int lpc_early_init(const void *blob, int node, pci_dev_t dev)
{
struct reg_info {
u32 base;
u32 size;
} values[4], *ptr;
int count;
int i;
count = fdtdec_get_int_array_count(blob, node, "intel,gen-dec",
(u32 *)values, sizeof(values) / sizeof(u32));
if (count < 0)
return -EINVAL;
/* Set COM1/COM2 decode range */
x86_pci_write_config16(dev, LPC_IO_DEC, 0x0010);
/* Enable PS/2 Keyboard/Mouse, EC areas and COM1 */
x86_pci_write_config16(dev, LPC_EN, KBC_LPC_EN | MC_LPC_EN |
GAMEL_LPC_EN | COMA_LPC_EN);
/* Write all registers but use 0 if we run out of data */
count = count * sizeof(u32) / sizeof(values[0]);
for (i = 0, ptr = values; i < ARRAY_SIZE(values); i++, ptr++) {
u32 reg = 0;
if (i < count)
reg = ptr->base | PCI_COMMAND_IO | (ptr->size << 16);
x86_pci_write_config32(dev, LPC_GENX_DEC(i), reg);
}
return 0;
}
static void qemu_chipset_init(void)
{
u16 device, xbcs;
int pam, i;
/*
* i440FX and Q35 chipset have different PAM register offset, but with
* the same bitfield layout. Here we determine the offset based on its
* PCI device ID.
*/
device = x86_pci_read_config16(PCI_BDF(0, 0, 0), PCI_DEVICE_ID);
i440fx = (device == PCI_DEVICE_ID_INTEL_82441);
pam = i440fx ? I440FX_PAM : Q35_PAM;
/*
* Initialize Programmable Attribute Map (PAM) Registers
*
* Configure legacy segments C/D/E/F to system RAM
*/
for (i = 0; i < PAM_NUM; i++)
x86_pci_write_config8(PCI_BDF(0, 0, 0), pam + i, PAM_RW);
if (i440fx) {
/*
* Enable legacy IDE I/O ports decode
*
* Note: QEMU always decode legacy IDE I/O port on PIIX chipset.
* However Linux ata_piix driver does sanity check on these two
* registers to see whether legacy ports decode is turned on.
* This is to make Linux ata_piix driver happy.
*/
x86_pci_write_config16(PIIX_IDE, IDE0_TIM, IDE_DECODE_EN);
x86_pci_write_config16(PIIX_IDE, IDE1_TIM, IDE_DECODE_EN);
/* Enable I/O APIC */
xbcs = x86_pci_read_config16(PIIX_ISA, XBCS);
xbcs |= APIC_EN;
x86_pci_write_config16(PIIX_ISA, XBCS, xbcs);
enable_pm_piix();
} else {
/* Configure PCIe ECAM base address */
x86_pci_write_config32(PCI_BDF(0, 0, 0), PCIEX_BAR,
CONFIG_PCIE_ECAM_BASE | BAR_EN);
enable_pm_ich9();
}
qemu_fwcfg_init();
}
static void enable_clock_gating(pci_dev_t dev)
{
u32 reg32;
u16 reg16;
setbits_le32(RCB_REG(0x2234), 0xf);
reg16 = x86_pci_read_config16(dev, GEN_PMCON_1);
reg16 |= (1 << 2) | (1 << 11);
x86_pci_write_config16(dev, GEN_PMCON_1, reg16);
pch_iobp_update(0xEB007F07, ~0UL, (1 << 31));
pch_iobp_update(0xEB004000, ~0UL, (1 << 7));
pch_iobp_update(0xEC007F07, ~0UL, (1 << 31));
pch_iobp_update(0xEC004000, ~0UL, (1 << 7));
reg32 = readl(RCB_REG(CG));
reg32 |= (1 << 31);
reg32 |= (1 << 29) | (1 << 28);
reg32 |= (1 << 27) | (1 << 26) | (1 << 25) | (1 << 24);
reg32 |= (1 << 16);
reg32 |= (1 << 17);
reg32 |= (1 << 18);
reg32 |= (1 << 22);
reg32 |= (1 << 23);
reg32 &= ~(1 << 20);
reg32 |= (1 << 19);
reg32 |= (1 << 0);
reg32 |= (0xf << 1);
writel(reg32, RCB_REG(CG));
setbits_le32(RCB_REG(0x38c0), 0x7);
setbits_le32(RCB_REG(0x36d4), 0x6680c004);
setbits_le32(RCB_REG(0x3564), 0x3);
}
static void enable_pm_piix(void)
{
u8 en;
u16 cmd;
/* Set the PM I/O base */
x86_pci_write_config32(PIIX_PM, PMBA, CONFIG_ACPI_PM1_BASE | 1);
/* Enable access to the PM I/O space */
cmd = x86_pci_read_config16(PIIX_PM, PCI_COMMAND);
cmd |= PCI_COMMAND_IO;
x86_pci_write_config16(PIIX_PM, PCI_COMMAND, cmd);
/* PM I/O Space Enable (PMIOSE) */
en = x86_pci_read_config8(PIIX_PM, PMREGMISC);
en |= PMIOSE;
x86_pci_write_config8(PIIX_PM, PMREGMISC, en);
}
int board_pci_post_scan(struct pci_controller *hose)
{
int ret = 0;
u16 device, xbcs;
int pam, i;
pci_dev_t vga;
ulong start;
/*
* i440FX and Q35 chipset have different PAM register offset, but with
* the same bitfield layout. Here we determine the offset based on its
* PCI device ID.
