/**
* @brief this function sets the destination address
* @param uint8_t adress
* @retval None
*/
void Spirit1SetDestinationAddress(uint8_t address)
{
#if defined(USE_STack_PROTOCOL)
/* Destination address */
SpiritPktStackSetDestinationAddress(address);
#elif defined(USE_BASIC_PROTOCOL)
/* destination address */
SpiritPktBasicSetDestinationAddress(address);
#endif
}
/**
* @brief System main function.
* @param None
* @retval None
*/
void main (void)
{
SDK_SYSTEM_CONFIG();
//#ifdef USE_VCOM
//#ifdef STM8L
// SdkEvalComInit(115200,USART_WordLength_8b,USART_StopBits_1,USART_Parity_No,(USART_Mode_TypeDef)(USART_Mode_Rx | USART_Mode_Tx));
//#elif SDK
// /* VC config */
// SdkEvalVCInit();
// while(bDeviceState != CONFIGURED);
//#endif
//#endif
/* Spirit ON */
SpiritEnterShutdown();
SpiritExitShutdown();
SpiritManagementWaExtraCurrent();
//#ifdef STM8L
// /* Manually set the XTAL_FREQUENCY */
// SpiritRadioSetXtalFrequency(XTAL_FREQUENCY);
// /* Initialize the frequency offset variable to compensate XTAL offset */
// xRadioInit.lFrequencyBase = xRadioInit.lFrequencyBase + FREQUENCY_OFFSET;
// /* Initialize the signals to drive the range extender application board */
// RANGE_EXT_INIT(RANGE_TYPE);
//#elif SDK
SpiritManagementIdentificationRFBoard();
/* if the board has eeprom, we can compensate the offset calling SpiritManagementGetOffset
(if eeprom is not present this fcn will return 0) */
xRadioInit.lFrequencyBase = xRadioInit.lFrequencyBase + SpiritManagementGetOffset();
/* Initialize the signals to drive the range extender application board */
SpiritManagementRangeExtInit();
//#endif
/* uC IRQ config */
SdkEvalM2SGpioInit(M2S_GPIO_3,M2S_MODE_EXTI_IN);
/* Spirit IRQ config */
SpiritGpioInit(&xGpioIRQ);
/* uC IRQ enable */
//#ifdef STM8L
// enableInterrupts();
//#elif SDK
SdkEvalM2SGpioInterruptCmd(M2S_GPIO_3,0x0A,0x0A,ENABLE);
//#endif
/* Spirit Radio config */
SpiritRadioInit(&xRadioInit);
/* Spirit Radio set power */
SpiritRadioSetPALeveldBm(7,POWER_DBM);
SpiritRadioSetPALevelMaxIndex(7);
/* Spirit Packet config */
SpiritPktBasicInit(&xBasicInit);
SpiritPktBasicAddressesInit(&xAddressInit);
/* Spirit IRQs enable */
SpiritIrqDeInit(NULL);
SpiritIrq(TX_DATA_SENT , S_ENABLE);
/* payload length config */
SpiritPktBasicSetPayloadLength(20);
/* destination address.
By default it is not used because address is disabled, see struct xAddressInit*/
SpiritPktBasicSetDestinationAddress(0x35);
/* IRQ registers blanking */
SpiritIrqClearStatus();
/* infinite loop */
while (1){
//#ifdef USE_VCOM
// printf("A data to transmit: [");
//
// for(uint8_t i=0 ; i<20 ; i++)
// printf("%d ", vectcTxBuff[i]);
// printf("]\n\r");
//#endif
/* fit the TX FIFO */
SpiritCmdStrobeFlushTxFifo();
SpiritSpiWriteLinearFifo(20, vectcTxBuff);
/* send the TX command */
SpiritCmdStrobeTx();
/* wait for TX done */
while(!xTxDoneFlag);
xTxDoneFlag = RESET;
/* pause between two transmissions */
SdkDelayMs(500);
}
}