/******************************************************************************
* Function: void UserInit(void)
*
* PreCondition: None
*
* Input: None
*
* Output: None
*
* Side Effects: None
*
* Overview: This routine should take care of all of the demo code
* initialization that is required.
*
* Note:
*
*****************************************************************************/
void UserInit(void)
{
// Real time clock start
RtccInitClock();
RtccWrOn();
{
rtccTimeDate initd;
initd.f.year=0x10;
initd.f.mon=0x01;
initd.f.mday=0x01;
initd.f.wday=5; // 2010.01.01 is friday
initd.f.hour=0;
initd.f.min=0;
initd.f.sec=0;
RtccWriteTimeDate(&initd,FALSE);
RtccWriteAlrmTimeDate(&initd);
}
mRtccOn();
mRtccAlrmEnable();
RtccSetAlarmRpt(RTCC_RPT_MIN,TRUE);
// Mtouch init
mTouchInit();
mTouchCalibrate();
cmdstr[0]=0;
screen=0;
screenvalid=0;
position=0;
buttonstate.Val=0;
buttonpressed.Val=0;
devicereset=0;
clockss=0;
resetcounter=0;
alarmcnt=0;
TRISBbits.TRISB1=0;
PPSUnLock();
iPPSOutput(OUT_PIN_PPS_RP4,OUT_FN_PPS_CCP1P1A); //Configre RP24 as C1OUT pin
PPSLock();
//----Configure pwm ----
period = 0xFF;
OpenPWM1( period); //Configure PWM module and initialize PWM period
//-----set duty cycle----
duty_cycle = 256;
SetDCPWM1(duty_cycle); //set the duty cycle
//----set pwm output----
outputconfig = HALF_OUT ;
outputmode = PWM_MODE_1;
SetOutputPWM1( outputconfig, outputmode); //output PWM in respective modes
ADCON0bits.CHS=4;
/* Make sure A/D interrupt is not set */
PIR1bits.ADIF = 0;
/* Begin A/D conversion */
}//end UserInit
void remapAllPins() {
PPSUnLock();
/* pins used by mimac to comunicate radio */
iPPSInput(IN_FN_PPS_INT1, IN_PIN_PPS_RP17);
/* pins used by usart loging */
iPPSOutput(OUT_PIN_PPS_RP21, OUT_FN_PPS_TX2CK2); // Mapping USART2 TX
iPPSInput(IN_FN_PPS_RX2DT2, IN_PIN_PPS_RP22); // Mapping USART2 RX
iPPSInput(IN_FN_PPS_INT2, IN_PIN_PPS_RP4);
iPPSOutput(OUT_PIN_PPS_RP23, OUT_FN_PPS_CCP1P1A); // LEDs mapped to PWM
iPPSOutput(OUT_PIN_PPS_RP24, OUT_FN_PPS_P1B);
// Lock System
PPSLock();
}
int main(void)
#endif
{
BYTE i, j;
BYTE TxSynCount = 0;
BOOL bReceivedMessage = FALSE;
_U16 m;
#define BAUDRG 77
/*******************************************************************/
// Initialize the system
/*******************************************************************/
ANCON0 = 0XFF; /*desactiva entradas analogicas*/
ANCON1 = 0XFF; /*desactiva entradas analogicas*/
PPSUnLock();
PPSOutput(PPS_RP10, PPS_TX2CK2); // TX2 RP17/RC6
PPSInput(PPS_RX2DT2, PPS_RP9); // RX2 RP18/RC7
PPSOutput(PPS_RP23, PPS_SDO2); // SDO2 RP23/RD6
PPSInput(PPS_SDI2, PPS_RP24); // SDI2 RP24/RD7
PPSOutput(PPS_RP22, PPS_SCK2); // SCK2 RP22/RD5
PPSLock();
System_PeripheralPinSelect( ExternalInterrupt3, 19); /*external interrupt 3 B3*/
BoardInit();
ConsoleInit();
Open2USART(USART_TX_INT_OFF & USART_RX_INT_OFF & USART_EIGHT_BIT & USART_ASYNCH_MODE & USART_ADDEN_OFF, BAUDRG);
baud2USART(BAUD_IDLE_TX_PIN_STATE_HIGH & BAUD_IDLE_RX_PIN_STATE_HIGH & BAUD_AUTO_OFF & BAUD_WAKEUP_OFF & BAUD_16_BIT_RATE & USART_RX_INT_OFF);
Gpios_PinDirection(GPIOS_PORTD, 7, GPIOS_INPUT); /*pin C0 como salida para SDI*/
