BOOL PutTelnetConsole(char c)
{
TCP_SOCKET MySocket;
WORD i;
MySocket = hTelnetSockets[0];
if (vTelnetStates[0] != SM_AUTHENTICATED) return 1;
if (termbufidx < MAXTERMBUF)
{
termbuf[termbufidx++] = c;
termbuftimer = 0;
return 1;
}
if (TCPIsPutReady(MySocket) < termbufidx)
{
StackTask();
StackApplications();
return 0;
}
for(i = 0; i < termbufidx; i++) TCPPut(MySocket,termbuf[i]);
TCPFlush(MySocket);
termbufidx = 0;
termbuftimer = 0;
return 0;
}
void main()
{
union {
unsigned int32 hours;
unsigned int8 minutes;
unsigned int8 seconds;} upTime;
TICK_TYPE CurrentTick,PreviousUDPTick,PreviousSATick;
resetStatus = (RCON & 0b00111111) | !(STKPTR & 0b11000000); // Get the Reset Status
RCON = RCON | 0b00111111; //Reset RCON Reset flags... (Reset Register)
STKPTR = STKPTR & 0b00111111; // Clear Stack Overflow/Underflow flags
PortInit();
OutputInit();
restart_wdt();
romEZHRInit(); //set up default ezhr settings
eeROMinit(); //set up default eprom settings
IPAddressInit(); //set up MAC and default IP addresses
delay_ms(500);
ADCInit(); //set up ADC ports
iniADCParams();
SerialInit(); //set up serial ports
TickInit(); //set up tick timer
enable_interrupts(INT_RDA);
enable_interrupts(GLOBAL);
StackInit();
WritePHYReg(ERXFCON,EthernetRXfilterSetting); // Allow only uni & multi
SetLEDConfig(E_LED_CONFIG); // swap LED's
output_high(E_SW_PWR_DN); // Power Ethernet Switch
output_high(E_SW_RST);
output_low(RS485_TXEN);
output_high(RS485_RXDIS);
output_high(RS232_F_OFF);
output_high(RS232_F_ON);
CurrentTick = PreviousUDPTick = get_ticks();
UDPSampleRate = eeReadUDPRate() * TICKS_PER_MILLISECOND;
portControlInit();
while(TRUE)
{
CurrentTick = get_ticks();
restart_wdt();
StackTask();
restart_wdt();
MyTCPTask();//handles TCP connections
restart_wdt();
setIO();// checks voltage status and sets ports accordingly
//! if(CurrentTick-PreviousUDPTick >= UDPSampleRate)
//! {
//! currentRoutine=UDPTASK;
//! BOOL UDPDone = MyUDPTask();
//! if(UDPDone)
//! {
//! PreviousUDPTick=CurrentTick;
//! }
//! }
StackApplications();
}
}
int main() {
DWORD t = 0;
//Needed because a bug in picc-18?
MIWRL=0;
MIWRH=0;
TRISA = 0;
TRISB = 0;
TRISC = 0;
TRISD = 0;
TRISE = 0;
TRISF = 0;
TRISG = 0;
PORTA=0;
PORTB=0;
PORTC=0;
PORTD=0;
PORTE=0;
PORTF=0;
OSCTUNE = 0x40; //Speed up to 41.67 MHz
//Turn off AD
ADCON1 = 0x0F;
#if defined(DEBUG) && defined(_18F87J60)
initUsart2();
#endif
initTransmitter();
initReceiver();
initPwm();
initInterrupts();
initAppConfig();
initWDT();
TickInit();
StackInit();
//Set the LED on the connector
SetLEDConfig(0x3742); //See MAC.h for the values
printf("Telldus TellStick Net v%s\r\n", FIRMWARE_VERSION);
while(1) {
StackTask();
StackApplications();
if(TickGet() - t >= TICK_SECOND) {
t = TickGet();
}
#if defined(DEBUG)
debugTask();
#endif
rfReceiveTask();
discoveryTask();
ClrWdt();
}
return 42;
}
BOOL PutTelnetConsole(char c)
{
BYTE vTelnetSession,nconn;
TCP_SOCKET MySocket;
nconn = 0;
for(vTelnetSession = 0; vTelnetSession < MAX_TELNET_CONNECTIONS; vTelnetSession++)
{
if (vTelnetStates[vTelnetSession] == SM_AUTHENTICATED) nconn++;
}
nconn = 1;
if (nconn > 0)
{
StackTask();
StackApplications();
}
for(vTelnetSession = 0; vTelnetSession < MAX_TELNET_CONNECTIONS; vTelnetSession++)
{
// Load up static state information for this session
MySocket = hTelnetSockets[vTelnetSession];
if (vTelnetStates[vTelnetSession] != SM_AUTHENTICATED) continue;
if (TCPIsPutReady(MySocket) < 1)
{
StackTask();
StackApplications();
return 0;
}
}
for(vTelnetSession = 0; vTelnetSession < MAX_TELNET_CONNECTIONS; vTelnetSession++)
{
// Load up static state information for this session
MySocket = hTelnetSockets[vTelnetSession];
if (vTelnetStates[vTelnetSession] != SM_AUTHENTICATED) continue;
TCPPut(MySocket,c);
TCPFlush(MySocket);
}
return 1;
}
/****************************************************************************
Function:
void ChipKITPeriodicTasks(void)
Description:
This routine will run the periodic tasks needed to keep the Ethernet
stack alive and to run the tasks such as ping or DHCP as part of supporting the stack.
