int main(void) {
MAP_SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_XTAL_16MHZ | SYSCTL_OSC_MAIN);
sysClock = SysCtlClockGet();
MAP_SysCtlPeripheralEnable(SYSCTL_PERIPH_I2C3);
MAP_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
MAP_GPIOPinConfigure(GPIO_PD1_I2C3SDA);
MAP_GPIOPinTypeI2C(GPIO_PORTD_BASE, GPIO_PIN_1);
MAP_GPIOPinConfigure(GPIO_PD0_I2C3SCL);
MAP_GPIOPinTypeI2CSCL(GPIO_PORTD_BASE, GPIO_PIN_0);
MAP_I2CMasterInitExpClk(I2C3_BASE, sysClock, 0);
pRTC->address = RTC_addr;
SysCtlDelay(20000);
setupRTC(pRTC);
SysCtlDelay(20000);
setTime(pRTC);
SysCtlDelay(20000);
getTime(pRTC);
return 0;
}
static inline void ti_arm_mcu_pin_mode_i2c(int pin, int scl, int i2c_af)
{
ti_arm_mcu_periph_enable(ti_arm_mcu_gpio_periph(pin));
if (i2c_af)
MAP_GPIOPinConfigure(i2c_af);
MAP_GPIOPinTypeI2C(ti_arm_mcu_gpio_base(pin), GPIO_BIT(pin));
if (scl)
ti_arm_mcu_pin_config(pin, GPIO_PIN_TYPE_STD_WPU);
else
ti_arm_mcu_pin_config(pin, GPIO_PIN_TYPE_OD);
}
/*
* ======== EK_TM4C123GXL_initI2C ========
*/
void EK_TM4C123GXL_initI2C(void)
{
//Enable the peripheral funcitonality for the GPIO port
//
MAP_SysCtlPeripheralEnable(INEEDMD_LED_SYSCTL_PRIPH_GPIO);
// Enable the I2C peripheral
//
MAP_SysCtlPeripheralEnable(INEEDMD_LED_SYSCTL_PRIPH_I2C);
// Configure the alternate function for the I2C SCL pin and tie it to the I2C
MAP_GPIOPinTypeI2CSCL(INEEDMD_LED_GPIO_PORT, INEEDMD_LED_I2CSCL_PIN);
MAP_GPIOPinConfigure(INEEDMD_LED_GPIO_I2CSCL);
//Configure the alternate function for the I2C SDA pin and tie it to the I2C
MAP_GPIOPinTypeI2C(INEEDMD_LED_GPIO_PORT, INEEDMD_LED_I2CSDA_PIN);
MAP_GPIOPinConfigure(INEEDMD_LED_GPIO_I2CSDA);
I2C_init();
return;
}
int main(void)
{
MAP_SysCtlClockSet(SYSCTL_SYSDIV_4 | SYSCTL_USE_PLL | SYSCTL_OSC_MAIN |SYSCTL_XTAL_12MHZ); //50MHZ
//
// Enable peripherals to operate when CPU is in sleep.
//
MAP_SysCtlPeripheralClockGating(true);
//
// Configure SysTick to occur 1000 times per second, to use as a time
// reference. Enable SysTick to generate interrupts.
//
MAP_SysTickPeriodSet(MAP_SysCtlClockGet() / SYSTICKS_PER_SECOND);
MAP_SysTickIntEnable();
MAP_SysTickEnable();
//
// Get the current processor clock frequency.
