void BSP_rtems_irq_mngt_init(unsigned cpuId)
{
int i;
/*
* connect all exception vectors needed
*/
ppc_exc_set_handler(ASM_EXT_VECTOR, C_dispatch_irq_handler);
ppc_exc_set_handler(ASM_BOOKE_DEC_VECTOR, C_dispatch_irq_handler);
/*
* setup interrupt handlers table
*/
for (i = 0;
i < BSP_IRQ_NUMBER;
i++) {
rtemsIrqTbl[i] = emptyIrq;
rtemsIrqTbl[i].name = i;
}
/*
* initialize interrupt management
*/
if (!BSP_rtems_irq_mngt_set(&initialConfig)) {
BSP_panic("Unable to initialize RTEMS interrupt Management!!! System locked\n");
}
}
/*
* This code assumes the exceptions management setup has already
* been done. We just need to replace the exceptions that will
* be handled like interrupt. On MPC7455 and many PPC processors
* this means the decrementer exception and the external exception.
*/
void BSP_rtems_irq_mng_init(unsigned cpuId)
{
rtems_raw_except_connect_data vectorDesc;
int i;
/*
* First initialize the Interrupt management hardware
*/
#ifdef TRACE_IRQ_INIT
printk("Initializing the interrupt controller of the GT64260\n");
#endif
#ifdef TRACE_IRQ_INIT
printk("Going to re-initialize the rtemsIrq table %d\n",BSP_IRQ_NUMBER);
#endif
/*
* Initialize Rtems management interrupt table
*/
/*
* re-init the rtemsIrq table
*/
for (i = 0; i < BSP_IRQ_NUMBER; i++) {
rtemsIrq[i] = defaultIrq;
rtemsIrq[i].name = i;
}
/*
* Init initial Interrupt management config
*/
initial_config.irqNb = BSP_IRQ_NUMBER;
initial_config.defaultEntry = defaultIrq;
initial_config.irqHdlTbl = rtemsIrq;
initial_config.irqBase = BSP_ASM_IRQ_VECTOR_BASE;
initial_config.irqPrioTbl = BSPirqPrioTable;
#ifdef TRACE_IRQ_INIT
printk("Going to setup irq mngt configuration\n");
#endif
if (!BSP_rtems_irq_mngt_set(&initial_config)) {
/*
* put something here that will show the failure...
*/
BSP_panic("Unable to initialize RTEMS interrupt Management!!! System locked\n");
}
#ifdef TRACE_IRQ_INIT
printk("Done setup irq mngt configuration\n");
#endif
#ifdef TRACE_IRQ_INIT
printk("RTEMS IRQ management is now operationnal\n");
#endif
}
/*
* This code assumes the exceptions management setup has already
* been done. We just need to replace the exceptions that will
* be handled like interrupt. On mcp750/mpc750 and many PPC processors
* this means the decrementer exception and the external exception.
*/
void BSP_rtems_irq_mng_init(unsigned cpuId)
{
int i;
/*
* First initialize the Interrupt management hardware
*/
#ifdef TRACE_IRQ_INIT
printk("Going to initialize openpic compliant device\n");
#endif
/* FIXME (t.s.): we should probably setup the EOI delay by
* passing a non-zero 'epic_freq' argument (frequency of the
* EPIC serial interface) but I don't know the value on this
* board (8245 SDRAM freq, IIRC)...
*/
openpic_init(1, mcp750_openpic_initpolarities, mcp750_openpic_initsenses, 0, 16, 0 /* epic_freq */);
#ifdef TRACE_IRQ_INIT
printk("Going to initialize the PCI/ISA bridge IRQ related setting (VIA 82C586)\n");
#endif
/*
* Initialize Rtems management interrupt table
*/
/*
* re-init the rtemsIrq table
*/
for (i = 0; i < BSP_IRQ_NUMBER; i++) {
rtemsIrq[i] = defaultIrq;
rtemsIrq[i].name = i;
}
/*
* Init initial Interrupt management config
*/
initial_config.irqNb = BSP_IRQ_NUMBER;
initial_config.defaultEntry = defaultIrq;
initial_config.irqHdlTbl = rtemsIrq;
initial_config.irqBase = BSP_LOWEST_OFFSET;
initial_config.irqPrioTbl = irqPrioTable;
printk("Call BSP_rtems_irq_mngt_set\n");
if (!BSP_rtems_irq_mngt_set(&initial_config)) {
/*
* put something here that will show the failure...
*/
BSP_panic("Unable to initialize RTEMS interrupt Management!!! System locked\n");
}
#ifdef TRACE_IRQ_INIT
printk("RTEMS IRQ management is now operationnal\n");
#endif
}
/*
* This code assumes the exceptions management setup has already
* been done. We just need to replace the exceptions that will
* be handled like interrupt. On mcp750/mpc750 and many PPC processors
* this means the decrementer exception and the external exception.
*/
void BSP_rtems_irq_mng_init(unsigned cpuId)
{
int i;
/*
* First initialize the Interrupt management hardware
*/
OpenPIC = (void*)PSIM.OpenPIC;
openpic_init(1,0,0,16,0,0);
/*
* Initialize Rtems management interrupt table
*/
/*
* re-init the rtemsIrq table
*/
for (i = 0; i < BSP_IRQ_NUMBER; i++) {
rtemsIrq[i] = defaultIrq;
rtemsIrq[i].name = i;
}
/*
* Init initial Interrupt management config
*/
initial_config.irqNb = BSP_IRQ_NUMBER;
initial_config.defaultEntry = defaultIrq;
initial_config.irqHdlTbl = rtemsIrq;
initial_config.irqBase = BSP_LOWEST_OFFSET;
initial_config.irqPrioTbl = irqPrioTable;
for (i = BSP_PCI_IRQ_LOWEST_OFFSET; i< BSP_PCI_IRQ_NUMBER; i++ ) {
irqPrioTable[i] = 8;
}
if (!BSP_rtems_irq_mngt_set(&initial_config)) {
/*
* put something here that will show the failure...
