//*****************************************************************************
//
// This is the main loop that runs the application.
//
//*****************************************************************************
int
main(void)
{
#ifdef DMA_MODE
MMUConfigAndEnable();
/* Enable Data Cache */
CacheEnable(CACHE_DCACHE);
#endif
//
//USB module clock enable
//
USB0ModuleClkConfig();
//
//USB Interrupt enable
//
USBInterruptEnable();
//
//Delay timer setup
//
DelayTimerSetup();
//
// Initialize the idle timeout and reset all flags.
//
//g_ulIdleTimeout = 0;
g_ulFlags = 0;
//
// Initialize the state to idle.
//
g_eMSCState = MSC_DEV_IDLE;
USBDMSCInit(0, (tUSBDMSCDevice *)&g_sMSCDevice);
#ifdef DMA_MODE
Cppi41DmaInit(USB_INSTANCE, epInfo, NUMBER_OF_ENDPOINTS);
for(;g_bufferIndex < NUM_OF_RX_BDs; g_bufferIndex++)
{
dataBuffer = (unsigned char *)cppiDmaAllocBuffer();
doDmaRxTransfer(USB_INSTANCE, USB_MSC_BUFER_SIZE, dataBuffer,
g_sMSCDevice.psPrivateData->ucOUTEndpoint);
}
#endif
//
// Drop into the main loop.
//
while(1);
}
int main(void)
{
/* Setup the MMU and do necessary MMU configurations. */
MMUConfigAndEnable();
/* Enable all levels of CACHE. */
CacheEnable(CACHE_ALL);
/* Initialize the UART console */
ConsoleUtilsInit();
/* Select the console type based on compile time check */
ConsoleUtilsSetType(CONSOLE_UART);
ConsoleUtilsPrintf("McASP Example Application. ");
ConsoleUtilsPrintf("Please connect headphone/speaker to the LINE OUT");
ConsoleUtilsPrintf(" of the EVM to listen to the audio tone.");
/* Enable the module clock for I2C0 Instance. */
I2C0ModuleClkConfig();
/* Set up the pin mux for I2C0 instance. */
I2CPinMuxSetup(0);
/* Enable the module clock for McASP1 Instance. */
McASP1ModuleClkConfig();
/* Enable pin-mux for McASP1 instance. */
McASP1PinMuxSetup();
/* Enable the EDMA module clocks. */
EDMAModuleClkConfig();
/* Initialize the ARM Interrupt Controller.*/
IntAINTCInit();
/* Enable EDMA Interrupt. */
EDMA3IntSetup();
/* Enable McASP Interrupt. */
McASPIntSetup();
/* Initialize the I2C interface for the codec AIC31 */
I2CCodecIfInit(I2C_INST_BASE, I2C_SLAVE_CODEC_AIC31);
/* Enable the interrupts generation at global level */
IntMasterIRQEnable();
/* Configure the Codec for I2S mode */
AudioCodecInit();
/* Initialize the looping of tone. */
ToneLoopInit();
/* Start playing tone. */
AudioTxActivate();
while(1);
}
int main(void)
{
unsigned int triggerValue = 0;
unsigned char inputVal = 0u;
/* Setup the MMU and do necessary MMU configurations. */
MMUConfigAndEnable();
/* Enable all levels of CACHE. */
CacheEnable(CACHE_ALL);
/* Initialize the UART console */
ConsoleUtilsInit();
/* Select the console type based on compile time check */
ConsoleUtilsSetType(CONSOLE_UART);
/* Enable the WDT clocks */
WatchdogTimer1ModuleClkConfig();
/* Reset the Watchdog Timer */
WatchdogTimerReset(SOC_WDT_1_REGS);
/* Disable the Watchdog timer */
WatchdogTimerDisable(SOC_WDT_1_REGS);
/* Perform the initial settings for the Watchdog Timer */
WatchdogTimerSetUp();
/* Send the message to UART console */
ConsoleUtilsPrintf("Program Reset!");
ConsoleUtilsPrintf("Input any key at least once in every 4 seconds");
ConsoleUtilsPrintf(" to avoid a further reset.\n\r");
/* Enable the Watchdog Timer */
WatchdogTimerEnable(SOC_WDT_1_REGS);
while(1)
{
/* Wait for an input through console. If no input is given,
** the WDT will timeout and reset will occur.
*/
if(ConsoleUtilsScanf("%c", &inputVal))
{
triggerValue += 1;
/* Write into the trigger register. This will load the value from the
** load register into the counter register and hence timer will start
** from the initial count.
*/
WatchdogTimerTriggerSet(SOC_WDT_1_REGS, triggerValue);
}
}
}
int main(void)
{
MMUConfigAndEnable();
CacheEnable(CACHE_ALL);
IntMasterIRQEnable();
IntAINTCInit();
/* Initialize console for communication with the Host Machine */
ConsoleUtilsInit();
//
//Delay timer setup
//
DelayTimerSetup();
/* Select the console type based on compile time check */
ConsoleUtilsSetType(CONSOLE_UART);
ConsoleUtilsPrintf("LCDC Controller\r\n");
LCDAINTCConfigure();
LCDBackLightEnable();
SetUpLCD();
/* Configuring the base ceiling */
RasterDMAFBConfig(LCDC_INSTANCE,
(unsigned int)curr_image,
(unsigned int)curr_image + sizeof(image1) - 2,
0);
RasterDMAFBConfig(LCDC_INSTANCE,
(unsigned int)curr_image,
(unsigned int)curr_image + sizeof(image1) - 2,
1);
/* Enable End of frame0/frame1 interrupt */
RasterIntEnable(LCDC_INSTANCE, RASTER_END_OF_FRAME0_INT |
RASTER_END_OF_FRAME1_INT);
/* Enable raster */
RasterEnable(LCDC_INSTANCE);
while(1) {
if (curr_image == image1) {
curr_image = image2;
} else {
curr_image = image1;
}
delay(5000);
}
}
int main(void)
{
unsigned int triggerValue = 0;
/* Setup the MMU and do necessary MMU configurations. */
MMUConfigAndEnable();
/* Enable all levels of CACHE. */
CacheEnable(CACHE_ALL);
/* Set up the UART2 peripheral */
UARTStdioInit();
/* Enable the WDT clocks */
WatchdogTimer1ModuleClkConfig();
/* Reset the Watchdog Timer */
WatchdogTimerReset(SOC_WDT_1_REGS);
/* Disable the Watchdog timer */
WatchdogTimerDisable(SOC_WDT_1_REGS);
/* Perform the initial settings for the Watchdog Timer */
WatchdogTimerSetUp();
/* Send the message to UART console */
UARTPuts("Program Reset!", -1);
UARTPuts("Input any key at least once in every 4 seconds to avoid a further reset.\n\r", -1);
/* Enable the Watchdog Timer */
WatchdogTimerEnable(SOC_WDT_1_REGS);
while(1)
{
/* Wait for an input through UART. If no input is given,
** the WDT will timeout and reset will occur.
*/
if(UARTGetc())
{
triggerValue += 1;
/* Write into the trigger register. This will load the value from the
** load register into the counter register and hence timer will start
** from the initial count.
*/
WatchdogTimerTriggerSet(SOC_WDT_1_REGS, triggerValue);
}
}
}
//*****************************************************************************
//
// This is the main loop that runs the application.
