/* Setup init condition */
static void test_setup(int on_ac)
{
const struct battery_info *bat_info = battery_get_info();
reset_mocks();
/* 50% of charge */
sb_write(SB_RELATIVE_STATE_OF_CHARGE, 50);
sb_write(SB_ABSOLUTE_STATE_OF_CHARGE, 50);
/* full charge capacity in mAh */
sb_write(SB_FULL_CHARGE_CAPACITY, 0xf000);
/* 25 degree Celsius */
sb_write(SB_TEMPERATURE, CELSIUS_TO_DECI_KELVIN(25));
/* battery pack voltage */
sb_write(SB_VOLTAGE, bat_info->voltage_normal);
/* desired charging voltage/current */
sb_write(SB_CHARGING_VOLTAGE, bat_info->voltage_max);
sb_write(SB_CHARGING_CURRENT, 4000);
/* battery pack current is positive when charging */
if (on_ac) {
sb_write(SB_CURRENT, 1000);
gpio_set_level(GPIO_AC_PRESENT, 1);
} else {
sb_write(SB_CURRENT, -100);
gpio_set_level(GPIO_AC_PRESENT, 0);
}
/* Reset the charger state to initial state */
charge_control(CHARGE_CONTROL_NORMAL);
/* Let things stabilize */
wait_charging_state();
}
static int test_high_temp_battery(void)
{
test_setup(1);
ccprintf("[CHARGING TEST] High battery temperature shutdown\n");
ev_clear(EC_HOST_EVENT_BATTERY_SHUTDOWN);
sb_write(SB_TEMPERATURE, CELSIUS_TO_DECI_KELVIN(90));
wait_charging_state();
TEST_ASSERT(ev_is_set(EC_HOST_EVENT_BATTERY_SHUTDOWN));
TEST_ASSERT(!is_shutdown);
sleep(CONFIG_BATTERY_CRITICAL_SHUTDOWN_TIMEOUT);
TEST_ASSERT(is_shutdown);
ccprintf("[CHARGING TEST] High battery temp S0->S5 hibernate\n");
mock_chipset_state = CHIPSET_STATE_SOFT_OFF;
wait_charging_state();
TEST_ASSERT(is_hibernated);
return EC_SUCCESS;
}
static int test_charge_state(void)
{
enum charge_state state;
uint32_t flags;
/* On AC */
test_setup(1);
ccprintf("[CHARGING TEST] AC on\n");
/* Detach battery, charging error */
ccprintf("[CHARGING TEST] Detach battery\n");
TEST_ASSERT(test_detach_i2c(I2C_PORT_BATTERY, BATTERY_ADDR) ==
EC_SUCCESS);
msleep(BATTERY_DETACH_DELAY);
state = wait_charging_state();
TEST_ASSERT(state == PWR_STATE_ERROR);
/* Attach battery again, charging */
ccprintf("[CHARGING TEST] Attach battery\n");
test_attach_i2c(I2C_PORT_BATTERY, BATTERY_ADDR);
/* And changing full capacity should trigger a host event */
ev_clear(EC_HOST_EVENT_BATTERY);
sb_write(SB_FULL_CHARGE_CAPACITY, 0xeff0);
state = wait_charging_state();
TEST_ASSERT(state == PWR_STATE_CHARGE);
TEST_ASSERT(ev_is_set(EC_HOST_EVENT_BATTERY));
/* Unplug AC, discharging at 1000mAh */
ccprintf("[CHARGING TEST] AC off\n");
gpio_set_level(GPIO_AC_PRESENT, 0);
sb_write(SB_CURRENT, -1000);
state = wait_charging_state();
TEST_ASSERT(state == PWR_STATE_DISCHARGE);
flags = charge_get_flags();
TEST_ASSERT(!(flags & CHARGE_FLAG_EXTERNAL_POWER));
TEST_ASSERT(!(flags & CHARGE_FLAG_FORCE_IDLE));
/* Discharging waaaay overtemp is ignored */
ccprintf("[CHARGING TEST] AC off, batt temp = 0xffff\n");
gpio_set_level(GPIO_AC_PRESENT, 0);
sb_write(SB_CURRENT, -1000);
state = wait_charging_state();
