/*********************************************************************//**
* @brief Get Result conversion from A/D data register
* @param[in] channel number which want to read back the result
* @return Result of conversion
*********************************************************************/
uint32_t ADC_GetData(uint32_t channel)
{
uint32_t adc_value;
adc_value = *(uint32_t *)((&LPC_ADC->DR[0]) + channel);
return ADC_GDR_RESULT(adc_value);
}
/*********************************************************************//**
* @brief Get ADC Data from AD Global register
* @param[in] channel channel number
* @return Result of conversion
*
************************************************************************/
uint16_t ADC_GlobalGetData(void)
{
// alexk: CHECK_PARAM(PARAM_ADC_CHANNEL_SELECTION(channel));
//ADCx->ADGDR &= ~ADC_GDR_CH_MASK;
//ADCx->ADGDR |= ADC_GDR_CH(channel);
return (uint16_t)(ADC_GDR_RESULT(LPC_ADC->GDR));
}
/**
* @brief Get ADC Data from AD Global register
* @param[in] ADCx pointer to ADC
* @param[in] channel channel number
* @return Result of conversion
*
*********************************************************************/
uint16_t ADC_GlobalGetData(ADC_TypeDef *ADCx, uint8_t channel)
{
CHECK_PARAM(PARAM_ADCx(ADCx));
CHECK_PARAM(PARAM_ADC_CHANNEL_SELECTION(channel));
//ADCx->ADGDR &= ~ADC_GDR_CH_MASK;
//ADCx->ADGDR |= ADC_GDR_CH(channel);
return (uint16_t)(ADC_GDR_RESULT(ADCx->ADGDR));
}
/**
* @brief Get Result conversion from A/D data register
* @param[in] channel number which want to read back the result
* @return Result of conversion
*********************************************************************/
uint32_t ADC_GetData(uint32_t channel)
{
uint32_t adc_value;
CHECK_PARAM(PARAM_ADC_CHANNEL_SELECTION(channel));
adc_value = *(uint32_t *)((&ADC->ADDR0) + channel);
return ADC_GDR_RESULT(adc_value);
}
/*********************************************************************//**
* @brief c_entry: Main ADC program body
* @param[in] None
* @return None
**********************************************************************/
void c_entry(void)
{
volatile uint32_t tmp;
#if !__DMA_USED__
uint32_t adc_value;
#endif
uint8_t quit;
EXTI_InitTypeDef EXTICfg;
#if __DMA_USED__
GPDMA_Channel_CFG_Type GPDMACfg;
#endif
GPIO_Init();
/* Initialize debug via UART0
* – 115200bps
* – 8 data bit
* – No parity
* – 1 stop bit
* – No flow control
*/
debug_frmwrk_init();
// print welcome screen
print_menu();
/*
* Init ADC pin connect
* AD0.2 on P0.25
*/
PINSEL_ConfigPin(BRD_ADC_PREPARED_CH_PORT, BRD_ADC_PREPARED_CH_PIN, BRD_ADC_PREPARED_CH_FUNC_NO);
PINSEL_SetAnalogPinMode(BRD_ADC_PREPARED_CH_PORT,BRD_ADC_PREPARED_CH_PIN,ENABLE);
#ifdef LPC177x_8x_ADC_BURST_MULTI
/*
* Init ADC pin connect