//
//*****************************************************************************
int
main(void)
{
unsigned int i;
unsigned char *src, *dest;
/* MMU needs to be turned on to provide HW support unaligned
access to USB structures */
MMUConfigAndEnable();
/* Enable Data Cache */
CacheEnable(CACHE_ALL);
//
//USB module clock enable
//
USB0ModuleClkConfig();
//
//USB Interrupt enable
//
USBInterruptEnable();
//
//Delay timer setup
//
DelayTimerSetup();
CacheDataCleanInvalidateAll();
USBDMSCInit(0, (tUSBDMSCDevice *)&g_sMSCDevice);
#ifdef DMA_MODE
Cppi41DmaInit(USB_INSTANCE, epInfo, NUMBER_OF_ENDPOINTS);
for(;g_bufferIndex < NUM_OF_RX_BDs; g_bufferIndex++)
{
dataBuffer = (unsigned char *)cppiDmaAllocBuffer();
doDmaRxTransfer(USB_INSTANCE, USB_MSC_BUFER_SIZE, dataBuffer,
g_sMSCDevice.psPrivateData->ucOUTEndpoint);
}
#endif
while(1)
{
}
}
int main(void)
{
MMUConfigAndEnable();
CacheEnable(CACHE_ALL);
SetupIntc();
UARTStdioInit();
/* This function will enable clocks for the DMTimer2 instance */
DMTimer2ModuleClkConfig();
TouchScreenInit();
return 0;
}
/*
** The main function
*/
int main(void)
{
unsigned int ipAddr;
LWIP_IF lwipIfPort1, lwipIfPort2;
MMUConfigAndEnable();
#ifdef LWIP_CACHE_ENABLED
CacheEnable(CACHE_ALL);
#endif
CPSWPinMuxSetup();
CPSWClkEnable();
/* Initialize console for communication with the Host Machine */
ConsoleUtilsInit();
/* Select the console type based on compile time check */
ConsoleUtilsSetType(CONSOLE_UART);
/* Chip configuration RGMII selection */
EVMPortMIIModeSelect();
/* Get the MAC address */
EVMMACAddrGet(0, lwipIfPort1.macArray);
EVMMACAddrGet(1, lwipIfPort2.macArray);
AintcCPSWIntrSetUp();
//DelayTimerSetup();
ConsoleUtilsPrintf("\n\rStarterWare Ethernet Echo Application. \n\r\n\r" );
ConsoleUtilsPrintf("Acquiring IP Address for Port 1... \n\r" );
#if STATIC_IP_ADDRESS_PORT1
lwipIfPort1.instNum = 0;
lwipIfPort1.slvPortNum = 1;
lwipIfPort1.ipAddr = STATIC_IP_ADDRESS_PORT1;
lwipIfPort1.netMask = 0;
lwipIfPort1.gwAddr = 0;
lwipIfPort1.ipMode = IPADDR_USE_STATIC;
ipAddr = lwIPInit(&lwipIfPort1);
#else
lwipIfPort1.instNum = 0;
lwipIfPort1.slvPortNum = 1;
lwipIfPort1.ipAddr = 0;
lwipIfPort1.netMask = 0;
lwipIfPort1.gwAddr = 0;
lwipIfPort1.ipMode = IPADDR_USE_DHCP;
ipAddr = lwIPInit(&lwipIfPort1);
#endif
if(ipAddr)
{
ConsoleUtilsPrintf("\n\r\n\rPort 1 IP Address Assigned: ");
IpAddrDisplay(ipAddr);
}
else
{
ConsoleUtilsPrintf("\n\r\n\rPort 1 IP Address Acquisition Failed.");
}
/* Initialize the sample httpd server. */
echo_init();
/* Loop forever. All the work is done in interrupt handlers. */
while(1)
{
; /* Perform nothing */
}
}
//*****************************************************************************
//
// This is the main application entry function.
//
//*****************************************************************************
int
main(void)
{
unsigned int ulTxCount;
unsigned int ulRxCount;
tRectangle sRect;
char pcBuffer[16];
unsigned int ulFullness;
unsigned int intFlags = 0;
unsigned char Intstatus;
unsigned int i;
unsigned char *src, *dest;
MMUConfigAndEnable();
//
// Not configured initially.
//
g_bUSBConfigured = false;
//
//configures arm interrupt controller to generate raster interrupt
//
USBInterruptEnable();
//
//LCD Back light setup
//
LCDBackLightEnable();
//
//UPD Pin setup
//
UPDNPinControl();
//
//Delay timer setup
//
DelayTimerSetup();
//
//Configures raster to display image
//
SetUpLCD();
RasterDMAFBConfig(SOC_LCDC_0_REGS,
(unsigned int)(g_pucBuffer+PALETTE_OFFSET),
(unsigned int)(g_pucBuffer+PALETTE_OFFSET) + sizeof(g_pucBuffer) - 2 -
PALETTE_OFFSET, FRAME_BUFFER_0);
RasterDMAFBConfig(SOC_LCDC_0_REGS,
(unsigned int)(g_pucBuffer+PALETTE_OFFSET),
(unsigned int)(g_pucBuffer+PALETTE_OFFSET) + sizeof(g_pucBuffer) - 2 -
PALETTE_OFFSET, FRAME_BUFFER_1);
src = (unsigned char *) palette_32b;
dest = (unsigned char *) (g_pucBuffer+PALETTE_OFFSET);
// Copy palette info into buffer
for( i = PALETTE_OFFSET; i < (PALETTE_SIZE+PALETTE_OFFSET); i++)
{
*dest++ = *src++;
}
GrOffScreen24BPPInit(&g_s35_480x272x24Display, g_pucBuffer, LCD_WIDTH, LCD_HEIGHT);
// Initialize a drawing context.
GrContextInit(&g_sContext, &g_s35_480x272x24Display);
/* enable End of frame interrupt */
RasterEndOfFrameIntEnable(SOC_LCDC_0_REGS);
/* enable raster */
RasterEnable(SOC_LCDC_0_REGS);
//
// Fill the top 24 rows of the screen with blue to create the banner.
//
sRect.sXMin = 0;
sRect.sYMin = 0;
sRect.sXMax = GrContextDpyWidthGet(&g_sContext) - 1;
sRect.sYMax = 23;
GrContextForegroundSet(&g_sContext, ClrDarkBlue);
GrRectFill(&g_sContext, &sRect);
//
// Put a white box around the banner.
//
GrContextForegroundSet(&g_sContext, ClrWhite);
GrRectDraw(&g_sContext, &sRect);
//
// Put the application name in the middle of the banner.
//
GrContextFontSet(&g_sContext, &g_sFontCm20);
GrStringDrawCentered(&g_sContext, "usb-dev-serial", -1,
GrContextDpyWidthGet(&g_sContext) / 2, 10, 0);
//
// Show the various static text elements on the color STN display.
//
GrContextFontSet(&g_sContext, TEXT_FONT);
GrStringDraw(&g_sContext, "Tx bytes:", -1, 8, 80, false);
GrStringDraw(&g_sContext, "Tx buffer:", -1, 8, 105, false);
GrStringDraw(&g_sContext, "Rx bytes:", -1, 8, 160, false);
GrStringDraw(&g_sContext, "Rx buffer:", -1, 8, 185, false);
DrawBufferMeter(&g_sContext, 150, 105);
DrawBufferMeter(&g_sContext, 150, 185);
//
// Tell the user what we are up to.
//
DisplayStatus(&g_sContext, " Configuring USB... ");
//
//Initialize the Rx and TX Buffers
//
USBBufferInit((tUSBBuffer *)&g_sTxBuffer);
USBBufferInit((tUSBBuffer *)&g_sRxBuffer);
//
// Pass our device information to the USB library and place the device
// on the bus.
//
USBDCDCInit(0, (tUSBDCDCDevice *)&g_sCDCDevice);
//
// Wait for initial configuration to complete.
//
DisplayStatus(&g_sContext, " Waiting for host... ");
//
// Clear our local byte counters.
//
ulRxCount = 0;
ulTxCount = 0;
/* Configuring the system clocks for UART0 instance. */
UART0ModuleClkConfig();
/* Performing the Pin Multiplexing for UART0 instance. */
UARTPinMuxSetup(0);
/* Performing a module reset. */
UARTModuleReset(SOC_UART_0_REGS);
/* Performing Baud Rate settings. */
UartBaudRateSet();
/* Switching to Configuration Mode B. */
UARTRegConfigModeEnable(SOC_UART_0_REGS, UART_REG_CONFIG_MODE_B);
/* Programming the Line Characteristics. */
UARTLineCharacConfig(SOC_UART_0_REGS,
(UART_FRAME_WORD_LENGTH_8 | UART_FRAME_NUM_STB_1),
UART_PARITY_NONE);
/* Disabling write access to Divisor Latches. */
UARTDivisorLatchDisable(SOC_UART_0_REGS);
/* Disabling Break Control. */
UARTBreakCtl(SOC_UART_0_REGS, UART_BREAK_COND_DISABLE);
/* Switching to UART16x operating mode. */
UARTOperatingModeSelect(SOC_UART_0_REGS, UART16x_OPER_MODE);
/* Performing FIFO configurations. */
UartFIFOConfigure();
/* Preparing the 'intFlags' variable to be passed as an argument.*/
intFlags |= (UART_INT_LINE_STAT | UART_INT_RHR_CTI);
/* Enable the Interrupts in UART.*/
UARTIntEnable(SOC_UART_0_REGS, intFlags);
//
// Main application loop.
//
while(1)
{
//
// Have we been asked to update the status display?
//
if(g_ulFlags & COMMAND_STATUS_UPDATE)
{
//
// Clear the command flag
//
Intstatus = IntDisable();
g_ulFlags &= ~COMMAND_STATUS_UPDATE;
IntEnable(Intstatus);
DisplayStatus(&g_sContext, g_pcStatus);
}
//
// Has there been any transmit traffic since we last checked?
