/** Task to set the configuration of the attached device after it has been enumerated, and to read and process
* HID reports from the device and display the results onto the board LEDs.
*/
void Mouse_HID_Task(void)
{
uint8_t ErrorCode;
/* Switch to determine what user-application handled host state the host state machine is in */
switch (USB_HostState)
{
case HOST_STATE_Addressed:
puts_P(PSTR("Getting Config Data.\r\n"));
/* Get and process the configuration descriptor data */
if ((ErrorCode = ProcessConfigurationDescriptor()) != SuccessfulConfigRead)
{
if (ErrorCode == ControlError)
puts_P(PSTR(ESC_FG_RED "Control Error (Get Configuration).\r\n"));
else
puts_P(PSTR(ESC_FG_RED "Invalid Device.\r\n"));
printf_P(PSTR(" -- Error Code: %d\r\n" ESC_FG_WHITE), ErrorCode);
/* Indicate error status */
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
/* Wait until USB device disconnected */
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
break;
}
/* Set the device configuration to the first configuration (rarely do devices use multiple configurations) */
if ((ErrorCode = USB_Host_SetDeviceConfiguration(1)) != HOST_SENDCONTROL_Successful)
{
printf_P(PSTR(ESC_FG_RED "Control Error (Set Configuration).\r\n"
" -- Error Code: %d\r\n" ESC_FG_WHITE), ErrorCode);
/* Indicate error status */
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
/* Wait until USB device disconnected */
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
break;
}
/* HID class request to set the mouse protocol to the Boot Protocol */
USB_ControlRequest = (USB_Request_Header_t)
{
.bmRequestType = (REQDIR_HOSTTODEVICE | REQTYPE_CLASS | REQREC_INTERFACE),
.bRequest = HID_REQ_SetProtocol,
.wValue = 0,
.wIndex = 0,
.wLength = 0,
};
/* Select the control pipe for the request transfer */
Pipe_SelectPipe(PIPE_CONTROLPIPE);
/* Send the request, display error and wait for device detach if request fails */
if ((ErrorCode = USB_Host_SendControlRequest(NULL)) != HOST_SENDCONTROL_Successful)
{
printf_P(PSTR(ESC_FG_RED "Control Error (Set Protocol).\r\n"
" -- Error Code: %d\r\n" ESC_FG_WHITE), ErrorCode);
/* Indicate error status */
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
/* Wait until USB device disconnected */
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
break;
}
puts_P(PSTR("Mouse Enumerated.\r\n"));
USB_HostState = HOST_STATE_Configured;
break;
case HOST_STATE_Configured:
/* If a report has been received, read and process it */
ReadNextReport();
break;
}
}
/** Event handler for the USB_Connect event. This indicates that the device is enumerating via the status LEDs and
* starts the library USB task to begin the enumeration and USB management process.
*/
void EVENT_USB_Device_Connect(void)
{
LEDs_SetAllLEDs(LEDMASK_USB_ENUMERATING);
}
/** Event handler for the library USB Configuration Changed event. */
void EVENT_USB_Device_ConfigurationChanged(void)
{
LEDs_SetAllLEDs(LEDMASK_USB_READY);
if (!MIDI_Device_ConfigureEndpoints(&Keyboard_MIDI_Interface))
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
}
/** Event handler for the USB_DeviceUnattached event. This indicates that a device has been removed from the host, and
* stops the library USB task management process.
*/
void EVENT_USB_Host_DeviceUnattached(void)
{
puts_P(PSTR("\r\nDevice Unattached.\r\n"));
LEDs_SetAllLEDs(LEDMASK_USB_NOTREADY);
}
/** Event handler for the USB_Disconnect event. This indicates that the device is no longer connected to a host via
* the status LEDs and stops the USB management task.
*/
void EVENT_USB_Device_Disconnect(void)
{
/* Indicate USB not ready */
LEDs_SetAllLEDs(LEDMASK_USB_NOTREADY);
}
/** Event handler for the USB_DeviceEnumerationComplete event. This indicates that a device has been successfully
* enumerated by the host and is now ready to be used by the application.
*/
void EVENT_USB_Host_DeviceEnumerationComplete(void)
{
LEDs_SetAllLEDs(LEDMASK_USB_READY);
}
/** Event handler for the USB_DeviceUnattached event. This indicates that a device has been removed from the host, and
* stops the library USB task management process.
*/
void EVENT_USB_Host_DeviceUnattached(void)
{
puts_P(PSTR(ESC_FG_GREEN "\r\nDevice Unattached.\r\n" ESC_FG_WHITE));
LEDs_SetAllLEDs(LEDMASK_USB_NOTREADY);
}
/** Main program entry point. This routine configures the hardware required by the application, then
* enters a loop to run the application tasks in sequence.
*/
int main(void)
{
SetupHardware();
puts_P(PSTR(ESC_FG_CYAN "CDC Host Demo running.\r\n" ESC_FG_WHITE));
LEDs_SetAllLEDs(LEDMASK_USB_NOTREADY);
sei();
for (;;)
{
switch (USB_HostState)
{
case HOST_STATE_Addressed:
LEDs_SetAllLEDs(LEDMASK_USB_ENUMERATING);
uint16_t ConfigDescriptorSize;
uint8_t ConfigDescriptorData[512];
if (USB_Host_GetDeviceConfigDescriptor(1, &ConfigDescriptorSize, ConfigDescriptorData,
sizeof(ConfigDescriptorData)) != HOST_GETCONFIG_Successful)
{
puts_P(PSTR("Error Retrieving Configuration Descriptor.\r\n"));
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
break;
}
if (CDC_Host_ConfigurePipes(&VirtualSerial_CDC_Interface,
ConfigDescriptorSize, ConfigDescriptorData) != CDC_ENUMERROR_NoError)
{
puts_P(PSTR("Attached Device Not a Valid CDC Class Device.\r\n"));
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
break;
}
if (USB_Host_SetDeviceConfiguration(1) != HOST_SENDCONTROL_Successful)
{
puts_P(PSTR("Error Setting Device Configuration.\r\n"));
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
break;
}
puts_P(PSTR("CDC Device Enumerated.\r\n"));
LEDs_SetAllLEDs(LEDMASK_USB_READY);
USB_HostState = HOST_STATE_Configured;
break;
case HOST_STATE_Configured:
if (CDC_Host_BytesReceived(&VirtualSerial_CDC_Interface))
{
/* Echo received bytes from the attached device through the USART */
int16_t ReceivedByte = CDC_Host_ReceiveByte(&VirtualSerial_CDC_Interface);
if (!(ReceivedByte < 0))
putchar(ReceivedByte);
}
break;
}
CDC_Host_USBTask(&VirtualSerial_CDC_Interface);
USB_USBTask();
}
}
/** Main program entry point. This routine configures the hardware required by the application, then
* enters a loop to run the application tasks in sequence.