*/
device = x86_pci_read_config16(PCI_BDF(0, 0, 0), PCI_DEVICE_ID);
i440fx = (device == PCI_DEVICE_ID_INTEL_82441);
pam = i440fx ? I440FX_PAM : Q35_PAM;
/*
* Initialize Programmable Attribute Map (PAM) Registers
*
* Configure legacy segments C/D/E/F to system RAM
*/
for (i = 0; i < PAM_NUM; i++)
x86_pci_write_config8(PCI_BDF(0, 0, 0), pam + i, PAM_RW);
if (i440fx) {
/*
* Enable legacy IDE I/O ports decode
*
* Note: QEMU always decode legacy IDE I/O port on PIIX chipset.
* However Linux ata_piix driver does sanity check on these two
* registers to see whether legacy ports decode is turned on.
* This is to make Linux ata_piix driver happy.
*/
x86_pci_write_config16(PIIX_IDE, IDE0_TIM, IDE_DECODE_EN);
x86_pci_write_config16(PIIX_IDE, IDE1_TIM, IDE_DECODE_EN);
/* Enable I/O APIC */
xbcs = x86_pci_read_config16(PIIX_ISA, XBCS);
xbcs |= APIC_EN;
x86_pci_write_config16(PIIX_ISA, XBCS, xbcs);
} else {
/* Configure PCIe ECAM base address */
x86_pci_write_config32(PCI_BDF(0, 0, 0), PCIEX_BAR,
CONFIG_PCIE_ECAM_BASE | BAR_EN);
}
/*
* QEMU emulated graphic card shows in the PCI configuration space with
* PCI vendor id and device id as an artificial pair 0x1234:0x1111.
* It is on PCI bus 0, function 0, but device number is not consistent
* for the two x86 targets it supports. For i440FX and PIIX chipset
* board, it shows as device 2, while for Q35 and ICH9 chipset board,
* it shows as device 1.
*/
vga = i440fx ? I440FX_VGA : Q35_VGA;
start = get_timer(0);
ret = pci_run_vga_bios(vga, NULL, PCI_ROM_USE_NATIVE);
debug("BIOS ran in %lums\n", get_timer(start));
return ret;
}
int lpc_init(struct pci_controller *hose, pci_dev_t dev)
{
const void *blob = gd->fdt_blob;
int node;
debug("pch: lpc_init\n");
pci_write_bar32(hose, dev, 0, 0);
pci_write_bar32(hose, dev, 1, 0xff800000);
pci_write_bar32(hose, dev, 2, 0xfec00000);
pci_write_bar32(hose, dev, 3, 0x800);
pci_write_bar32(hose, dev, 4, 0x900);
node = fdtdec_next_compatible(blob, 0, COMPAT_INTEL_PCH);
if (node < 0)
return -ENOENT;
/* Set the value for PCI command register. */
x86_pci_write_config16(dev, PCI_COMMAND, 0x000f);
/* IO APIC initialization. */
pch_enable_apic(dev);
pch_enable_serial_irqs(dev);
/* Setup the PIRQ. */
pch_pirq_init(blob, node, dev);
/* Setup power options. */
pch_power_options(blob, node, dev);
/* Initialize power management */
switch (pch_silicon_type()) {
case PCH_TYPE_CPT: /* CougarPoint */
cpt_pm_init(dev);
break;
case PCH_TYPE_PPT: /* PantherPoint */
ppt_pm_init(dev);
break;
default:
printf("Unknown Chipset: %#02x.%dx\n", PCI_DEV(dev),
PCI_FUNC(dev));
return -ENOSYS;
}
/* Initialize the real time clock. */
pch_rtc_init(dev);
/* Initialize the High Precision Event Timers, if present. */
enable_hpet();
/* Initialize Clock Gating */
enable_clock_gating(dev);
pch_disable_smm_only_flashing(dev);
#if CONFIG_HAVE_SMI_HANDLER
pch_lock_smm(dev);
#endif
pch_fixups(dev);
return 0;
}
static int pch_power_options(const void *blob, int node, pci_dev_t dev)
{
u8 reg8;
u16 reg16, pmbase;
u32 reg32;
const char *state;
int pwr_on;
int nmi_option;
int ret;
/*
* Which state do we want to goto after g3 (power restored)?
