void PB_Init (void)
{
PB_Config(); /* Configure the port pins */
PB_IntInit(); /* Configure interrupt settings */
}
int main(void){
//configure push-button interrupts
PB_Config();
/* LCD initiatization */
LCD_Init();
/* LCD Layer initiatization */
LCD_LayerInit();
/* Enable the LTDC */
LTDC_Cmd(ENABLE);
/* Set LCD foreground layer */
LCD_SetLayer(LCD_FOREGROUND_LAYER);
//======You need to develop the following functions======
//Note: these are just placeholders; function definitions are at bottom of this file
//configure real-time clock
RTC_Config();
//configure external push-buttons and interrupts
ExtPB_Config();
ExtPBNum2();
//main program
LCD_Clear(LCD_COLOR_WHITE);
//line=0;
//Display a string in one line, on the first line (line=0)
//LCD_DisplayStringLine(LINE(line), (uint8_t *) "Init EEPROM...");
//line++;
//i2c_init(); //initialize the i2c chip
sEE_Init();
//LCD_DisplayStringLine(LINE(line), (uint8_t *) "done...");
//line++;
//LCD_DisplayStringLine(LINE(line), (uint8_t *) "Writing...");
//line++;
/* First write in the memory followed by a read of the written data --------*/
/* Write on I2C EEPROM from memLocation */
//sEE_WriteBuffer(&Tx1_Buffer, memLocation,1);
/* Wait for EEPROM standby state */
//sEE_WaitEepromStandbyState();
//LCD_DisplayStringLine(LINE(line), (uint8_t *) "Reading...");
/* Read from I2C EEPROM from memLocation */
//sEE_ReadBuffer(&Rx1_Buffer, memLocation, (uint16_t *)(&NumDataRead));
//line++;
//LCD_DisplayStringLine(LINE(line), (uint8_t *) "Comparing...");
//line++;
//if(Tx1_Buffer== Rx1_Buffer){
//LCD_DisplayStringLine(LINE(line), (uint8_t *) "Success!");
//}else{
//LCD_DisplayStringLine(LINE(line), (uint8_t *) "Mismatch!");
//}
//main loop
while(1){
RTC_GetTime(RTC_Format_BIN,&RTC_TimeStructure);
hours = RTC_TimeStructure.RTC_Hours;
minutes = RTC_TimeStructure.RTC_Minutes;
seconds = RTC_TimeStructure.RTC_Seconds;
sprintf(time,"%0.2d:%0.2d:%0.2d",hours,minutes,seconds);
LCD_DisplayStringLine(LINE(6), (uint8_t *) time);
if(UBPressed == 1){
toBeSaved = time[7];
sEE_WriteBuffer(&toBeSaved, memLocation+1,1);
sEE_WaitEepromStandbyState();
sEE_ReadBuffer(&Rx1_Buffer, memLocation+1, (uint16_t *)(&NumDataRead));
saved[0] = Rx1_Buffer;
LCD_DisplayStringLine(LINE(7), (uint8_t *) saved);
UBPressed = 0;
PB_Config();
}
if(EB1Pressed == 1 && state == 0){
state = 1;
EB1Pressed = 0;
ExtPB_Config();
}
if(EB1Pressed == 1 && state == 1){
state = 2;
EB1Pressed = 0;
ExtPB_Config();
}
if(EB1Pressed == 1 && state == 2){
state = 3;
EB1Pressed = 0;
ExtPB_Config();
}
if(EB1Pressed == 1 && state == 3){
state = 0;
EB1Pressed = 0;
ExtPB_Config();
}
if(EB2Pressed == 1 && state == 1){
RTC_TimeStructure.RTC_Hours = hours + 1;
RTC_SetTime(RTC_Format_BCD, &RTC_TimeStructure);
EB2Pressed = 0;
ExtPBNum2();
}
if(EB2Pressed == 1 && state == 2){
RTC_TimeStructure.RTC_Minutes = minutes + 1;
RTC_SetTime(RTC_Format_BCD, &RTC_TimeStructure);
EB2Pressed = 0;
ExtPBNum2();
}
if(EB2Pressed == 1 && state == 3){
RTC_TimeStructure.RTC_Seconds = seconds + 1;
RTC_SetTime(RTC_Format_BCD, &RTC_TimeStructure);
EB2Pressed = 0;
ExtPBNum2();
}
}
}
int main(void)
{
/*!< At this stage the microcontroller clock setting is already configured,
this is done through SystemInit() function which is called from startup
file (startup_stm32f4xx.s) before to branch to application main.