*/
int main(void)
{
SetupHardware();
puts_P(PSTR(ESC_FG_CYAN "Still Image Host Demo running.\r\n" ESC_FG_WHITE));
LEDs_SetAllLEDs(LEDMASK_USB_NOTREADY);
sei();
for (;;)
{
switch (USB_HostState)
{
case HOST_STATE_Addressed:
LEDs_SetAllLEDs(LEDMASK_USB_ENUMERATING);
uint16_t ConfigDescriptorSize;
uint8_t ConfigDescriptorData[512];
if (USB_Host_GetDeviceConfigDescriptor(1, &ConfigDescriptorSize, ConfigDescriptorData,
sizeof(ConfigDescriptorData)) != HOST_GETCONFIG_Successful)
{
puts_P(PSTR("Error Retrieving Configuration Descriptor.\r\n"));
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
break;
}
if (SImage_Host_ConfigurePipes(&DigitalCamera_SI_Interface,
ConfigDescriptorSize, ConfigDescriptorData) != SI_ENUMERROR_NoError)
{
puts_P(PSTR("Attached Device Not a Valid Still Image Class Device.\r\n"));
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
break;
}
if (USB_Host_SetDeviceConfiguration(1) != HOST_SENDCONTROL_Successful)
{
puts_P(PSTR("Error Setting Device Configuration.\r\n"));
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
break;
}
puts_P(PSTR("Still Image Device Enumerated.\r\n"));
LEDs_SetAllLEDs(LEDMASK_USB_READY);
USB_HostState = HOST_STATE_Configured;
break;
case HOST_STATE_Configured:
puts_P(PSTR("Opening Session...\r\n"));
if (SImage_Host_OpenSession(&DigitalCamera_SI_Interface) != PIPE_RWSTREAM_NoError)
{
puts_P(PSTR("Could not open PIMA session.\r\n"));
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
break;
}
puts_P(PSTR("Turning off Device...\r\n"));
SImage_Host_SendCommand(&DigitalCamera_SI_Interface, 0x1013, 0, NULL);
if (SImage_Host_ReceiveResponse(&DigitalCamera_SI_Interface))
{
puts_P(PSTR("Could not turn off device.\r\n"));
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
break;
}
puts_P(PSTR("Device Off.\r\n"));
puts_P(PSTR("Closing Session...\r\n"));
if (SImage_Host_CloseSession(&DigitalCamera_SI_Interface) != PIPE_RWSTREAM_NoError)
{
puts_P(PSTR("Could not close PIMA session.\r\n"));
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
break;
}
LEDs_SetAllLEDs(LEDMASK_USB_READY);
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
break;
}
SImage_Host_USBTask(&DigitalCamera_SI_Interface);
USB_USBTask();
}
}
/** Task to manage the Mass Storage interface, reading in Command Block Wrappers from the host, processing the SCSI commands they
* contain, and returning Command Status Wrappers back to the host to indicate the success or failure of the last issued command.
*/
void MassStorage_Task(void)
{
/* Device must be connected and configured for the task to run */
if (USB_DeviceState != DEVICE_STATE_Configured)
return;
/* Select the Data Out Endpoint */
Endpoint_SelectEndpoint(MASS_STORAGE_OUT_EPNUM);
/* Check to see if a command from the host has been issued */
if (Endpoint_IsReadWriteAllowed())
{
/* Indicate busy */
LEDs_SetAllLEDs(LEDMASK_USB_BUSY);
/* Process sent command block from the host */
if (ReadInCommandBlock())
{
/* Check direction of command, select Data IN endpoint if data is from the device */
if (CommandBlock.Flags & COMMAND_DIRECTION_DATA_IN)
Endpoint_SelectEndpoint(MASS_STORAGE_IN_EPNUM);
/* Decode the received SCSI command, set returned status code */
CommandStatus.Status = SCSI_DecodeSCSICommand() ? Command_Pass : Command_Fail;
/* Load in the CBW tag into the CSW to link them together */
CommandStatus.Tag = CommandBlock.Tag;
/* Load in the data residue counter into the CSW */
CommandStatus.DataTransferResidue = CommandBlock.DataTransferLength;
/* Stall the selected data pipe if command failed (if data is still to be transferred) */
if ((CommandStatus.Status == Command_Fail) && (CommandStatus.DataTransferResidue))
Endpoint_StallTransaction();
/* Return command status block to the host */
ReturnCommandStatus();
/* Indicate ready */
LEDs_SetAllLEDs(LEDMASK_USB_READY);
}
else
{
/* Indicate error reading in the command block from the host */
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
}
}
/* Check if a Mass Storage Reset occurred */
if (IsMassStoreReset)
{
/* Reset the data endpoint banks */
Endpoint_ResetFIFO(MASS_STORAGE_OUT_EPNUM);
Endpoint_ResetFIFO(MASS_STORAGE_IN_EPNUM);
Endpoint_SelectEndpoint(MASS_STORAGE_OUT_EPNUM);
Endpoint_ClearStall();
Endpoint_ResetDataToggle();
Endpoint_SelectEndpoint(MASS_STORAGE_IN_EPNUM);
Endpoint_ClearStall();
Endpoint_ResetDataToggle();
/* Clear the abort transfer flag */
IsMassStoreReset = false;
}
}
/** Main program entry point. This routine configures the hardware required by the application, then
* enters a loop to run the application tasks in sequence.
