Пример #1
0
// This is a safe variant of the polygon offset, tailored for a single ExPolygon:
// a single polygon with multiple non-overlapping holes.
// Each contour and hole is offsetted separately, then the holes are subtracted from the outer contours.
ClipperLib::Paths _offset(const Slic3r::ExPolygon &expolygon, const float delta,
    ClipperLib::JoinType joinType, double miterLimit)
{
//    printf("new ExPolygon offset\n");
    // 1) Offset the outer contour.
    const float delta_scaled = delta * float(CLIPPER_OFFSET_SCALE);
    ClipperLib::Paths contours;
    {
        ClipperLib::Path input = Slic3rMultiPoint_to_ClipperPath(expolygon.contour);
        scaleClipperPolygon(input);
        ClipperLib::ClipperOffset co;
        if (joinType == jtRound)
            co.ArcTolerance = miterLimit * double(CLIPPER_OFFSET_SCALE);
        else
            co.MiterLimit = miterLimit;
        co.ShortestEdgeLength = double(std::abs(delta_scaled * CLIPPER_OFFSET_SHORTEST_EDGE_FACTOR));
        co.AddPath(input, joinType, ClipperLib::etClosedPolygon);
        co.Execute(contours, delta_scaled);
    }

    // 2) Offset the holes one by one, collect the results.
    ClipperLib::Paths holes;
    {
        holes.reserve(expolygon.holes.size());
        for (Polygons::const_iterator it_hole = expolygon.holes.begin(); it_hole != expolygon.holes.end(); ++ it_hole) {
            ClipperLib::Path input = Slic3rMultiPoint_to_ClipperPath_reversed(*it_hole);
            scaleClipperPolygon(input);
            ClipperLib::ClipperOffset co;
            if (joinType == jtRound)
                co.ArcTolerance = miterLimit * double(CLIPPER_OFFSET_SCALE);
            else
                co.MiterLimit = miterLimit;
            co.ShortestEdgeLength = double(std::abs(delta_scaled * CLIPPER_OFFSET_SHORTEST_EDGE_FACTOR));
            co.AddPath(input, joinType, ClipperLib::etClosedPolygon);
            ClipperLib::Paths out;
            co.Execute(out, - delta_scaled);
            holes.insert(holes.end(), out.begin(), out.end());
        }
    }

    // 3) Subtract holes from the contours.
    ClipperLib::Paths output;
    if (holes.empty()) {
        output = std::move(contours);
    } else {
        ClipperLib::Clipper clipper;
        clipper.Clear();
        clipper.AddPaths(contours, ClipperLib::ptSubject, true);
        clipper.AddPaths(holes, ClipperLib::ptClip, true);
        clipper.Execute(ClipperLib::ctDifference, output, ClipperLib::pftNonZero, ClipperLib::pftNonZero);
    }
    
    // 4) Unscale the output.
    unscaleClipperPolygons(output);
    return output;
}
Пример #2
0
// This is a safe variant of the polygon offset, tailored for a single ExPolygon:
// a single polygon with multiple non-overlapping holes.
// Each contour and hole is offsetted separately, then the holes are subtracted from the outer contours.
void offset(const Slic3r::ExPolygons &expolygons, ClipperLib::Paths* retval, const float delta,
    ClipperLib::JoinType joinType, double miterLimit)
{
//    printf("new ExPolygon offset\n");
    const float delta_scaled = delta * float(CLIPPER_OFFSET_SCALE);
    ClipperLib::Paths contours;
    ClipperLib::Paths holes;
    contours.reserve(expolygons.size());
    {
        size_t n_holes = 0;
        for (size_t i = 0; i < expolygons.size(); ++ i)
            n_holes += expolygons[i].holes.size();
        holes.reserve(n_holes);
    }

    for (Slic3r::ExPolygons::const_iterator it_expoly = expolygons.begin(); it_expoly != expolygons.end(); ++ it_expoly) {
        // 1) Offset the outer contour.
        {
            ClipperLib::Path input;
            Slic3rMultiPoint_to_ClipperPath(it_expoly->contour, &input);
            scaleClipperPolygon(input);
            ClipperLib::ClipperOffset co;
            if (joinType == jtRound)
                co.ArcTolerance = miterLimit * double(CLIPPER_OFFSET_SCALE);
            else
                co.MiterLimit = miterLimit;
            co.AddPath(input, joinType, ClipperLib::etClosedPolygon);
            ClipperLib::Paths out;
            co.Execute(out, delta_scaled);
            contours.insert(contours.end(), out.begin(), out.end());
        }

        // 2) Offset the holes one by one, collect the results.
        {
            for (Polygons::const_iterator it_hole = it_expoly->holes.begin(); it_hole != it_expoly->holes.end(); ++ it_hole) {
                ClipperLib::Path input;
                Slic3rMultiPoint_to_ClipperPath_reversed(*it_hole, &input);
                scaleClipperPolygon(input);
                ClipperLib::ClipperOffset co;
                if (joinType == jtRound)
                    co.ArcTolerance = miterLimit * double(CLIPPER_OFFSET_SCALE);
                else
                    co.MiterLimit = miterLimit;
                co.AddPath(input, joinType, ClipperLib::etClosedPolygon);
                ClipperLib::Paths out;
                co.Execute(out, - delta_scaled);
                holes.insert(holes.end(), out.begin(), out.end());
            }
        }
    }

    // 3) Subtract holes from the contours.
    ClipperLib::Paths output;
    {
        ClipperLib::Clipper clipper;
        clipper.Clear();
        clipper.AddPaths(contours, ClipperLib::ptSubject, true);
        clipper.AddPaths(holes, ClipperLib::ptClip, true);
        clipper.Execute(ClipperLib::ctDifference, *retval, ClipperLib::pftNonZero, ClipperLib::pftNonZero);
    }
    