//
ulClockMS = MAP_SysCtlClockGet() / (3 * 1000);
// init Serial Comm
initSerialComm(230400);
// init SSI0 in slave mode
initSPIComm();
#ifdef DEBUG
UARTprintf("Setting up PID\n");
#endif
initCarPID();
#ifdef DEBUG
UARTprintf("done\n");
#endif
#ifdef DEBUG
UARTprintf("Setting up PWM ... \n");
#endif
configurePWM();
configureGPIO();
#ifdef DEBUG
UARTprintf("done\n");
#endif
#ifdef DEBUG
UARTprintf("Setting up Servo ... \n");
#endif
servo_init();
servo_setPosition(90);
#ifdef DEBUG
UARTprintf("done\n");
#endif
#ifdef DEBUG
UARTprintf("Starting QEI...");
#endif
encoder_init();
#ifdef DEBUG
UARTprintf("done\n");
#endif
#ifdef USE_I2C
#ifdef DEBUG
UARTprintf("Setting up I2C\n");
#endif
//I2C
MAP_SysCtlPeripheralEnable(SYSCTL_PERIPH_I2C0);
MAP_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
MAP_GPIOPinTypeI2C(GPIO_PORTB_AHB_BASE,GPIO_PIN_2 | GPIO_PIN_3);
MAP_I2CMasterInitExpClk(I2C0_MASTER_BASE,SysCtlClockGet(),true); //false = 100khz , true = 400khz
I2CMasterTimeoutSet(I2C0_MASTER_BASE, 1000);
#ifdef DEBUG
UARTprintf("done\n");
#endif
#endif
#ifdef USE_I2C
#ifdef USE_INA226
#ifdef DEBUG
UARTprintf("Setting up INA226\n");
#endif
initINA226();
#ifdef DEBUG
UARTprintf("done\n");
#endif
#endif
#endif
while (1)
{
}
}
//*****************************************************************************
//
// Initialize the I2C, MPU9150 and Gesture systems.
//
//*****************************************************************************
void
MotionInit(void)
{
//
// Enable port S used for motion interrupt.
//
MAP_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOS);
//
// The I2C3 peripheral must be enabled before use.
//
MAP_SysCtlPeripheralEnable(SYSCTL_PERIPH_I2C3);
MAP_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOG);
//
// Configure the pin muxing for I2C3 functions on port G4 and G5.
//
MAP_GPIOPinConfigure(GPIO_PG4_I2C3SCL);
MAP_GPIOPinConfigure(GPIO_PG5_I2C3SDA);
//
// Select the I2C function for these pins. This function will also
// configure the GPIO pins pins for I2C operation, setting them to
// open-drain operation with weak pull-ups. Consult the data sheet
// to see which functions are allocated per pin.
//
MAP_GPIOPinTypeI2CSCL(GPIO_PORTG_BASE, GPIO_PIN_4);
MAP_GPIOPinTypeI2C(GPIO_PORTG_BASE, GPIO_PIN_5);
//
// Configure and Enable the GPIO interrupt. Used for INT signal from the
// MPU9150
//
MAP_GPIOPinTypeGPIOInput(GPIO_PORTS_BASE, GPIO_PIN_2);
MAP_GPIOIntEnable(GPIO_PORTS_BASE, GPIO_PIN_2);
MAP_GPIOIntTypeSet(GPIO_PORTS_BASE, GPIO_PIN_2, GPIO_FALLING_EDGE);
MAP_IntEnable(INT_GPIOS);
//
// Enable interrupts to the processor.
//
MAP_IntMasterEnable();
//
// Initialize I2C3 peripheral.
//
I2CMInit(&g_sI2CInst, I2C3_BASE, INT_I2C3, 0xff, 0xff,
g_ui32SysClock);
//
// Set the motion state to initializing.
//
g_ui8MotionState = MOTION_STATE_INIT;
//
// Initialize the MPU9150 Driver.
//
MPU9150Init(&g_sMPU9150Inst, &g_sI2CInst, MPU9150_I2C_ADDRESS,
MotionCallback, &g_sMPU9150Inst);
//
// Wait for transaction to complete
//
MotionI2CWait(__FILE__, __LINE__);
//
// Write application specifice sensor configuration such as filter settings
// and sensor range settings.