//
if(ulTxCount != g_ulUARTTxCount)
{
//
// Take a snapshot of the latest transmit count.
//
ulTxCount = g_ulUARTTxCount;
//
// Update the display of bytes transmitted by the UART.
//
usnprintf(pcBuffer, 16, "%d ", ulTxCount);
GrStringDraw(&g_sContext, pcBuffer, -1, 150, 80, true);
//
// Update the RX buffer fullness. Remember that the buffers are
// named relative to the USB whereas the status display is from
// the UART's perspective. The USB's receive buffer is the UART's
// transmit buffer.
//
ulFullness = ((USBBufferDataAvailable(&g_sRxBuffer) * 100) /
UART_BUFFER_SIZE);
UpdateBufferMeter(&g_sContext, ulFullness, 150, 105);
}
//
// Has there been any receive traffic since we last checked?
//
if(ulRxCount != g_ulUARTRxCount)
{
//
// Take a snapshot of the latest receive count.
//
ulRxCount = g_ulUARTRxCount;
//
// Update the display of bytes received by the UART.
//
usnprintf(pcBuffer, 16, "%d ", ulRxCount);
GrStringDraw(&g_sContext, pcBuffer, -1, 150, 160, true);
//
// Update the TX buffer fullness. Remember that the buffers are
// named relative to the USB whereas the status display is from
// the UART's perspective. The USB's transmit buffer is the UART's
// receive buffer.
//
ulFullness = ((USBBufferDataAvailable(&g_sTxBuffer) * 100) /
UART_BUFFER_SIZE);
UpdateBufferMeter(&g_sContext, ulFullness, 150, 185);
}
}
}
//*****************************************************************************
//
// This is the main loop that runs the application.
//
//*****************************************************************************
int
main(void)
{
tRectangle sRect;
unsigned int i;
unsigned char *src, *dest;
MMUConfigAndEnable();
//
//configures arm interrupt controller to generate raster interrupt
//
USBInterruptEnable(USB_INSTANCE);
//
//LCD back light setup
//
LCDBackLightEnable();
//
//UPD Pin setup
//
UPDNPinControl();
//
//Delay timer setup
//
DelayTimerSetup();
//
//Configures raster to display image
//
SetUpLCD();
/* configuring the base ceiling */
RasterDMAFBConfig(SOC_LCDC_0_REGS,
(unsigned int)(g_pucBuffer+PALETTE_OFFSET),
(unsigned int)(g_pucBuffer+PALETTE_OFFSET) + sizeof(g_pucBuffer) - 2 -
PALETTE_OFFSET, FRAME_BUFFER_0);
RasterDMAFBConfig(SOC_LCDC_0_REGS,
(unsigned int)(g_pucBuffer+PALETTE_OFFSET),
(unsigned int)(g_pucBuffer+PALETTE_OFFSET) + sizeof(g_pucBuffer) - 2 -
PALETTE_OFFSET, FRAME_BUFFER_1);
src = (unsigned char *) palette_32b;
dest = (unsigned char *) (g_pucBuffer+PALETTE_OFFSET);
// Copy palette info into buffer
for( i = PALETTE_OFFSET; i < (PALETTE_SIZE+PALETTE_OFFSET); i++)
{
*dest++ = *src++;
}
GrOffScreen24BPPInit(&g_s35_800x480x24Display, g_pucBuffer, LCD_WIDTH, LCD_HEIGHT);
// Initialize a drawing context.
GrContextInit(&g_sContext, &g_s35_800x480x24Display);
/* enable End of frame interrupt */
RasterEndOfFrameIntEnable(SOC_LCDC_0_REGS);
/* enable raster */
RasterEnable(SOC_LCDC_0_REGS);
//
// Fill the top 15 rows of the screen with blue to create the banner.
//
sRect.sXMin = 0;
sRect.sYMin = 0;
sRect.sXMax = GrContextDpyWidthGet(&g_sContext) - 1;
sRect.sYMax = DISPLAY_BANNER_HEIGHT;
//
// Set the banner background.
//
GrContextForegroundSet(&g_sContext, DISPLAY_BANNER_BG);
GrRectFill(&g_sContext, &sRect);
//
// Put a white box around the banner.
//
GrContextForegroundSet(&g_sContext, DISPLAY_BANNER_FG);
GrRectDraw(&g_sContext, &sRect);
//
// Put the application name in the middle of the banner.
//
GrContextFontSet(&g_sContext, &g_sFontCm20);
GrStringDrawCentered(&g_sContext, "usb_host_mouse", -1,
GrContextDpyWidthGet(&g_sContext) / 2, 10, 0);
//
// Register the host class drivers.
//
USBHCDRegisterDrivers(USB_INSTANCE, g_ppHostClassDrivers, g_ulNumHostClassDrivers);
//
// Initialized the cursor.
//
g_ulButtons = 0;
g_sCursor.sXMin = GrContextDpyWidthGet(&g_sContext) / 2;
g_sCursor.sXMax = g_sCursor.sXMin + DISPLAY_MOUSE_SIZE;
g_sCursor.sYMin = GrContextDpyHeightGet(&g_sContext) / 2;
g_sCursor.sYMax = g_sCursor.sYMin + DISPLAY_MOUSE_SIZE;
//
// Update the status on the screen.
//
UpdateStatus();
//
// Update the cursor once to display it.
//
UpdateCursor(0, 0);
//
// Open an instance of the mouse driver. The mouse does not need
// to be present at this time, this just saves a place for it and allows
// the applications to be notified when a mouse is present.
//
g_ulMouseInstance =
USBHMouseOpen(USB_INSTANCE, MouseCallback, g_pucMouseBuffer, MOUSE_MEMORY_SIZE);
//
// Initialize the power configuration. This sets the power enable signal
// to be active high and does not enable the power fault.
//
USBHCDPowerConfigInit(USB_INSTANCE, USBHCD_VBUS_AUTO_HIGH);
//
// Initialize the host controller stack.
//
USBHCDInit(USB_INSTANCE, g_pHCDPool, HCD_MEMORY_SIZE);
//
// Call the main loop for the Host controller driver.
//
USBHCDMain(USB_INSTANCE, g_ulMouseInstance);
//
// The main loop for the application.
//
while(1)
{
switch(eUSBState)
{
//
// This state is entered when the mouse is first detected.
//
case STATE_MOUSE_INIT:
{
//
// Initialize the newly connected mouse.
//
USBHMouseInit(g_ulMouseInstance);
//
// Proceed to the mouse connected state.
//
eUSBState = STATE_MOUSE_CONNECTED;
//
// Update the status on the screen.
//
UpdateStatus();
break;
}
case STATE_MOUSE_CONNECTED:
{
//
// Nothing is currently done in the main loop when the mouse
// is connected.
//
break;
}
case STATE_NO_DEVICE:
{
//
// The mouse is not connected so nothing needs to be done here.
//
break;
}
default:
{
break;
}
}
//
// Periodically call the main loop for the Host controller driver.
//
USBHCDMain(USB_INSTANCE, g_ulMouseInstance);
}
}
/*****************************************************************************
*
* This is the main loop that runs the application.
