/* Setup for MCI Clock and Block Size */
static void mci_set_mode(struct mmc *mmc, u32 hz, u32 blklen)
{
atmel_mci_t *mci = (atmel_mci_t *)mmc->priv;
u32 bus_hz = get_mci_clk_rate();
u32 clkdiv = 255;
debug("mci: bus_hz is %u, setting clock %u Hz, block size %u\n",
bus_hz, hz, blklen);
if (hz > 0) {
/* find lowest clkdiv yielding a rate <= than requested */
for (clkdiv=0; clkdiv<255; clkdiv++) {
if ((bus_hz / (clkdiv+1) / 2) <= hz)
break;
}
}
printf("mci: setting clock %u Hz, block size %u\n",
(bus_hz / (clkdiv+1)) / 2, blklen);
blklen &= 0xfffc;
/* On some platforms RDPROOF and WRPROOF are ignored */
writel((MMCI_BF(CLKDIV, clkdiv)
| MMCI_BF(BLKLEN, blklen)
| MMCI_BIT(RDPROOF)
| MMCI_BIT(WRPROOF)), &mci->mr);
/*
* On some new platforms BLKLEN in mci->mr is ignored.
* Should use the BLKLEN in the block register.
*/
writel(MMCI_BF(BLKLEN, blklen), &mci->blkr);
initialized = 1;
}
/* Entered into mmc structure during driver init */
static void mci_set_ios(struct mmc *mmc)
{
atmel_mci_t *mci = (atmel_mci_t *)mmc->priv;
int busw = (mmc->bus_width == 4) ? 1 : 0;
/* Set the clock speed */
mci_set_mode(mmc, mmc->clock, MMC_DEFAULT_BLKLEN);
/*
* set the bus width and select slot for this interface
* there is no capability for multiple slots on the same interface yet
* Bitfield SCDBUS needs to be expanded to 2 bits for 8-bit buses
*/
writel(MMCI_BF(SCDBUS, busw) | MMCI_BF(SCDSEL, MCI_BUS), &mci->sdcr);
}
/* Return the CMDR with flags for a given command and data packet */
static u32 mci_encode_cmd(
struct mmc_cmd *cmd, struct mmc_data *data, u32* error_flags)
{
u32 cmdr = 0;
/* Default Flags for Errors */
*error_flags |= (MMCI_BIT(DTOE) | MMCI_BIT(RDIRE) | MMCI_BIT(RENDE) |
MMCI_BIT(RINDE) | MMCI_BIT(RTOE));
/* Default Flags for the Command */
cmdr |= MMCI_BIT(MAXLAT);
if (data) {
cmdr |= MMCI_BF(TRCMD, 1);
if (data->blocks > 1)
cmdr |= MMCI_BF(TRTYP, 1);
if (data->flags & MMC_DATA_READ)
cmdr |= MMCI_BIT(TRDIR);
}
if (cmd->resp_type & MMC_RSP_CRC)
*error_flags |= MMCI_BIT(RCRCE);
if (cmd->resp_type & MMC_RSP_136)
cmdr |= MMCI_BF(RSPTYP, 2);
else if (cmd->resp_type & MMC_RSP_BUSY)
cmdr |= MMCI_BF(RSPTYP, 3);
else if (cmd->resp_type & MMC_RSP_PRESENT)
cmdr |= MMCI_BF(RSPTYP, 1);
return cmdr | MMCI_BF(CMDNB, cmd->cmdidx);
}
static void mci_set_mode(unsigned long hz, unsigned long blklen)
{
unsigned long bus_hz;
unsigned long clkdiv;
bus_hz = get_mci_clk_rate();
clkdiv = (bus_hz / hz) / 2 - 1;
pr_debug("mmc: setting clock %lu Hz, block size %lu\n",
hz, blklen);
if (clkdiv & ~255UL) {
clkdiv = 255;
printf("mmc: clock %lu too low; setting CLKDIV to 255\n",
hz);
}
blklen &= 0xfffc;
mmci_writel(MR, (MMCI_BF(CLKDIV, clkdiv)
| MMCI_BF(BLKLEN, blklen)
| MMCI_BIT(RDPROOF)
| MMCI_BIT(WRPROOF)));
}
/* Entered into mmc structure during driver init */
static int mci_init(struct mmc *mmc)
{
atmel_mci_t *mci = (atmel_mci_t *)mmc->priv;
/* Initialize controller */
writel(MMCI_BIT(SWRST), &mci->cr); /* soft reset */
writel(MMCI_BIT(PWSDIS), &mci->cr); /* disable power save */
writel(MMCI_BIT(MCIEN), &mci->cr); /* enable mci */
writel(MMCI_BF(SCDSEL, MCI_BUS), &mci->sdcr); /* select port */
/* This delay can be optimized, but stick with max value */
writel(0x7f, &mci->dtor);
/* Disable Interrupts */
writel(~0UL, &mci->idr);
/* Set default clocks and blocklen */
mci_set_mode(mmc, CONFIG_SYS_MMC_CLK_OD, MMC_DEFAULT_BLKLEN);
return 0;
}
/*
* Entered into mmc structure during driver init
*
* Sends a command out on the bus and deals with the block data.