* AD0.3 on P0.26
*/
PINSEL_ConfigPin(0, 26, 1);
PINSEL_SetAnalogPinMode(0,26,ENABLE);
#endif
/* Configuration for ADC:
* select: ADC channel 2
* ADC channel 3
* ADC conversion rate = 400KHz
*/
ADC_Init(LPC_ADC, 400000);
ADC_ChannelCmd(LPC_ADC,BRD_ADC_PREPARED_CHANNEL,ENABLE);
#ifdef LPC177x_8x_ADC_BURST_MULTI
ADC_ChannelCmd(LPC_ADC,_ADC_CHANNEL_n,ENABLE);
#endif
#ifdef LPC177x_8x_ADC_INJECT_TEST
//Config P2.10 as EINT0
PINSEL_ConfigPin(2,10,1);
EXTI_Init();
EXTICfg.EXTI_Line = EXTI_EINT0;
/* edge sensitive */
EXTICfg.EXTI_Mode = EXTI_MODE_EDGE_SENSITIVE;
EXTICfg.EXTI_polarity = EXTI_POLARITY_LOW_ACTIVE_OR_FALLING_EDGE;
EXTI_Config(&EXTICfg);
GPIO_SetDir(LED_PORT,LED_PIN,1);
GPIO_SetValue(LED_PORT,LED_PIN);
NVIC_EnableIRQ(EINT0_IRQn);
#endif
#if __DMA_USED__
/* Initialize GPDMA controller */
GPDMA_Init();
// Setup GPDMA channel --------------------------------
// channel 0
GPDMACfg.ChannelNum = 0;
// Source memory - unused
GPDMACfg.SrcMemAddr = 0;
// Destination memory
GPDMACfg.DstMemAddr = (uint32_t)s_buf;
// Transfer size
GPDMACfg.TransferSize = DMA_SIZE;
// Transfer width - unused
GPDMACfg.TransferWidth = 0;
// Transfer type
GPDMACfg.TransferType = GPDMA_TRANSFERTYPE_P2M;
// Source connection
GPDMACfg.SrcConn = GPDMA_CONN_ADC;
// Destination connection - unused
GPDMACfg.DstConn = 0;
// Linker List Item - unused
GPDMACfg.DMALLI = 0;
/* Enable GPDMA interrupt */
NVIC_EnableIRQ(DMA_IRQn);
while(1)
{
for(tmp = 0; tmp < 0x1000; tmp++);
/* Reset terminal counter */
Channel0_TC = 0;
/* Reset Error counter */
Channel0_Err = 0;
for(tmp = 0; tmp < DMA_SIZE; tmp++)
{
s_buf[tmp] = 0;
}
//Start burst conversion
ADC_BurstCmd(LPC_ADC,ENABLE);
GPDMA_Setup(&GPDMACfg);
// Enable GPDMA channel 1
GPDMA_ChannelCmd(0, ENABLE);
/* Wait for GPDMA processing complete */
while ((Channel0_TC == 0));
GPDMA_ChannelCmd(0, DISABLE);
for(tmp = 0; tmp < DMA_SIZE; tmp++)
{
if(s_buf[tmp] & ADC_GDR_DONE_FLAG)
{
_DBG("ADC value on channel "); _DBD(ADC_GDR_CH(s_buf[tmp])); _DBG(": ");
_DBD32(ADC_GDR_RESULT(s_buf[tmp]));_DBG_("");
}
}
if(_DG_NONBLOCK(&quit) &&
(quit == 'Q' || quit == 'q'))
break;
}
#else
//Start burst conversion
ADC_BurstCmd(LPC_ADC,ENABLE);
while(1)
{
adc_value = ADC_ChannelGetData(LPC_ADC,BRD_ADC_PREPARED_CHANNEL);
_DBG("ADC value on channel "); _DBD(BRD_ADC_PREPARED_CHANNEL); _DBG(": ");
_DBD32(adc_value);
_DBG_("");
#ifdef LPC177x_8x_ADC_BURST_MULTI
adc_value = ADC_ChannelGetData(LPC_ADC,_ADC_CHANNEL_n);
_DBG("ADC value on channel 3: ");
_DBD32(adc_value);
_DBG_("");
#endif
// Wait for a while
for(tmp = 0; tmp < 1500000; tmp++);
if(_DG_NONBLOCK(&quit) &&
(quit == 'Q' || quit == 'q'))
break;
}
#endif /*__DMA_USED__*/
_DBG_("Demo termination!!!");
ADC_DeInit(LPC_ADC);
GPIO_Deinit();
}