*
*****************************************************************************/
int
main(void)
{
tRectangle sRect;
MMUConfigAndEnable();
/* Enable USB module clock */
USB0ModuleClkConfig();
/* Enable DM timer 3 module clock */
DMTimer3ModuleClkConfig();
/* Enbale touch screen module colock */
TSCADCModuleClkConfig();
/* Enable touch screen ADC pinmux */
TSCADCPinMuxSetUp();
/* configures arm interrupt controller to generate raster interrupt */
USBInterruptEnable();
/* LCD Back light setup */
LCDBackLightEnable();
/* UPD Pin setup */
UPDNPinControl();
/* Delay timer setup */
DelayTimerSetup();
/* Configures raster to display image */
SetUpLCD();
/* Register touch scren interrupt */
TouchIntRegister();
IntSystemEnable(SYS_INT_TINT3);
IntPrioritySet(SYS_INT_TINT3, 0, AINTC_HOSTINT_ROUTE_IRQ);
IntSystemEnable(SYS_INT_ADC_TSC_GENINT);
IntPrioritySet(SYS_INT_ADC_TSC_GENINT, 0, AINTC_HOSTINT_ROUTE_IRQ);
/* Configures raster to display image and Copy palette info into buffer */
LCDInit();
GrOffScreen24BPPInit(&g_s35_480x272x24Display, g_pucBuffer, LCD_WIDTH, LCD_HEIGHT);
/* Initialize a drawing context. */
GrContextInit(&g_sContext, &g_s35_480x272x24Display);
/* enable End of frame interrupt */
RasterEndOfFrameIntEnable(SOC_LCDC_0_REGS);
/* enable raster */
RasterEnable(SOC_LCDC_0_REGS);
/* Fill the top 24 rows of the screen with blue to create the banner. */
sRect.sXMin = 0;
sRect.sYMin = 0;
sRect.sXMax = GrContextDpyWidthGet(&g_sContext) - 1;
sRect.sYMax = (MAX_ROW_NUM - 1);
GrContextForegroundSet(&g_sContext, ClrDarkBlue);
GrRectFill(&g_sContext, &sRect);
/* Put a white box around the banner. */
GrContextForegroundSet(&g_sContext, ClrWhite);
GrRectDraw(&g_sContext, &sRect);
/* Put the application name in the middle of the banner. */
GrContextFontSet(&g_sContext, &g_sFontCm20);
GrStringDrawCentered(&g_sContext, "usb-dev-composite", -1,
GrContextDpyWidthGet(&g_sContext) / 2, 10, 0);
sRect.sXMin = 0;
sRect.sYMin = (MAX_ROW_NUM + 1);
sRect.sXMax = GrContextDpyWidthGet(&g_sContext) - 1;
sRect.sYMax = GrContextDpyHeightGet(&g_sContext) - BUTTON_HEIGHT - 2;
GrContextForegroundSet(&g_sContext, ClrBlack);
GrRectFill(&g_sContext, &sRect);
/* Put a white box around the banner. */
GrContextForegroundSet(&g_sContext, ClrRed);
GrRectDraw(&g_sContext, &sRect);
/* Draw the buttons in their initial (unpressed)state. */
UpdateDisplay(g_ucButtons, true);
/* Show the various static text elements on the color STN display. */
GrContextFontSet(&g_sContext, TEXT_FONT);
GrStringDraw(&g_sContext, "Tx bytes:", -1, CDC_STR_X_POSITION,
CDC_STR_Y_POSITION, false);
GrStringDraw(&g_sContext, "Tx buffer:", -1, CDC_STR_X_POSITION,
(CDC_STR_Y_POSITION + CDC_STR_Y_DIFF), false);
GrStringDraw(&g_sContext, "Rx bytes:", -1, CDC_STR_X_POSITION,
(CDC_STR_Y_POSITION + (CDC_STR_Y_DIFF * 3)), false);
GrStringDraw(&g_sContext, "Rx buffer:", -1, CDC_STR_X_POSITION,
(CDC_STR_Y_POSITION + (CDC_STR_Y_DIFF * 4)), false);
DrawBufferMeter(&g_sContext, BUFFER_METER_X_POS, BUFFER_METER_Y_POS);
DrawBufferMeter(&g_sContext, BUFFER_METER_X_POS,
(BUFFER_METER_Y_POS + CDC_BUF_METER_Y_DIFF));
/* Tell the user what we are up to. */
DisplayStatus(&g_sContext, " Waiting for host... ");
/* Initialize touch screen */
TouchInit();
/* Touch screen Interrupt enbale */
TouchIntEnable();
/* Touch Screen Enable */
TouchEnable();
/* Pass the USB library our device information, initialize the USB
controller and connect the device to the bus.
*/
g_psCompDevices[0].pvInstance =
USBDHIDMouseCompositeInit(0, (tUSBDHIDMouseDevice *)&g_sMouseDevice);
g_psCompDevices[1].pvInstance =
USBDCDCCompositeInit(0, (tUSBDCDCDevice *)&g_sCDCDevice);
/* Pass the device information to the USB library and place the device
on the bus.
*/
USBDCompositeInit(0, &g_sCompDevice, DESCRIPTOR_DATA_SIZE,
g_pucDescriptorData);
/* Initialize the mouse and serial devices. */
SerialInit();
/* Drop into the main loop. */
while(1)
{
/* Allow the main serial routine to run. */
SerialMain();
/* Allow the main mouse routine to run. */
MouseMain();
}
}
/*
** Main function.
*/
int main(void)
{
unsigned int numByteChunks = 0;
unsigned char *pBuffer = NULL;
unsigned int remainBytes = 0;
/* Configure and enable the MMU. */
MMUConfigAndEnable();
/* Enable all levels of Cache. */
CacheEnable(CACHE_ALL);
/* Configuring the system clocks for EDMA. */
EDMAModuleClkConfig();
/* Configuring the system clocks for UART0 instance. */
UART0ModuleClkConfig();
/* Performing Pin Multiplexing for UART0 instance. */
UARTPinMuxSetup(0);
/* Enabling IRQ in CPSR of ARM processor. */
IntMasterIRQEnable();
/* Initializing the ARM Interrupt Controller. */
IntAINTCInit();
/* Initializing the EDMA. */
EDMA3Initialize();
/* Initializing the UART0 instance for use. */
UARTInitialize();
/* Select the console type based on compile time check */
ConsoleUtilsSetType(CONSOLE_UART);
/*
** Configuring the EDMA.
*/
/* Request DMA Channel and TCC for UART Transmit*/
EDMA3RequestChannel(SOC_EDMA30CC_0_REGS, EDMA3_CHANNEL_TYPE_DMA,
EDMA3_UART_TX_CHA_NUM, EDMA3_UART_TX_CHA_NUM,
EVT_QUEUE_NUM);
/* Registering Callback Function for TX*/
cb_Fxn[EDMA3_UART_TX_CHA_NUM] = &callback;
/* Request DMA Channel and TCC for UART Receive */
EDMA3RequestChannel(SOC_EDMA30CC_0_REGS, EDMA3_CHANNEL_TYPE_DMA,
EDMA3_UART_RX_CHA_NUM, EDMA3_UART_RX_CHA_NUM,
EVT_QUEUE_NUM);
/* Registering Callback Function for RX*/
cb_Fxn[EDMA3_UART_RX_CHA_NUM] = &callback;
/******************** Transmission of a string **************************/
numByteChunks = (sizeof(welcome) - 1) / txBytesPerEvent;
remainBytes = (sizeof(welcome) - 1) % txBytesPerEvent;
/* Configuring EDMA PaRAM sets to transmit data. */
UARTTxEDMAPaRAMSetConfig(welcome,
numByteChunks * txBytesPerEvent,
EDMA3_UART_TX_CHA_NUM,
EDMA3CC_OPT(DUMMY_CH_NUM),
EDMA3_UART_TX_CHA_NUM);
/* Configuring the PaRAM set for Dummy Transfer. */
TxDummyPaRAMConfEnable();
/* Enable EDMA Transfer */
EDMA3EnableTransfer(SOC_EDMA30CC_0_REGS, EDMA3_UART_TX_CHA_NUM,
EDMA3_TRIG_MODE_EVENT);
/* Wait for return from callback */
while(0 == clBackFlag);
clBackFlag = 0;
/* Remaining bytes are transferred through polling method. */
if(0 != remainBytes)
{
pBuffer = welcome + (sizeof(welcome) - 1) - remainBytes;
UARTPuts((char*)pBuffer, remainBytes);
}
/******************** Transmission of a string **************************/
numByteChunks = (sizeof(intent) - 1) / txBytesPerEvent;
remainBytes = (sizeof(intent) - 1) % txBytesPerEvent;
/* Enabling DMA Mode 1. */
UARTDMAEnable(UART_INSTANCE_BASE_ADD, UART_DMA_MODE_1_ENABLE);
/* Configuring EDMA PaRAM sets to transmit data. */
