void vParTestInitialise( void )
{
/* Configure the bits used to flash LED's on port 1 as output. */
GPIO_Config(GPIO1, partstALL_LEDs, GPIO_OUT_OD);
}
int main(void) {
FRESULT fresult;
NVIC_InitTypeDef nvicStructure;
SystemInit();
GPIO_Config();
SPI_Config();
/*
for(i1=0;i1<TABLE_SIZE;i1++){
buffer[0][i1] = 4*i1;
}
for(i1=0;i1<TABLE_SIZE;i1++){
buffer[1][i1] = 2047*sin(currentPhase)+2047;
currentPhase += phaseIncrement;
}
*/
/* Configure LED3 and LED4 on STM32L100C-Discovery */
STM_EVAL_LEDInit(LED3);
STM_EVAL_LEDInit(LED4);
/* SysTick end of count event each 1ms */
//RCC_GetClocksFreq(&RCC_Clocks);
// SysTick_Config(RCC_Clocks.HCLK_Frequency / 1000);
//delay_init(72);//
delay_init(16);
Lcd_Init2();
Lcd_Clear2(BLACK);
/* RTC configuration */
//RTC_Config();
RTC_Config32768Internal();
/* Configure RTC alarm A register to generate 8 interrupts per 1 Second */
RTC_AlarmConfig();
tft_puts(45, 20, "12:00", white, black);
RCC_ClocksTypeDef RCC_Clocks;
/* Initialize User_Button on STM32L100C-Discovery */
STM_EVAL_PBInit(BUTTON_MODE, BUTTON_MODE_GPIO);
STM_EVAL_PBInit(BUTTON_UP, BUTTON_MODE_GPIO);
STM_EVAL_PBInit(BUTTON_DOWN, BUTTON_MODE_GPIO);
//STM_EVAL_PBInit(BUTTON_MODE, BUTTON_MODE_EXTI);
/* SysTick end of count event each 1ms */
// RCC_GetClocksFreq(&RCC_Clocks);
// SysTick_Config(RCC_Clocks.HCLK_Frequency / 1000);
/*************************/
//TIM_TimeBaseInitTypeDef TIM_TimeBaseStructure;
RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM2, ENABLE);
nvicStructure.NVIC_IRQChannel = TIM2_IRQn;
nvicStructure.NVIC_IRQChannelPreemptionPriority = 0;
nvicStructure.NVIC_IRQChannelSubPriority = 1;
nvicStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&nvicStructure);
TIM_TimeBaseInitTypeDef timerInitStructure;
timerInitStructure.TIM_Prescaler = 3200; //32 MHz/3200 = 10000
timerInitStructure.TIM_CounterMode = TIM_CounterMode_Up;
//timerInitStructure.TIM_Period = 3332;
timerInitStructure.TIM_Period = 100; //10 000/100 = 100 Hz - sampling frequency of buttons
timerInitStructure.TIM_ClockDivision = TIM_CKD_DIV1;
//timerInitStructure.TIM_RepetitionCounter = 0;
TIM_TimeBaseInit(TIM2, &timerInitStructure);
TIM_ITConfig(TIM2, TIM_IT_Update, ENABLE);
TIM_Cmd(TIM2, ENABLE);
/*************************/
//GPIO_PinAFConfig(GPIOA, GPIO_PinSource4, GPIO_AF_SPI1);
GPIO_PinAFConfig(GPIOA, GPIO_PinSource5, GPIO_AF_SPI1);
GPIO_PinAFConfig(GPIOA, GPIO_PinSource6, GPIO_AF_SPI1);
GPIO_PinAFConfig(GPIOA, GPIO_PinSource7, GPIO_AF_SPI1);
fresult = f_mount(&g_sFatFs, "0:0", 1);
//LCD_BMP("kasia.bmp");
//Gui_DrawFont_GBK24_bk(20,120, BLUE, WHITE, "1234 abcd");
//playWav("rct3.wav"); // fsamp 22050 Hz, 8bit
/* tests */
//playWav("m8m.wav"); // fsamp 44100 Hz, 8 bit
//playWav("bj8.wav"); // fsamp 44100 Hz, 8 bit
//playWav("im16.wav"); // fsamp 44100 Hz, 16 bit
//playWavFromIntMemory(rooster3);
displayDate();
while (1) {
if (updated) {
displayTime();
updated = false;
if(updateDate){
updateAndDisplayDate();
updateDate = false;
}
}
}
}
/**
* @brief Main program.