*/
BSP_panic(
"Unable to initialize RTEMS interrupt Management!!! System locked\n"
);
}
#ifdef TRACE_IRQ_INIT
printk("RTEMS IRQ management is now operationnal\n");
#endif
}
/*
* This code assumes the exceptions management setup has already
* been done. We just need to replace the exceptions that will
* be handled like interrupt. On mcp750/mpc750 and many PPC processors
* this means the decrementer exception and the external exception.
*/
void BSP_rtems_irq_mng_init(unsigned cpuId)
{
int i;
/*
* First initialize the Interrupt management hardware
*/
/*
* Initialize RTEMS management interrupt table
*/
/*
* re-init the rtemsIrq table
*/
for (i = 0; i < BSP_IRQ_NUMBER; i++) {
irqPrioTable[i] = 8;
rtemsIrq[i] = defaultIrq;
rtemsIrq[i].name = i;
#ifdef BSP_SHARED_HANDLER_SUPPORT
rtemsIrq[i].next_handler = NULL;
#endif
}
/*
* Init initial Interrupt management config
*/
initial_config.irqNb = BSP_IRQ_NUMBER;
initial_config.defaultEntry = defaultIrq;
initial_config.irqHdlTbl = rtemsIrq;
initial_config.irqBase = BSP_LOWEST_OFFSET;
initial_config.irqPrioTbl = irqPrioTable;
if (!BSP_rtems_irq_mngt_set(&initial_config)) {
/*
* put something here that will show the failure...
*/
BSP_panic("Unable to initialize RTEMS interrupt Management!!! System locked\n");
}
#ifdef TRACE_IRQ_INIT
printk("RTEMS IRQ management is now operational\n");
#endif
}
/*
* This code assumes the exceptions management setup has already
* been done. We just need to replace the exceptions that will
* be handled like interrupt. On mcp750/mpc750 and many PPC processors
* this means the decrementer exception and the external exception.
*/
void BSP_rtems_irq_mng_init(unsigned cpuId)
{
#if BSP_ISA_IRQ_NUMBER > 0 && !defined(mvme2100)
int known_cpi_isa_bridge = 0;
#endif
int i;
/*
* First initialize the Interrupt management hardware
*/
#if defined(mvme2100)
#ifdef TRACE_IRQ_INIT
printk("Going to initialize EPIC interrupt controller (openpic compliant)\n");
#endif
/* EPIC sources don't start at the regular place; define appropriate offset
* prior to initializing the PIC.
*/
openpic_init(1, mvme2100_openpic_initpolarities, mvme2100_openpic_initsenses, 16, 16, BSP_bus_frequency);
#else
#if BSP_PCI_IRQ_NUMBER > 0
#ifdef TRACE_IRQ_INIT
printk("Going to initialize raven interrupt controller (openpic compliant)\n");
#endif
openpic_init(1, mcp750_openpic_initpolarities, mcp750_openpic_initsenses, 0, 0, 0);
#ifdef TRACE_IRQ_INIT
printk("Going to initialize the PCI/ISA bridge IRQ related setting (VIA 82C586)\n");
#endif
#endif
#if BSP_ISA_IRQ_NUMBER > 0
if ( currentBoard == MESQUITE ) {
#ifndef qemu
VIA_isa_bridge_interrupts_setup();
#endif
known_cpi_isa_bridge = 1;
}
if ( currentBoard == MVME_2300 ) {
/* nothing to do for W83C553 bridge */
known_cpi_isa_bridge = 1;
}
if ( currentBoard == MTX_WO_PP || currentBoard == MTX_W_PP ) {
/* W83C554, don't to anything at the moment. gregm 11/6/2002 */
known_cpi_isa_bridge = 1;
}
if (!known_cpi_isa_bridge) {
printk("Please add code for PCI/ISA bridge init to libbsp/powerpc/shared/irq/irq_init.c\n");
printk("If your card works correctly please add a test and set known_cpi_isa_bridge to true\n");
printk("currentBoard = %i\n", currentBoard);
}
#ifdef TRACE_IRQ_INIT
printk("Going to initialize the ISA PC legacy IRQ management hardware\n");
#endif
BSP_i8259s_init();
#endif
#endif
/*
* Initialize RTEMS management interrupt table
*/
/*
* re-init the rtemsIrq table
*/
for (i = 0; i < BSP_IRQ_NUMBER; i++) {
rtemsIrq[i] = defaultIrq;
rtemsIrq[i].name = i;
}
/*
* Init initial Interrupt management config
*/
initial_config.irqNb = BSP_IRQ_NUMBER;
initial_config.defaultEntry = defaultIrq;
initial_config.irqHdlTbl = rtemsIrq;
initial_config.irqBase = BSP_LOWEST_OFFSET;
initial_config.irqPrioTbl = irqPrioTable;
if (!BSP_rtems_irq_mngt_set(&initial_config)) {
/*
* put something here that will show the failure...
*/
BSP_panic("Unable to initialize RTEMS interrupt Management!!! System locked\n");
}
#ifdef TRACE_IRQ_INIT
printk("RTEMS IRQ management is now operational\n");
#endif
}