* Takes the mmc pointer, a command pointer, and an optional data pointer.
*/
static int
mci_send_cmd(struct mmc *mmc, struct mmc_cmd *cmd, struct mmc_data *data)
{
atmel_mci_t *mci = (atmel_mci_t *)mmc->priv;
u32 cmdr;
u32 error_flags = 0;
u32 status;
if (!initialized) {
puts ("MCI not initialized!\n");
return COMM_ERR;
}
/* Figure out the transfer arguments */
cmdr = mci_encode_cmd(cmd, data, &error_flags);
/* For multi blocks read/write, set the block register */
if ((cmd->cmdidx == MMC_CMD_READ_MULTIPLE_BLOCK)
|| (cmd->cmdidx == MMC_CMD_WRITE_MULTIPLE_BLOCK))
writel(data->blocks | MMCI_BF(BLKLEN, mmc->read_bl_len),
&mci->blkr);
/* Send the command */
writel(cmd->cmdarg, &mci->argr);
writel(cmdr, &mci->cmdr);
#ifdef DEBUG
dump_cmd(cmdr, cmd->cmdarg, 0, "DEBUG");
#endif
/* Wait for the command to complete */
while (!((status = readl(&mci->sr)) & MMCI_BIT(CMDRDY)));
if (status & error_flags) {
dump_cmd(cmdr, cmd->cmdarg, status, "Command Failed");
return COMM_ERR;
}
/* Copy the response to the response buffer */
if (cmd->resp_type & MMC_RSP_136) {
cmd->response[0] = readl(&mci->rspr);
cmd->response[1] = readl(&mci->rspr1);
cmd->response[2] = readl(&mci->rspr2);
cmd->response[3] = readl(&mci->rspr3);
} else
cmd->response[0] = readl(&mci->rspr);
/* transfer all of the blocks */
if (data) {
u32 word_count, block_count;
u32* ioptr;
u32 sys_blocksize, dummy, i;
u32 (*mci_data_op)
(atmel_mci_t *mci, u32* data, u32 error_flags);
if (data->flags & MMC_DATA_READ) {
mci_data_op = mci_data_read;
sys_blocksize = mmc->read_bl_len;
ioptr = (u32*)data->dest;
} else {
mci_data_op = mci_data_write;
sys_blocksize = mmc->write_bl_len;
ioptr = (u32*)data->src;
}
status = 0;
for (block_count = 0;
block_count < data->blocks && !status;
block_count++) {
word_count = 0;
do {
status = mci_data_op(mci, ioptr, error_flags);
word_count++;
ioptr++;
} while (!status && word_count < (data->blocksize/4));
#ifdef DEBUG
if (data->flags & MMC_DATA_READ)
{
printf("Read Data:\n");
print_buffer(0, data->dest, 1,
word_count*4, 0);
}
#endif
#ifdef DEBUG
if (!status && word_count < (sys_blocksize / 4))
printf("filling rest of block...\n");
#endif
/* fill the rest of a full block */
while (!status && word_count < (sys_blocksize / 4)) {
status = mci_data_op(mci, &dummy,
error_flags);
word_count++;
}
if (status) {
dump_cmd(cmdr, cmd->cmdarg, status,
"Data Transfer Failed");
return COMM_ERR;
}
}
/* Wait for Transfer End */
i = 0;
do {
status = readl(&mci->sr);
if (status & error_flags) {
dump_cmd(cmdr, cmd->cmdarg, status,
"DTIP Wait Failed");
return COMM_ERR;
}
i++;
} while ((status & MMCI_BIT(DTIP)) && i < 10000);
if (status & MMCI_BIT(DTIP)) {
dump_cmd(cmdr, cmd->cmdarg, status,
"XFER DTIP never unset, ignoring");
}
}
return 0;
}