TEST_ASSERT(state == PWR_STATE_DISCHARGE);
sb_write(SB_TEMPERATURE, 0xffff);
state = wait_charging_state();
TEST_ASSERT(!is_shutdown);
TEST_ASSERT(state == PWR_STATE_DISCHARGE);
sb_write(SB_TEMPERATURE, CELSIUS_TO_DECI_KELVIN(40));
/* Discharging overtemp */
ccprintf("[CHARGING TEST] AC off, batt temp = 90 C\n");
gpio_set_level(GPIO_AC_PRESENT, 0);
sb_write(SB_CURRENT, -1000);
state = wait_charging_state();
TEST_ASSERT(state == PWR_STATE_DISCHARGE);
sb_write(SB_TEMPERATURE, CELSIUS_TO_DECI_KELVIN(90));
state = wait_charging_state();
TEST_ASSERT(is_shutdown);
TEST_ASSERT(state == PWR_STATE_DISCHARGE);
sb_write(SB_TEMPERATURE, CELSIUS_TO_DECI_KELVIN(40));
/* Force idle */
ccprintf("[CHARGING TEST] AC on, force idle\n");
gpio_set_level(GPIO_AC_PRESENT, 1);
sb_write(SB_CURRENT, 1000);
state = wait_charging_state();
TEST_ASSERT(state == PWR_STATE_CHARGE);
flags = charge_get_flags();
TEST_ASSERT(flags & CHARGE_FLAG_EXTERNAL_POWER);
TEST_ASSERT(!(flags & CHARGE_FLAG_FORCE_IDLE));
charge_control(CHARGE_CONTROL_IDLE);
state = wait_charging_state();
TEST_ASSERT(state == PWR_STATE_IDLE);
flags = charge_get_flags();
TEST_ASSERT(flags & CHARGE_FLAG_EXTERNAL_POWER);
TEST_ASSERT(flags & CHARGE_FLAG_FORCE_IDLE);
charge_control(CHARGE_CONTROL_NORMAL);
state = wait_charging_state();
TEST_ASSERT(state == PWR_STATE_CHARGE);
/* Force discharge */
ccprintf("[CHARGING TEST] AC on, force discharge\n");
gpio_set_level(GPIO_AC_PRESENT, 1);
sb_write(SB_CURRENT, 1000);
charge_control(CHARGE_CONTROL_DISCHARGE);
state = wait_charging_state();
TEST_ASSERT(state == PWR_STATE_IDLE);
TEST_ASSERT(is_force_discharge);
charge_control(CHARGE_CONTROL_NORMAL);
state = wait_charging_state();
TEST_ASSERT(state == PWR_STATE_CHARGE);
TEST_ASSERT(!is_force_discharge);
return EC_SUCCESS;
}
/* Main loop */
void charger_task(void)
{
int sleep_usec;
int need_static = 1;
const struct charger_info * const info = charger_get_info();
/* Get the battery-specific values */
batt_info = battery_get_info();
prev_ac = prev_charge = -1;
chg_ctl_mode = CHARGE_CONTROL_NORMAL;
shutdown_warning_time.val = 0UL;
battery_seems_to_be_dead = 0;
/*
* If system is not locked and we don't have a battery to live on,
* then use max input current limit so that we can pull as much power
* as needed.
*/
battery_get_params(&curr.batt);
prev_bp = curr.batt.is_present;
curr.desired_input_current = get_desired_input_current(prev_bp, info);
while (1) {
#ifdef CONFIG_SB_FIRMWARE_UPDATE
if (sb_fw_update_in_progress()) {
task_wait_event(CHARGE_MAX_SLEEP_USEC);
continue;
}
#endif
/* Let's see what's going on... */
curr.ts = get_time();
sleep_usec = 0;
problems_exist = 0;
curr.ac = extpower_is_present();
if (curr.ac != prev_ac) {
if (curr.ac) {
/*
* Some chargers are unpowered when the AC is
* off, so we'll reinitialize it when AC
* comes back and set the input current limit.
* Try again if it fails.
