void lcd_begin_frame()
{
uint8_t flags = vram.flags;
uint8_t mode = vram.mode;
lcd_window_x = 0;
lcd_window_y = vram.first_line;
/*
* Wake up the LCD controller, if necessary.
*/
if (!lcd_is_awake) {
lcd_is_awake = 1;
// First, we take the LCD controller out of reset.
// Then we fully initialize it. We turn on the backlight
// after both initialization is complete and the first
// frame has finished rendering.
CTRL_PORT = CTRL_IDLE & ~CTRL_LCD_DCX;
CTRL_PORT = (CTRL_IDLE & ~CTRL_LCD_DCX) | CTRL_FLASH_LAT2; // Enter reset
lcd_reset_delay();
CTRL_PORT = CTRL_IDLE;
CTRL_PORT = CTRL_IDLE | CTRL_FLASH_LAT2; // Exit reset
// Controller initialization
lcd_cmd_table(lcd_setup_table);
#ifdef LCD_MODEL_TIANMA_HX8353
lcd_lut_init();
#endif
}
LCD_WRITE_BEGIN();
// Set addressing mode
LCD_CMD_MODE();
LCD_BYTE(LCD_CMD_MADCTR);
LCD_DATA_MODE();
LCD_BYTE(LCD_MADCTR_NORMAL ^ (flags & LCD_MADCTR_VRAM));
// Set row/column addressing, and start RAMWR.
lcd_address_and_write();
LCD_WRITE_END();
// Vertical sync
#ifdef HAVE_LCD_TE
if (flags & _SYS_VF_SYNC)
while (!CTRL_LCD_TE);
#endif
}
void lcd_lut_init()
{
/*
* The HX8353 seems to boot up with a totally bogus color LUT.
* So, we need to set it ourselves.
*/
LCD_WRITE_BEGIN();
LCD_CMD_MODE();
LCD_BYTE(LCD_CMD_COLOR_LUT);
LCD_DATA_MODE();
lcd_lut_32(); // Red
lcd_lut_64(); // Green
lcd_lut_32(); // Blue
// It's okay to return in write mode.
}
/*
**
** low level routine to send a byte value
** to the LCD controller control register.
** entry argument is the data to output
** and the controller to use
** 1: IC 1, 2: IC 2, 3: both ICs
**
*/
void lcd_out_ctl(const unsigned char cmd, const unsigned char ncontr)
{ LCD_CMD_MODE();
LCDDATAPORT = cmd;
lcd_strobe_e(ncontr);
}
void lcd_address_and_write(void)
{
/*
* Change the row/column address, and start a RAMWR command.
*
* Assumes we're already set up for writing to the LCD.
* Leaves with the bus in data mode.
*
* In the case that HAVE_GRAM_PANEL_MISMATCH is defined,
* we must calculate the appropriate values for CASET and RASET
* based on the current VRAM flags configuration as follows:
*
* x_offset = (flags & LCD_MADCTR_MX) ? LCD_X_RIGHT_MARGIN : LCD_X_LEFT_MARGIN
* y_offset = (flags & LCD_MADCTR_MY) ? LCD_Y_BOTTOM_MARGIN : LCD_Y_TOP_MARGIN
* if (flags & LCD_MADCTR_MV) {
* col_offset = y_offset
* row_offset = x_offset
* } else {
* col_offset = x_offset
* row_offset = y_offset
* }
*
* Some graphics modes constrain the registers we can use
* to implement this - we can only touch b, r0 and r1,
* because of the requirements in vm_stamp_pixel(),
* by way of vm_fb32_pixel(). Otherwise, we'd be happy
* to implement this in C.
*/
#ifdef HAVE_GRAM_PANEL_MISMATCH
__asm
push acc
push dpl
push dph
; vram.flags in a
mov dptr, #_SYS_VA_FLAGS
movx a, @dptr
; select y_margin based on LCD_MADCTR_MY and save in b
jnb acc.7, 1$ ; flags & LCD_MADCTR_MY
mov b, #LCD_Y_BOTTOM_MARGIN
sjmp 2$
1$:
mov b, #LCD_Y_TOP_MARGIN
2$:
; col_offset in r1 and row_offset in r0, based on LCD_MADCTR_MV.
; XXX: because the X margins are both the same for the Santek,
; we shortcut the test of LCD_MADCTR_MX, since currently
; more code space is required to enable this test.
jnb acc.5, 3$ ; flags & LCD_MADCTR_MV
mov r1, b
mov r0, #LCD_X_RIGHT_MARGIN
sjmp 4$
3$:
mov r1, #LCD_X_LEFT_MARGIN
mov r0, b
4$:
ASM_LCD_CMD_MODE();
ASM_LCD_BYTE(#LCD_CMD_CASET);
ASM_LCD_DATA_MODE();
ASM_LCD_BYTE(#0x0);
mov a, _lcd_window_x
add a, r1
ASM_LCD_BYTE(a);
ASM_LCD_BYTE(#0x0);
mov a, #(LCD_WIDTH - 1)
add a, r1
ASM_LCD_BYTE(a);
ASM_LCD_CMD_MODE();
ASM_LCD_BYTE(#LCD_CMD_RASET);
ASM_LCD_DATA_MODE();
ASM_LCD_BYTE(#0x0);
mov a, _lcd_window_y
add a, r0
ASM_LCD_BYTE(a);
ASM_LCD_BYTE(#0x0);
mov a, #(LCD_HEIGHT - 1)
add a, r0
ASM_LCD_BYTE(a);
; assumption: dptr and a are not touched below
pop dph
pop dpl
pop acc
__endasm;
#else
LCD_CMD_MODE();
LCD_BYTE(LCD_CMD_CASET);
LCD_DATA_MODE();
LCD_BYTE(0);
LCD_BYTE((lcd_window_x));
LCD_BYTE(0);
LCD_BYTE((LCD_WIDTH - 1));
LCD_CMD_MODE();
LCD_BYTE(LCD_CMD_RASET);
LCD_DATA_MODE();
LCD_BYTE(0);
LCD_BYTE((lcd_window_y));
LCD_BYTE(0);
LCD_BYTE((LCD_HEIGHT - 1));
#endif
/*
* Start writing (RAMWR command).
*
* We have to do this particular command -> data transition
* somewhat gingerly, since the Truly LCD is really picky. If we
* transition from command to data while the write strobe is low,
* it will falsely detect that as an additional byte-write that we
* didn't intend.
*
* This paranoia is unnecessary but harmless on the Giantplus LCD.
*/
LCD_CMD_MODE();
LCD_BYTE(LCD_CMD_NOP);
ADDR_PORT = 1;
LCD_BYTE(LCD_CMD_RAMWR);
LCD_DATA_MODE();
}