//
g_sMPU9150Inst.pui8Data[0] = MPU9150_CONFIG_DLPF_CFG_94_98;
g_sMPU9150Inst.pui8Data[1] = MPU9150_GYRO_CONFIG_FS_SEL_250;
g_sMPU9150Inst.pui8Data[2] = (MPU9150_ACCEL_CONFIG_ACCEL_HPF_5HZ |
MPU9150_ACCEL_CONFIG_AFS_SEL_2G);
MPU9150Write(&g_sMPU9150Inst, MPU9150_O_CONFIG, g_sMPU9150Inst.pui8Data, 3,
MotionCallback, &g_sMPU9150Inst);
//
// Wait for transaction to complete
//
MotionI2CWait(__FILE__, __LINE__);
//
// Configure the data ready interrupt pin output of the MPU9150.
//
g_sMPU9150Inst.pui8Data[0] = (MPU9150_INT_PIN_CFG_INT_LEVEL |
MPU9150_INT_PIN_CFG_INT_RD_CLEAR |
MPU9150_INT_PIN_CFG_LATCH_INT_EN);
g_sMPU9150Inst.pui8Data[1] = MPU9150_INT_ENABLE_DATA_RDY_EN;
MPU9150Write(&g_sMPU9150Inst, MPU9150_O_INT_PIN_CFG,
g_sMPU9150Inst.pui8Data, 2, MotionCallback, &g_sMPU9150Inst);
//
// Wait for transaction to complete
//
MotionI2CWait(__FILE__, __LINE__);
//
// Initialize the DCM system.
//
CompDCMInit(&g_sCompDCMInst, 1.0f / ((float) MOTION_SAMPLE_FREQ_HZ),
DCM_ACCEL_WEIGHT, DCM_GYRO_WEIGHT, DCM_MAG_WEIGHT);
//
// Initialize the gesture instance and establish a initial state estimate.
//
GestureInit(&g_sGestureInst, g_pfInitProb, g_ppfPath, g_ppfTransitionProb,
g_ppfEmitProb, GESTURE_PATH_LENGTH, GESTURE_NUM_STATES,
GESTURE_STATE_IDLE);
}
//*****************************************************************************
//
// Main 'C' Language entry point.
//
//*****************************************************************************
int
main(void)
{
float fTemperature, fPressure, fAltitude;
int32_t i32IntegerPart;
int32_t i32FractionPart;
tContext sContext;
uint32_t ui32SysClock;
char pcBuf[15];
//
// Setup the system clock to run at 40 Mhz from PLL with crystal reference
//
ui32SysClock = MAP_SysCtlClockFreqSet((SYSCTL_XTAL_25MHZ |
SYSCTL_OSC_MAIN |
SYSCTL_USE_PLL |
SYSCTL_CFG_VCO_480), 40000000);
//
// Configure the device pins.
//
PinoutSet();
//
// Initialize the display driver.
//
Kentec320x240x16_SSD2119Init(ui32SysClock);
//
// Initialize the graphics context.
//
GrContextInit(&sContext, &g_sKentec320x240x16_SSD2119);
//
// Draw the application frame.
//
FrameDraw(&sContext, "bmp180");
//
// Flush any cached drawing operations.
//
GrFlush(&sContext);
//
// Enable UART0
//
MAP_SysCtlPeripheralEnable(SYSCTL_PERIPH_UART0);
//
// Initialize the UART for console I/O.
//
UARTStdioConfig(0, 115200, ui32SysClock);
//
// Print the welcome message to the terminal.
//
UARTprintf("\033[2JBMP180 Example\n");
//
// The I2C3 peripheral must be enabled before use.
//
MAP_SysCtlPeripheralEnable(SYSCTL_PERIPH_I2C3);
//
// Configure the pin muxing for I2C3 functions on port G4 and G5.
// This step is not necessary if your part does not support pin muxing.
//
MAP_GPIOPinConfigure(GPIO_PG4_I2C3SCL);
MAP_GPIOPinConfigure(GPIO_PG5_I2C3SDA);
//
// Select the I2C function for these pins. This function will also
// configure the GPIO pins pins for I2C operation, setting them to
// open-drain operation with weak pull-ups. Consult the data sheet
// to see which functions are allocated per pin.