*/
int rv = charger_post_init();
if (rv != EC_SUCCESS) {
problem(PR_POST_INIT, rv);
} else {
if (curr.desired_input_current !=
CHARGE_CURRENT_UNINITIALIZED)
rv = charger_set_input_current(
curr.desired_input_current);
if (rv != EC_SUCCESS)
problem(PR_SET_INPUT_CURR, rv);
else
prev_ac = curr.ac;
}
} else {
/* Some things are only meaningful on AC */
chg_ctl_mode = CHARGE_CONTROL_NORMAL;
battery_seems_to_be_dead = 0;
prev_ac = curr.ac;
}
}
charger_get_params(&curr.chg);
battery_get_params(&curr.batt);
if (prev_bp != curr.batt.is_present) {
prev_bp = curr.batt.is_present;
/* Update battery info due to change of battery */
batt_info = battery_get_info();
need_static = 1;
curr.desired_input_current =
get_desired_input_current(prev_bp, info);
if (curr.desired_input_current !=
CHARGE_CURRENT_UNINITIALIZED)
charger_set_input_current(
curr.desired_input_current);
hook_notify(HOOK_BATTERY_SOC_CHANGE);
}
/*
* TODO(crosbug.com/p/27527). Sometimes the battery thinks its
* temperature is 6280C, which seems a bit high. Let's ignore
* anything above the boiling point of tungsten until this bug
* is fixed. If the battery is really that warm, we probably
* have more urgent problems.
*/
if (curr.batt.temperature > CELSIUS_TO_DECI_KELVIN(5660)) {
CPRINTS("ignoring ridiculous batt.temp of %dC",
DECI_KELVIN_TO_CELSIUS(curr.batt.temperature));
curr.batt.flags |= BATT_FLAG_BAD_TEMPERATURE;
}
/* If the battery thinks it's above 100%, don't believe it */
if (curr.batt.state_of_charge > 100) {
CPRINTS("ignoring ridiculous batt.soc of %d%%",
curr.batt.state_of_charge);
curr.batt.flags |= BATT_FLAG_BAD_STATE_OF_CHARGE;
}
/*
* Now decide what we want to do about it. We'll normally just
* pass along whatever the battery wants to the charger. Note
* that if battery_get_params() can't get valid values from the
* battery it uses (0, 0), which is probably safer than blindly
* applying power to a battery we can't talk to.
*/
curr.requested_voltage = curr.batt.desired_voltage;
curr.requested_current = curr.batt.desired_current;
/* If we *know* there's no battery, wait for one to appear. */
if (curr.batt.is_present == BP_NO) {
ASSERT(curr.ac); /* How are we running? */
curr.state = ST_IDLE;
curr.batt_is_charging = 0;
battery_was_removed = 1;
goto wait_for_it;
}
/*
* If we had trouble talking to the battery or the charger, we
* should probably do nothing for a bit, and if it doesn't get
* better then flag it as an error.
*/
if (curr.chg.flags & CHG_FLAG_BAD_ANY)
problem(PR_CHG_FLAGS, curr.chg.flags);
if (curr.batt.flags & BATT_FLAG_BAD_ANY)
problem(PR_BATT_FLAGS, curr.batt.flags);
/*
* If AC is present, check if input current is sufficient to
* actually charge battery.
*/
curr.batt_is_charging = curr.ac && (curr.batt.current >= 0);
/* Don't let the battery hurt itself. */
shutdown_on_critical_battery();
if (!curr.ac) {
curr.state = ST_DISCHARGE;
goto wait_for_it;
}
/* Okay, we're on AC and we should have a battery. */
/* Used for factory tests. */
if (chg_ctl_mode != CHARGE_CONTROL_NORMAL) {
curr.state = ST_IDLE;
goto wait_for_it;
}
/* If the battery is not responsive, try to wake it up. */
if (!(curr.batt.flags & BATT_FLAG_RESPONSIVE)) {
if (battery_seems_to_be_dead || battery_is_cut_off()) {
/* It's dead, do nothing */
curr.state = ST_IDLE;
curr.requested_voltage = 0;
curr.requested_current = 0;
} else if (curr.state == ST_PRECHARGE &&
(get_time().val > precharge_start_time.val +
PRECHARGE_TIMEOUT_US)) {
/* We've tried long enough, give up */
CPRINTS("battery seems to be dead");
battery_seems_to_be_dead = 1;
curr.state = ST_IDLE;
curr.requested_voltage = 0;
curr.requested_current = 0;
} else {
/* See if we can wake it up */
if (curr.state != ST_PRECHARGE) {
CPRINTS("try to wake battery");
precharge_start_time = get_time();
need_static = 1;
}
curr.state = ST_PRECHARGE;
curr.requested_voltage =
batt_info->voltage_max;
curr.requested_current =
batt_info->precharge_current;
}
goto wait_for_it;
} else {
/* The battery is responding. Yay. Try to use it. */
#ifdef CONFIG_BATTERY_REQUESTS_NIL_WHEN_DEAD
/*
* TODO (crosbug.com/p/29467): remove this workaround
* for dead battery that requests no voltage/current
*/
if (curr.requested_voltage == 0 &&
curr.requested_current == 0 &&
curr.batt.state_of_charge == 0) {
/* Battery is dead, give precharge current */
curr.requested_voltage =
batt_info->voltage_max;
curr.requested_current =
batt_info->precharge_current;
} else
#endif
#ifdef CONFIG_BATTERY_REVIVE_DISCONNECT
battery_seems_to_be_disconnected = 0;
if (curr.requested_voltage == 0 &&
curr.requested_current == 0 &&
battery_get_disconnect_state() ==
BATTERY_DISCONNECTED) {
/*
* Battery is in disconnect state. Apply a
* current to kick it out of this state.
