Пример #1
0
status_t LSM303C::begin(InterfaceMode_t im, MAG_DO_t modr, MAG_FS_t mfs,
    MAG_BDU_t mbu, MAG_OMXY_t mxyodr, MAG_OMZ_t mzodr, MAG_MD_t mm,
    ACC_FS_t afs, ACC_BDU_t abu, uint8_t aea, ACC_ODR_t aodr)
{
  uint8_t successes = 0;
  // Select I2C or SPI
  interfaceMode = im;
  enableIMU();
  
  ////////// Initialize Magnetometer //////////
  // Initialize magnetometer output data rate
  successes += MAG_SetODR(modr);
  // Initialize magnetic field full scale
  successes += MAG_SetFullScale(mfs);
  // Enabling block data updating
  successes += MAG_BlockDataUpdate(mbu);
  // Initialize magnetometer X/Y axes ouput data rate
  successes += MAG_XY_AxOperativeMode(mxyodr);
  // Initialize magnetometer Z axis performance mode
  successes += MAG_Z_AxOperativeMode(mzodr);
  // Initialize magnetometer run mode.
  successes += MAG_SetMode(mm);

  ////////// Initialize Accelerometer //////////
  // Initialize acceleration full scale
  successes += ACC_SetFullScale(afs);
  // Enable block data updating
  successes += ACC_BlockDataUpdate(abu);
  // Enable X, Y, and Z accelerometer axes
  successes += ACC_EnableAxis(aea);
  // Initialize accelerometer output data rate
  successes += ACC_SetODR(aodr);

  return (successes == IMU_SUCCESS) ? IMU_SUCCESS : IMU_HW_ERROR;
}
status_t LSM303C::begin(InterfaceMode_t im, MAG_DO_t modr, MAG_FS_t mfs,
    MAG_BDU_t mbu, MAG_OMXY_t mxyodr, MAG_OMZ_t mzodr, MAG_MD_t mm,
    ACC_FS_t afs, ACC_BDU_t abu, uint8_t aea, ACC_ODR_t aodr)
{
  uint8_t successes = 0;
  // Select I2C or SPI
  interfaceMode = im;

  if (interfaceMode == MODE_SPI)
  {
    debug_println("Setting up SPI");
    // Setup pins for SPI
    // CS & CLK must be outputs DDRxn = 1
    bitSet(DIR_REG, CSBIT_MAG);
    bitSet(DIR_REG, CSBIT_XL);
    bitSet(DIR_REG, CLKBIT);
    // Deselect SPI chips
    bitSet(CSPORT_MAG, CSBIT_MAG);
    bitSet(CSPORT_XL, CSBIT_XL);
    // Clock polarity (CPOL) = 1
    bitSet(CLKPORT, CLKBIT);
    // SPI Serial Interface Mode (SIM) bits must be set
    SPI_WriteByte(ACC, ACC_CTRL4, 0b111);
    SPI_WriteByte(MAG, MAG_CTRL_REG3, _BV(2));
  }
  else
  {
    Wire.begin();
    Wire.setClock(400000L);
  }
  ////////// Initialize Magnetometer //////////
  // Initialize magnetometer output data rate
  successes += MAG_SetODR(modr);
  // Initialize magnetic field full scale
  successes += MAG_SetFullScale(mfs);
  // Enabling block data updating
  successes += MAG_BlockDataUpdate(mbu);
  // Initialize magnetometer X/Y axes ouput data rate
  successes += MAG_XY_AxOperativeMode(mxyodr);
  // Initialize magnetometer Z axis performance mode
  successes += MAG_Z_AxOperativeMode(mzodr);
  // Initialize magnetometer run mode.
  successes += MAG_SetMode(mm);

  ////////// Initialize Accelerometer //////////
  // Initialize acceleration full scale
  successes += ACC_SetFullScale(afs);
  // Enable block data updating
  successes += ACC_BlockDataUpdate(abu);
  // Enable X, Y, and Z accelerometer axes
  successes += ACC_EnableAxis(aea);
  // Initialize accelerometer output data rate
  successes += ACC_SetODR(aodr);

  return (successes == IMU_SUCCESS) ? IMU_SUCCESS : IMU_HW_ERROR;
}