//
MAP_GPIOPinTypeI2CSCL(GPIO_PORTG_BASE, GPIO_PIN_4);
MAP_GPIOPinTypeI2C(GPIO_PORTG_BASE, GPIO_PIN_5);
//
// Enable interrupts to the processor.
//
MAP_IntMasterEnable();
//
// Initialize I2C3 peripheral.
//
I2CMInit(&g_sI2CInst, I2C3_BASE, INT_I2C3, 0xff, 0xff,
ui32SysClock);
//
// Initialize the BMP180
//
BMP180Init(&g_sBMP180Inst, &g_sI2CInst, BMP180_I2C_ADDRESS,
BMP180AppCallback, &g_sBMP180Inst);
//
// Wait for initialization callback to indicate reset request is complete.
//
while(g_vui8DataFlag == 0)
{
//
// Wait for I2C Transactions to complete.
//
}
//
// Reset the data ready flag
//
g_vui8DataFlag = 0;
//
// Enable the system ticks at 10 hz.
//
MAP_SysTickPeriodSet(ui32SysClock / (10 * 3));
MAP_SysTickIntEnable();
MAP_SysTickEnable();
//
// Configure PQ4 to control the blue LED.
//
MAP_GPIOPinTypeGPIOOutput(GPIO_PORTQ_BASE, GPIO_PIN_4);
//
// Print temperature, pressure and altitude labels once on the LCD.
//
GrStringDraw(&sContext, "Temperature", 11,
((GrContextDpyWidthGet(&sContext) / 2) - 96),
((GrContextDpyHeightGet(&sContext) - 32) / 2) - 24, 1);
GrStringDraw(&sContext, "Pressure", 8,
((GrContextDpyWidthGet(&sContext) / 2) - 63),
(GrContextDpyHeightGet(&sContext) - 32) / 2, 1);
GrStringDraw(&sContext, "Altitude", 8,
((GrContextDpyWidthGet(&sContext) / 2) - 59),
((GrContextDpyHeightGet(&sContext) - 32) / 2) + 24, 1);
//
// Begin the data collection and printing. Loop Forever.
//
while(1)
{
//
// Read the data from the BMP180 over I2C. This command starts a
// temperature measurement. Then polls until temperature is ready.
// Then automatically starts a pressure measurement and polls for that
// to complete. When both measurement are complete and in the local
// buffer then the application callback is called from the I2C
// interrupt context. Polling is done on I2C interrupts allowing
// processor to continue doing other tasks as needed.
//
BMP180DataRead(&g_sBMP180Inst, BMP180AppCallback, &g_sBMP180Inst);
while(g_vui8DataFlag == 0)
{
//
// Wait for the new data set to be available.
//
}
//
// Reset the data ready flag.
//
g_vui8DataFlag = 0;
//
// Get a local copy of the latest temperature data in float format.
//
BMP180DataTemperatureGetFloat(&g_sBMP180Inst, &fTemperature);
//
// Convert the floats to an integer part and fraction part for easy
// print.
//
i32IntegerPart = (int32_t) fTemperature;
i32FractionPart =(int32_t) (fTemperature * 1000.0f);
i32FractionPart = i32FractionPart - (i32IntegerPart * 1000);
if(i32FractionPart < 0)
{
i32FractionPart *= -1;
}
//
// Print temperature with three digits of decimal precision to LCD and
// terminal.
//
usnprintf(pcBuf, sizeof(pcBuf), "%03d.%03d ", i32IntegerPart,
i32FractionPart);
GrStringDraw(&sContext, pcBuf, 8,
((GrContextDpyWidthGet(&sContext) / 2) + 16),
((GrContextDpyHeightGet(&sContext) - 32) / 2) - 24, 1);
UARTprintf("Temperature %3d.%03d\t\t", i32IntegerPart,
i32FractionPart);
//
// Get a local copy of the latest air pressure data in float format.