* @param None
* @retval None
*/
int main(void)
{
/* STM32F4xx HAL library initialization:
- Configure the Flash prefetch, instruction and Data caches
- Configure the Systick to generate an interrupt each 1 msec
- Set NVIC Group Priority to 4
- Global MSP (MCU Support Package) initialization
*/
HAL_Init();
/* Configure the system clock to have a system clock = 180 Mhz */
SystemClock_Config();
/* Init the STemWin GUI Library */
BSP_SDRAM_Init(); /* Initializes the SDRAM device */
__CRC_CLK_ENABLE(); /* Enable the CRC Module */
// __PWR_CLK_ENABLE();
// HAL_PWR_EnableBkUpAccess();
// __HAL_RCC_LSE_CONFIG(RCC_LSE_BYPASS);
// __HAL_RCC_RTC_ENABLE();
/*##-1- Configure the RTC peripheral #######################################*/
RtcHandle.Instance = RTC;
/* Configure RTC prescaler and RTC data registers */
/* RTC configured as follow:
- Hour Format = Format 24
- Asynch Prediv = Value according to source clock
- Synch Prediv = Value according to source clock
- OutPut = Output Disable
- OutPutPolarity = High Polarity
- OutPutType = Open Drain */
RtcHandle.Init.HourFormat = RTC_HOURFORMAT_24;
RtcHandle.Init.AsynchPrediv = RTC_ASYNCH_PREDIV;
RtcHandle.Init.SynchPrediv = RTC_SYNCH_PREDIV;
RtcHandle.Init.OutPut = RTC_OUTPUT_DISABLE;
RtcHandle.Init.OutPutPolarity = RTC_OUTPUT_POLARITY_HIGH;
RtcHandle.Init.OutPutType = RTC_OUTPUT_TYPE_OPENDRAIN;
if(HAL_RTC_Init(&RtcHandle) != HAL_OK)
{
/* Initialization Error */
Error_Handler();
}
/*##-2- Check if Data stored in BackUp register0: No Need to reconfigure RTC#*/
/* Read the BackUp Register 0 Data */
if(HAL_RTCEx_BKUPRead(&RtcHandle, RTC_BKP_DR0) != 0x32F2)
{
/* Configure RTC Calendar */
RTC_CalendarConfig();
}
else
{
/* Check if the Power On Reset flag is set */
if(__HAL_RCC_GET_FLAG(RCC_FLAG_PORRST) != RESET)
{
}
/* Check if Pin Reset flag is set */
if(__HAL_RCC_GET_FLAG(RCC_FLAG_PINRST) != RESET)
{
}
/* Clear Reset Flag */
__HAL_RCC_CLEAR_RESET_FLAGS();
}
GUI_Init();
//GUI_Initialized = 1;
GPIO_Config();
if(HAL_RTCEx_BKUPRead(&RtcHandle, RTC_BKP_DR1) ==0)
{
HAL_RTCEx_BKUPWrite(&RtcHandle,RTC_BKP_DR1,600);
}
Time3Enable(HAL_RTCEx_BKUPRead(&RtcHandle, RTC_BKP_DR1));
/* Activate the use of memory device feature */
WM_SetCreateFlags(WM_CF_MEMDEV);
os_sys_init (init);
}
BOOL
xMBPortSerialInit( UCHAR ucPort, ULONG ulBaudRate, UCHAR ucDataBits, eMBParity eParity )
{
BOOL xResult = TRUE;
UARTParity_TypeDef eUARTParity;
UARTMode_TypeDef eUARTMode;
(void)ucPort;
switch ( eParity )
{
case MB_PAR_EVEN:
eUARTParity = UART_EVEN_PARITY;
break;
case MB_PAR_ODD:
eUARTParity = UART_ODD_PARITY;
break;
case MB_PAR_NONE:
eUARTParity = UART_NO_PARITY;
break;
}
switch ( ucDataBits )
{
case 7:
if( eParity == MB_PAR_NONE )
{
/* not supported by our hardware. */
xResult = FALSE;
}
else
{
eUARTMode = UARTM_7D_P;
}
break;
case 8:
if( eParity == MB_PAR_NONE )
{
eUARTMode = UARTM_8D;
}
else
{
eUARTMode = UARTM_8D_P;
}
break;
default:
xResult = FALSE;
}
if( xResult != FALSE )
{
/* Setup the UART port pins. */
GPIO_Config( MB_UART_TX_PORT, 1 << MB_UART_TX_PIN, GPIO_AF_PP );
GPIO_Config( MB_UART_RX_PORT, 1 << MB_UART_RX_PIN, GPIO_IN_TRI_CMOS );
/* Configure the UART. */
UART_OnOffConfig( MB_UART_DEV, ENABLE );
UART_FifoConfig( MB_UART_DEV, DISABLE );
UART_FifoReset( MB_UART_DEV, UART_RxFIFO );
UART_FifoReset( MB_UART_DEV, UART_TxFIFO );
UART_LoopBackConfig( MB_UART_DEV, DISABLE );
UART_Config( MB_UART_DEV, ulBaudRate, eUARTParity, UART_1_StopBits,