Gpios_PinDirection(GPIOS_PORTD, 6, GPIOS_OUTPUT); /*pin C1 como salida para SDO*/
Gpios_PinDirection(GPIOS_PORTD, 5, GPIOS_OUTPUT); /*pin C2 como salida para SCK*/
Spi_Init(SPI_PORT1, SPI_64DIV); /*Inicializamos SPI2*/
Spi_Init(SPI_PORT2, SPI_64DIV); /*Inicializamos SPI2*/
//Spi_SetMode(SPI_PORT1, 1);
//Spi_SetMode(SPI_PORT1, 1);
LED_1 = 1;
LED_2 = 1;
Read_MAC_Address();
LED_1 = 0;
LED_2 = 0;
ConsolePutROMString((ROM char *)"\r\n<MAC Addr:");
PrintChar(myLongAddress[3]);
PrintChar(myLongAddress[2]);
PrintChar(myLongAddress[1]);
PrintChar(myLongAddress[0]);
ConsolePutROMString((ROM char *)"\r>");
Printf("\r\nStarting Testing Interface for MiWi(TM) PRO Stack ...");
#if defined(MRF24J40)
Printf("\r\n RF Transceiver: MRF24J40");
#elif defined(MRF49XA)
Printf("\r\n RF Transceiver: MRF49XA");
#elif defined(MRF89XA)
Printf("\r\n RF Transceiver: MRF89XA");
#endif
Printf("\r\n Demo Instruction:");
Printf("\r\n Press Enter to bring up the menu.");
Printf("\r\n Type in hyper terminal to choose");
Printf("\r\n menu item. ");
Printf("\r\n\r\n");
/*******************************************************************/
// Following block display demo information on LCD of Explore 16 or
// PIC18 Explorer demo board.
/*******************************************************************/
#if defined(MRF49XA)
LCDDisplay((char *)"MiWi PRO Test Interface MRF49XA", 0, TRUE);
#elif defined(MRF24J40)
LCDDisplay((char *)"MiWi PRO Test Interface MRF24J40", 0, TRUE);
#elif defined(MRF89XA)
LCDDisplay((char *)"MiWi PRO Test Interface MRF89XA", 0, TRUE);
#endif
//if( (PUSH_BUTTON_1 == 0) || ( MiApp_ProtocolInit(TRUE) == FALSE ) )
if (PUSH_BUTTON_1 == 1)
{
MiApp_ProtocolInit(FALSE);
LED_1 = 0;
LED_2 = 0;
#ifdef ENABLE_ACTIVE_SCAN
myChannel = 0xFF;
ConsolePutROMString((ROM char *)"\r\nStarting Active Scan...");
LCDDisplay((char *)"Active Scanning", 0, FALSE);
/*******************************************************************/
// Function MiApp_SearchConnection will return the number of
// existing connections in all channels. It will help to decide
// which channel to operate on and which connection to add.
// The return value is the number of connections. The connection
// data are stored in global variable ActiveScanResults.
// Maximum active scan result is defined as
// ACTIVE_SCAN_RESULT_SIZE
// The first parameter is the scan duration, which has the same
// definition in Energy Scan. 10 is roughly 1 second. 9 is a
// half second and 11 is 2 seconds. Maximum scan duration is 14,
// or roughly 16 seconds.
// The second parameter is the channel map. Bit 0 of the
// double word parameter represents channel 0. For the 2.4GHz
// frequency band, all possible channels are channel 11 to
// channel 26. As the result, the bit map is 0x07FFF800. Stack
// will filter out all invalid channels, so the application
// only needs to pay attention to the channels that are not
// preferred.
/*******************************************************************/
i = MiApp_SearchConnection(10, 0x02000000);
if( i > 0 )
{
// now print out the scan result.
