C++ (Cpp) LEDx_GPIO_CLK_ENABLE примеры использования

Пример #1

Файл: stm32l4xx_nucleo.c Проект: LedgerHQ/blue-nonsecure-firmware

/**
  * @brief  Configures LED GPIO.
  * @param  Led: LED to be configured. 
  *          This parameter can be one of the following values:
  *            @arg  LED2
  * @retval None
  */
void BSP_LED_Init(Led_TypeDef Led)
{
  GPIO_InitTypeDef  gpioinitstruct = {0};
  
  /* Enable the GPIO_LED Clock */
  LEDx_GPIO_CLK_ENABLE(Led);

  /* Configure the GPIO_LED pin */
  gpioinitstruct.Pin   = GPIO_PIN[Led];
  gpioinitstruct.Mode  = GPIO_MODE_OUTPUT_PP;
  gpioinitstruct.Pull  = GPIO_NOPULL;
  gpioinitstruct.Speed = GPIO_SPEED_FREQ_HIGH;
  HAL_GPIO_Init(GPIO_PORT[Led], &gpioinitstruct);
}

Пример #2

Файл: stm324xg_eval.c Проект: BradleyConn/stm32f429

/**
  * @brief  Configures LED GPIO.
  * @param  Led: LED to be configured. 
  *          This parameter can be one of the following values:
  *            @arg  LED1
  *            @arg  LED2
  *            @arg  LED3
  *            @arg  LED4
  * @retval None
  */
void BSP_LED_Init(Led_TypeDef Led)
{
  GPIO_InitTypeDef  GPIO_InitStruct;
  
  /* Enable the GPIO_LED clock */
  LEDx_GPIO_CLK_ENABLE(Led);

  /* Configure the GPIO_LED pin */
  GPIO_InitStruct.Pin = GPIO_PIN[Led];
  GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
  GPIO_InitStruct.Pull = GPIO_PULLUP;
  GPIO_InitStruct.Speed = GPIO_SPEED_FAST;
  
  HAL_GPIO_Init(GPIO_PORT[Led], &GPIO_InitStruct);
}

Пример #3

Файл: stm32l0xx_nucleo_32.c Проект: S4mw1s3/Nucleo32

/**
  * @brief  Configures LED GPIO.
  * @param  Led: Specifies the Led to be configured. 
  *   This parameter can be one of following parameters:
  *            @arg  LED3
  * @retval None
  */
void BSP_LED_Init(Led_TypeDef Led)
{
  GPIO_InitTypeDef  GPIO_InitStruct;
  
  /* Enable the GPIO_LED Clock */
  LEDx_GPIO_CLK_ENABLE(Led);

  /* Configure the GPIO_LED pin */
  GPIO_InitStruct.Pin = LED_PIN[Led];
  GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
  GPIO_InitStruct.Pull = GPIO_NOPULL;
  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
  
  HAL_GPIO_Init(LED_PORT[Led], &GPIO_InitStruct);
  HAL_GPIO_WritePin(LED_PORT[Led], LED_PIN[Led], GPIO_PIN_RESET); 
}

Пример #4

Файл: stm32f1xx_nucleo.c Проект: cnoviello/stm32-nucleof1

/**
  * @brief  Configures LED GPIO.
  * @param  Led: LED to be configured. 
  *          This parameter can be one of the following values:
  *     @arg LED2
  * @retval None
  */
void BSP_LED_Init(Led_TypeDef Led)
{
  GPIO_InitTypeDef  gpioinitstruct = {0};
  
  /* Enable the GPIO_LED Clock */
  LEDx_GPIO_CLK_ENABLE(Led);

  /* Configure the GPIO_LED pin */
  gpioinitstruct.Pin    = GPIO_PIN[Led];
  gpioinitstruct.Mode   = GPIO_MODE_OUTPUT_PP;
  gpioinitstruct.Pull   = GPIO_PULLUP;
  gpioinitstruct.Speed  = GPIO_SPEED_HIGH;
  HAL_GPIO_Init(GPIO_PORT[Led], &gpioinitstruct);

  /* Reset PIN to switch off the LED */
  HAL_GPIO_WritePin(GPIO_PORT[Led],GPIO_PIN[Led], GPIO_PIN_RESET);
}

Пример #5

Файл: stm32303e_eval.c Проект: afconsult-south/dragonfly-fcb

/**
  * @brief  Configures LED GPIO.
  * @param  Led: Specifies the Led to be configured. 
  *   This parameter can be one of following parameters:
  *     @arg LED1
  *     @arg LED2
  *     @arg LED3
  *     @arg LED4
  * @retval None
  */
void BSP_LED_Init(Led_TypeDef Led)
{
  GPIO_InitTypeDef  GPIO_InitStructure;
  
  /* Enable the GPIO_LED clock */
  LEDx_GPIO_CLK_ENABLE(Led);

  /* Configure the GPIO_LED pin */
  GPIO_InitStructure.Pin = LED_PIN[Led];
  GPIO_InitStructure.Mode = GPIO_MODE_OUTPUT_PP;
  GPIO_InitStructure.Pull = GPIO_PULLUP;
  GPIO_InitStructure.Speed = GPIO_SPEED_HIGH;
  
  HAL_GPIO_Init(LED_PORT[Led], &GPIO_InitStructure);
  
  HAL_GPIO_WritePin(LED_PORT[Led], LED_PIN[Led], GPIO_PIN_SET); 
}