int main()
{
uint8 ch; /* Data sent on the serial port */
uint8 count = 0u; /* Initializing the count value */
uint8 pos = 0u;
CyGlobalIntEnable;
isr_1_Start(); /* Initializing the ISR */
UART_1_Start(); /* Enabling the UART */
LCD_Char_1_Start(); /* Enabling the LCD */
for(ch = START_CHAR_VALUE; ch <= END_CHAR_VALUE; ch++)
{
UART_1_WriteTxData(ch); /* Sending the data */
count++;
if(count % LCD_NUM_COLUMNS == 0u) /* If the count value reaches the count 16 start from first location */
{
pos = 0u; /* resets the count value */
LCD_Char_1_WriteControl(LCD_Char_1_CLEAR_DISPLAY); /* Display will be cleared when reached count value 16 */
}
LCD_Char_1_Position(0u, pos++); /* LCD position to the count++ */
LCD_Char_1_PutChar(ch); /* print the value in the LCD */
LCD_Char_1_Position(1u, 0u);
LCD_Char_1_PrintInt8(count); /* prints the count in the LCD */
CyDelay(200u);
}
for(;;) {}
}
/*******************************************************************************
* 初始化函数
********************************************************************************/
void init()
{
CyGlobalIntEnable; //全局中断开启
ADC_DelSig_1_Start(); /* 配置并开启ADC */
ADC_DelSig_1_StartConvert(); /* 开始进行转换 */
Uart_Rx_ISR_StartEx(RxInterruptHandler); /* 开启 Uart Rx 中断 并连接到 RxInterruptHandler */
Uart_Tx_ISR_StartEx(TxInterruptHandler); /* 开启 Uart Tx 并连接到 TxInterruptHandler */
UART_Start(); /* 开启 UART */
Uart_Rx_ISR_1_StartEx(Rx_1_InterruptHandler); /* 开启 Uart Rx 中断 并连接到 RxInterruptHandler */
Uart_Tx_ISR_1_StartEx(Tx_1_InterruptHandler); /* 开启 Uart Tx 并连接到 TxInterruptHandler */
UART_1_Start(); /* 开启 UART1 */
Uart_Rx_ISR_2_StartEx(Rx_1_InterruptHandler); /* 开启 Uart Rx 中断 并连接到 RxInterruptHandler */
Uart_Tx_ISR_2_StartEx(Tx_1_InterruptHandler); /* 开启 Uart Tx 并连接到 TxInterruptHandler */
UART_2_Start(); /* 开启 UART2 */
Timer_ISR_StartEx(TimerInterruptHandler); /* 开启 Timer 中断并连接到 TimerInterruptHandler */
Timer_Start(); /* 开启定时器 */
LCD_Char_1_Start(); /* 初始化并清除LCD */
//LCD_Char_1_PrintString("init");
}
void main(){
UART_1_Start();
/* choose when we receive interrupts from tx and rx */
UART_1_SetTxInterruptMode(UART_1_TX_STS_COMPLETE);
UART_1_SetRxInterruptMode(UART_1_RX_STS_FIFO_NOTEMPTY);
CyGlobalIntEnable;
UART_1_ClearTxBuffer();
UART_1_ClearRxBuffer();
LCD_Char_1_Start();
LCD_Char_1_Position(0,0);
/* initialize our source data to index */
int j;
for(j = 0; j < DATA_SIZE; ++j){
sourceData[j] = j;
}
/* enable our interrupt routines */
isr_1_StartEx(tx_int);
isr_2_StartEx(rx_int);
/* idle loop until we finish our transmission */
while(!rx_done){}
int k;
int errors = 0;
/* data validation */
for(k = 0; k < DATA_SIZE; ++k)
if(sourceData[k] != receiveData[k]) ++errors;
/* print errors to lcd */
LCD_Char_1_PrintString("errors: ");
LCD_Char_1_PrintNumber(errors);
LCD_Char_1_Position(1,0);
LCD_Char_1_PrintString("tx:");
LCD_Char_1_PrintNumber(tx_cnt);
LCD_Char_1_PrintString(" rx:");
LCD_Char_1_PrintNumber(rx_cnt);
for(;;){
}
}
void main(){
/* initialize UART */
UART_1_Start();
/* disable interrupts */
UART_1_DisableRxInt();
UART_1_DisableTxInt();
UART_1_ClearTxBuffer();
UART_1_ClearRxBuffer();
LCD_Char_1_Start();
LCD_Char_1_Position(0,0);
/* initialize or source array */
int j;
for(j = 0; j < DATA_SIZE; ++j){
sourceData[j] = j;
}
/* loop to transmit all 4096 bytes of our source array */
int i;
for(i = 0; i < DATA_SIZE; ++i){
UART_1_WriteTxData(sourceData[i]);
/* we check the receiver FIFO to see when we get the data */
while(UART_1_ReadRxStatus() != UART_1_RX_STS_FIFO_NOTEMPTY){}
/* if FIFO is not empty, save the data */
receiveData[i] = UART_1_ReadRxData();
}
int k;
int errors = 0;
/* loop through received data to verify it */
for(k = 0; k < DATA_SIZE; ++k)
if(sourceData[k] != receiveData[k]) ++errors;
/* print errors */
LCD_Char_1_PrintString("errors: ");
LCD_Char_1_PrintNumber(errors);
for(;;){
}
}
/*******************************************************************************
* Function Name: main
********************************************************************************
*
* Summary:
* Main function performs following functions:
* 1: Initializes the LCD
* 2: Get the temperature of the Die
* 3: Print the Die Temperature value in LCD
* 4: Print the Status value in the LCD
*
* Parameters:
* None.