Precondition:
None
Parameters:
None - None
Returns:
None
Remarks:
This funciton needs to be called on a regular basis in order to service
incoming TCPIP / UDP tasks. If it is not called the stack will freeze.
Most Arduino interface APIs specified in the file call ChipKITPeriodicTasks
implicitly so that it is called at the right time to execution the stack
functions. But this routine is made available to the sketch so that the
sketch can keep the stack alive while the sketch is idle.
***************************************************************************/
void ChipKITPeriodicTasks(void)
{
// This task performs normal stack task including checking
// for incoming packet, type of packet and calling
// appropriate stack entity to process it.
StackTask();
// an annoying thing is that the MAL will not hold on to the
// UDP buffer for another iteration of StackTask, so we must
// buffer the UDP data so we don't lose it.
ChipKITUDPUpdateBufferCache();
// This tasks invokes each of the core stack application tasks
StackApplications();
}
void ProcessTelnetTimer(void)
{
TCP_SOCKET MySocket;
WORD i;
MySocket = hTelnetSockets[0];
if (vTelnetStates[0] != SM_AUTHENTICATED) return;
if (termbufidx < 1) return;
if (TCPIsPutReady(MySocket) < termbufidx)
{
StackTask();
StackApplications();
return;
}
for(i = 0; i < termbufidx; i++) TCPPut(MySocket,termbuf[i]);
termbufidx = 0;
termbuftimer = 0;
TCPFlush(MySocket);
return;
}
void MyWIFI_Task() {
static DWORD dwLastIP = 0;
char theStr[64];
// This task performs normal stack task including checking
// for incoming packet, type of packet and calling
// appropriate stack entity to process it.
StackTask();
// This tasks invokes each of the core stack application tasks
StackApplications();
// Process application specific tasks
#if defined(STACK_USE_SMTP_CLIENT)
MyWIFI_SMTP();
#endif
#if defined(STACK_USE_ICMP_CLIENT)
MyWIFI_Ping();
#endif
#if defined(STACK_USE_SNTP_CLIENT)
#endif
// If the local IP address has changed (ex: due to DHCP lease change)
// write the new IP address to the Console and Announce service
if(dwLastIP != AppConfig.MyIPAddr.Val) {
dwLastIP = AppConfig.MyIPAddr.Val;
sprintf(theStr, "New IP Address : %u.%u.%u.%u\n", AppConfig.MyIPAddr.v[0], AppConfig.MyIPAddr.v[1], AppConfig.MyIPAddr.v[2], AppConfig.MyIPAddr.v[3]);
MyConsole_SendMsg(theStr);
#if defined(STACK_USE_ANNOUNCE)
AnnounceIP();
#endif
}
}
int main(void)
#endif
{
// static DWORD t = 0;
static DWORD dwLastIP = 0;
#if defined (EZ_CONFIG_STORE)
// static DWORD ButtonPushStart = 0;
#endif
// Initialize application specific hardware
InitializeBoard();
// Initialize stack-related hardware components that may be
// required by the UART configuration routines
TickInit();
MPFSInit();
InitDataBuffers();
Slave_SpiInit();
// Initialize Stack and application related NV variables into AppConfig.
InitAppConfig();
// Initiates board setup process if button is depressed
// on startup
/*
#if defined (WIFI_BOARD_FOC_HUB)
XEEBeginWrite(0x0000);
XEEWrite(0xFF);
XEEWrite(0xFF);
XEEEndWrite();
#else
if(BUTTON0_IO == 0u)
{
#if defined(EEPROM_CS_TRIS) || defined(SPIFLASH_CS_TRIS)
// Invalidate the EEPROM contents if BUTTON0 is held down for more than 4 seconds
DWORD StartTime = TickGet();
LED_PUT(0x00);
while(BUTTON0_IO == 0u)
{
if(TickGet() - StartTime > 4*TICK_SECOND)
{
#if defined(EEPROM_CS_TRIS)
XEEBeginWrite(0x0000);
XEEWrite(0xFF);
XEEWrite(0xFF);
XEEEndWrite();
#elif defined(SPIFLASH_CS_TRIS)
SPIFlashBeginWrite(0x0000);
SPIFlashWrite(0xFF);
SPIFlashWrite(0xFF);
#endif
#if defined(STACK_USE_UART)
putrsUART("\r\n\r\nBUTTON0 held for more than 4 seconds. Default settings restored.\r\n\r\n");
#endif
LED_PUT(0x0F);
while((LONG)(TickGet() - StartTime) <= (LONG)(9*TICK_SECOND/2));
LED_PUT(0x00);
while(BUTTON0_IO == 0u);
Reset();
break;
}
}
#endif
#if defined(STACK_USE_UART)
DoUARTConfig();
#endif
}
#endif
*/
// Initialize core stack layers (MAC, ARP, TCP, UDP) and
// application modules (HTTP, SNMP, etc.)
StackInit();
#if defined ( EZ_CONFIG_SCAN )
WFInitScan();
#endif
#if defined(WF_CS_TRIS)
WF_Connect();
#endif
#if defined(STACK_USE_ZEROCONF_LINK_LOCAL)
ZeroconfLLInitialize();
#endif
#if defined(STACK_USE_ZEROCONF_MDNS_SD)
mDNSInitialize(MY_DEFAULT_HOST_NAME);
mDNSServiceRegister(
(const char *) "DemoWebServer", // base name of the service
"_http._tcp.local", // type of the service
80, // TCP or UDP port, at which this service is available
((const BYTE *)"path=/index.htm"), // TXT info
1, // auto rename the service when if needed
NULL, // no callback function
NULL // no application context
);
mDNSMulticastFilterRegister();
#endif
// Now that all items are initialized, begin the co-operative
// multitasking loop. This infinite loop will continuously
// execute all stack-related tasks, as well as your own
// application's functions. Custom functions should be added
// at the end of this loop.