*/
CPRINTS("found battery in disconnect state");
curr.requested_voltage =
batt_info->voltage_max;
curr.requested_current =
batt_info->precharge_current;
battery_seems_to_be_disconnected = 1;
} else
#endif
if (curr.state == ST_PRECHARGE ||
battery_seems_to_be_dead ||
battery_was_removed) {
CPRINTS("battery woke up");
/* Update the battery-specific values */
batt_info = battery_get_info();
need_static = 1;
}
battery_seems_to_be_dead = battery_was_removed = 0;
curr.state = ST_CHARGE;
}
/*
* TODO(crosbug.com/p/27643): Quit trying if charging too long
* without getting full (CONFIG_CHARGER_TIMEOUT_HOURS).
*/
wait_for_it:
#ifdef CONFIG_CHARGER_PROFILE_OVERRIDE
sleep_usec = charger_profile_override(&curr);
if (sleep_usec < 0)
problem(PR_CUSTOM, sleep_usec);
#endif
/* Keep the AP informed */
if (need_static)
need_static = update_static_battery_info();
/* Wait on the dynamic info until the static info is good. */
if (!need_static)
update_dynamic_battery_info();
notify_host_of_low_battery();
/* And the EC console */
is_full = calc_is_full();
if ((!(curr.batt.flags & BATT_FLAG_BAD_STATE_OF_CHARGE) &&
curr.batt.state_of_charge != prev_charge) ||
(is_full != prev_full)) {
show_charging_progress();
prev_charge = curr.batt.state_of_charge;
hook_notify(HOOK_BATTERY_SOC_CHANGE);
}
prev_full = is_full;
/* Turn charger off if it's not needed */
if (curr.state == ST_IDLE || curr.state == ST_DISCHARGE) {
curr.requested_voltage = 0;
curr.requested_current = 0;
}
/* Apply external limits */
if (curr.requested_current > user_current_limit)
curr.requested_current = user_current_limit;
/* Round to valid values */
curr.requested_voltage =
charger_closest_voltage(curr.requested_voltage);
curr.requested_current =
charger_closest_current(curr.requested_current);
/* Charger only accpets request when AC is on. */
if (curr.ac) {
/*
* Some batteries would wake up after cut-off if we keep
* charging it. Thus, we only charge when AC is on and
* battery is not cut off yet.
*/
if (battery_is_cut_off())
charge_request(0, 0);
/*
* As a safety feature, some chargers will stop
* charging if we don't communicate with it frequently
* enough. In manual mode, we'll just tell it what it
* knows.