*/
int main(void)
{
SetupHardware();
puts_P(PSTR(ESC_FG_CYAN "Mouse Host Demo running.\r\n" ESC_FG_WHITE));
sei();
LEDs_SetAllLEDs(LEDMASK_USB_NOTREADY);
for (;;)
{
switch (USB_HostState)
{
case HOST_STATE_Addressed:
LEDs_SetAllLEDs(LEDMASK_USB_ENUMERATING);
uint16_t ConfigDescriptorSize;
uint8_t ConfigDescriptorData[512];
if (USB_Host_GetDeviceConfigDescriptor(1, &ConfigDescriptorSize, ConfigDescriptorData,
sizeof(ConfigDescriptorData)) != HOST_GETCONFIG_Successful)
{
puts_P(PSTR("Error Retrieving Configuration Descriptor.\r\n"));
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
break;
}
if (HID_Host_ConfigurePipes(&Mouse_HID_Interface,
ConfigDescriptorSize, ConfigDescriptorData) != HID_ENUMERROR_NoError)
{
puts_P(PSTR("Attached Device Not a Valid Mouse.\r\n"));
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
break;
}
if (USB_Host_SetDeviceConfiguration(1) != HOST_SENDCONTROL_Successful)
{
puts_P(PSTR("Error Setting Device Configuration.\r\n"));
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
break;
}
if (HID_Host_SetReportProtocol(&Mouse_HID_Interface) != 0)
{
puts_P(PSTR("Error Setting Report Protocol Mode or Not a Valid Mouse.\r\n"));
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
break;
}
puts_P(PSTR("Mouse Enumerated.\r\n"));
LEDs_SetAllLEDs(LEDMASK_USB_READY);
USB_HostState = HOST_STATE_Configured;
break;
case HOST_STATE_Configured:
if (HID_Host_IsReportReceived(&Mouse_HID_Interface))
{
uint8_t MouseReport[Mouse_HID_Interface.State.LargestReportSize];
HID_Host_ReceiveReport(&Mouse_HID_Interface, &MouseReport);
uint8_t LEDMask = LEDS_NO_LEDS;
for (uint8_t ReportNumber = 0; ReportNumber < HIDReportInfo.TotalReportItems; ReportNumber++)
{
HID_ReportItem_t* ReportItem = &HIDReportInfo.ReportItems[ReportNumber];
/* Update the report item value if it is contained within the current report */
if (!(USB_GetHIDReportItemInfo(MouseReport, ReportItem)))
continue;
/* Determine what report item is being tested, process updated value as needed */
if ((ReportItem->Attributes.Usage.Page == USAGE_PAGE_BUTTON) &&
(ReportItem->ItemType == HID_REPORT_ITEM_In))
{
if (ReportItem->Value)
LEDMask = LEDS_ALL_LEDS;
}
else if ((ReportItem->Attributes.Usage.Page == USAGE_PAGE_GENERIC_DCTRL) &&
(ReportItem->Attributes.Usage.Usage == USAGE_SCROLL_WHEEL) &&
(ReportItem->ItemType == HID_REPORT_ITEM_In))
{
int16_t WheelDelta = HID_ALIGN_DATA(ReportItem, int16_t);
if (WheelDelta)
LEDMask = (LEDS_LED1 | LEDS_LED2 | ((WheelDelta > 0) ? LEDS_LED3 : LEDS_LED4));
}
else if ((ReportItem->Attributes.Usage.Page == USAGE_PAGE_GENERIC_DCTRL) &&
((ReportItem->Attributes.Usage.Usage == USAGE_X) ||
(ReportItem->Attributes.Usage.Usage == USAGE_Y)) &&
(ReportItem->ItemType == HID_REPORT_ITEM_In))
{
int16_t DeltaMovement = HID_ALIGN_DATA(ReportItem, int16_t);
if (DeltaMovement)
{
if (ReportItem->Attributes.Usage.Usage == USAGE_X)
LEDMask |= ((DeltaMovement > 0) ? LEDS_LED1 : LEDS_LED2);
else
LEDMask |= ((DeltaMovement > 0) ? LEDS_LED3 : LEDS_LED4);
}
}
}
LEDs_SetAllLEDs(LEDMask);
}
break;
}
HID_Host_USBTask(&Mouse_HID_Interface);
USB_USBTask();
}
}
/** Task to handle the generation of MIDI note change events in response to presses of the board joystick, and send them
* to the host.