// Note that this is a "co-operative mult-tasking" mechanism
// where every task performs its tasks (whether all in one shot
// or part of it) and returns so that other tasks can do their
// job.
// If a task needs very long time to do its job, it must be broken
// down into smaller pieces so that other tasks can have CPU time.
while(1)
{
/*
#if defined (EZ_CONFIG_STORE)
// Hold button3 for 4 seconds to reset to defaults.
if (BUTTON3_IO == 0u) { // Button is pressed
if (ButtonPushStart == 0) //Just pressed
ButtonPushStart = TickGet();
else
if(TickGet() - ButtonPushStart > 4*TICK_SECOND)
RestoreWifiConfig();
}
else
{
ButtonPushStart = 0; //Button release reset the clock
}
if (AppConfig.saveSecurityInfo)
{
// set true by WF_ProcessEvent after connecting to a new network
// get the security info, and if required, push the PSK to EEPROM
if ((AppConfig.SecurityMode == WF_SECURITY_WPA_WITH_PASS_PHRASE) ||
(AppConfig.SecurityMode == WF_SECURITY_WPA2_WITH_PASS_PHRASE) ||
(AppConfig.SecurityMode == WF_SECURITY_WPA_AUTO_WITH_PASS_PHRASE))
{
// only need to save when doing passphrase
tWFCPElements profile;
UINT8 connState;
UINT8 connID;
WF_CMGetConnectionState(&connState, &connID);
WF_CPGetElements(connID, &profile);
memcpy((char*)AppConfig.SecurityKey, (char*)profile.securityKey, 32);
AppConfig.SecurityMode--; // the calc psk is exactly one below for each passphrase option
AppConfig.SecurityKeyLength = 32;
SaveAppConfig(&AppConfig);
}
AppConfig.saveSecurityInfo = FALSE;
}
#endif // EZ_CONFIG_STORE
#if defined (STACK_USE_EZ_CONFIG)
// Blink LED0 twice per sec when unconfigured, once per sec after config
if((TickGet() - t >= TICK_SECOND/(4ul - (CFGCXT.isWifiDoneConfigure*2ul))))
#else
// Blink LED0 (right most one) every second.
if(TickGet() - t >= TICK_SECOND/2ul)
#endif // STACK_USE_EZ_CONFIG
{
t = TickGet();
LED0_IO ^= 1;
}
*/
// This task performs normal stack task including checking
// for incoming packet, type of packet and calling
// appropriate stack entity to process it.
StackTask();
// This tasks invokes each of the core stack application tasks
StackApplications();
// Process command received from Motherboad via SPI interface.
//ProcessReceivedSpiCmds();
#if defined(STACK_USE_ZEROCONF_LINK_LOCAL)
ZeroconfLLProcess();
#endif
#if defined(STACK_USE_ZEROCONF_MDNS_SD)
mDNSProcess();
// Use this function to exercise service update function
// HTTPUpdateRecord();
#endif
// Process application specific tasks here.
// For this demo app, this will include the Generic TCP
// client and servers, and the SNMP, Ping, and SNMP Trap
// demos. Following that, we will process any IO from
// the inputs on the board itself.
// Any custom modules or processing you need to do should
// go here.
#if defined (WIFI_BOARD_FOC_HUB)
ProcessWiFiTransfers(); // Handles TCP/IP transfers
DoWiFiWork(); // Handles SPI incoming requests
#endif
#if defined(WF_CONSOLE)
WFConsoleProcess();
IperfAppCall();
WFConsoleProcessEpilogue();
#endif
#if defined(STACK_USE_GENERIC_TCP_CLIENT_EXAMPLE)
GenericTCPClient();
#endif
#if defined(STACK_USE_GENERIC_TCP_SERVER_EXAMPLE)
GenericTCPServer();
#endif
#if defined(STACK_USE_SMTP_CLIENT)
SMTPDemo();
#endif
#if defined(STACK_USE_ICMP_CLIENT)
PingDemo();
#endif
#if defined(STACK_USE_SNMP_SERVER) && !defined(SNMP_TRAP_DISABLED)
//User should use one of the following SNMP demo
// This routine demonstrates V1 or V2 trap formats with one variable binding.
SNMPTrapDemo();
#if defined(SNMP_STACK_USE_V2_TRAP) || defined(SNMP_V1_V2_TRAP_WITH_SNMPV3)
//This routine provides V2 format notifications with multiple (3) variable bindings
//User should modify this routine to send v2 trap format notifications with the required varbinds.