UARTTxEDMAPaRAMSetConfig(intent,
numByteChunks * txBytesPerEvent,
EDMA3_UART_TX_CHA_NUM,
EDMA3CC_OPT(DUMMY_CH_NUM),
EDMA3_UART_TX_CHA_NUM);
/* Configuring the PaRAM set for Dummy Transfer. */
TxDummyPaRAMConfEnable();
/* Enable EDMA Transfer */
EDMA3EnableTransfer(SOC_EDMA30CC_0_REGS, EDMA3_UART_TX_CHA_NUM,
EDMA3_TRIG_MODE_EVENT);
/* Wait for return from callback */
while(0 == clBackFlag);
clBackFlag = 0;
/* Remaining bytes are transferred through polling method. */
if(0 != remainBytes)
{
pBuffer = intent + (sizeof(intent) - 1) - remainBytes;
UARTPuts((char*)pBuffer, remainBytes);
}
/******************** Transmission of a string **************************/
numByteChunks = (sizeof(enter) - 1) / txBytesPerEvent;
remainBytes = (sizeof(enter) - 1) % txBytesPerEvent;
/* Enabling DMA Mode 1. */
UARTDMAEnable(UART_INSTANCE_BASE_ADD, UART_DMA_MODE_1_ENABLE);
/* Configuring EDMA PaRAM sets to transmit data. */
UARTTxEDMAPaRAMSetConfig(enter,
numByteChunks * txBytesPerEvent,
EDMA3_UART_TX_CHA_NUM,
EDMA3CC_OPT(DUMMY_CH_NUM),
EDMA3_UART_TX_CHA_NUM);
/* Configuring the PaRAM set for Dummy Transfer. */
TxDummyPaRAMConfEnable();
/* Enable EDMA Transfer */
EDMA3EnableTransfer(SOC_EDMA30CC_0_REGS, EDMA3_UART_TX_CHA_NUM,
EDMA3_TRIG_MODE_EVENT);
/* Wait for return from callback */
while(0 == clBackFlag);
clBackFlag = 0;
/* Remaining bytes are transferred through polling method. */
if(0 != remainBytes)
{
pBuffer = enter + (sizeof(enter) - 1) - remainBytes;
UARTPuts((char*)pBuffer, remainBytes);
}
/********************* Receiving Data from User *************************/
/* Enabling DMA Mode 1. */
UARTDMAEnable(UART_INSTANCE_BASE_ADD, UART_DMA_MODE_1_ENABLE);
/* Configuring the PaRAM set for reception. */
UARTRxEDMAPaRAMSetConfig(rxBuffer,
NUM_RX_BYTES,
EDMA3_UART_RX_CHA_NUM,
0xFFFF,
EDMA3_UART_RX_CHA_NUM);
/* Enable EDMA Transfer */
EDMA3EnableTransfer(SOC_EDMA30CC_0_REGS, EDMA3_UART_RX_CHA_NUM,
EDMA3_TRIG_MODE_EVENT);
/* Wait for return from callback */
while(0 == clBackFlag);
clBackFlag = 0;
/******************* Echoing received bytes *****************************/
numByteChunks = (NUM_RX_BYTES) / txBytesPerEvent;
remainBytes = (NUM_RX_BYTES) % txBytesPerEvent;
/* Enabling DMA Mode 1. */
UARTDMAEnable(UART_INSTANCE_BASE_ADD, UART_DMA_MODE_1_ENABLE);
/* Configuring EDMA PaRAM sets to transmit data. */
UARTTxEDMAPaRAMSetConfig(rxBuffer,
numByteChunks * txBytesPerEvent,
EDMA3_UART_TX_CHA_NUM,
EDMA3CC_OPT(DUMMY_CH_NUM),
EDMA3_UART_TX_CHA_NUM);
/* Configuring the PaRAM set for Dummy Transfer. */
TxDummyPaRAMConfEnable();
/* Enable EDMA Transfer */
EDMA3EnableTransfer(SOC_EDMA30CC_0_REGS, EDMA3_UART_TX_CHA_NUM,
EDMA3_TRIG_MODE_EVENT);
/* Wait for return from callback */
while(0 == clBackFlag);
clBackFlag = 0;
/* Remaining bytes are transferred through polling method. */
if(0 != remainBytes)
{
pBuffer = rxBuffer + NUM_RX_BYTES - remainBytes;
UARTPuts((char*)pBuffer, remainBytes);
}
/******************* Freeing of allocated channels **********************/
/* Free EDMA3 Channels for TX and RX */
EDMA3FreeChannel(SOC_EDMA30CC_0_REGS, EDMA3_CHANNEL_TYPE_DMA,
EDMA3_UART_TX_CHA_NUM, EDMA3_TRIG_MODE_EVENT,
EDMA3_UART_TX_CHA_NUM, EVT_QUEUE_NUM);
EDMA3FreeChannel(SOC_EDMA30CC_0_REGS, EDMA3_CHANNEL_TYPE_DMA,
EDMA3_UART_RX_CHA_NUM, EDMA3_TRIG_MODE_EVENT,
EDMA3_UART_RX_CHA_NUM, EVT_QUEUE_NUM);
/* Support for Automation Testing. */
PRINT_STATUS(S_PASS);
while(1);
}
int main(void)
{
volatile unsigned int i = 0;
volatile unsigned int initFlg = 1;
/* Setup the MMU and do necessary MMU configurations. */
MMUConfigAndEnable();
/* Enable all levels of CACHE. */
CacheEnable(CACHE_ALL);
/* Initialize console for communication with the Host Machine */
ConsoleUtilsInit();
/*
** Select the console type based on compile time check
** Note: This example is not fully complaint to semihosting. It is
** recommended to use Uart console interface only.
*/
ConsoleUtilsSetType(CONSOLE_UART);
/* Configure the EDMA clocks. */
EDMAModuleClkConfig();
/* Configure EDMA to service the HSMMCSD events. */
HSMMCSDEdmaInit();
/* Perform pin-mux for HSMMCSD pins. */
HSMMCSDPinMuxSetup();
/* Enable module clock for HSMMCSD. */
HSMMCSDModuleClkConfig();
DelayTimerSetup();
#ifdef MMCSD_PERF
PerfTimerSetup();
#endif
/* Basic controller initializations */
HSMMCSDControllerSetup();
/* Initialize the MMCSD controller */
MMCSDCtrlInit(&ctrlInfo);
MMCSDIntEnable(&ctrlInfo);
while(1)
{
if((HSMMCSDCardPresent(&ctrlInfo)) == 1)
{
if(initFlg)
{
HSMMCSDFsMount(0, &sdCard);
initFlg = 0;
Cmd_help(0, NULL);
}
HSMMCSDFsProcessCmdLine();
}
else
{
delay(1);
i = (i + 1) & 0xFFF;
if(i == 1)
{
ConsoleUtilsPrintf("Please insert the card \n\r");
}
if(initFlg != 1)
{
/* Reinitialize all the state variables */
callbackOccured = 0;
xferCompFlag = 0;
dataTimeout = 0;
cmdCompFlag = 0;
cmdTimeout = 0;
/* Initialize the MMCSD controller */
MMCSDCtrlInit(&ctrlInfo);
MMCSDIntEnable(&ctrlInfo);
}
initFlg = 1;
}
}
}
int main(void)
{
tRectangle sRect;
unsigned int i = 0;
unsigned char *src = (unsigned char *) palette_32b;
unsigned char *dest = (unsigned char *) (g_pucBuffer+4);
MMUConfigAndEnable();
//
//Enable USB module clock
//
USB0ModuleClkConfig();
//
//Enable DM timer 3 module clock
//
DMTimer3ModuleClkConfig();
//
//Enbale touch screen module colock
//
TSCADCModuleClkConfig();
//
//Enable touch screen ADC pinmux
//
TSCADCPinMuxSetUp();
//
//Enbale USB interrupts
//
USBInterruptEnable();
//
//Switch ON LCD back light
//
LCDBackLightEnable();
//
//UDP Pin control
//
UPDNPinControl();
//
//Delay timer setup
//
DelayTimerSetup();
//
//Configures raster to display image
//
SetUpLCD();
//
//Register touch scren interrupt
//
TouchIntRegister();
IntSystemEnable(SYS_INT_TINT3);
IntPrioritySet(SYS_INT_TINT3, 0, AINTC_HOSTINT_ROUTE_IRQ);
IntSystemEnable(SYS_INT_ADC_TSC_GENINT);
IntPrioritySet(SYS_INT_ADC_TSC_GENINT, 0, AINTC_HOSTINT_ROUTE_IRQ);
RasterDMAFBConfig(SOC_LCDC_0_REGS,
(unsigned int)(g_pucBuffer+PALETTE_OFFSET),
(unsigned int)(g_pucBuffer+PALETTE_OFFSET) + sizeof(g_pucBuffer) - 2 -
PALETTE_OFFSET, FRAME_BUFFER_0);
RasterDMAFBConfig(SOC_LCDC_0_REGS,
(unsigned int)(g_pucBuffer+PALETTE_OFFSET),
(unsigned int)(g_pucBuffer+PALETTE_OFFSET) + sizeof(g_pucBuffer) - 2 -
PALETTE_OFFSET, FRAME_BUFFER_1);
src = (unsigned char *) palette_32b;
dest = (unsigned char *) (g_pucBuffer+PALETTE_OFFSET);
// Copy palette info into buffer
for( i = PALETTE_OFFSET; i < (PALETTE_SIZE+PALETTE_OFFSET); i++)
{
*dest++ = *src++;
}
GrOffScreen24BPPInit(&g_s35_480x272x24Display, g_pucBuffer, LCD_WIDTH, LCD_HEIGHT);
// Initialize a drawing context.