eUARTMode );
UART_RxConfig( UART0, ENABLE );
vMBPortSerialEnable( FALSE, FALSE );
/* Configure the IEC for the UART interrupts. */
EIC_IRQChannelPriorityConfig( MB_UART_IRQ_CH, MB_IRQ_PRIORITY );
EIC_IRQChannelConfig( MB_UART_IRQ_CH, ENABLE );
}
return xResult;
}
int main( void )
{
u32 i = 0;
u8 ReadBuf[128] = {0};
u8 TrData[8][32] = {0};
u8 WriteData[50] = "ABCDEFG";
SystemInit();
GPIO_Config();
RS232_Config();
LED_R = 1;
LED_G = 1;
// SD Card Init Info
RS232_SendStr(USART3, (u8*)" \r\n");
RS232_SendStr(USART3, (u8*)"----------------------\r\n");
RS232_SendStr(USART3, (u8*)"----------------------\r\n");
RS232_SendStr(USART3, (u8*)" SDIO SD FatFs demo\r\n");
RS232_SendStr(USART3, (u8*)"----------------------\r\n");
RS232_SendStr(USART3, (u8*)"----------------------\r\n\r\n");
RS232_SendStr(USART3, (u8*)" SD Init ... ");
while(SD_Init() != SD_OK) {
RS232_SendStr(USART3, (u8*)"Failed!!\r\n");
while(1) {
LED_R = ~LED_R;
Delay_100ms(2);
}
}
RS232_SendStr(USART3, (u8*)"OK!!\r\n\r\n");
RS232_SendStr(USART3, (u8*)"-----SD Init Info-----\r\n");
RS232_SendStr(USART3, (u8*)" Capacity : ");
NumToChar(Type_D, 5, TrData[0], SDCardInfo.CardCapacity>>20);
RS232_SendStr(USART3, TrData[0]);
RS232_SendStr(USART3, (u8*)" MB\r\n");
RS232_SendStr(USART3, (u8*)" CardBlockSize : ");
NumToChar(Type_D, 5, TrData[1], SDCardInfo.CardBlockSize);
RS232_SendStr(USART3, TrData[1]);
RS232_SendStr(USART3, (u8*)"\r\n");
RS232_SendStr(USART3, (u8*)" CardType : ");
NumToChar(Type_D, 5, TrData[2], SDCardInfo.CardType);
RS232_SendStr(USART3, TrData[2]);
RS232_SendStr(USART3, (u8*)"\r\n");
RS232_SendStr(USART3, (u8*)" RCA : ");
NumToChar(Type_D, 5, TrData[3], SDCardInfo.RCA);
RS232_SendStr(USART3, TrData[3]);
RS232_SendStr(USART3, (u8*)"\r\n");
RS232_SendStr(USART3, (u8*)"----------------------\r\n");
RS232_SendStr(USART3, (u8*)"\r\n");
// Wait
while(KEY != 1){
LED_G = ~LED_G;
Delay_100ms(2);
}
// Read Directory File
RS232_SendStr(USART3, (u8*)"----------------------\r\n");
RS232_SendStr(USART3, (u8*)" SD_Card Read Directory File\r\n");
RS232_SendStr(USART3, (u8*)"----------------------\r\n\r\n");
res = f_mount(&FatFs, "", 1);
res = f_opendir(&dirs, "0:/");
res = f_readdir(&dirs, &finfo);
while(res!= FR_OK) {
RS232_SendStr(USART3, (u8*)" FatFs failed!!\r\n");
while(1) {
LED_R = ~LED_R;
Delay_100ms(2);
}
}
RS232_SendStr(USART3, (u8*)" File name : \r\n");
while(finfo.fname[0]) {
f_readdir(&dirs, &finfo);
if(!finfo.fname[0])
break;
RS232_SendStr(USART3, (u8*)" ... ");
RS232_SendStr(USART3, (u8*)finfo.fname);
RS232_SendStr(USART3, (u8*)"\r\n");
}
// Wait
while(KEY != 1){
LED_G = ~LED_G;
Delay_100ms(2);
}
// Write File
RS232_SendStr(USART3, (u8*)" f_open ... ");
res = f_open(&file,"SDCard_K.txt", FA_OPEN_ALWAYS | FA_READ | FA_WRITE);
if(res==FR_OK)
RS232_SendStr(USART3, (u8*)"OK!!\r\n");
else
RS232_SendStr(USART3, (u8*)"failed!!\r\n");
RS232_SendStr(USART3, (u8*)" f_write ... ");
res = f_write(&file, WriteData, 20, (UINT *)&i);
if(res==FR_OK)
RS232_SendStr(USART3, (u8*)"OK!!\r\n");
else
RS232_SendStr(USART3, (u8*)"failed!!\r\n");
file.fptr = 0;
RS232_SendStr(USART3, (u8*)" f_read ... ");
res = f_read(&file, ReadBuf, 100, (UINT *)&i);
if(res==FR_OK)
RS232_SendStr(USART3, (u8*)"OK!!\r\n");
else
RS232_SendStr(USART3, (u8*)"failed!!\r\n");
f_close(&file);
RS232_SendStr(USART3, ReadBuf);
while(1) {
LED_G = ~LED_G;
Delay_100ms(2);
}
}