//SNMPV2TrapDemo();
#endif
if(gSendTrapFlag)
SNMPSendTrap();
#endif
#if defined ( WF_CONSOLE ) && defined ( EZ_CONFIG_SCAN )
WFDisplayScanMgr();
#endif
#if defined(STACK_USE_BERKELEY_API)
BerkeleyTCPClientDemo();
BerkeleyTCPServerDemo();
BerkeleyUDPClientDemo();
#endif
// If the local IP address has changed (ex: due to DHCP lease change)
// write the new IP address to the LCD display, UART, and Announce
// service
if(dwLastIP != AppConfig.MyIPAddr.Val)
{
dwLastIP = AppConfig.MyIPAddr.Val;
WiFiInfo.CurrentConfigPtr->MyIPAddr.Val = AppConfig.MyIPAddr.Val;
#if defined(STACK_USE_UART)
putrsUART((ROM char*)"\r\nNew IP Address: ");
#endif
DisplayIPValue(AppConfig.MyIPAddr);
#if defined(STACK_USE_UART)
putrsUART((ROM char*)"\r\n");
#endif
#if defined(STACK_USE_ANNOUNCE)
AnnounceIP();
#endif
#if defined(STACK_USE_ZEROCONF_MDNS_SD)
mDNSFillHostRecord();
#endif
}
}
}
int main(void)
#endif
{
static DWORD t = 0;
static DWORD dwLastIP = 0;
// Initialize application specific hardware
InitializeBoard();
#if defined(USE_LCD)
// Initialize and display the stack version on the LCD
LCDInit();
DelayMs(100);
strcpypgm2ram((char*)LCDText, "WebVend Demo App"
" ");
LCDUpdate();
#endif
// Initialize stack-related hardware components that may be
// required by the UART configuration routines
TickInit();
#if defined(STACK_USE_MPFS2)
MPFSInit();
#endif
// Initialize Stack and application related NV variables into AppConfig.
InitAppConfig();
// Initiates board setup process if button is depressed
// on startup
if(BUTTON0_IO == 0u)
{
#if defined(EEPROM_CS_TRIS) || defined(SPIFLASH_CS_TRIS)
// Invalidate the EEPROM contents if BUTTON0 is held down for more than 4 seconds
DWORD StartTime = TickGet();
LED_PUT(0x00);
while(BUTTON0_IO == 0u)
{
if(TickGet() - StartTime > 4*TICK_SECOND)
{
#if defined(EEPROM_CS_TRIS)
XEEBeginWrite(0x0000);
XEEWrite(0xFF);
XEEWrite(0xFF);
XEEEndWrite();
#elif defined(SPIFLASH_CS_TRIS)
SPIFlashBeginWrite(0x0000);
SPIFlashWrite(0xFF);
SPIFlashWrite(0xFF);
#endif
#if defined(STACK_USE_UART)
putrsUART("\r\n\r\nBUTTON0 held for more than 4 seconds. Default settings restored.\r\n\r\n");
#endif
LED_PUT(0x0F);
while((LONG)(TickGet() - StartTime) <= (LONG)(9*TICK_SECOND/2));
LED_PUT(0x00);
while(BUTTON0_IO == 0u);
Reset();
break;
}
}
#endif
}
// Initialize core stack layers (MAC, ARP, TCP, UDP) and
// application modules (HTTP, SNMP, etc.)
StackInit();
#if defined(WF_CS_TRIS)
WF_Connect();
#endif
// Initialize any application-specific modules or functions/
// For this demo application, this only includes the
// UART 2 TCP Bridge
#if defined(STACK_USE_UART2TCP_BRIDGE)
UART2TCPBridgeInit();
#endif
#if defined(STACK_USE_ZEROCONF_LINK_LOCAL)
ZeroconfLLInitialize();
#endif
#if defined(STACK_USE_ZEROCONF_MDNS_SD)
mDNSInitialize(MY_DEFAULT_HOST_NAME);
mDNSServiceRegister(
(const char *) "DemoWebServer", // base name of the service
"_http._tcp.local", // type of the service
80, // TCP or UDP port, at which this service is available
((const BYTE *)"path=/index.htm"), // TXT info
1, // auto rename the service when if needed
NULL, // no callback function
NULL // no application context
);
mDNSMulticastFilterRegister();
#endif
// Now that all items are initialized, begin the co-operative
// multitasking loop. This infinite loop will continuously
// execute all stack-related tasks, as well as your own
// application's functions. Custom functions should be added
// at the end of this loop.
// Note that this is a "co-operative mult-tasking" mechanism
// where every task performs its tasks (whether all in one shot
// or part of it) and returns so that other tasks can do their
// job.
// If a task needs very long time to do its job, it must be broken
// down into smaller pieces so that other tasks can have CPU time.
while(1)
{
// Blink LED0 (right most one) every second.
if(TickGet() - t >= TICK_SECOND/2ul)
{
t = TickGet();
LED0_IO ^= 1;
}
// This task performs normal stack task including checking
// for incoming packet, type of packet and calling
// appropriate stack entity to process it.
StackTask();
// This tasks invokes each of the core stack application tasks
StackApplications();
#if defined(STACK_USE_ZEROCONF_LINK_LOCAL)
ZeroconfLLProcess();
#endif
#if defined(STACK_USE_ZEROCONF_MDNS_SD)
mDNSProcess();
// Use this function to exercise service update function
// HTTPUpdateRecord();
#endif
// Process application specific tasks here.
// For this demo app, this will include the Generic TCP
// client and servers, and the SNMP, Ping, and SNMP Trap
// demos. Following that, we will process any IO from
// the inputs on the board itself.
// Any custom modules or processing you need to do should
// go here.