GrContextInit(&g_sContext, &g_s35_480x272x24Display);
/* enable End of frame interrupt */
RasterEndOfFrameIntEnable(SOC_LCDC_0_REGS);
/* enable raster */
RasterEnable(SOC_LCDC_0_REGS);
//
// Fill the top 24 rows of the screen with blue to create the banner.
//
sRect.sXMin = 0;
sRect.sYMin = 0;
sRect.sXMax = GrContextDpyWidthGet(&g_sContext) - 1;
sRect.sYMax = 23;
GrContextForegroundSet(&g_sContext, ClrDarkBlue);
GrRectFill(&g_sContext, &sRect);
//
// Put a white box around the banner.
//
GrContextForegroundSet(&g_sContext, ClrWhite);
GrRectDraw(&g_sContext, &sRect);
//
// Put the application name in the middle of the banner.
//
GrContextFontSet(&g_sContext, &g_sFontCm20);
GrStringDrawCentered(&g_sContext, "usb-dev-mouse", -1,
GrContextDpyWidthGet(&g_sContext) / 2, 10, 0);
//
// Fill the top 24 rows of the screen with blue to create the banner.
//
sRect.sXMin = 0;
sRect.sYMin = 25;
sRect.sXMax = GrContextDpyWidthGet(&g_sContext) - 1;
sRect.sYMax = GrContextDpyHeightGet(&g_sContext) - BUTTON_HEIGHT - 2;
GrContextForegroundSet(&g_sContext, ClrDarkGray);
GrRectFill(&g_sContext, &sRect);
//
// Put a white box around the banner.
//
GrContextForegroundSet(&g_sContext, ClrRed);
GrRectDraw(&g_sContext, &sRect);
//
// Draw the buttons in their initial (unpressed)state.
//
UpdateDisplay(g_ucButtons, true);
//
//Initialize touch screen
//
TouchInit();
//
//Touch screen Interrupt enbale
//
TouchIntEnable();
//
//Touch Screen Enable
//
TouchEnable();
//
// Initialize the mouse
//
USBDHIDMouseInit(0, (tUSBDHIDMouseDevice *)&g_sMouseDevice);
//
// Drop into the main loop.
//
while(1)
{
//
// Wait for USB configuration to complete.
//
while(!bConnected)
{
}
//
//Wait till someone touches the screen
//
while(!g_iTouch)
{
g_iTouch = TouchDetect();
}
//
//Loop here as long as someone moving the finger/stylus on the touch screen
//
do
{
//
//If so, read the x and Y vlaue and give it to touch handler
//
TouchCoOrdGet(&g_lScreenX, &g_lScreenY);
//
//Call touch handler
//
TouchHandler();
}while(TouchDetect());
//
//Touch is released
//
g_released = 1;
//
//Reset the button status
//
g_ucButtons = 0;
//
//Call the touch handler to update the release status
//
TouchHandler();
//
//Reset the touch flag
//
g_iTouch = 0;
}
}
int main(void)
{
volatile unsigned int i = 0;
volatile unsigned int initFlg = 1;
/* Setup the MMU and do necessary MMU configurations. */
MMUConfigAndEnable();
/* Enable all levels of CACHE. */
CacheEnable(CACHE_ALL);
/* Initialize UART. */
UARTStdioInit();
/* Configure the EDMA clocks. */
EDMAModuleClkConfig();
/* Configure EDMA to service the HSMMCSD events. */
HSMMCSDEdmaInit();
/* Perform pin-mux for HSMMCSD pins. */
HSMMCSDPinMuxSetup();
/* Enable module clock for HSMMCSD. */
HSMMCSDModuleClkConfig();
/* Basic controller initializations */
HSMMCSDControllerSetup();
DelayTimerSetup();
#ifdef MMCSD_PERF
PerfTimerSetup();
#endif
/* Basic controller initializations */
HSMMCSDControllerSetup();
/* Initialize the MMCSD controller */
MMCSDCtrlInit(&ctrlInfo);
MMCSDIntEnable(&ctrlInfo);
while(1)
{
if((HSMMCSDCardPresent(&ctrlInfo)) == 1)
{
if(initFlg)
{
HSMMCSDFsMount(0, &sdCard);
initFlg = 0;
Cmd_help(0, NULL);
}
HSMMCSDFsProcessCmdLine();
}
else
{
delay(1);
i = (i + 1) & 0xFFF;
if(i == 1)
{
UARTPuts("Please insert the card \n\r", -1);
}
if(initFlg != 1)
{
/* Reinitialize all the state variables */
callbackOccured = 0;
xferCompFlag = 0;
dataTimeout = 0;
cmdCompFlag = 0;
cmdTimeout = 0;
/* Initialize the MMCSD controller */
MMCSDCtrlInit(&ctrlInfo);
MMCSDIntEnable(&ctrlInfo);
}
initFlg = 1;
}
}
}
/*****************************************************************************
*
* This is the main loop that runs the application.
*
*****************************************************************************/
int main(void)
{
tRectangle sRect;
MMUConfigAndEnable();
/* Enable USB module clock */
USB0ModuleClkConfig();
/* configures arm interrupt controller to generate raster interrupt */
USBInterruptEnable();
/* LCD Back light setup */
LCDBackLightEnable();
/* UPD Pin setup */
UPDNPinControl();
/* Delay timer setup */
DelayTimerSetup();
/* Configures raster to display image */
SetUpLCD();
/* Configures raster to display image and Copy palette info into buffer */
LCDInit();
GrOffScreen24BPPInit(&g_s35_800x480x24Display, g_pucBuffer, LCD_WIDTH, LCD_HEIGHT);
/* Initialize a drawing context. */
GrContextInit(&g_sContext, &g_s35_800x480x24Display);
/* enable End of frame interrupt */
RasterEndOfFrameIntEnable(SOC_LCDC_0_REGS);
/* enable raster */
RasterEnable(SOC_LCDC_0_REGS);
/* Fill the top 24 rows of the screen with blue to create the banner. */
sRect.sXMin = 0;
sRect.sYMin = 0;
sRect.sXMax = GrContextDpyWidthGet(&g_sContext) - 1;
sRect.sYMax = (MAX_ROW_NUM - 1);
GrContextForegroundSet(&g_sContext, ClrDarkBlue);
GrRectFill(&g_sContext, &sRect);
/* Put a white box around the banner. */
GrContextForegroundSet(&g_sContext, ClrWhite);
GrRectDraw(&g_sContext, &sRect);
/* Put the application name in the middle of the banner. */
GrContextFontSet(&g_sContext, &g_sFontCm20);
GrStringDrawCentered(&g_sContext, "usb-dev-composite", -1,
GrContextDpyWidthGet(&g_sContext) / 2, 10, 0);
/* Show the various static text elements on the color STN display. */
GrContextFontSet(&g_sContext, TEXT_FONT);
GrContextForegroundSet(&g_sContext, ClrViolet);
GrStringDraw(&g_sContext, "CDC Serial 1 :-", -1, CDC1_STR_X_POSITION,
CDC1_STR_Y_POSITION, false);
GrStringDraw(&g_sContext, "CDC Serial 2 :-", -1, CDC2_STR_X_POSITION,
CDC1_STR_Y_POSITION, false);
GrContextForegroundSet(&g_sContext, ClrWhite);
GrStringDraw(&g_sContext, "Tx bytes:", -1, CDC1_STR_X_POSITION,
(CDC1_STR_Y_POSITION + CDC_STR_Y_DIFF), false);
GrStringDraw(&g_sContext, "Tx buffer:", -1, CDC1_STR_X_POSITION,
(CDC1_STR_Y_POSITION + (CDC_STR_Y_DIFF * 2)), false);
GrStringDraw(&g_sContext, "Rx bytes:", -1, CDC1_STR_X_POSITION,
(CDC1_STR_Y_POSITION + (CDC_STR_Y_DIFF * 4)), false);
GrStringDraw(&g_sContext, "Rx buffer:", -1, CDC1_STR_X_POSITION,
(CDC1_STR_Y_POSITION + (CDC_STR_Y_DIFF * 5)), false);
DrawBufferMeter(&g_sContext, CDC1_BUF_METER_X_POS, CDC1_BUF_METER_Y_POS);
DrawBufferMeter(&g_sContext, CDC1_BUF_METER_X_POS,
(CDC1_BUF_METER_Y_POS + CDC_BUF_METER_Y_DIFF));
GrStringDraw(&g_sContext, "Tx bytes:", -1, CDC2_STR_X_POSITION,
(CDC2_STR_Y_POSITION + CDC_STR_Y_DIFF), false);
GrStringDraw(&g_sContext, "Tx buffer:", -1, CDC2_STR_X_POSITION,
(CDC2_STR_Y_POSITION + (CDC_STR_Y_DIFF * 2)), false);
GrStringDraw(&g_sContext, "Rx bytes:", -1, CDC2_STR_X_POSITION,
(CDC2_STR_Y_POSITION + (CDC_STR_Y_DIFF * 4)), false);
GrStringDraw(&g_sContext, "Rx buffer:", -1, CDC2_STR_X_POSITION,
(CDC2_STR_Y_POSITION + (CDC_STR_Y_DIFF * 5)), false);
DrawBufferMeter(&g_sContext, CDC2_BUF_METER_X_POS, CDC2_BUF_METER_Y_POS);
DrawBufferMeter(&g_sContext, CDC2_BUF_METER_X_POS,
(CDC2_BUF_METER_Y_POS + CDC_BUF_METER_Y_DIFF));
DisplayStatus(&g_sContext, " Waiting for host... ");
/* Pass the USB library our device information, initialize the USB
controller and connect the device to the bus.