*/
else if (manual_mode) {
charge_request(curr.chg.voltage,
curr.chg.current);
} else {
charge_request(curr.requested_voltage,
curr.requested_current);
}
} else {
charge_request(
charger_closest_voltage(
curr.batt.voltage + info->voltage_step), -1);
}
/* How long to sleep? */
if (problems_exist)
/* If there are errors, don't wait very long. */
sleep_usec = CHARGE_POLL_PERIOD_SHORT;
else if (sleep_usec <= 0) {
/* default values depend on the state */
if (curr.state == ST_IDLE ||
curr.state == ST_DISCHARGE) {
/* If AP is off, we can sleep a long time */
if (chipset_in_state(CHIPSET_STATE_ANY_OFF |
CHIPSET_STATE_SUSPEND))
sleep_usec =
CHARGE_POLL_PERIOD_VERY_LONG;
else
/* Discharging, not too urgent */
sleep_usec = CHARGE_POLL_PERIOD_LONG;
} else {
/* Charging, so pay closer attention */
sleep_usec = CHARGE_POLL_PERIOD_CHARGE;
}
}
/* Adjust for time spent in this loop */
sleep_usec -= (int)(get_time().val - curr.ts.val);
if (sleep_usec < CHARGE_MIN_SLEEP_USEC)
sleep_usec = CHARGE_MIN_SLEEP_USEC;
else if (sleep_usec > CHARGE_MAX_SLEEP_USEC)
sleep_usec = CHARGE_MAX_SLEEP_USEC;
task_wait_event(sleep_usec);
}
}
static int acpi_thermal_trips_update(struct acpi_thermal *tz, int flag)
{
acpi_status status = AE_OK;
unsigned long long tmp;
struct acpi_handle_list devices;
int valid = 0;
int i;
/* Critical Shutdown */
if (flag & ACPI_TRIPS_CRITICAL) {
status = acpi_evaluate_integer(tz->device->handle,
"_CRT", NULL, &tmp);
tz->trips.critical.temperature = tmp;
/*
* Treat freezing temperatures as invalid as well; some
* BIOSes return really low values and cause reboots at startup.
* Below zero (Celsius) values clearly aren't right for sure..
* ... so lets discard those as invalid.
*/
if (ACPI_FAILURE(status)) {
tz->trips.critical.flags.valid = 0;
ACPI_DEBUG_PRINT((ACPI_DB_INFO,
"No critical threshold\n"));
} else if (tmp <= 2732) {
pr_warn(FW_BUG "Invalid critical threshold (%llu)\n",
tmp);
tz->trips.critical.flags.valid = 0;
} else {
tz->trips.critical.flags.valid = 1;
ACPI_DEBUG_PRINT((ACPI_DB_INFO,
"Found critical threshold [%lu]\n",
tz->trips.critical.temperature));
}
if (tz->trips.critical.flags.valid == 1) {
if (crt == -1) {
tz->trips.critical.flags.valid = 0;
} else if (crt > 0) {
unsigned long crt_k = CELSIUS_TO_DECI_KELVIN(crt);
/*
* Allow override critical threshold
*/
if (crt_k > tz->trips.critical.temperature)
pr_warn(PREFIX "Critical threshold %d C\n",
crt);
tz->trips.critical.temperature = crt_k;
}
}
}
/* Critical Sleep (optional) */
if (flag & ACPI_TRIPS_HOT) {
status = acpi_evaluate_integer(tz->device->handle,
"_HOT", NULL, &tmp);
if (ACPI_FAILURE(status)) {
tz->trips.hot.flags.valid = 0;
ACPI_DEBUG_PRINT((ACPI_DB_INFO,
"No hot threshold\n"));
} else {
tz->trips.hot.temperature = tmp;
tz->trips.hot.flags.valid = 1;
ACPI_DEBUG_PRINT((ACPI_DB_INFO,
"Found hot threshold [%lu]\n",
tz->trips.hot.temperature));
}
}
/* Passive (optional) */
if (((flag & ACPI_TRIPS_PASSIVE) && tz->trips.passive.flags.valid) ||
(flag == ACPI_TRIPS_INIT)) {
valid = tz->trips.passive.flags.valid;
if (psv == -1) {
status = AE_SUPPORT;
} else if (psv > 0) {
tmp = CELSIUS_TO_DECI_KELVIN(psv);
status = AE_OK;
} else {
status = acpi_evaluate_integer(tz->device->handle,
"_PSV", NULL, &tmp);
}
if (ACPI_FAILURE(status))
tz->trips.passive.flags.valid = 0;
else {
tz->trips.passive.temperature = tmp;
tz->trips.passive.flags.valid = 1;