* 0 == S0 Full On
* 1 == S5 Soft Off
*
* If the option is not existent (Laptops), use Kconfig setting.
* TODO([email protected]): Make this configurable
*/
pwr_on = MAINBOARD_POWER_ON;
reg16 = x86_pci_read_config16(dev, GEN_PMCON_3);
reg16 &= 0xfffe;
switch (pwr_on) {
case MAINBOARD_POWER_OFF:
reg16 |= 1;
state = "off";
break;
case MAINBOARD_POWER_ON:
reg16 &= ~1;
state = "on";
break;
case MAINBOARD_POWER_KEEP:
reg16 &= ~1;
state = "state keep";
break;
default:
state = "undefined";
}
reg16 &= ~(3 << 4); /* SLP_S4# Assertion Stretch 4s */
reg16 |= (1 << 3); /* SLP_S4# Assertion Stretch Enable */
reg16 &= ~(1 << 10);
reg16 |= (1 << 11); /* SLP_S3# Min Assertion Width 50ms */
reg16 |= (1 << 12); /* Disable SLP stretch after SUS well */
x86_pci_write_config16(dev, GEN_PMCON_3, reg16);
debug("Set power %s after power failure.\n", state);
/* Set up NMI on errors. */
reg8 = inb(0x61);
reg8 &= 0x0f; /* Higher Nibble must be 0 */
reg8 &= ~(1 << 3); /* IOCHK# NMI Enable */
reg8 |= (1 << 2); /* PCI SERR# Disable for now */
outb(reg8, 0x61);
reg8 = inb(0x70);
/* TODO([email protected]): Make this configurable */
nmi_option = NMI_OFF;
if (nmi_option) {
debug("NMI sources enabled.\n");
reg8 &= ~(1 << 7); /* Set NMI. */
} else {
debug("NMI sources disabled.\n");
/* Can't mask NMI from PCI-E and NMI_NOW */
reg8 |= (1 << 7);
}
outb(reg8, 0x70);
/* Enable CPU_SLP# and Intel Speedstep, set SMI# rate down */
reg16 = x86_pci_read_config16(dev, GEN_PMCON_1);
reg16 &= ~(3 << 0); /* SMI# rate 1 minute */
reg16 &= ~(1 << 10); /* Disable BIOS_PCI_EXP_EN for native PME */
#if DEBUG_PERIODIC_SMIS
/* Set DEBUG_PERIODIC_SMIS in pch.h to debug using periodic SMIs */
reg16 |= (3 << 0); /* Periodic SMI every 8s */
#endif
x86_pci_write_config16(dev, GEN_PMCON_1, reg16);
/* Set the board's GPI routing. */
ret = pch_gpi_routing(blob, node, dev);
if (ret)
return ret;
pmbase = x86_pci_read_config16(dev, 0x40) & 0xfffe;
writel(pmbase + GPE0_EN, fdtdec_get_int(blob, node,
"intel,gpe0-enable", 0));
writew(pmbase + ALT_GP_SMI_EN, fdtdec_get_int(blob, node,
"intel,alt-gp-smi-enable", 0));
/* Set up power management block and determine sleep mode */
reg32 = inl(pmbase + 0x04); /* PM1_CNT */
reg32 &= ~(7 << 10); /* SLP_TYP */
reg32 |= (1 << 0); /* SCI_EN */
outl(reg32, pmbase + 0x04);
/* Clear magic status bits to prevent unexpected wake */
setbits_le32(RCB_REG(0x3310), (1 << 4) | (1 << 5) | (1 << 0));
clrbits_le32(RCB_REG(0x3f02), 0xf);
return 0;
}