*/
void MIDI_Task(void)
{
static uint8_t PrevJoystickStatus;
/* Device must be connected and configured for the task to run */
if (USB_DeviceState != DEVICE_STATE_Configured)
return;
Endpoint_SelectEndpoint(MIDI_STREAM_IN_EPADDR);
if (Endpoint_IsINReady())
{
uint8_t MIDICommand = 0;
uint8_t MIDIPitch;
uint8_t JoystickStatus = Joystick_GetStatus();
uint8_t JoystickChanges = (JoystickStatus ^ PrevJoystickStatus);
/* Get board button status - if pressed use channel 10 (percussion), otherwise use channel 1 */
uint8_t Channel = ((Buttons_GetStatus() & BUTTONS_BUTTON1) ? MIDI_CHANNEL(10) : MIDI_CHANNEL(1));
if (JoystickChanges & JOY_LEFT)
{
MIDICommand = ((JoystickStatus & JOY_LEFT)? MIDI_COMMAND_NOTE_ON : MIDI_COMMAND_NOTE_OFF);
MIDIPitch = 0x3C;
}
if (JoystickChanges & JOY_UP)
{
MIDICommand = ((JoystickStatus & JOY_UP)? MIDI_COMMAND_NOTE_ON : MIDI_COMMAND_NOTE_OFF);
MIDIPitch = 0x3D;
}
if (JoystickChanges & JOY_RIGHT)
{
MIDICommand = ((JoystickStatus & JOY_RIGHT)? MIDI_COMMAND_NOTE_ON : MIDI_COMMAND_NOTE_OFF);
MIDIPitch = 0x3E;
}
if (JoystickChanges & JOY_DOWN)
{
MIDICommand = ((JoystickStatus & JOY_DOWN)? MIDI_COMMAND_NOTE_ON : MIDI_COMMAND_NOTE_OFF);
MIDIPitch = 0x3F;
}
if (JoystickChanges & JOY_PRESS)
{
MIDICommand = ((JoystickStatus & JOY_PRESS)? MIDI_COMMAND_NOTE_ON : MIDI_COMMAND_NOTE_OFF);
MIDIPitch = 0x3B;
}
/* Check if a MIDI command is to be sent */
if (MIDICommand)
{
MIDI_EventPacket_t MIDIEvent = (MIDI_EventPacket_t)
{
.Event = MIDI_EVENT(0, MIDICommand),
.Data1 = MIDICommand | Channel,
.Data2 = MIDIPitch,
.Data3 = MIDI_STANDARD_VELOCITY,
};
/* Write the MIDI event packet to the endpoint */
Endpoint_Write_Stream_LE(&MIDIEvent, sizeof(MIDIEvent), NULL);
/* Send the data in the endpoint to the host */
Endpoint_ClearIN();
}
/* Save previous joystick value for next joystick change detection */
PrevJoystickStatus = JoystickStatus;
}
/* Select the MIDI OUT stream */
Endpoint_SelectEndpoint(MIDI_STREAM_OUT_EPADDR);
/* Check if a MIDI command has been received */
if (Endpoint_IsOUTReceived())
{
MIDI_EventPacket_t MIDIEvent;
/* Read the MIDI event packet from the endpoint */
Endpoint_Read_Stream_LE(&MIDIEvent, sizeof(MIDIEvent), NULL);
/* Check to see if the sent command is a note on message with a non-zero velocity */
if ((MIDIEvent.Event == MIDI_EVENT(0, MIDI_COMMAND_NOTE_ON)) && (MIDIEvent.Data3 > 0))
{
/* Change LEDs depending on the pitch of the sent note */
LEDs_SetAllLEDs(MIDIEvent.Data2 > 64 ? LEDS_LED1 : LEDS_LED2);
}
else
{
/* Turn off all LEDs in response to non Note On messages */
LEDs_SetAllLEDs(LEDS_NO_LEDS);
}
/* If the endpoint is now empty, clear the bank */
if (!(Endpoint_BytesInEndpoint()))
{
/* Clear the endpoint ready for new packet */
Endpoint_ClearOUT();
}
}
}
/** Event handler for the USB_DeviceEnumerationFailed event. This indicates that a problem occurred while
* enumerating an attached USB device.
*/
void EVENT_USB_Host_DeviceEnumerationFailed(const uint8_t ErrorCode,
const uint8_t SubErrorCode)
{
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
}
/** Main program entry point. This routine contains the overall program flow, including initial
* setup of all components and the main program loop.
*/
int main(void)
{
MIDI_EventPacket_t midiEvent;
struct {
uint8_t command;
uint8_t channel;
uint8_t data2;
uint8_t data3;
} midiMsg;
int ind;
int led1_ticks = 0;
int led2_ticks = 0;
SetupHardware();
RingBuffer_InitBuffer(&USBtoUSART_Buffer);
RingBuffer_InitBuffer(&USARTtoUSB_Buffer);
LEDs_SetAllLEDs(LEDMASK_USB_NOTREADY);
sei();
for (;;) {
RingBuff_Count_t BufferCount = RingBuffer_GetCount(&USARTtoUSB_Buffer);
/* See if we have a message yet */
if (BufferCount >= 4) {
/* Read in the message from the serial buffer */
for (ind=0; ind<4; ind++) {
((uint8_t *)&midiMsg)[ind] = RingBuffer_Remove(&USARTtoUSB_Buffer);
}
/* Build a midi event to send via USB */
midiEvent.CableNumber = 0;
midiEvent.Command = midiMsg.command >> 4;
midiEvent.Data1 = (midiMsg.command & 0xF0) | ((midiMsg.channel-1) & 0x0F);
midiEvent.Data2 = midiMsg.data2;
midiEvent.Data3 = midiMsg.data3;
MIDI_Device_SendEventPacket(&Keyboard_MIDI_Interface, &midiEvent);
MIDI_Device_Flush(&Keyboard_MIDI_Interface);
/* Turn on the TX led and starts its timer */
LEDs_TurnOnLEDs(LEDS_LED1);
led1_ticks = LED_ON_TICKS;
}
/* Turn off the Tx LED when the tick count reaches zero */
if (led1_ticks) {
led1_ticks--;
if (led1_ticks == 0) {
LEDs_TurnOffLEDs(LEDS_LED1);
}
}
if (MIDI_Device_ReceiveEventPacket(&Keyboard_MIDI_Interface, &midiEvent)) {
RingBuff_Count_t count = RingBuffer_GetCount(&USBtoUSART_Buffer);
/* Room to send a message? */
if ((BUFFER_SIZE - count) >= sizeof(midiMsg)) {
midiMsg.command = midiEvent.Command << 4;
midiMsg.channel = (midiEvent.Data1 & 0x0F) + 1;
midiMsg.data2 = midiEvent.Data2;
midiMsg.data3 = midiEvent.Data3;
for (ind=0; ind<sizeof(midiMsg); ind++) {
RingBuffer_Insert(&USBtoUSART_Buffer, ((uint8_t *)&midiMsg)[ind]);
}
/* Turn on the RX led and start its timer */
LEDs_TurnOnLEDs(LEDS_LED2);
led2_ticks = LED_ON_TICKS;
} else {
/* Turn on the RX led and leave it on to indicate the
* buffer is full and the sketch is not reading it
* fast enough.