if (flag == ACPI_TRIPS_INIT) {
status = acpi_evaluate_integer(
tz->device->handle, "_TC1",
NULL, &tmp);
if (ACPI_FAILURE(status))
tz->trips.passive.flags.valid = 0;
else
tz->trips.passive.tc1 = tmp;
status = acpi_evaluate_integer(
tz->device->handle, "_TC2",
NULL, &tmp);
if (ACPI_FAILURE(status))
tz->trips.passive.flags.valid = 0;
else
tz->trips.passive.tc2 = tmp;
status = acpi_evaluate_integer(
tz->device->handle, "_TSP",
NULL, &tmp);
if (ACPI_FAILURE(status))
tz->trips.passive.flags.valid = 0;
else
tz->trips.passive.tsp = tmp;
}
}
}
if ((flag & ACPI_TRIPS_DEVICES) && tz->trips.passive.flags.valid) {
memset(&devices, 0, sizeof(struct acpi_handle_list));
status = acpi_evaluate_reference(tz->device->handle, "_PSL",
NULL, &devices);
if (ACPI_FAILURE(status)) {
pr_warn(PREFIX "Invalid passive threshold\n");
tz->trips.passive.flags.valid = 0;
}
else
tz->trips.passive.flags.valid = 1;
if (memcmp(&tz->trips.passive.devices, &devices,
sizeof(struct acpi_handle_list))) {
memcpy(&tz->trips.passive.devices, &devices,
sizeof(struct acpi_handle_list));
ACPI_THERMAL_TRIPS_EXCEPTION(flag, "device");
}
}
if ((flag & ACPI_TRIPS_PASSIVE) || (flag & ACPI_TRIPS_DEVICES)) {
if (valid != tz->trips.passive.flags.valid)
ACPI_THERMAL_TRIPS_EXCEPTION(flag, "state");
}
/* Active (optional) */
for (i = 0; i < ACPI_THERMAL_MAX_ACTIVE; i++) {
char name[5] = { '_', 'A', 'C', ('0' + i), '\0' };
valid = tz->trips.active[i].flags.valid;
if (act == -1)
break; /* disable all active trip points */
if ((flag == ACPI_TRIPS_INIT) || ((flag & ACPI_TRIPS_ACTIVE) &&
tz->trips.active[i].flags.valid)) {
status = acpi_evaluate_integer(tz->device->handle,
name, NULL, &tmp);
if (ACPI_FAILURE(status)) {
tz->trips.active[i].flags.valid = 0;
if (i == 0)
break;
if (act <= 0)
break;
if (i == 1)
tz->trips.active[0].temperature =
CELSIUS_TO_DECI_KELVIN(act);
else
/*
* Don't allow override higher than
* the next higher trip point
*/
tz->trips.active[i - 1].temperature =
(tz->trips.active[i - 2].temperature <
CELSIUS_TO_DECI_KELVIN(act) ?
tz->trips.active[i - 2].temperature :
CELSIUS_TO_DECI_KELVIN(act));
break;
} else {
tz->trips.active[i].temperature = tmp;
tz->trips.active[i].flags.valid = 1;
}
}
name[2] = 'L';
if ((flag & ACPI_TRIPS_DEVICES) && tz->trips.active[i].flags.valid ) {
memset(&devices, 0, sizeof(struct acpi_handle_list));
status = acpi_evaluate_reference(tz->device->handle,
name, NULL, &devices);
if (ACPI_FAILURE(status)) {
pr_warn(PREFIX "Invalid active%d threshold\n",
i);
tz->trips.active[i].flags.valid = 0;
}
else
tz->trips.active[i].flags.valid = 1;
if (memcmp(&tz->trips.active[i].devices, &devices,
sizeof(struct acpi_handle_list))) {
memcpy(&tz->trips.active[i].devices, &devices,
sizeof(struct acpi_handle_list));
ACPI_THERMAL_TRIPS_EXCEPTION(flag, "device");
}
}
if ((flag & ACPI_TRIPS_ACTIVE) || (flag & ACPI_TRIPS_DEVICES))
if (valid != tz->trips.active[i].flags.valid)
ACPI_THERMAL_TRIPS_EXCEPTION(flag, "state");
if (!tz->trips.active[i].flags.valid)
break;
}
if ((flag & ACPI_TRIPS_DEVICES)
&& acpi_has_method(tz->device->handle, "_TZD")) {
memset(&devices, 0, sizeof(devices));
status = acpi_evaluate_reference(tz->device->handle, "_TZD",
NULL, &devices);
if (ACPI_SUCCESS(status)
&& memcmp(&tz->devices, &devices, sizeof(devices))) {
tz->devices = devices;
ACPI_THERMAL_TRIPS_EXCEPTION(flag, "device");
}
}
return 0;
}