Printf("\r\nActive Scan Results: \r\n");
for(j = 0; j < i; j++)
{
Printf("Channel: ");
PrintDec(ActiveScanResults[j].Channel );
Printf(" RSSI: ");
PrintChar(ActiveScanResults[j].RSSIValue);
Printf("\r\n");
myChannel = ActiveScanResults[j].Channel;
Printf("PeerInfo: ");
PrintChar( ActiveScanResults[j].PeerInfo[0]);
}
}
#endif
/*******************************************************************/
// Function MiApp_ConnectionMode sets the connection mode for the
// protocol stack. Possible connection modes are:
// - ENABLE_ALL_CONN accept all connection request
// - ENABLE_PREV_CONN accept only known device to connect
// - ENABL_ACTIVE_SCAN_RSP do not accept connection request, but
// allow response to active scan
// - DISABLE_ALL_CONN disable all connection request, including
// active scan request
/*******************************************************************/
MiApp_ConnectionMode(ENABLE_ALL_CONN);
if( i > 0 )
{
/*******************************************************************/
// Function MiApp_EstablishConnection try to establish a new
// connection with peer device.
// The first parameter is the index to the active scan result, which
// is acquired by discovery process (active scan). If the value
// of the index is 0xFF, try to establish a connection with any
// peer.
// The second parameter is the mode to establish connection, either
// direct or indirect. Direct mode means connection within the
// radio range; Indirect mode means connection may or may not
// in the radio range.
/*******************************************************************/
if( MiApp_EstablishConnection(0, CONN_MODE_DIRECT) == 0xFF )
{
Printf("\r\nJoin Fail");
}
}
else
{
/*******************************************************************/
// Function MiApp_StartConnection tries to start a new network
//
// The first parameter is the mode of start connection. There are
// two valid connection modes:
// - START_CONN_DIRECT start the connection on current
// channel
// - START_CONN_ENERGY_SCN perform an energy scan first,
// before starting the connection on
// the channel with least noise
// - START_CONN_CS_SCN perform a carrier sense scan
// first, before starting the
// connection on the channel with
// least carrier sense noise. Not
// supported on currrent radios
//
// The second parameter is the scan duration, which has the same
// definition in Energy Scan. 10 is roughly 1 second. 9 is a
// half second and 11 is 2 seconds. Maximum scan duration is
// 14, or roughly 16 seconds.
//
// The third parameter is the channel map. Bit 0 of the
// double word parameter represents channel 0. For the 2.4GHz
// frequency band, all possible channels are channel 11 to
// channel 26. As the result, the bit map is 0x07FFF800. Stack
// will filter out all invalid channels, so the application
// only needs to pay attention to the channels that are not
// preferred.
/*******************************************************************/
#ifdef ENABLE_ED_SCAN
//LCDDisplay((char *)"Active Scanning Energy Scanning", 0, FALSE);
ConsolePutROMString((ROM char *)"\r\nActive Scanning Energy Scanning");
MiApp_StartConnection(START_CONN_ENERGY_SCN, 10, 0x02000000);
#endif
}
// Turn on LED 1 to indicate ready to accept new connections
LED_1 = 1;
}
else
{
//LCDDisplay((char *)" Network Freezer ENABLED", 0, TRUE);
Printf("\r\nNetwork Freezer Feature is enabled. There will be no hand-shake process.\r\n");
LED_1 = 1;
DumpConnection(0xFF);
}
LCDDisplay((char *)"Start Connection on Channel %d", currentChannel, TRUE);
LCDDisplay((char *)"Testing Menu on Hyper Terminal", 0, FALSE);
while(1)
{
/*******************************************************************/
// Function MiApp_MessageAvailable will return a boolean to indicate
// if a message for application layer has been received by the
// transceiver. If a message has been received, all information will
// be stored in the rxMessage, structure of RECEIVED_MESSAGE.
/*******************************************************************/
if( MiApp_MessageAvailable() )
{
/*******************************************************************/
// If a packet has been received, following code prints out some of
// the information available in rxFrame.
/*******************************************************************/
if( rxMessage.flags.bits.secEn )
{
ConsolePutROMString((ROM char *)"Secured ");
}
if( rxMessage.flags.bits.broadcast )
{
ConsolePutROMString((ROM char *)"Broadcast Packet with RSSI ");
}
else
{
ConsolePutROMString((ROM char *)"Unicast Packet with RSSI ");
}
PrintChar(rxMessage.PacketRSSI);
if( rxMessage.flags.bits.srcPrsnt )
{
ConsolePutROMString((ROM char *)" from ");
if( rxMessage.flags.bits.altSrcAddr )
{
PrintChar(rxMessage.SourceAddress[1]);
PrintChar(rxMessage.SourceAddress[0]);
}
else
{
for(i = 0; i < MY_ADDRESS_LENGTH; i++)
{
PrintChar(rxMessage.SourceAddress[MY_ADDRESS_LENGTH-1-i]);
}
}
}
ConsolePutROMString((ROM char *)": ");
for(i = 0; i < rxMessage.PayloadSize; i++)
{
ConsolePut(rxMessage.Payload[i]);
}
// Toggle LED2 to indicate receiving a packet.