//
BMP180DataPressureGetFloat(&g_sBMP180Inst, &fPressure);
//
// Convert the floats to an integer part and fraction part for easy
// print.
//
i32IntegerPart = (int32_t) fPressure;
i32FractionPart =(int32_t) (fPressure * 1000.0f);
i32FractionPart = i32FractionPart - (i32IntegerPart * 1000);
if(i32FractionPart < 0)
{
i32FractionPart *= -1;
}
//
// Print Pressure with three digits of decimal precision to LCD and
// terminal.
//
usnprintf(pcBuf, sizeof(pcBuf), "%3d.%03d ", i32IntegerPart,
i32FractionPart);
GrStringDraw(&sContext, pcBuf, -1,
((GrContextDpyWidthGet(&sContext) / 2) + 16),
(GrContextDpyHeightGet(&sContext) - 32) / 2, 1);
UARTprintf("Pressure %3d.%03d\t\t", i32IntegerPart, i32FractionPart);
//
// Calculate the altitude.
//
fAltitude = 44330.0f * (1.0f - powf(fPressure / 101325.0f,
1.0f / 5.255f));
//
// Convert the floats to an integer part and fraction part for easy
// print.
//
i32IntegerPart = (int32_t) fAltitude;
i32FractionPart =(int32_t) (fAltitude * 1000.0f);
i32FractionPart = i32FractionPart - (i32IntegerPart * 1000);
if(i32FractionPart < 0)
{
i32FractionPart *= -1;
}
//
// Print altitude with three digits of decimal precision to LCD and
// terminal.
//
usnprintf(pcBuf, sizeof(pcBuf), "%3d.%03d ", i32IntegerPart,
i32FractionPart);
GrStringDraw(&sContext, pcBuf, 8,
((GrContextDpyWidthGet(&sContext) / 2) + 16),
((GrContextDpyHeightGet(&sContext) - 32) / 2) + 24, 1);
UARTprintf("Altitude %3d.%03d", i32IntegerPart, i32FractionPart);
//
// Print new line.
//
UARTprintf("\n");
//
// Delay to keep printing speed reasonable. About 100 milliseconds.
//
MAP_SysCtlDelay(ui32SysClock / (10 * 3));
}
}
//*****************************************************************************
//
//! Configures the device pins for the standard usages on the EK-TM4C1294XL.
//!
//! \param bEthernet is a boolean used to determine function of Ethernet pins.
//! If true Ethernet pins are configured as Ethernet LEDs. If false GPIO are
//! available for application use.
//! \param bUSB is a boolean used to determine function of USB pins. If true USB
//! pins are configured for USB use. If false then USB pins are available for
//! application use as GPIO.
//!
//! This function enables the GPIO modules and configures the device pins for
//! the default, standard usages on the EK-TM4C1294XL. Applications that
//! require alternate configurations of the device pins can either not call
//! this function and take full responsibility for configuring all the device
//! pins, or can reconfigure the required device pins after calling this
//! function.
//!
//! \return None.
//
//*****************************************************************************
void
PinoutSet(bool bEthernet, bool bUSB)
{
//
// Enable all the GPIO peripherals.
//
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOC);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOD);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOE);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOG);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOH);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOJ);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOK);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOL);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOM);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPION);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOP);
ROM_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOQ);
//
// PA0-1 are used for UART0.
//
ROM_GPIOPinConfigure(GPIO_PA0_U0RX);
ROM_GPIOPinConfigure(GPIO_PA1_U0TX);
ROM_GPIOPinTypeUART(GPIO_PORTA_BASE, GPIO_PIN_0 | GPIO_PIN_1);
//
// PB0-1/PD6/PL6-7 are used for USB.
// PQ4 can be used as a power fault detect on this board but it is not
// the hardware peripheral power fault input pin.
