment error counter */
ep->sen_disfc = 0; /* discard frame counter */
ep->sen_pads = 0x8888; /* Tx short frame pad character */
ep->sen_retlim = 15; /* Retry limit threshold */
ep->sen_maxflr = PKT_MAXBUF_SIZE; /* maximum frame length register */
ep->sen_minflr = PKT_MINBUF_SIZE; /* minimum frame length register */
ep->sen_maxd1 = PKT_MAXBUF_SIZE; /* maximum DMA1 length */
ep->sen_maxd2 = PKT_MAXBUF_SIZE; /* maximum DMA2 length */
/* Clear hash tables.
*/
ep->sen_gaddr1 = 0;
ep->sen_gaddr2 = 0;
ep->sen_gaddr3 = 0;
ep->sen_gaddr4 = 0;
ep->sen_iaddr1 = 0;
ep->sen_iaddr2 = 0;
ep->sen_iaddr3 = 0;
ep->sen_iaddr4 = 0;
/* Set Ethernet station address.
*
* If we performed a MBX diskless boot, the Ethernet controller
* has been initialized and we copy the address out into our
* own structure.
*/
eap = (unsigned char *)&(ep->sen_paddrh);
#ifndef CONFIG_MBX
for (i=5; i>=0; i--)
*eap++ = dev->dev_addr[i] = bd->bi_enetaddr[i];
#else
for (i=5; i>=0; i--)
dev->dev_addr[i] = *eap++;
#endif
ep->sen_pper = 0; /* 'cause the book says so */
ep->sen_taddrl = 0; /* temp address (LSB) */
ep->sen_taddrm = 0;
ep->sen_taddrh = 0; /* temp address (MSB) */
/* Now allocate the host memory pages and initialize the
* buffer descriptors.
*/
bdp = cep->tx_bd_base;
for (i=0; i<TX_RING_SIZE; i++) {
/* Initialize the BD for every fragment in the page.
*/
bdp->cbd_sc = 0;
bdp->cbd_bufaddr = 0;
bdp++;
}
/* Set the last buffer to wrap.
*/
bdp--;
bdp->cbd_sc |= BD_SC_WRAP;
bdp = cep->rx_bd_base;
for (i=0; i<CPM_ENET_RX_PAGES; i++) {
/* Allocate a page.
*/
mem_addr = __get_free_page(GFP_KERNEL);
/* Make it uncached.
*/
pte = va_to_pte(&init_task, mem_addr);
pte_val(*pte) |= _PAGE_NO_CACHE;
flush_tlb_page(current->mm->mmap, mem_addr);
/* Initialize the BD for every fragment in the page.
*/
for (j=0; j<CPM_ENET_RX_FRPPG; j++) {
bdp->cbd_sc = BD_ENET_RX_EMPTY | BD_ENET_RX_INTR;
bdp->cbd_bufaddr = __pa(mem_addr);
mem_addr += CPM_ENET_RX_FRSIZE;
bdp++;
}
}
/* Set the last buffer to wrap.
*/
bdp--;
bdp->cbd_sc |= BD_SC_WRAP;
/* Let's re-initialize the channel now. We have to do it later
* than the manual describes because we have just now finished
* the BD initialization.
*/
cp->cp_cpcr = mk_cr_cmd(CPM_CR_ENET, CPM_CR_INIT_TRX) | CPM_CR_FLG;
while (cp->cp_cpcr & CPM_CR_FLG);
cep->skb_cur = cep->skb_dirty = 0;
sccp->scc_scce = 0xffff; /* Clear any pending events */
/* Enable interrupts for transmit error, complete frame
* received, and any transmit buffer we have also set the
* interrupt flag.
*/
sccp->scc_sccm = (SCCE_ENET_TXE | SCCE_ENET_RXF | SCCE_ENET_TXB);
/* Install our interrupt handler.
*/
cpm_install_handler(CPMVEC_ENET, cpm_enet_interrupt, dev);
/* Set GSMR_H to enable all normal operating modes.
* Set GSMR_L to enable Ethernet to MC68160.
*/
sccp->scc_gsmrh = 0;
sccp->scc_gsmrl = (SCC_GSMRL_TCI | SCC_GSMRL_TPL_48 | SCC_GSMRL_TPP_10 | SCC_GSMRL_MODE_ENET);
/* Set sync/delimiters.
*/
sccp->scc_dsr = 0xd555;
/* Set processing mode. Use Ethernet CRC, catch broadcast, and
* start frame search 22 bit times after RENA.
*/
sccp->scc_pmsr = (SCC_PMSR_ENCRC | SCC_PMSR_NIB22);
/* It is now OK to enable the Ethernet transmitter.
* Unfortunately, there are board implementation differences here.
*/
#ifdef CONFIG_MBX
immap->im_ioport.iop_pcpar |= PC_ENET_TENA;
immap->im_ioport.iop_pcdir &= ~PC_ENET_TENA;
#endif
#if defined(CONFIG_RPXLITE) || defined(CONFIG_RPXCLASSIC)
cp->cp_pbpar |= PB_ENET_TENA;
cp->cp_pbdir |= PB_ENET_TENA;
/* And while we are here, set the configuration to enable ethernet.
*/
*((volatile uint *)RPX_CSR_ADDR) &= ~BCSR0_ETHLPBK;
*((volatile uint *)RPX_CSR_ADDR) |=
(BCSR0_ETHEN | BCSR0_COLTESTDIS | BCSR0_FULLDPLXDIS);
#endif
#ifdef CONFIG_BSEIP
cp->cp_pbpar |= PB_ENET_TENA;
cp->cp_pbdir |= PB_ENET_TENA;
/* BSE uses port B and C for PHY control.
*/
cp->cp_pbpar &= ~(PB_BSE_POWERUP | PB_BSE_FDXDIS);
cp->cp_pbdir |= (PB_BSE_POWERUP | PB_BSE_FDXDIS);
cp->cp_pbdat |= (PB_BSE_POWERUP | PB_BSE_FDXDIS);
immap->im_ioport.iop_pcpar &= ~PC_BSE_LOOPBACK;
immap->im_ioport.iop_pcdir |= PC_BSE_LOOPBACK;
immap->im_ioport.iop_pcso &= ~PC_BSE_LOOPBACK;
immap->im_ioport.iop_pcdat &= ~PC_BSE_LOOPBACK;
#endif
dev->base_addr = (unsigned long)ep;
dev->priv = cep;
dev->name = "CPM_ENET";
/* The CPM Ethernet specific entries in the device structure. */
dev->open = cpm_enet_open;
dev->hard_start_xmit = cpm_enet_start_xmit;
dev->stop = cpm_enet_close;
dev->get_stats = cpm_enet_get_stats;
dev->set_multicast_list = set_multicast_list;
/* And last, enable the transmit and receive processing.
*/
sccp->scc_gsmrl |= (SCC_GSMRL_ENR | SCC_GSMRL_ENT);
printk("CPM ENET Version 0.1, ");
for (i=0; i<5; i++)
printk("%02x:", dev->dev_addr[i]);
printk("%02x\n", dev->dev_addr[5]);
return 0;
}