ProcessIO();
// If the local IP address has changed (ex: due to DHCP lease change)
// write the new IP address to the LCD display, UART, and Announce
// service
if(dwLastIP != AppConfig.MyIPAddr.Val)
{
dwLastIP = AppConfig.MyIPAddr.Val;
#if defined(STACK_USE_UART)
putrsUART((ROM char*)"\r\nNew IP Address: ");
#endif
// If not vending, show the new IP
if(smVend == SM_IDLE || smVend == SM_DISPLAY_WAIT)
{
memcpypgm2ram(LCDText, "WebVend Demo App", 16);
DisplayIPValue(AppConfig.MyIPAddr); // Print to UART
#if defined(STACK_USE_UART)
putrsUART((ROM char*)"\r\n");
#endif
displayTimeout = TickGet() + 2*TICK_SECOND;
smVend = SM_DISPLAY_WAIT;
}
#if defined(STACK_USE_ANNOUNCE)
AnnounceIP();
#endif
#if defined(STACK_USE_ZEROCONF_MDNS_SD)
mDNSFillHostRecord();
#endif
}
}
}
int main(void)
#endif
{
static DWORD t = 0;
static DWORD dwLastIP = 0;
#if defined (EZ_CONFIG_STORE)
static DWORD ButtonPushStart = 0;
#endif
#if (MY_DEFAULT_NETWORK_TYPE == WF_SOFT_AP)
UINT8 channelList[] = MY_DEFAULT_CHANNEL_LIST_PRESCAN; // WF_PRESCAN
tWFScanResult bssDesc;
#endif
// Initialize application specific hardware
InitializeBoard();
#if defined(USE_LCD)
// Initialize and display the stack version on the LCD
LCDInit();
DelayMs(100);
strcpypgm2ram((char*)LCDText, "TCPStack " TCPIP_STACK_VERSION " "
" ");
LCDUpdate();
#endif
// Initialize stack-related hardware components that may be
// required by the UART configuration routines
TickInit();
#if defined(STACK_USE_MPFS2)
MPFSInit();
#endif
// Initialize Stack and application related NV variables into AppConfig.
InitAppConfig();
// Initiates board setup process if button is depressed
// on startup
if(BUTTON0_IO == 0u)
{
#if defined(EEPROM_CS_TRIS) || defined(SPIFLASH_CS_TRIS)
// Invalidate the EEPROM contents if BUTTON0 is held down for more than 4 seconds
DWORD StartTime = TickGet();
LED_PUT(0x00);
while(BUTTON0_IO == 0u)
{
if(TickGet() - StartTime > 4*TICK_SECOND)
{
#if defined(EEPROM_CS_TRIS)
XEEBeginWrite(0x0000);
XEEWrite(0xFF);
XEEWrite(0xFF);
XEEEndWrite();
#elif defined(SPIFLASH_CS_TRIS)
SPIFlashBeginWrite(0x0000);
SPIFlashWrite(0xFF);
SPIFlashWrite(0xFF);
#endif
#if defined(STACK_USE_UART)
putrsUART("\r\n\r\nBUTTON0 held for more than 4 seconds. Default settings restored.\r\n\r\n");
#endif
LED_PUT(0x0F);
while((LONG)(TickGet() - StartTime) <= (LONG)(9*TICK_SECOND/2));
LED_PUT(0x00);
while(BUTTON0_IO == 0u);
Reset();
break;
}
}
#endif
#if defined(STACK_USE_UART)
DoUARTConfig();
#endif
}
// Initialize core stack layers (MAC, ARP, TCP, UDP) and
// application modules (HTTP, SNMP, etc.)
StackInit();
#if defined ( EZ_CONFIG_SCAN )
WFInitScan();
#endif
#if (MY_DEFAULT_NETWORK_TYPE == WF_SOFT_AP)
// WF_PRESCAN: Pre-scan before starting up as SoftAP mode
WF_CASetScanType(MY_DEFAULT_SCAN_TYPE);
WF_CASetChannelList(channelList, sizeof(channelList));
if (WFStartScan() == WF_SUCCESS)
{
SCAN_SET_DISPLAY(SCANCXT.scanState);
SCANCXT.displayIdx = 0;
//putsUART("main: Prescan WFStartScan() success ................. \r\n");
}
// Needed to trigger g_scan_done
WFRetrieveScanResult(0, &bssDesc);
#else
#if defined(WF_CS_TRIS)
WF_Connect();
#endif // defined(WF_CS_TRIS)
#endif // (MY_DEFAULT_NETWORK_TYPE == WF_SOFT_AP)
// Initialize any application-specific modules or functions/
// For this demo application, this only includes the
// UART 2 TCP Bridge
#if defined(STACK_USE_UART2TCP_BRIDGE)
UART2TCPBridgeInit();
#endif
#if defined(STACK_USE_ZEROCONF_LINK_LOCAL)
ZeroconfLLInitialize();
#endif
#if defined(STACK_USE_ZEROCONF_MDNS_SD)
mDNSInitialize(MY_DEFAULT_HOST_NAME);
#if defined(STACK_USE_TCP_MOBILE_APP_SERVER)
mDNSServiceRegister(
(const char *) "HomeControlServer", // base name of the service
"_home-control._tcp.local", // type of the service
27561, // TCP or UDP port, at which this service is available
((const BYTE *)"control home devices"), // TXT info
1, // auto rename the service when if needed
NULL, // no callback function
NULL // no application context
);
#else /* !defined(STACK_USE_TCP_MOBILE_APP_SERVER) */
mDNSServiceRegister(
(const char *) "DemoWebServer", // base name of the service
"_http._tcp.local", // type of the service
80, // TCP or UDP port, at which this service is available
((const BYTE *)"path=/index.htm"), // TXT info
1, // auto rename the service when if needed
NULL, // no callback function
NULL // no application context
);
#endif /* defined(STACK_USE_TCP_MOBILE_APP_SERVER) */
mDNSMulticastFilterRegister();
#endif
#if defined(WF_CONSOLE)
WFConsoleInit();
#endif
// Now that all items are initialized, begin the co-operative
// multitasking loop. This infinite loop will continuously
// execute all stack-related tasks, as well as your own
// application's functions. Custom functions should be added
// at the end of this loop.
