/*
** Main Function.
*/
int main(void)
{
unsigned char choice = 0;
/* Enable the clocks for McSPI0 module.*/
McSPI0ModuleClkConfig();
/* Perform Pin-Muxing for SPI0 Instance.*/
McSPIPinMuxSetup(0);
/* Perform Pin-Muxing for CS0 of SPI0 Instance.*/
McSPI0CSPinMuxSetup(MCSPI_CH_NUM);
/* Initialize the UART utility functions.*/
UARTStdioInit();
/* Enable IRQ in CPSR.*/
IntMasterIRQEnable();
UARTPuts("Here the McSPI controller on the SOC communicates with ",-1);
UARTPuts("the McSPI Flash.\r\n\r\n",-1);
/* Initialize the EDMA3 instance.*/
EDMA3Initialize();
/* Request EDMA3CC for Tx and Rx channels for SPI0. */
RequestEDMA3Channels();
/* Set up the McSPI instance.*/
McSPISetUp();
/* Enable the SPI Flash for writing to it. */
WriteEnable();
UARTPuts("Do you want to erase a sector of the flash before writing to it ?.", -1);
UARTPuts("\r\nInput y(Y)/n(N) to proceed.\r\n", -1);
choice = UARTGetc();
UARTPutc(choice);
if(('y' == choice) || ('Y' == choice))
{
/* Erasing the specified sector of SPI Flash. */
FlashSectorErase();
}
/* Enable the SPI Flash for writing to it. */
WriteEnable();
/* Write data of 1 page size into a page of Flash.*/
FlashPageProgram();
/* Read data of 1 page size from a page of flash.*/
ReadFromFlash();
/* Verify the data written to and read from Flash are same or not.*/
VerifyData();
while(1);
}
/*
** Main function.
*/
int main(void)
{
volatile char originalData[260] = {0};
volatile char readFlash[260] = {0};
unsigned int retVal = 0;
unsigned char choice;
/* Initializes the UART Instance for serial communication. */
UARTStdioInit();
UARTPuts("Welcome to SPI EDMA application.\r\n", -1);
UARTPuts("Here the SPI controller on the SoC communicates with", -1);
UARTPuts(" the SPI Flash present on the SoM.\r\n\r\n", -1);
/* Initializes the EDMA3 Instance. */
EDMA3Initialize();
/* Initializes the SPI1 Instance. */
SPIInitialize();
/* Request EDMA3CC for Tx and Rx channels for SPI1. */
RequestEDMA3Channels();
/* Enable SPI communication. */
SPIEnable(SOC_SPI_1_REGS);
/* Enable the SPI Flash for writing to it. */
WriteEnable();
UARTPuts("Do you want to erase a sector of the flash before writing to it ?.", -1);
UARTPuts("\r\nInput y(Y)/n(N) to proceed.\r\n", -1);
choice = UARTGetc();
UARTPutc(choice);
if(('y' == choice) || ('Y' == choice))
{
/* Erasing the specified sector of SPI Flash. */
FlashSectorErase();
}
WriteEnable();
/* Program a specified Page of the SPI Flash. */
FlashPageProgram(originalData);
/* Read the contents of the page that was previously written to. */
ReadFromFlash(readFlash);
/* Verify whether the written and the read contents are equal. */
retVal = verifyData(&originalData[4], &readFlash[4], 256);
if(TRUE == retVal)
{
UARTPuts("\r\nThe data in the Flash and the one written ", -1);
UARTPuts("to it are equal.\r\n", -1);
}
else
{
UARTPuts("\r\n\r\nThe data in the Flash and the one written to it", -1);
UARTPuts(" are not equal.\r\n", -1);
}
while(1);
}
/******************************************************************************
** INTERNAL FUNCTION DEFINITIONS
******************************************************************************/
int main(void)
{
volatile unsigned int count = 0x0FFFu;
unsigned int retVal = FALSE;
unsigned char choice = 0;
/* Enable the clocks for McSPI0 module.*/
McSPI0ModuleClkConfig();
/* Perform Pin-Muxing for SPI0 Instance */
McSPIPinMuxSetup(0);
/* Perform Pin-Muxing for CS0 of SPI0 Instance */
McSPI0CSPinMuxSetup(chNum);
/* Initialize the UART utility functions */
UARTStdioInit();
UARTPuts("Here the McSPI controller on the SoC communicates with", -1);
UARTPuts(" the SPI Flash.\r\n\r\n", -1);
/* Enable IRQ in CPSR.*/
IntMasterIRQEnable();
/* Map McSPI Interrupts to AINTC */
McSPI0AintcConfigure();
/* Do the necessary set up configurations for McSPI.*/
McSPISetUp();
/* Pass the write enable command to flash.*/
WriteEnable();
/* Wait until write enable command is successfully written to flash.*/
while(FALSE == retVal)
{
retVal = IsWriteSuccess();
}
retVal = FALSE;
UARTPuts("Do you want to erase a sector of the flash before ", -1);
UARTPuts("writing to it ?.", -1);
UARTPuts("\r\nInput y(Y)/n(N) to proceed.\r\n", -1);
choice = UARTGetc();
UARTPutc(choice);
if(('Y' == choice) || ('y' == choice))
{
/* Erase a sector of flash.*/
SectorErase();
}
/* Pass the write enable command to flash.*/
WriteEnable();
/* Wait until write enable command is successfully written to flash.*/
while(FALSE == retVal)
{
retVal = IsWriteSuccess();
}
/* Write data of 1 page size to flash.*/
WriteToFlash();
while(count--);
count = 0x0FFFu;
/* Read data of 1 page size from flash.*/
ReadFromFlash();
while(count--);
/* Verify the data written to and read from flash are same or not.*/
VerifyData();
while(1);
}