/*
* @brief Gets the robot ID.
*
* roneID is assigned robot ID. If robot is uninitialized, roneID is DEFAULT_RONEID.
* The ID is set using LM Flash. The format for the ID is: 00-50-C2-00-01-XX
* where XX is the robotID
* @returns void
*/
void systemIDInit(void) {
uint32 ureg0;
uint32 ureg1;
uint32 id = 0;
int i;
MAP_FlashUserGet(&ureg0, &ureg1);
for (i = 0; i < 2; i++) {
id = id << 8;
ureg1 = ureg1 >> 8;
id |= (ureg1 & 0xFF);
}
if (id == 0xFFFF) {
// Uninitialized robot. return DEFAULT_RONEID
roneID = DEFAULT_RONEID;
} else {
roneID = id & 0xFF;
}
}
/**
* Creates task to feed data from interrupt to lwIP,
* initializes EMAC0, then initializes lwIP
*/
void init_ethernet(void){/*{{{*/
{ // Enable Ethernet hardware/*{{{*/
uint32_t user0, user1;
/**
* Enable ethernet
* See page 160 of spmu298a
*/
MAP_SysCtlPeripheralEnable(SYSCTL_PERIPH_EMAC0);
MAP_SysCtlPeripheralReset(SYSCTL_PERIPH_EMAC0);
//Enable internal PHY
MAP_SysCtlPeripheralEnable(SYSCTL_PERIPH_EPHY0);
MAP_SysCtlPeripheralReset(SYSCTL_PERIPH_EPHY0);
// Set Ethernet LED pinouts
// See Page 269 of spmu298a.pdf
MAP_GPIOPinConfigure(GPIO_PF0_EN0LED0);
MAP_GPIOPinConfigure(GPIO_PF4_EN0LED1);
GPIOPinTypeEthernetLED(GPIO_PORTF_BASE, GPIO_PIN_0|GPIO_PIN_4);
// Busy wait until MAC ready
while(MAP_SysCtlPeripheralReady(SYSCTL_PERIPH_EMAC0) == 0);
//Using builtin PHY, so don't need to call GPIOPinTypeEthernetMII()
MAP_EMACPHYConfigSet(EMAC0_BASE, EMAC_PHY_TYPE_INTERNAL|EMAC_PHY_INT_MDIX_EN|EMAC_PHY_AN_100B_T_FULL_DUPLEX);
// Initialize MAC (see spmu363a.pdf)
// Maybe should optimize burst size
MAP_EMACInit(EMAC0_BASE, g_syshz, EMAC_BCONFIG_MIXED_BURST|EMAC_BCONFIG_PRIORITY_FIXED, 4, 4, 0);
// Set options
// Tune parameters
MAP_EMACConfigSet(EMAC0_BASE, (EMAC_CONFIG_FULL_DUPLEX |
EMAC_CONFIG_CHECKSUM_OFFLOAD |
EMAC_CONFIG_7BYTE_PREAMBLE |
EMAC_CONFIG_IF_GAP_96BITS |
EMAC_CONFIG_USE_MACADDR0 |
EMAC_CONFIG_SA_FROM_DESCRIPTOR |
EMAC_CONFIG_100MBPS|
EMAC_CONFIG_BO_LIMIT_1024),
(EMAC_MODE_RX_STORE_FORWARD |
EMAC_MODE_TX_STORE_FORWARD |
EMAC_MODE_TX_THRESHOLD_64_BYTES |
EMAC_MODE_RX_THRESHOLD_64_BYTES), 0);
//Mac Address saved in user0 and user1 by default
MAP_FlashUserGet(&user0, &user1);
mac_addr[0] = user0 & 0xFF;
mac_addr[1] = user0 >> 8 & 0xFF;
mac_addr[2] = user0 >> 16 & 0xFF;
mac_addr[3] = user1 & 0xFF;
mac_addr[4] = user1 >> 8 & 0xFF;
mac_addr[5] = user1 >> 16 & 0xFF;
MAP_EMACAddrSet(EMAC0_BASE, 0, mac_addr );
//Explicitly Disable PTP
EMACTimestampDisable(EMAC0_BASE);
}/*}}}*/
// Lower priority of ISR so *FromISR functions can be safely called
MAP_IntPrioritySet(INT_EMAC0, ETH_ISR_PRIO);
tcpip_init(tcpip_init_cb, NULL);
}/*}}}*/