// Note that this is a "co-operative mult-tasking" mechanism
// where every task performs its tasks (whether all in one shot
// or part of it) and returns so that other tasks can do their
// job.
// If a task needs very long time to do its job, it must be broken
// down into smaller pieces so that other tasks can have CPU time.
while(1)
{
#if (MY_DEFAULT_NETWORK_TYPE == WF_SOFT_AP)
if (g_scan_done) {
if (g_prescan_waiting) {
putrsUART((ROM char*)"\n SoftAP prescan results ........ \r\n\n");
SCANCXT.displayIdx = 0;
while (IS_SCAN_STATE_DISPLAY(SCANCXT.scanState)) {
WFDisplayScanMgr();
}
putrsUART((ROM char*)"\r\n ");
#if defined(WF_CS_TRIS)
WF_Connect();
#endif
g_scan_done = 0;
g_prescan_waiting = 0;
}
}
#endif // (MY_DEFAULT_NETWORK_TYPE == WF_SOFT_AP)
#if defined(WF_PRE_SCAN_IN_ADHOC)
if(g_prescan_adhoc_done)
{
WFGetScanResults();
g_prescan_adhoc_done = 0;
}
#endif
#if defined (EZ_CONFIG_STORE)
// Hold button3 for 4 seconds to reset to defaults.
if (BUTTON3_IO == 0u) { // Button is pressed
if (ButtonPushStart == 0) //Just pressed
ButtonPushStart = TickGet();
else
if(TickGet() - ButtonPushStart > 4*TICK_SECOND)
RestoreWifiConfig();
}
else
{
ButtonPushStart = 0; //Button release reset the clock
}
if (AppConfig.saveSecurityInfo)
{
// set true by WF_ProcessEvent after connecting to a new network
// get the security info, and if required, push the PSK to EEPROM
if ((AppConfig.SecurityMode == WF_SECURITY_WPA_WITH_PASS_PHRASE) ||
(AppConfig.SecurityMode == WF_SECURITY_WPA2_WITH_PASS_PHRASE) ||
(AppConfig.SecurityMode == WF_SECURITY_WPA_AUTO_WITH_PASS_PHRASE))
{
// only need to save when doing passphrase
tWFCPElements profile;
UINT8 connState;
UINT8 connID;
WF_CMGetConnectionState(&connState, &connID);
WF_CPGetElements(connID, &profile);
memcpy((char*)AppConfig.SecurityKey, (char*)profile.securityKey, 32);
AppConfig.SecurityMode--; // the calc psk is exactly one below for each passphrase option
AppConfig.SecurityKeyLength = 32;
SaveAppConfig(&AppConfig);
}
AppConfig.saveSecurityInfo = FALSE;
}
#endif // EZ_CONFIG_STORE
#if defined (STACK_USE_EZ_CONFIG)
// Blink LED0 twice per sec when unconfigured, once per sec after config
if((TickGet() - t >= TICK_SECOND/(4ul - (CFGCXT.isWifiDoneConfigure*2ul))))
#else
// Blink LED0 (right most one) every second.
if(TickGet() - t >= TICK_SECOND/2ul)
#endif // STACK_USE_EZ_CONFIG
{
t = TickGet();
LED0_IO ^= 1;
}
// This task performs normal stack task including checking
// for incoming packet, type of packet and calling
// appropriate stack entity to process it.
StackTask();
// This tasks invokes each of the core stack application tasks
StackApplications();
#if defined(STACK_USE_ZEROCONF_LINK_LOCAL)
ZeroconfLLProcess();
#endif
#if defined(STACK_USE_ZEROCONF_MDNS_SD)
mDNSProcess();
// Use this function to exercise service update function
// HTTPUpdateRecord();
#endif
// Process application specific tasks here.
// For this demo app, this will include the Generic TCP
// client and servers, and the SNMP, Ping, and SNMP Trap
// demos. Following that, we will process any IO from
// the inputs on the board itself.
// Any custom modules or processing you need to do should
// go here.
#if defined(WF_CONSOLE)
WFConsoleProcess();
WFConsoleProcessEpilogue();
#endif
#if defined(STACK_USE_GENERIC_TCP_CLIENT_EXAMPLE)
GenericTCPClient();
#endif
#if defined(STACK_USE_GENERIC_TCP_SERVER_EXAMPLE)
GenericTCPServer();
#endif
#if defined(STACK_USE_TCP_MOBILE_APP_SERVER)
MobileTCPServer();
#endif
#if defined(STACK_USE_SMTP_CLIENT)
SMTPDemo();
#endif
#if defined(STACK_USE_ICMP_CLIENT)
PingDemo();
PingConsole();
#endif
#if defined(STACK_USE_SNMP_SERVER) && !defined(SNMP_TRAP_DISABLED)
//User should use one of the following SNMP demo
// This routine demonstrates V1 or V2 trap formats with one variable binding.