*
* Return:
* None.
*
*******************************************************************************/
int main()
{
cystatus Status;
int16 temperature;
/* Initializing the LCD */
LCD_Char_1_Start();
while(1)
{
/* Providing some delay */
CyDelay(50);
/* Reading the Die Temperature value */
Status = DieTemp_1_GetTemp(&temperature);
/* Displaying the Die Temperature value on the LCD */
LCD_Char_1_Position(0u, 0u);
LCD_Char_1_PrintString("Temp = ");
if (temperature >= 0)
{
LCD_Char_1_PrintString("+");
}
else
{
/* If the temperature value is negative, display "-" sign and make value positive */
LCD_Char_1_PrintString("-");
temperature = (uint16)(~temperature + 1u);
}
LCD_Char_1_PrintNumber((uint16) (temperature));
LCD_Char_1_PrintString(" ");
LCD_Char_1_PutChar(LCD_Char_1_CUSTOM_7);
LCD_Char_1_PrintString("C");
/* Displaying the status value on the LCD */
LCD_Char_1_Position(1u, 0u);
LCD_Char_1_PrintString("Status = ");
LCD_Char_1_PrintInt8((uint8) Status);
}
}
/*main*/
void main(void)
{
/*Preliminary parts not important*/
LCD_Char_1_Start();
ADC_DelSig_1_Start();
ADC_DelSig_1_StartConvert();
Configure_DMA();
isr_1_StartEx(Buffer_complete);
isr_2_StartEx(LPF_buffer_complete);
ADC_DelSig_1_SetCoherency(ADC_DelSig_1_COHER_MID);
Filter_SetDalign(Filter_STAGEA_DALIGN,Filter_ENABLED);
Filter_SetDalign(Filter_HOLDA_DALIGN,Filter_ENABLED);
Filter_SetCoherency(Filter_STAGEA_COHER,Filter_KEY_MID);
Filter_SetCoherency(Filter_HOLDA_COHER,Filter_KEY_MID);
Filter_SetCoherency(Filter_CHANNEL_A,Filter_KEY_MID);
Filter_SetDalign(Filter_STAGEB_DALIGN,Filter_ENABLED);
Filter_SetDalign(Filter_HOLDB_DALIGN,Filter_ENABLED);
Filter_SetCoherency(Filter_STAGEB_COHER,Filter_KEY_MID);
Filter_SetCoherency(Filter_HOLDB_COHER,Filter_KEY_MID);
Filter_SetCoherency(Filter_CHANNEL_B,Filter_KEY_MID);
CyGlobalIntEnable;
Filter_Start();
/*Writes ADC values to ADC_samples array*/
while(1){
if (isr_BC_flag==1){
arm_cfft_q15(&arm_cfft_sR_q15_len256, Buffer_samples, 0, 1);
arm_cmplx_mag_q15(Buffer_samples, magoutput, fftlength);
CyDmaChEnable(DMA_2_Chan, 1);
isr_BC_flag=0;
isr_1_ClearPending();
}
}
}
void main()
{
CYGlobalIntEnable; /* Enable global interrupts */
ADC_DelSig_1_Start();/* Configure and power up ADC */
LCD_Char_1_Start(); /* Initialize and clear the LCD */
/* Move the cursor to Row 0 Column 0 */
LCD_Char_1_Position(ROW_0,COLUMN_0);
/* Print Label for the pot voltage raw count */
LCD_Char_1_PrintString("TEMP NOW: C");
LCD_Char_1_Position(ROW_1,COLUMN_0);
LCD_Char_1_PrintString("TEMP SET: C");
ADC_DelSig_1_StartConvert(); /* Force ADC to initiate a conversion */
/* Start capsense and initialize baselines and enable scan */
CapSense_Start();
CapSense_InitializeAllBaselines();
CapSense_ScanEnabledWidgets();
/* CyGlobalIntEnable; */ /* Uncomment this line to enable global interrupts. */
//Start the pwm;
PWM_1_Start();
for(;;)
{
/* If scanning is completed update the baseline count and check if sensor is active */
while(CapSense_IsBusy());
/* Update baseline for all the sensors */
CapSense_UpdateEnabledBaselines();
CapSense_ScanEnabledWidgets();
/* Test if button widget is active */
stateB_1 = CapSense_CheckIsWidgetActive(CapSense_BUTTON0__BTN);
stateB_2 = CapSense_CheckIsWidgetActive(CapSense_BUTTON1__BTN);
/* Wait for end of conversion */
ADC_DelSig_1_IsEndConversion(ADC_DelSig_1_WAIT_FOR_RESULT);
/* Get converted result */
voltageRawCount = ADC_DelSig_1_GetResult16();
//Change voltageRawCount to Temperature;
temp = voltageRawCount / 3.870 * 0.1017 + 0.5;
cold = (9999 - (temp > temp_set ? temp - temp_set : 0) * 50);
if(cold < 1000)
cold = 1000;
if(cold > 9999)
cold = 9999;
//Change the pwm;
PWM_1_WriteCompare(cold);
/* Set range limit */
if (temp > 0x7FFF)
{
temp = 0;
}
else
{
/* Continue on */
}
if(show < 10)
{
show++;
}
else
{
show = 0;
UpdateDisplay(temp, 0); /* Print result on LCD */
UpdateButtonState(stateB_1, stateB_2);
}
}
}