*/
LEDs_TurnOnLEDs(LEDS_LED2);
}
/* if there's no room in the serial buffer the message gets dropped */
}
/* Turn off the RX LED when the tick count reaches zero */
if (led2_ticks) {
led2_ticks--;
if (led2_ticks == 0) {
LEDs_TurnOffLEDs(LEDS_LED2);
}
}
/* any data to send to main processor? */
if (!(RingBuffer_IsEmpty(&USBtoUSART_Buffer))) {
Serial_TxByte(RingBuffer_Remove(&USBtoUSART_Buffer));
}
MIDI_Device_USBTask(&Keyboard_MIDI_Interface);
USB_USBTask();
}
}
/** Event handler for the USB_DeviceEnumerationComplete event. This indicates that a device has been successfully
* enumerated by the host and is now ready to be used by the application.
*/
void EVENT_USB_Host_DeviceEnumerationComplete(void)
{
puts_P(PSTR("Getting Config Data.\r\n"));
uint8_t ErrorCode;
/* Get and process the configuration descriptor data */
if ((ErrorCode = ProcessConfigurationDescriptor()) != SuccessfulConfigRead)
{
if (ErrorCode == ControlError)
puts_P(PSTR(ESC_FG_RED "Control Error (Get Configuration).\r\n"));
else
puts_P(PSTR(ESC_FG_RED "Invalid Device.\r\n"));
printf_P(PSTR(" -- Error Code: %d\r\n"), ErrorCode);
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
return;
}
/* Set the device configuration to the first configuration (rarely do devices use multiple configurations) */
if ((ErrorCode = USB_Host_SetDeviceConfiguration(1)) != HOST_SENDCONTROL_Successful)
{
printf_P(PSTR(ESC_FG_RED "Control Error (Set Configuration).\r\n"
" -- Error Code: %d\r\n" ESC_FG_WHITE), ErrorCode);
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
return;
}
/* Some printers use alternate settings to determine the communication protocol used - if so, send a SetInterface
* request to switch to the interface alternate setting with the Bidirectional protocol */
if (PrinterAltSetting)
{
if ((ErrorCode = USB_Host_SetInterfaceAltSetting(PrinterInterfaceNumber, PrinterAltSetting)) != HOST_SENDCONTROL_Successful)
{
printf_P(PSTR(ESC_FG_RED "Control Error (Set Interface).\r\n"
" -- Error Code: %d\r\n" ESC_FG_WHITE), ErrorCode);
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
USB_Host_SetDeviceConfiguration(0);
return;
}
}
puts_P(PSTR("Retrieving Device ID...\r\n"));
char DeviceIDString[300];
if ((ErrorCode = Printer_GetDeviceID(DeviceIDString, sizeof(DeviceIDString))) != HOST_SENDCONTROL_Successful)
{
printf_P(PSTR(ESC_FG_RED "Control Error (Get Device ID).\r\n"
" -- Error Code: %d\r\n" ESC_FG_WHITE), ErrorCode);
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
USB_Host_SetDeviceConfiguration(0);
return;
}
printf_P(PSTR("Printer Device ID: %s\r\n"), DeviceIDString);
puts_P(PSTR("Printer Enumerated.\r\n"));
LEDs_SetAllLEDs(LEDMASK_USB_READY);
}
/** Writes a report to the attached device.
*
* \param[in] ReportOUTData Buffer containing the report to send to the device
* \param[in] ReportIndex Index of the report in the device (zero if the device does not use multiple reports)
* \param[in] ReportType Type of report to send, either REPORT_TYPE_OUT or REPORT_TYPE_FEATURE
* \param[in] ReportLength Length of the report to send
*/
void WriteNextReport(uint8_t* ReportOUTData,
const uint8_t ReportIndex,
const uint8_t ReportType,
uint16_t ReportLength)
{
/* Select the HID data OUT pipe */
Pipe_SelectPipe(HID_DATA_OUT_PIPE);
/* Not all HID devices have an OUT endpoint (some require OUT reports to be sent over the
* control endpoint instead) - check to see if the OUT endpoint has been initialized */
if (Pipe_IsConfigured() && (ReportType == REPORT_TYPE_OUT))
{
Pipe_Unfreeze();
/* Ensure pipe is ready to be written to before continuing */
if (!(Pipe_IsOUTReady()))
{
/* Refreeze the data OUT pipe */
Pipe_Freeze();
return;
}
/* If the report index is used, send it before the report data */
if (ReportIndex)
Pipe_Write_Byte(ReportIndex);
/* Write out HID report data */
Pipe_Write_Stream_LE(ReportOUTData, ReportLength);
/* Clear the OUT endpoint, send last data packet */
Pipe_ClearOUT();
/* Refreeze the data OUT pipe */
Pipe_Freeze();
}
else
{
/* Class specific request to send a HID report to the device */
USB_ControlRequest = (USB_Request_Header_t)
{
.bmRequestType = (REQDIR_HOSTTODEVICE | REQTYPE_CLASS | REQREC_INTERFACE),
.bRequest = REQ_SetReport,
.wValue = ((ReportType << 8) | ReportIndex),
.wIndex = 0,
.wLength = ReportLength,
};
/* Select the control pipe for the request transfer */
Pipe_SelectPipe(PIPE_CONTROLPIPE);
/* Send the request to the device */
USB_Host_SendControlRequest(ReportOUTData);
}
}
/** Task to set the configuration of the attached device after it has been enumerated, and to read and process
* HID reports from the device and to send reports if desired.