SNMPTrapDemo();
#if defined(SNMP_STACK_USE_V2_TRAP) || defined(SNMP_V1_V2_TRAP_WITH_SNMPV3)
//This routine provides V2 format notifications with multiple (3) variable bindings
//User should modify this routine to send v2 trap format notifications with the required varbinds.
//SNMPV2TrapDemo();
#endif
if(gSendTrapFlag)
SNMPSendTrap();
#endif
#if defined(STACK_USE_BERKELEY_API)
BerkeleyTCPClientDemo();
BerkeleyTCPServerDemo();
BerkeleyUDPClientDemo();
#endif
// If the local IP address has changed (ex: due to DHCP lease change)
// write the new IP address to the LCD display, UART, and Announce
// service
if(dwLastIP != AppConfig.MyIPAddr.Val)
{
dwLastIP = AppConfig.MyIPAddr.Val;
#if defined(STACK_USE_UART)
putrsUART((ROM char*)"\r\nNew IP Address: ");
#endif
DisplayIPValue(AppConfig.MyIPAddr);
#if defined(STACK_USE_UART)
putrsUART((ROM char*)"\r\n");
#endif
#if defined(STACK_USE_ANNOUNCE)
AnnounceIP();
#endif
#if defined(STACK_USE_ZEROCONF_MDNS_SD)
mDNSFillHostRecord();
#endif
}
}
}
int main(void)
#endif
{
static DWORD t = 0;
static DWORD dwLastIP = 0;
#if defined(WF_USE_POWER_SAVE_FUNCTIONS)
BOOL PsPollEnabled;
BOOL psConfDone = FALSE;
#endif
// Initialize application specific hardware
InitializeBoard();
#if defined(USE_LCD)
// Initialize and display the stack version on the LCD
LCDInit();
DelayMs(100);
strcpypgm2ram((char*)LCDText, "TCPStack " TCPIP_STACK_VERSION " "
" ");
LCDUpdate();
#endif
// Initialize stack-related hardware components that may be
// required by the UART configuration routines
TickInit();
#if defined(STACK_USE_MPFS2)
MPFSInit();
#endif
// Initialize Stack and application related NV variables into AppConfig.
InitAppConfig();
// Initiates board setup process if button is depressed
// on startup
if(BUTTON0_IO == 0u)
{
#if defined(EEPROM_CS_TRIS) || defined(SPIFLASH_CS_TRIS)
// Invalidate the EEPROM contents if BUTTON0 is held down for more than 4 seconds
DWORD StartTime = TickGet();
LED_PUT(0x00);
while(BUTTON0_IO == 0u)
{
if(TickGet() - StartTime > 4*TICK_SECOND)
{
#if defined(EEPROM_CS_TRIS)
XEEBeginWrite(0x0000);
XEEWrite(0xFF);
XEEWrite(0xFF);
XEEEndWrite();
#elif defined(SPIFLASH_CS_TRIS)
SPIFlashBeginWrite(0x0000);
SPIFlashWrite(0xFF);
SPIFlashWrite(0xFF);
#endif
#if defined(STACK_USE_UART)
putrsUART("\r\n\r\nBUTTON0 held for more than 4 seconds. Default settings restored.\r\n\r\n");
#endif
LED_PUT(0x0F);
while((LONG)(TickGet() - StartTime) <= (LONG)(9*TICK_SECOND/2));
LED_PUT(0x00);
while(BUTTON0_IO == 0u);
Reset();
break;
}
}
#endif
#if defined(STACK_USE_UART)
DoUARTConfig();
#endif
}
// Initialize core stack layers (MAC, ARP, TCP, UDP) and
// application modules (HTTP, SNMP, etc.)
StackInit();
#if defined(WF_CS_TRIS)
WF_Connect();
#endif
// Initialize any application-specific modules or functions/
// For this demo application, this only includes the
// UART 2 TCP Bridge
#if defined(STACK_USE_UART2TCP_BRIDGE)
UART2TCPBridgeInit();
#endif
#if defined(STACK_USE_ZEROCONF_LINK_LOCAL)
ZeroconfLLInitialize();
#endif
#if defined(STACK_USE_ZEROCONF_MDNS_SD)
mDNSInitialize(MY_DEFAULT_HOST_NAME);
mDNSServiceRegister(
(const char *) "DemoWebServer", // base name of the service
"_http._tcp.local", // type of the service
80, // TCP or UDP port, at which this service is available
((const BYTE *)"path=/index.htm"), // TXT info
1, // auto rename the service when if needed
NULL, // no callback function
NULL // no application context
);
mDNSMulticastFilterRegister();
#endif
// Now that all items are initialized, begin the co-operative
// multitasking loop. This infinite loop will continuously
// execute all stack-related tasks, as well as your own
// application's functions. Custom functions should be added
// at the end of this loop.
// Note that this is a "co-operative mult-tasking" mechanism
// where every task performs its tasks (whether all in one shot
// or part of it) and returns so that other tasks can do their
// job.