//
if(bUSB)
{
HWREG(GPIO_PORTD_BASE + GPIO_O_LOCK) = GPIO_LOCK_KEY;
HWREG(GPIO_PORTD_BASE + GPIO_O_CR) = 0xff;
ROM_GPIOPinConfigure(GPIO_PD6_USB0EPEN);
ROM_GPIOPinTypeUSBAnalog(GPIO_PORTB_BASE, GPIO_PIN_0 | GPIO_PIN_1);
ROM_GPIOPinTypeUSBDigital(GPIO_PORTD_BASE, GPIO_PIN_6);
ROM_GPIOPinTypeUSBAnalog(GPIO_PORTL_BASE, GPIO_PIN_6 | GPIO_PIN_7);
ROM_GPIOPinTypeGPIOInput(GPIO_PORTQ_BASE, GPIO_PIN_4);
}
else
{
//
// Keep the default config for most pins used by USB.
// Add a pull down to PD6 to turn off the TPS2052 switch
//
ROM_GPIOPinTypeGPIOInput(GPIO_PORTD_BASE, GPIO_PIN_6);
MAP_GPIOPadConfigSet(GPIO_PORTD_BASE, GPIO_PIN_6, GPIO_STRENGTH_2MA,
GPIO_PIN_TYPE_STD_WPD);
}
//
// PF0/PF4 are used for Ethernet LEDs.
//
if(bEthernet)
{
//
// this app wants to configure for ethernet LED function.
//
ROM_GPIOPinConfigure(GPIO_PF0_EN0LED0);
ROM_GPIOPinConfigure(GPIO_PF4_EN0LED1);
GPIOPinTypeEthernetLED(GPIO_PORTF_BASE, GPIO_PIN_0 | GPIO_PIN_4);
}
else
{
//
// This app does not want Ethernet LED function so configure as
// standard outputs for LED driving.
//
ROM_GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, GPIO_PIN_0 | GPIO_PIN_4);
//
// Default the LEDs to OFF.
//
ROM_GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_0 | GPIO_PIN_4, 0);
MAP_GPIOPadConfigSet(GPIO_PORTF_BASE, GPIO_PIN_0 | GPIO_PIN_4,
GPIO_STRENGTH_12MA, GPIO_PIN_TYPE_STD);
}
//
// PJ0 and J1 are used for user buttons
//
ROM_GPIOPinTypeGPIOInput(GPIO_PORTJ_BASE, GPIO_PIN_0 | GPIO_PIN_1);
ROM_GPIOPinWrite(GPIO_PORTJ_BASE, GPIO_PIN_0 | GPIO_PIN_1, 0);
//
// PN0 and PN1 are used for USER LEDs.
//
ROM_GPIOPinTypeGPIOOutput(GPIO_PORTN_BASE, GPIO_PIN_0 | GPIO_PIN_1);
MAP_GPIOPadConfigSet(GPIO_PORTN_BASE, GPIO_PIN_0 | GPIO_PIN_1,
GPIO_STRENGTH_12MA, GPIO_PIN_TYPE_STD);
//
// Default the LEDs to OFF.
//
ROM_GPIOPinWrite(GPIO_PORTN_BASE, GPIO_PIN_0 | GPIO_PIN_1, 0);
MAP_GPIOPinConfigure(GPIO_PB2_I2C0SCL);
MAP_GPIOPinConfigure(GPIO_PB3_I2C0SDA);
MAP_GPIOPinTypeI2C(GPIO_PORTB_BASE, GPIO_PIN_3);
MAP_GPIOPinTypeI2CSCL(GPIO_PORTB_BASE, GPIO_PIN_2);
MAP_GPIOPadConfigSet(GPIO_PORTB_BASE, GPIO_PIN_2 | GPIO_PIN_3, GPIO_STRENGTH_2MA,
GPIO_PIN_TYPE_OD);
MAP_GPIODirModeSet(GPIO_PORTB_BASE, GPIO_PIN_2 | GPIO_PIN_3, GPIO_DIR_MODE_HW);
}