*/
void HID_Host_Task(void)
{
uint8_t ErrorCode;
/* Switch to determine what user-application handled host state the host state machine is in */
switch (USB_HostState)
{
case HOST_STATE_Addressed:
puts_P(PSTR("Getting Config Data.\r\n"));
/* Get and process the configuration descriptor data */
if ((ErrorCode = ProcessConfigurationDescriptor()) != SuccessfulConfigRead)
{
if (ErrorCode == ControlError)
puts_P(PSTR(ESC_FG_RED "Control Error (Get Configuration).\r\n"));
else
puts_P(PSTR(ESC_FG_RED "Invalid Device.\r\n"));
printf_P(PSTR(" -- Error Code: %d\r\n" ESC_FG_WHITE), ErrorCode);
/* Indicate error status */
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
/* Wait until USB device disconnected */
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
break;
}
/* Set the device configuration to the first configuration (rarely do devices use multiple configurations) */
if ((ErrorCode = USB_Host_SetDeviceConfiguration(1)) != HOST_SENDCONTROL_Successful)
{
printf_P(PSTR(ESC_FG_RED "Control Error (Set Configuration).\r\n"
" -- Error Code: %d\r\n" ESC_FG_WHITE), ErrorCode);
/* Indicate error status */
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
/* Wait until USB device disconnected */
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
break;
}
puts_P(PSTR("HID Device Enumerated.\r\n"));
USB_HostState = HOST_STATE_Configured;
break;
case HOST_STATE_Configured:
ReadNextReport();
break;
}
}
/** Task to set the configuration of the attached device after it has been enumerated, and to print device information
* through the serial port.
*/
void StillImage_Task(void)
{
uint8_t ErrorCode;
switch (USB_HostState)
{
case HOST_STATE_Addressed:
puts_P(PSTR("Getting Config Data.\r\n"));
/* Get and process the configuration descriptor data */
if ((ErrorCode = ProcessConfigurationDescriptor()) != SuccessfulConfigRead)
{
if (ErrorCode == ControlError)
puts_P(PSTR(ESC_FG_RED "Control Error (Get Configuration).\r\n"));
else
puts_P(PSTR(ESC_FG_RED "Invalid Device.\r\n"));
printf_P(PSTR(" -- Error Code: %d\r\n" ESC_FG_WHITE), ErrorCode);
/* Indicate error via status LEDs */
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
/* Wait until USB device disconnected */
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
break;
}
/* Set the device configuration to the first configuration (rarely do devices use multiple configurations) */
if ((ErrorCode = USB_Host_SetDeviceConfiguration(1)) != HOST_SENDCONTROL_Successful)
{
printf_P(PSTR(ESC_FG_RED "Control Error (Set Configuration).\r\n"
" -- Error Code: %d\r\n" ESC_FG_WHITE), ErrorCode);
/* Indicate error via status LEDs */
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
/* Wait until USB device disconnected */
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
break;
}
puts_P(PSTR("Still Image Device Enumerated.\r\n"));
USB_HostState = HOST_STATE_Configured;
break;
case HOST_STATE_Configured:
/* Indicate device busy via the status LEDs */
LEDs_SetAllLEDs(LEDMASK_USB_BUSY);
puts_P(PSTR("Retrieving Device Info...\r\n"));
PIMA_SendBlock = (PIMA_Container_t)
{
.DataLength = PIMA_COMMAND_SIZE(0),
.Type = CType_CommandBlock,
.Code = PIMA_OPERATION_GETDEVICEINFO,
.TransactionID = 0x00000000,
.Params = {},
};
/* Send the GETDEVICEINFO block */
SImage_SendBlockHeader();
/* Receive the response data block */
if ((ErrorCode = SImage_ReceiveBlockHeader()) != PIPE_RWSTREAM_NoError)
{
ShowCommandError(ErrorCode, false);
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
break;
}
/* Calculate the size of the returned device info data structure */
uint16_t DeviceInfoSize = (PIMA_ReceivedBlock.DataLength - PIMA_COMMAND_SIZE(0));
/* Create a buffer large enough to hold the entire device info */
uint8_t DeviceInfo[DeviceInfoSize];
/* Read in the data block data (containing device info) */
SImage_ReadData(DeviceInfo, DeviceInfoSize);
/* Once all the data has been read, the pipe must be cleared before the response can be sent */
Pipe_ClearIN();
/* Create a pointer for walking through the info dataset */
uint8_t* DeviceInfoPos = DeviceInfo;
/* Skip over the data before the unicode device information strings */
DeviceInfoPos += 8; // Skip to VendorExtensionDesc String
DeviceInfoPos += (1 + UNICODE_STRING_LENGTH(*DeviceInfoPos)); // Skip over VendorExtensionDesc String
DeviceInfoPos += 2; // Skip over FunctionalMode
DeviceInfoPos += (4 + (*(uint32_t*)DeviceInfoPos << 1)); // Skip over Supported Operations Array
DeviceInfoPos += (4 + (*(uint32_t*)DeviceInfoPos << 1)); // Skip over Supported Events Array
DeviceInfoPos += (4 + (*(uint32_t*)DeviceInfoPos << 1)); // Skip over Supported Device Properties Array
DeviceInfoPos += (4 + (*(uint32_t*)DeviceInfoPos << 1)); // Skip over Capture Formats Array
DeviceInfoPos += (4 + (*(uint32_t*)DeviceInfoPos << 1)); // Skip over Image Formats Array
/* Extract and convert the Manufacturer Unicode string to ASCII and print it through the USART */
char Manufacturer[*DeviceInfoPos];
UnicodeToASCII(DeviceInfoPos, Manufacturer);
printf_P(PSTR(" Manufacturer: %s\r\n"), Manufacturer);
DeviceInfoPos += 1 + UNICODE_STRING_LENGTH(*DeviceInfoPos); // Skip over Manufacturer String
/* Extract and convert the Model Unicode string to ASCII and print it through the USART */