LED_2 ^= 1;
/*******************************************************************/
// Function MiApp_DiscardMessage is used to release the current
// received message. After calling this function, the stack can
// start to process the next received message.
/*******************************************************************/
MiApp_DiscardMessage();
bReceivedMessage = TRUE;
/*******************************************************************/
// Following block update the total received and transmitted messages
// on the LCD of the demo board.
/*******************************************************************/
LCDTRXCount(TxNum, ++RxNum);
}
else
{
++m;
if(m > 8000)
{
m=0;
//LED_1 ^= 1;
MiApp_FlushTx();
MiApp_WriteData('H');
MiApp_WriteData('o');
MiApp_WriteData('l');
MiApp_WriteData('a');
MiApp_WriteData('a');
MiApp_WriteData('a');
MiApp_WriteData(0x0D);
MiApp_WriteData(0x0A);
MiApp_BroadcastPacket(FALSE);
}
if ( ConsoleIsGetReady() )
{
//ProcessMenu();
}
}
}
}
void main(void)
{
#define BAUDRG 77
BYTE SecNum = 0;
BOOL Tx_Success = FALSE;
BYTE Tx_Trials = 0, scanresult = 0;
/*******************************************************************/
// Initialize the system
/*******************************************************************/
ANCON0 = 0XFF; /*desactiva entradas analogicas*/
ANCON1 = 0XFF; /*desactiva entradas analogicas*/
PPSUnLock();
PPSOutput(PPS_RP10, PPS_TX2CK2); // TX2 RP17/RC6 icsp
PPSInput(PPS_RX2DT2, PPS_RP9); // RX2 RP18/RC7
PPSOutput(PPS_RP23, PPS_SDO2); // SDO2 RP23/RD6
PPSInput(PPS_SDI2, PPS_RP24); // SDI2 RP24/RD7
PPSOutput(PPS_RP22, PPS_SCK2); // SCK2 RP22/RD5
PPSLock();
System_PeripheralPinSelect( ExternalInterrupt3, 19); /*external interrupt 3 B3*/
BoardInit();
ConsoleInit();
Gpios_PinDirection(GPIOS_PORTC, 7, GPIOS_INPUT); /*pin C0 como salida para SDI*/
Gpios_PinDirection(GPIOS_PORTC, 6, GPIOS_OUTPUT); /*pin C1 como salida para SDO*/
//Gpios_PinDirection(GPIOS_PORTD, 4, GPIOS_OUTPUT); /*pin D4 como salida */
Open1USART(USART_TX_INT_OFF & USART_RX_INT_OFF & USART_EIGHT_BIT & USART_ASYNCH_MODE & USART_ADDEN_OFF, BAUDRG);
baud1USART(BAUD_IDLE_TX_PIN_STATE_HIGH & BAUD_IDLE_RX_PIN_STATE_HIGH & BAUD_AUTO_OFF & BAUD_WAKEUP_OFF & BAUD_16_BIT_RATE & USART_RX_INT_OFF);
Open2USART(USART_TX_INT_OFF & USART_RX_INT_OFF & USART_EIGHT_BIT & USART_ASYNCH_MODE & USART_ADDEN_OFF, BAUDRG);
baud2USART(BAUD_IDLE_TX_PIN_STATE_HIGH & BAUD_IDLE_RX_PIN_STATE_HIGH & BAUD_AUTO_OFF & BAUD_WAKEUP_OFF & BAUD_16_BIT_RATE & USART_RX_INT_OFF);
OpenTimer1( TIMER_INT_OFF &T1_16BIT_RW &T1_SOURCE_FOSC_4 & T1_PS_1_8 &T1_OSC1EN_OFF &T1_SYNC_EXT_OFF, TIMER_GATE_OFF & TIMER_GATE_INT_OFF);