    // 4) Unscale the output.
    unscaleClipperPolygons(*retval);
}
Пример #3
0
// This is a safe variant of the polygons offset, tailored for multiple ExPolygons.
// It is required, that the input expolygons do not overlap and that the holes of each ExPolygon don't intersect with their respective outer contours.
// Each ExPolygon is offsetted separately, then the offsetted ExPolygons are united.
ClipperLib::Paths _offset(const Slic3r::ExPolygons &expolygons, const float delta,
    ClipperLib::JoinType joinType, double miterLimit)
{
    const float delta_scaled = delta * float(CLIPPER_OFFSET_SCALE);
    // Offsetted ExPolygons before they are united.
    ClipperLib::Paths contours_cummulative;
    contours_cummulative.reserve(expolygons.size());
    // How many non-empty offsetted expolygons were actually collected into contours_cummulative?
    // If only one, then there is no need to do a final union.
    size_t expolygons_collected = 0;
    for (Slic3r::ExPolygons::const_iterator it_expoly = expolygons.begin(); it_expoly != expolygons.end(); ++ it_expoly) {
        // 1) Offset the outer contour.
        ClipperLib::Paths contours;
        {
            ClipperLib::Path input = Slic3rMultiPoint_to_ClipperPath(it_expoly->contour);
            scaleClipperPolygon(input);
            ClipperLib::ClipperOffset co;
            if (joinType == jtRound)
                co.ArcTolerance = miterLimit * double(CLIPPER_OFFSET_SCALE);
            else
                co.MiterLimit = miterLimit;
            co.ShortestEdgeLength = double(std::abs(delta_scaled * CLIPPER_OFFSET_SHORTEST_EDGE_FACTOR));
            co.AddPath(input, joinType, ClipperLib::etClosedPolygon);
            co.Execute(contours, delta_scaled);
        }
        if (contours.empty())
            // No need to try to offset the holes.
            continue;

        if (it_expoly->holes.empty()) {
            // No need to subtract holes from the offsetted expolygon, we are done.
            contours_cummulative.insert(contours_cummulative.end(), contours.begin(), contours.end());
            ++ expolygons_collected;
        } else {
            // 2) Offset the holes one by one, collect the offsetted holes.
            ClipperLib::Paths holes;
            {
                for (Polygons::const_iterator it_hole = it_expoly->holes.begin(); it_hole != it_expoly->holes.end(); ++ it_hole) {
                    ClipperLib::Path input = Slic3rMultiPoint_to_ClipperPath_reversed(*it_hole);
                    scaleClipperPolygon(input);
                    ClipperLib::ClipperOffset co;
                    if (joinType == jtRound)
                        co.ArcTolerance = miterLimit * double(CLIPPER_OFFSET_SCALE);
                    else
                        co.MiterLimit = miterLimit;
                    co.ShortestEdgeLength = double(std::abs(delta_scaled * CLIPPER_OFFSET_SHORTEST_EDGE_FACTOR));
                    co.AddPath(input, joinType, ClipperLib::etClosedPolygon);
                    ClipperLib::Paths out;
                    co.Execute(out, - delta_scaled);
                    holes.insert(holes.end(), out.begin(), out.end());
                }
            }

            // 3) Subtract holes from the contours.
            if (holes.empty()) {
                // No hole remaining after an offset. Just copy the outer contour.
                contours_cummulative.insert(contours_cummulative.end(), contours.begin(), contours.end());
                ++ expolygons_collected;
            } else if (delta < 0) {
                // Negative offset. There is a chance, that the offsetted hole intersects the outer contour. 
                // Subtract the offsetted holes from the offsetted contours.
                ClipperLib::Clipper clipper;
                clipper.Clear();
                clipper.AddPaths(contours, ClipperLib::ptSubject, true);
                clipper.AddPaths(holes, ClipperLib::ptClip, true);
                ClipperLib::Paths output;
                clipper.Execute(ClipperLib::ctDifference, output, ClipperLib::pftNonZero, ClipperLib::pftNonZero);
                if (! output.empty()) {
                    contours_cummulative.insert(contours_cummulative.end(), output.begin(), output.end());
                    ++ expolygons_collected;
                } else {
                    // The offsetted holes have eaten up the offsetted outer contour.
                }
            } else {
                // Positive offset. As long as the Clipper offset does what one expects it to do, the offsetted hole will have a smaller
                // area than the original hole or even disappear, therefore there will be no new intersections.
                // Just collect the reversed holes.
                contours_cummulative.reserve(contours.size() + holes.size());
                contours_cummulative.insert(contours_cummulative.end(), contours.begin(), contours.end());
                // Reverse the holes in place.
                for (size_t i = 0; i < holes.size(); ++ i)
                    std::reverse(holes[i].begin(), holes[i].end());
                contours_cummulative.insert(contours_cummulative.end(), holes.begin(), holes.end());
                ++ expolygons_collected;
            }
        }
    }

    // 4) Unite the offsetted expolygons.
    ClipperLib::Paths output;
    if (expolygons_collected > 1 && delta > 0) {
        // There is a chance that the outwards offsetted expolygons may intersect. Perform a union.
        ClipperLib::Clipper clipper;
        clipper.Clear(); 
        clipper.AddPaths(contours_cummulative, ClipperLib::ptSubject, true);
        clipper.Execute(ClipperLib::ctUnion, output, ClipperLib::pftNonZero, ClipperLib::pftNonZero);
    } else {
        // Negative offset. The shrunk expolygons shall not mutually intersect. Just copy the output.
        output = std::move(contours_cummulative);
    }
    
    // 4) Unscale the output.
    unscaleClipperPolygons(output);
    return output;
}