char Model[*DeviceInfoPos];
UnicodeToASCII(DeviceInfoPos, Model);
printf_P(PSTR(" Model: %s\r\n"), Model);
DeviceInfoPos += 1 + UNICODE_STRING_LENGTH(*DeviceInfoPos); // Skip over Model String
/* Extract and convert the Device Version Unicode string to ASCII and print it through the USART */
char DeviceVersion[*DeviceInfoPos];
UnicodeToASCII(DeviceInfoPos, DeviceVersion);
printf_P(PSTR(" Device Version: %s\r\n"), DeviceVersion);
/* Receive the final response block from the device */
if ((ErrorCode = SImage_ReceiveBlockHeader()) != PIPE_RWSTREAM_NoError)
{
ShowCommandError(ErrorCode, false);
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
break;
}
/* Verify that the command completed successfully */
if ((PIMA_ReceivedBlock.Type != CType_ResponseBlock) || (PIMA_ReceivedBlock.Code != PIMA_RESPONSE_OK))
{
ShowCommandError(PIMA_ReceivedBlock.Code, true);
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
break;
}
puts_P(PSTR("Opening Session...\r\n"));
PIMA_SendBlock = (PIMA_Container_t)
{
.DataLength = PIMA_COMMAND_SIZE(1),
.Type = CType_CommandBlock,
.Code = PIMA_OPERATION_OPENSESSION,
.TransactionID = 0x00000000,
.Params = {0x00000001},
};
/* Send the OPENSESSION block, open a session with an ID of 0x0001 */
SImage_SendBlockHeader();
/* Receive the response block from the device */
if ((ErrorCode = SImage_ReceiveBlockHeader()) != PIPE_RWSTREAM_NoError)
{
ShowCommandError(ErrorCode, false);
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
break;
}
/* Verify that the command completed successfully */
if ((PIMA_ReceivedBlock.Type != CType_ResponseBlock) || (PIMA_ReceivedBlock.Code != PIMA_RESPONSE_OK))
{
ShowCommandError(PIMA_ReceivedBlock.Code, true);
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
break;
}
puts_P(PSTR("Closing Session...\r\n"));
PIMA_SendBlock = (PIMA_Container_t)
{
.DataLength = PIMA_COMMAND_SIZE(1),
.Type = CType_CommandBlock,
.Code = PIMA_OPERATION_CLOSESESSION,
.TransactionID = 0x00000001,
.Params = {0x00000001},
};
/* Send the CLOSESESSION block, close the session with an ID of 0x0001 */
SImage_SendBlockHeader();
/* Receive the response block from the device */
if ((ErrorCode = SImage_ReceiveBlockHeader()) != PIPE_RWSTREAM_NoError)
{
ShowCommandError(ErrorCode, false);
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
break;
}
/* Verify that the command completed successfully */
if ((PIMA_ReceivedBlock.Type != CType_ResponseBlock) || (PIMA_ReceivedBlock.Code != PIMA_RESPONSE_OK))
{
ShowCommandError(PIMA_ReceivedBlock.Code, true);
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
break;
}
puts_P(PSTR("Done.\r\n"));
/* Indicate device no longer busy */
LEDs_SetAllLEDs(LEDMASK_USB_READY);
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
break;
}
}
/** Function to convert a given Unicode encoded string to ASCII. This function will only work correctly on Unicode
* strings which contain ASCII printable characters only.
*
* \param[in] UnicodeString Pointer to a Unicode encoded input string
* \param[out] Buffer Pointer to a buffer where the converted ASCII string should be stored
*/
void UnicodeToASCII(uint8_t* UnicodeString,
char* Buffer)
{
/* Get the number of characters in the string, skip to the start of the string data */
uint8_t CharactersRemaining = *(UnicodeString++);
/* Loop through the entire unicode string */
while (CharactersRemaining--)
{
/* Load in the next unicode character (only the lower byte, as only Unicode coded ASCII is supported) */
*(Buffer++) = *UnicodeString;
/* Jump to the next unicode character */
UnicodeString += 2;
}
/* Null terminate the string */
*Buffer = 0;
}
/** Displays a PIMA command error via the device's serial port.
*
* \param[in] ErrorCode Error code of the function which failed to complete successfully
* \param[in] ResponseCodeError Indicates if the error is due to a command failed indication from the device, or a communication failure
*/
void ShowCommandError(uint8_t ErrorCode,
bool ResponseCodeError)
{
char* FailureType = ((ResponseCodeError) ? PSTR("Response Code != OK") : PSTR("Transaction Fail"));
printf_P(PSTR(ESC_FG_RED "Command Error (%S).\r\n"
" -- Error Code %d\r\n" ESC_FG_WHITE), FailureType, ErrorCode);
/* Indicate error via status LEDs */
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
}
/** Event handler for the library USB Connection event. */
void EVENT_USB_Device_Connect(void)
{
PulseMSRemaining.PingPongLEDPulse = PING_PONG_LED_PULSE_MS;
LEDs_SetAllLEDs(LEDMASK_TX);
}
/** Event handler for the USB_DeviceAttached event. This indicates that a device has been attached to the host, and
* starts the library USB task to begin the enumeration and USB management process.
*/
void EVENT_USB_Host_DeviceAttached(void)
{
puts_P(PSTR(ESC_FG_GREEN "Device Attached.\r\n" ESC_FG_WHITE));
LEDs_SetAllLEDs(LEDMASK_USB_ENUMERATING);
}
/** Event handler for the library USB Disconnection event. */
void EVENT_USB_Device_Disconnect(void)
{
PulseMSRemaining.PingPongLEDPulse = 0;
LEDs_SetAllLEDs(LEDS_NO_LEDS);
}
/** Event handler for the USB_DeviceAttached event. This indicates that a device has been attached to the host, and
* starts the library USB task to begin the enumeration and USB management process.