*/
g_psCompDevices[0].pvInstance =
USBDCDCCompositeInit(0, (tUSBDCDCDevice *)&g_sCDCDevice1);
g_psCompDevices[1].pvInstance =
USBDCDCCompositeInit(0, (tUSBDCDCDevice *)&g_sCDCDevice2);
/*
Pass the device information to the USB library and place the device
on the bus.
*/
USBDCompositeInit(0, &g_sCompDevice, DESCRIPTOR_DATA_SIZE,
g_pucDescriptorData);
/* Initialize the serial devices. */
SerialInit();
/* Drop into the main loop. */
while(1)
{
/* Allow the main serial routine to run. */
SerialMain();
}
}
/*
** Main function. The application starts here.
*/
int main(void)
{
unsigned char rxByte;
unsigned int value = (unsigned int)E_FAIL;
#ifdef __TMS470__
/* Relocate the required section to internal RAM */
memcpy((void *)(&relocstart), (const void *)(&iram_start),
(unsigned int)(&iram_size));
#elif defined(__IAR_SYSTEMS_ICC__)
#pragma section = "CodeRelocOverlay"
#pragma section = "DataRelocOverlay"
#pragma section = "DataOverlayBlk"
#pragma section = "CodeOverlayBlk"
char* srcAddr = (__section_begin("CodeRelocOverlay"));
char* endAddr = (__section_end("DataRelocOverlay"));
memcpy((void *)(__section_begin("CodeRelocOverlay")),
(const void *)(__section_begin("CodeOverlayBlk")),
endAddr - srcAddr);
#else
memcpy((void *)&(relocstart), (const void *)&(iram_start),
(unsigned int)(((&(relocend)) -
(&(relocstart))) * (sizeof(unsigned int))));
#endif
MMUConfigAndEnable();
/* Enable Instruction Cache */
CacheEnable(CACHE_ALL);
PeripheralsSetUp();
/* Initialize the ARM Interrupt Controller */
IntAINTCInit();
/* Register the ISRs */
Timer2IntRegister();
Timer4IntRegister();
EnetIntRegister();
RtcIntRegister();
CM3IntRegister();
HSMMCSDIntRegister();
IntRegister(127, dummyIsr);
IntMasterIRQEnable();
pageIndex = 0;
prevAction = 0;
/* Enable system interrupts */
IntSystemEnable(SYS_INT_RTCINT);
IntPrioritySet(SYS_INT_RTCINT, 0, AINTC_HOSTINT_ROUTE_IRQ);
IntSystemEnable(SYS_INT_3PGSWTXINT0);
IntPrioritySet(SYS_INT_3PGSWTXINT0, 0, AINTC_HOSTINT_ROUTE_IRQ);
IntSystemEnable(SYS_INT_3PGSWRXINT0);
IntPrioritySet(SYS_INT_3PGSWRXINT0, 0, AINTC_HOSTINT_ROUTE_IRQ);
IntSystemEnable(SYS_INT_TINT2);
IntPrioritySet(SYS_INT_TINT2, 0, AINTC_HOSTINT_ROUTE_IRQ);
IntSystemEnable(SYS_INT_TINT4);
IntPrioritySet(SYS_INT_TINT4, 0, AINTC_HOSTINT_ROUTE_IRQ);
IntSystemEnable(SYS_INT_MMCSD0INT);
IntPrioritySet(SYS_INT_MMCSD0INT, 0, AINTC_HOSTINT_ROUTE_IRQ);
IntSystemEnable(SYS_INT_EDMACOMPINT);
IntPrioritySet(SYS_INT_EDMACOMPINT, 0, AINTC_HOSTINT_ROUTE_IRQ);
IntPrioritySet(SYS_INT_M3_TXEV, 0, AINTC_HOSTINT_ROUTE_IRQ );
IntSystemEnable(SYS_INT_M3_TXEV);
IntSystemEnable(127);
IntPrioritySet(127, 0, AINTC_HOSTINT_ROUTE_IRQ);
IntSystemEnable(SYS_INT_UART0INT);
IntPrioritySet(SYS_INT_UART0INT, 0, AINTC_HOSTINT_ROUTE_IRQ);
IntRegister(SYS_INT_UART0INT, uartIsr);
/* GPIO interrupts */
IntSystemEnable(SYS_INT_GPIOINT0A);
IntPrioritySet(SYS_INT_GPIOINT0A, 0, AINTC_HOSTINT_ROUTE_IRQ);
IntRegister(SYS_INT_GPIOINT0A, gpioIsr);
IntSystemEnable(SYS_INT_GPIOINT0B);
IntPrioritySet(SYS_INT_GPIOINT0B, 0, AINTC_HOSTINT_ROUTE_IRQ);
IntRegister(SYS_INT_GPIOINT0B, gpioIsr);
BoardInfoInit();
deviceVersion = DeviceVersionGet();
CM3EventsClear();
CM3LoadAndRun();
waitForM3Txevent();
/* Initialize console for communication with the Host Machine */
ConsoleUtilsInit();
/*
** Select the console type based on compile time check
** Note: This example is not fully complaint to semihosting. It is
** recommended to use Uart console interface only.
*/
ConsoleUtilsSetType(CONSOLE_UART);
/* Print Board and SoC information on console */
ConsoleUtilsPrintf("\n\r Board Name : %s", BoardNameGet());
ConsoleUtilsPrintf("\n\r Board Version : %s", BoardVersionGet());
ConsoleUtilsPrintf("\n\r SoC Version : %d", deviceVersion);
/* On CM3 init firmware version is loaded onto the IPC Message Reg */
ConsoleUtilsPrintf("\n CM3 Firmware Version: %d", readCM3FWVersion());
I2CIntRegister(I2C_0);
IntPrioritySet(SYS_INT_I2C0INT, 0, AINTC_HOSTINT_ROUTE_IRQ);
IntSystemEnable(SYS_INT_I2C0INT);
I2CInit(I2C_0);
IntSystemEnable(SYS_INT_TINT1_1MS);
IntPrioritySet(SYS_INT_TINT1_1MS, 0, AINTC_HOSTINT_ROUTE_IRQ);
IntRegister(SYS_INT_TINT1_1MS,clearTimerInt);
configVddOpVoltage();
RtcInit();
HSMMCSDContolInit();
DelayTimerSetup();
initializeTimer1();
ConsoleUtilsPrintf("\r\n After intializing timer");
Timer2Config();
Timer4Config();
LedIfConfig();
MailBoxInit();
Timer2IntEnable();
Timer4IntEnable();
RtcSecIntEnable();
Timer4Start();
while(FALSE == tmr4Flag);
tmr4Flag = FALSE;
Timer4Stop();
ConsoleUtilsPrintf("\n\r Configuring for maximum OPP");
mpuOpp = ConfigMaximumOPP();
mpuFreq = FrequencyGet(mpuOpp);
mpuVdd1 = VddVoltageGet(mpuOpp);
PrintConfigDVFS();
/* Create menu page */
pageIndex = MENU_IDX_MAIN;
ActionEnetInit();
/*
** Loop for ever. Necessary actions shall be taken
** after detecting the click.
*/
while(1)
{
/*
** Check for any any activity on Uart Console and process it.
*/
if (true == UARTCharsAvail(SOC_UART_0_REGS))
{
/* Receiving bytes from the host machine through serial console. */
rxByte = UARTGetc();
/*
** Checking if the entered character is a carriage return.
** Pressing the 'Enter' key on the keyboard executes a
** carriage return on the serial console.
*/
if('\r' == rxByte)
{
ConsoleUtilsPrintf("\n");
UartAction(value);
value = (unsigned int)E_FAIL;
rxByte = 0;
}
/*
** Checking if the character entered is one among the decimal
** number set 0,1,2,3,....9
*/
if(('0' <= rxByte) && (rxByte <= '9'))
{
ConsoleUtilsPrintf("%c", rxByte);
if((unsigned int)E_FAIL == value)
{
value = 0;
}
value = value*10 + (rxByte - 0x30);
}
}
/*
** Check if click is detected
*/
if(clickIdx != 0)
{
/*
** Take the Action for click
*/
ClickAction();
clickIdx = 0;
}
/*
** Check if the Timer Expired
*/
if(TRUE == tmrFlag)
{
/* Toggle the LED state */
LedToggle();
tmrFlag = FALSE;
}
/*
** Check if RTC Time is set
*/
if(TRUE == rtcSetFlag)
{
if(TRUE == rtcSecUpdate)
{
rtcSecUpdate = FALSE;
RtcTimeCalDisplay();
ConsoleUtilsPrintf(" --- Selected: ");
}
}
if(TRUE == tmr4Flag)
{
tmr4Flag = FALSE;
/* Make sure that interrupts are disabled and no lwIP functions
are executed while calling an lwIP exported API */
IntMasterIRQDisable();
etharp_tmr();
IntMasterIRQEnable();
}
}
}
//*****************************************************************************
//
// This is the main application entry function.