To reconfigure the default setting of SystemInit() function, refer to
system_stm32f4xx.c file
*/
//initiate user button
PB_Config();
//initiate LEDs and turn them on
LED_Config();
/* -----------------------------------------------------------------------
TIM3 Configuration: Output Compare Timing Mode:
In this example TIM3 input clock (TIM3CLK) is set to 2 * APB1 clock (PCLK1),
since APB1 prescaler is different from 1.
TIM3CLK = 2 * PCLK1
PCLK1 = HCLK / 4
=> TIM3CLK = HCLK / 2 = SystemCoreClock /2
To get TIM3 counter clock at 50 MHz, the prescaler is computed as follows:
Prescaler = (TIM3CLK / TIM3 counter clock) - 1
Prescaler = ((SystemCoreClock /2) /0.5 MHz) - 1
CC1 update rate = TIM3 counter clock / CCR1_Val = 10.0 Hz
==> Toggling frequency = 5 Hz
Note:
SystemCoreClock variable holds HCLK frequency and is defined in system_stm32f4xx.c file.
Each time the core clock (HCLK) changes, user had to call SystemCoreClockUpdate()
function to update SystemCoreClock variable value. Otherwise, any configuration
based on this variable will be incorrect.
----------------------------------------------------------------------- */
//=======================Configure and init Timer======================
/* Compute the prescaler value */
PrescalerValue = (uint16_t) ((SystemCoreClock / 2) / 500000) - 1;
/* TIM Configuration */
TIM3_Config();
// configure the output compare
TIM3_OCConfig();
/* TIM Interrupts enable */
TIM_ITConfig(TIM3, TIM_IT_CC1, ENABLE);
/* TIM3 enable counter */
TIM_Cmd(TIM3, ENABLE);
//======================================configure and init LCD ======================
/* LCD initiatization */
LCD_Init();
/* LCD Layer initiatization */
LCD_LayerInit();
/* Enable the LTDC */
LTDC_Cmd(ENABLE);
/* Set LCD foreground layer */
LCD_SetLayer(LCD_FOREGROUND_LAYER);
//================EEPROM init====================================
/* Unlock the Flash Program Erase controller */
FLASH_Unlock();
/* EEPROM Init */
EE_Init();
//============ Set up for random number generation==============
RNG_Config();
//with the default font, LCD can display 12 lines of chars, they are LINE(0), LINE(1)...LINE(11)
//with the default font, LCD can display 15 columns, they are COLUMN(0)....COLUMN(14)
LCD_Clear(LCD_COLOR_WHITE);
LCD_DisplayStringLine(LINE(0), (uint8_t *) "Attempt");
LCD_DisplayStringLine(LINE(2), (uint8_t *) "Record");
EE_WriteVariable(VirtAddVarTab[0],VarValue);
EE_ReadVariable(VirtAddVarTab[0], &VarDataTab[0]);
sprintf(str, "%d", VarDataTab[0]);
//LCD_DisplayStringLine(LINE(3), (uint8_t *) str);
//randomNumber = RNG_GetRandomNumber()/100000;
//sprintf(str, "%d", randomNumber());
//LCD_DisplayStringLine(LINE(5), (uint8_t *) str);
resetTimer();
/*the following while loop is where the main part of the code is
* it currently uses the userbutton on board since Mario forgot to bring along his
* jumper cables to test out the push button part
*/
//if toggle = 0 lights are blinking
//if toggle = 1 2 second wait
//if toggle = 2 LED toggle off, the lights stay on
//@TODO add external push button to code
externalButton();
while (1){
int num = TIM_GetCounter(TIM3);
//This is for the start of the procedure
if(toggle==0){
if(num == 3000){
STM_EVAL_LEDOn(LED3);
STM_EVAL_LEDOn(LED4);
}
else if(num == 6000){
STM_EVAL_LEDOff(LED3);
STM_EVAL_LEDOff(LED4);
resetTimer();
}
}
//if the user button has been pressed and the lights are blinking
if (UBPressed==1 && toggle==0) {
STM_EVAL_LEDOff(LED3);
STM_EVAL_LEDOff(LED4);
UBPressed=0;
PB_Config();
resetTimerLong();
toggle = 1;
rand = randomNumber();//generate a random number
}
//this is the to get the wait time for the reaction test.