*/
void EVENT_USB_Host_DeviceAttached(void)
{
puts_P(PSTR("Device Attached.\r\n"));
LEDs_SetAllLEDs(LEDMASK_USB_ENUMERATING);
}
void EVENT_USB_Host_DeviceAttached(void)
{
LEDs_SetAllLEDs(LEDMASK_USB_ENUMERATING);
}
/** Event handler for the USB_Connect event. This indicates that the device is enumerating via the status LEDs and
* starts the library USB task to begin the enumeration and USB management process.
*/
void EVENT_USB_Device_Connect(void)
{
/* Indicate USB enumerating */
LEDs_SetAllLEDs(LEDMASK_USB_ENUMERATING);
}
void EVENT_USB_Host_DeviceUnattached(void)
{
LEDs_SetAllLEDs(LEDMASK_USB_NOTREADY);
}
/** Checks for changes in the position of the board joystick, sending MIDI events to the host upon each change. */
void CheckJoystickMovement(void)
{
static uint8_t PrevJoystickStatus;
uint8_t MIDICommand = 0;
uint8_t MIDIPitch;
/* Get current joystick mask, XOR with previous to detect joystick changes */
uint8_t JoystickStatus = Joystick_GetStatus();
uint8_t JoystickChanges = (JoystickStatus ^ PrevJoystickStatus);
/* Get board button status - if pressed use channel 10 (percussion), otherwise use channel 1 */
uint8_t Channel = ((Buttons_GetStatus() & BUTTONS_BUTTON1) ? MIDI_CHANNEL(10) : MIDI_CHANNEL(1));
if (JoystickChanges & JOY_LEFT)
{
MIDICommand = ((JoystickStatus & JOY_LEFT)? MIDI_COMMAND_NOTE_ON : MIDI_COMMAND_NOTE_OFF);
MIDIPitch = 0x3C;
}
if (JoystickChanges & JOY_UP)
{
MIDICommand = ((JoystickStatus & JOY_UP)? MIDI_COMMAND_NOTE_ON : MIDI_COMMAND_NOTE_OFF);
MIDIPitch = 0x3D;
}
if (JoystickChanges & JOY_RIGHT)
{
MIDICommand = ((JoystickStatus & JOY_RIGHT)? MIDI_COMMAND_NOTE_ON : MIDI_COMMAND_NOTE_OFF);
MIDIPitch = 0x3E;
}
if (JoystickChanges & JOY_DOWN)
{
MIDICommand = ((JoystickStatus & JOY_DOWN)? MIDI_COMMAND_NOTE_ON : MIDI_COMMAND_NOTE_OFF);
MIDIPitch = 0x3F;
}
if (JoystickChanges & JOY_PRESS)
{
MIDICommand = ((JoystickStatus & JOY_PRESS)? MIDI_COMMAND_NOTE_ON : MIDI_COMMAND_NOTE_OFF);
MIDIPitch = 0x3B;
}
if (MIDICommand)
{
MIDI_EventPacket_t MIDIEvent = (MIDI_EventPacket_t)
{
.Event = MIDI_EVENT(0, MIDICommand),
.Data1 = MIDICommand | Channel,
.Data2 = MIDIPitch,
.Data3 = MIDI_STANDARD_VELOCITY,
};
MIDI_Device_SendEventPacket(&Keyboard_MIDI_Interface, &MIDIEvent);
MIDI_Device_Flush(&Keyboard_MIDI_Interface);
}
PrevJoystickStatus = JoystickStatus;
}
/** Event handler for the library USB Connection event. */
void EVENT_USB_Device_Connect(void)
{
LEDs_SetAllLEDs(LEDMASK_USB_ENUMERATING);
}
void DiskHost_USBTask(void)
{
if (USB_HostState == HOST_STATE_Addressed)
{
LEDs_SetAllLEDs(LEDMASK_USB_ENUMERATING);
uint16_t ConfigDescriptorSize;
uint8_t ConfigDescriptorData[512];
if (USB_Host_GetDeviceConfigDescriptor(1, &ConfigDescriptorSize, ConfigDescriptorData,
sizeof(ConfigDescriptorData)) != HOST_GETCONFIG_Successful)
{
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
return;
}
if (MS_Host_ConfigurePipes(&DiskHost_MS_Interface,
ConfigDescriptorSize, ConfigDescriptorData) != MS_ENUMERROR_NoError)
{
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
return;
}
if (USB_Host_SetDeviceConfiguration(1) != HOST_SENDCONTROL_Successful)
{
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
return;
}
uint8_t MaxLUNIndex;
if (MS_Host_GetMaxLUN(&DiskHost_MS_Interface, &MaxLUNIndex))
{
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
return;
}
if (MS_Host_ResetMSInterface(&DiskHost_MS_Interface))
{
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
return;
}
USB_HostState = HOST_STATE_Configured;
/* Note: For the RequestSense call to work, the host state machine must be in the
* Configured state, or the call will be aborted */
SCSI_Request_Sense_Response_t SenseData;
if (MS_Host_RequestSense(&DiskHost_MS_Interface, 0, &SenseData) != 0)
{
LEDs_SetAllLEDs(LEDMASK_USB_ERROR);
USB_HostState = HOST_STATE_WaitForDeviceRemoval;
return;
}
pf_mount(&DiskFATState);
LEDs_SetAllLEDs(LEDMASK_USB_READY);
}
MS_Host_USBTask(&DiskHost_MS_Interface);
}
/** Event handler for the USB_Disconnect event. This indicates that the device is no longer connected to a host via
* the status LEDs and stops the USB management and CDC management tasks.
*/
void EVENT_USB_Device_Disconnect(void)
{
LEDs_SetAllLEDs(LEDMASK_USB_NOTREADY);
}
/** Event handler for the library USB Connection event. */
void EVENT_USB_Device_Connect(void)
{
LEDs_SetAllLEDs(LEDMASK_USB_ENUMERATING);
uIPManagement_Init();
}