Gpios_PinDirection(GPIOS_PORTD, 7, GPIOS_INPUT); /*pin C0 como salida para SDI*/
Gpios_PinDirection(GPIOS_PORTD, 6, GPIOS_OUTPUT); /*pin C1 como salida para SDO*/
Gpios_PinDirection(GPIOS_PORTD, 5, GPIOS_OUTPUT); /*pin C2 como salida para SCK*/
Spi_Init(SPI_PORT1, SPI_64DIV); /*Inicializamos SPI2*/
Spi_Init(SPI_PORT2, SPI_64DIV); /*Inicializamos SPI2*/
//Adc_Init(ADC_10BITS);
LED_1 = 1;
LED_2 = 0;
//RLY_1 = 0;
RLY_2 = 0;
ON_RADIO = 1;
ON_MAC = 1;
ON_TEMP = 1;
StartWirelessConnection();
//myDevicesRequiredStatus[0] = 0x55;
EEPROMRead(&myDevicesRequiredStatus, 0, 1);
if(myDevicesRequiredStatus[0] == 0x55)
{
RLY_1 = 1;
EEPROMCHG = 1;
ConsolePutROMString((ROM char *)"RELAY ON ");
}
if(myDevicesRequiredStatus[0] == 0xAA)
{
RLY_1 = 0;
EEPROMCHG = 0;
ConsolePutROMString((ROM char *)"RELAY OFF ");
}
for(j=0;j<10;j++)
{
DelayMs(50);
LED_1 ^= 1;
LED_2 ^= 1;
}
LED_1 = 0;
LED_2 = 0;
//RLY_1 = 0;
RLY_2 = 0;
TickScaler = 4;
EndDevStateMachine =0;
/*
while(!Tx_Success)
{
if(myChannel < 8)
scanresult = MiApp_SearchConnection(10, (0x00000001 << myChannel));
else if(myChannel < 16)
scanresult = MiApp_SearchConnection(10, (0x00000100 << (myChannel-8)));
else if(myChannel < 24)
scanresult = MiApp_SearchConnection(10, (0x00010000 << (myChannel-16)));
else
scanresult = MiApp_SearchConnection(10, (0x01000000 << (myChannel-24)));
if(scanresult == 0)
{
Tx_Trials++;
if(Tx_Trials > 2) break;
}
else Tx_Success = TRUE;
}
if(Tx_Success)
{
ConsolePutROMString((ROM char *)"RADIO OK ");
}
else
{
ConsolePutROMString((ROM char *)"RADIO FAIL ");
}
*/
//.VBGOE = 0;
//ANCON1bits.VBGEN = 1; // Enable Band gap reference voltage
//DelayMs(10);
//VBGResult = Adc_u16Read(15);
//ANCON1bits.VBGEN = 0; // Disable Bandgap
//Adc_Init(ADC_10BITS);
ANCON0 = 0xFF;
ANCON1 = 0x9F;
ANCON1bits.VBGEN = 1; // Enable Band gap reference voltage
ADCON0bits.VCFG = 0; // vreff VDD-VSS
ADCON0bits.CHS = 0x0F; // VBG channel select
ADCON1 = 0xBE;
ADCON0bits.ADON = 1;
//for(j=0;j<16;j++)
//{
//myDevicesOutputStatus[j] = j;
//}
//EEPROMWRITE(myDevicesOutputStatus,0,16);
//for(j=0;j<16;j++)
//{
//myDevicesOutputStatus[j] = 0;
//}
//DelayMs(500);
EEPROMRead(&myDevicesOutputStatus, 0, 16);
ConsolePutROMString((ROM char *)"EEPROM READ: ");
//PrintChar(TemperatureCalibrationValue);
for(j=0;j<1;j++)
{
PrintChar(myDevicesOutputStatus[j]);
}
SwTimer3 = 0;
SwTimer4 = 0;
TRISB&=0xEF; //JL: Configuro el pin B4 como salida si modificar el estado de los demas pines
while(1)
{
/*
WirelessTxRx();
WirelesStatus();
Bypass();
*/
//No se utilizaron
//Menu();
//Timer1Tick();
//WirelessTxRxPANCOORD();
//TaskScheduler();
//JLEstas funciones deben habilitarse para trabajar como repetidora
Timer1Tick();
Repeater();
}
}