//
//*****************************************************************************
int
main(void)
{
unsigned int ulTxCount;
unsigned int ulRxCount;
tRectangle sRect;
char pcBuffer[16];
unsigned int i;
unsigned char *src, *dest;
MMUConfigAndEnable();
//
// USB module clock enable
//
USB0ModuleClkConfig();
//
//USB interrupt enable
//
USBInterruptEnable();
//
//LCD back light enable
//
LCDBackLightEnable();
// UPD Pin setup
//
//
UPDNPinControl();
//
//Delay timer setup
//
DelayTimerSetup();
//
//Configures raster to display image
//
SetUpLCD();
RasterDMAFBConfig(SOC_LCDC_0_REGS,
(unsigned int)(g_pucBuffer+PALETTE_OFFSET),
(unsigned int)(g_pucBuffer+PALETTE_OFFSET) + sizeof(g_pucBuffer) - 2 -
PALETTE_OFFSET, FRAME_BUFFER_0);
RasterDMAFBConfig(SOC_LCDC_0_REGS,
(unsigned int)(g_pucBuffer+PALETTE_OFFSET),
(unsigned int)(g_pucBuffer+PALETTE_OFFSET) + sizeof(g_pucBuffer) - 2 -
PALETTE_OFFSET, FRAME_BUFFER_1);
src = (unsigned char *) palette_32b;
dest = (unsigned char *) (g_pucBuffer+PALETTE_OFFSET);
// Copy palette info into buffer
for( i = PALETTE_OFFSET; i < (PALETTE_SIZE+PALETTE_OFFSET); i++)
{
*dest++ = *src++;
}
GrOffScreen24BPPInit(&g_s35_800x480x24Display, g_pucBuffer, LCD_WIDTH, LCD_HEIGHT);
// Initialize a drawing context.
GrContextInit(&g_sContext, &g_s35_800x480x24Display);
/* enable End of frame interrupt */
RasterEndOfFrameIntEnable(SOC_LCDC_0_REGS);
/* enable raster */
RasterEnable(SOC_LCDC_0_REGS);
//
// Fill the top 15 rows of the screen with blue to create the banner.
//
sRect.sXMin = 0;
sRect.sYMin = 0;
sRect.sXMax = GrContextDpyWidthGet(&g_sContext) - 1;
sRect.sYMax = 23;
GrContextForegroundSet(&g_sContext, ClrDarkBlue);
GrRectFill(&g_sContext, &sRect);
//
// Put a white box around the banner.
//
GrContextForegroundSet(&g_sContext, ClrWhite);
GrRectDraw(&g_sContext, &sRect);
//
// Put the application name in the middle of the banner.
//
GrContextFontSet(&g_sContext, &g_sFontCm20);
GrStringDrawCentered(&g_sContext, "usb-dev-bulk", -1,
GrContextDpyWidthGet(&g_sContext) / 2, 10, 0);
//
// Show the various static text elements on the color STN display.
//
GrContextFontSet(&g_sContext, TEXT_FONT);
GrStringDraw(&g_sContext, "Tx bytes:", -1, 8, 100, false);
GrStringDraw(&g_sContext, "Rx bytes:", -1, 8, 130, false);
//
// Tell the user what we are up to.
//
DisplayStatus(&g_sContext, " Configuring USB... ");
//
// Initialize the transmit and receive buffers.
//
USBBufferInit((tUSBBuffer *)&g_sTxBuffer);
USBBufferInit((tUSBBuffer *)&g_sRxBuffer);
//
// Pass our device information to the USB library and place the device
// on the bus.
//
USBDBulkInit(0, (tUSBDBulkDevice *)&g_sBulkDevice);
//
// Wait for initial configuration to complete.
//
DisplayStatus(&g_sContext, "Waiting for host...");
//
// Clear our local byte counters.
//
ulRxCount = 0;
ulTxCount = 0;
//
// Main application loop.
//
while(1)
{
//
// Have we been asked to update the status display?
//
if(g_ulFlags & COMMAND_STATUS_UPDATE)
{
//
// Clear the command flag
//
g_ulFlags &= ~COMMAND_STATUS_UPDATE;
DisplayStatus(&g_sContext, g_pcStatus);
}
//
// Has there been any transmit traffic since we last checked?
//
if(ulTxCount != g_ulTxCount)
{
//
// Take a snapshot of the latest transmit count.
//
ulTxCount = g_ulTxCount;
//
// Update the display of bytes transmitted by the UART.
//
usnprintf(pcBuffer, 16, " %d ", ulTxCount);
GrStringDraw(&g_sContext, pcBuffer, -1, 120, 100, true);
}
//
// Has there been any receive traffic since we last checked?
//
if(ulRxCount != g_ulRxCount)
{
//
// Take a snapshot of the latest receive count.
//
ulRxCount = g_ulRxCount;
//
// Update the display of bytes received by the UART.
//
usnprintf(pcBuffer, 16, " %d ", ulRxCount);
GrStringDraw(&g_sContext, pcBuffer, -1, 120, 130, true);
}
}
}
int main(void)
{
volatile unsigned int i = 0;
volatile unsigned int initFlg = 1;
#ifdef ARM_SUPPORTED
/* Setup the MMU and do necessary MMU configurations. */
MMUConfigAndEnable();
#endif
#ifdef CACHE_SUPPORTED
/* Enable all levels of CACHE. */
CacheEnable(CACHE_ALL);
#endif
/* Initialize UART. */
UARTStdioInit();
/* Configure the EDMA clocks. */
EDMAModuleClkConfig();
/* Configure EDMA to service the MMCSD events. */
MMCSDEdmaInit();
/* Perform pin-mux for MMCSD pins. */
MMCSDPinMuxSetup();
/* Enable module clock for MMCSD. */
MMCSDModuleClkConfig();
DelayTimerSetup();
#ifdef MMCSD_PERF
PerfTimerSetup();
#endif
/* Basic controller initializations */
MMCSDControllerSetup();
/* Initialize the MMCSD controller */
MMCSDCtrlInit(&ctrlInfo);
MMCSDIntEnable(&ctrlInfo);
#if 0
UARTPuts("Test timer:wait 5s\r\n", -1);
delay(5000);
UARTPuts("Test timer:Done\r\n", -1);
#endif
for(;;)
{
if((MMCSDCardPresent(&ctrlInfo)) == 1)
{
#if DEBUG_PRINT
UARTPuts("Card is present\r\n", -1);
#endif
if(initFlg)
{
UARTPuts("Call MMCSDFsMount\r\n", -1);
MMCSDFsMount(0, &sdCard);
UARTPuts("Back MMCSDFsMount\r\n", -1);
initFlg = 0;
UARTPuts("Call Cmd_help\r\n", -1);
Cmd_help(0, NULL);
}
MMCSDFsProcessCmdLine();
}
else
{
UARTPuts("Card is not present\r\n", -1);
delay(1000);
// delay(1);
i = (i + 1) & 0xFFF;
if(i == 1)
{
UARTPuts("Please insert the card \r\n", -1);
}
if(initFlg != 1)
{
/* Reinitialize all the state variables */
dmaIsRunning = 0;
xferCompFlag = 0;
dataTimeout = 0;
dataCRCError = 0;
cmdCompFlag = 0;
cmdTimeout = 0;
/* Initialize the MMCSD controller */
MMCSDCtrlInit(&ctrlInfo);
MMCSDIntEnable(&ctrlInfo);
}
initFlg = 1;
}
}
}