if(toggle==1){
if(num == rand){ //if num is equal to the ramdom gened number turn on the LEDs and reset the timer
STM_EVAL_LEDOn(LED3);
STM_EVAL_LEDOn(LED4);
resetTimerLong();
}
}
//this is the code for when the reaction timer has gone off
if (UBPressed==1 && toggle==1) {
//this if statement is to prevent cheating
//if the number = 0 it means that the user cheated as someone should not be able to get 0
if(num == 0){
ExtButtonPressed=0;
PB_Config();
externalButton();
resetTimer();
toggle = 0;
}else{
sprintf(str, "%d", num);
//this block of code writes to the LCD the lastest user reaction time.
LCD_DisplayStringLine(LINE(1), (uint8_t *) " ");
LCD_DisplayStringLine(LINE(1), (uint8_t *) str);
EE_ReadVariable(VirtAddVarTab[0], &VarDataTab[0]);
//this if statement determines wheter the user has beat their best reaction time
if(num < VarDataTab[0]){
VarValue = num;
EE_WriteVariable(VirtAddVarTab[0],VarValue);
}
/*the following block of code writes to the LCD the record reaction time*/
EE_ReadVariable(VirtAddVarTab[0], &VarDataTab[0]);
sprintf(str, "%d", VarDataTab[0]);
LCD_DisplayStringLine(LINE(3), (uint8_t *) " ");
LCD_DisplayStringLine(LINE(3), (uint8_t *) str);
UBPressed=0;
PB_Config();
resetTimerLong();
toggle = 2;
}
}
//the user needs to press the button to get the reaction time game going again.
//to reset the reaction timer
if (ExtButtonPressed==1) {
ExtButtonPressed=0;
PB_Config();
externalButton();
resetTimer();
toggle = 0;
}
}
}
int main(void)
{
/*!< At this stage the microcontroller clock setting is already configured,
this is done through SystemInit() function which is called from startup
file (startup_stm32f4xx.s) before to branch to application main.
To reconfigure the default setting of SystemInit() function, refer to
system_stm32f4xx.c file
*/
//initiate user button
PB_Config();
//initiate LEDs and turn them on
LED_Config();
/* -----------------------------------------------------------------------
TIM3 Configuration: Output Compare Timing Mode:
In this example TIM3 input clock (TIM3CLK) is set to 2 * APB1 clock (PCLK1),
since APB1 prescaler is different from 1.
TIM3CLK = 2 * PCLK1
PCLK1 = HCLK / 4
=> TIM3CLK = HCLK / 2 = SystemCoreClock /2
To get TIM3 counter clock at 50 MHz, the prescaler is computed as follows:
Prescaler = (TIM3CLK / TIM3 counter clock) - 1
Prescaler = ((SystemCoreClock /2) /50 MHz) - 1
CC1 update rate = TIM3 counter clock / CCR1_Val = 9.154 Hz
==> Toggling frequency = 4.57 Hz
Note:
SystemCoreClock variable holds HCLK frequency and is defined in system_stm32f4xx.c file.
Each time the core clock (HCLK) changes, user had to call SystemCoreClockUpdate()
function to update SystemCoreClock variable value. Otherwise, any configuration
based on this variable will be incorrect.
----------------------------------------------------------------------- */
//=======================Configure and init Timer======================
/* Compute the prescaler value */
PrescalerValue = (uint16_t) ((SystemCoreClock / 2) / 200000) - 1;
/* TIM Configuration */
TIM2_Config();
// configure the output compare
TIM2_OCConfig();
/* TIM Interrupts enable */
TIM_ITConfig(TIM2, TIM_IT_CC1, ENABLE);
/* TIM3 enable counter */
TIM_Cmd(TIM2, ENABLE);
while (1){
if (UBPressed==1) {
STM_EVAL_LEDOff(LED3);
STM_EVAL_LEDOff(LED4);
hardwareBlinking();
UBPressed=0;
}
}
}