// If a task needs very long time to do its job, it must be broken
// down into smaller pieces so that other tasks can have CPU time.
while(1)
{
//while (1)
/*{
if(BUTTON0_IO == 0u && LED0_IO == 0)
{
LED0_IO =1;
}
if(BUTTON0_IO == 0u && LED0_IO ==1)
{
LED0_IO =0;
}
}*/
#if defined(WF_USE_POWER_SAVE_FUNCTIONS)
if (!psConfDone && WFisConnected()) {
PsPollEnabled = (MY_DEFAULT_PS_POLL == WF_ENABLED);
if (!PsPollEnabled) {
/* disable low power (PS-Poll) mode */
#if defined(STACK_USE_UART)
putrsUART("Disable PS-Poll\r\n");
#endif
WF_PsPollDisable();
} else {
/* Enable low power (PS-Poll) mode */
#if defined(STACK_USE_UART)
putrsUART("Enable PS-Poll\r\n");
#endif
WF_PsPollEnable(TRUE);
}
psConfDone = TRUE;
}
#endif
// Blink LED0 (right most one) every second.
// if(TickGet() - t >= TICK_SECOND/2ul)
// {
// t = TickGet();
// LED0_IO ^= 1;
// }
// This task performs normal stack task including checking
// for incoming packet, type of packet and calling
// appropriate stack entity to process it.
StackTask();
// This tasks invokes each of the core stack application tasks
StackApplications();
#if defined(STACK_USE_ZEROCONF_LINK_LOCAL)
ZeroconfLLProcess();
#endif
#if defined(STACK_USE_ZEROCONF_MDNS_SD)
mDNSProcess();
// Use this function to exercise service update function
// HTTPUpdateRecord();
#endif
// Process application specific tasks here.
// For this demo app, this will include the Generic TCP
// client and servers, and the SNMP, Ping, and SNMP Trap
// demos. Following that, we will process any IO from
// the inputs on the board itself.
// Any custom modules or processing you need to do should
// go here.
#if defined(STACK_USE_GENERIC_TCP_CLIENT_EXAMPLE)
GenericTCPClient();
#endif
#if defined(STACK_USE_GENERIC_TCP_SERVER_EXAMPLE)
GenericTCPServer();
#endif
#if defined(STACK_USE_SMTP_CLIENT)
SMTPDemo();
#endif
#if defined(STACK_USE_ICMP_CLIENT)
PingDemo();
#endif
#if defined(STACK_USE_SNMP_SERVER) && !defined(SNMP_TRAP_DISABLED)
//User should use one of the following SNMP demo
// This routine demonstrates V1 or V2 trap formats with one variable binding.
SNMPTrapDemo();
#if defined(SNMP_STACK_USE_V2_TRAP) || defined(SNMP_V1_V2_TRAP_WITH_SNMPV3)
//This routine provides V2 format notifications with multiple (3) variable bindings
//User should modify this routine to send v2 trap format notifications with the required varbinds.
//SNMPV2TrapDemo();
#endif
if(gSendTrapFlag)
SNMPSendTrap();
#endif
#if defined(STACK_USE_BERKELEY_API)
BerkeleyTCPClientDemo();
BerkeleyTCPServerDemo();
BerkeleyUDPClientDemo();
#endif
ProcessIO();
// If the local IP address has changed (ex: due to DHCP lease change)
// write the new IP address to the LCD display, UART, and Announce
// service
if(dwLastIP != AppConfig.MyIPAddr.Val)
{
dwLastIP = AppConfig.MyIPAddr.Val;
#if defined(STACK_USE_UART)
putrsUART((ROM char*)"\r\nNew IP Address: ");
#endif
DisplayIPValue(AppConfig.MyIPAddr);
#if defined(STACK_USE_UART)
putrsUART((ROM char*)"\r\n");
#endif
#if defined(STACK_USE_ANNOUNCE)
AnnounceIP();
#endif
#if defined(STACK_USE_ZEROCONF_MDNS_SD)
mDNSFillHostRecord();
#endif
}
}
}
//função principal
void main(void)
{
static TICK t = 0;
//inicializa todas as configuraçoes de hardware
InitializeBoard();
#if defined(USE_LCD)
//inicializa configs do LCD se acaso estiver habilitado
LCDInit();
DelayMs(100);
strcpypgm2ram((char*)LCDText, "APP TCPIP");
LCDUpdate();
#endif
//inicializa um tick de tempo usado para TICK,SPI,UAT
TickInit();
//inicializa MPSF para upload de paginas web se acaso estiver habilitado
#if defined(STACK_USE_MPFS) || defined(STACK_USE_MPFS2)
MPFSInit();
#endif
//inicializa variaveis da aplicação AppConfig (IP, MASCARA, GATWAY, ETC)
InitAppConfig();
//inicializa a layer da pilha TCPIP (MAC, ARP, TCP, UDP)
//e tambem as aplicaçoes habilitadas (HTTP, SNMP, SOCKET, ETC)
StackInit();
//inicializa UART 2 TCP Bridge
#if defined(STACK_USE_UART2TCP_BRIDGE)
UART2TCPBridgeInit();
#endif
//laço principal (nunca use delays, apenas maquinas de estado)
//todos os processos devem estar executando paralelamente
while(1)
{
//pisca o led para informar a pilha rodando
if(TickGet() - t >= TICK_SECOND/2ul)
{
t = TickGet();
LED0_IO ^= 1;
}
//processa coisas relacionadas ao hardware, leitura de pinos,etc.
ProcessIO();
//chama tarefas da pilha TCPIP
StackTask();
//chama tarefas das aplicaçoes habilitadas
StackApplications();
//exemplo de aplicação Cliente Socket
#if defined(STACK_USE_TCP_CLIENT)
ClientSocketTCP();
#endif
//exemplo de aplicação Servidor Socket
#if defined(STACK_USE_TCP_SERVER)
ServerSocketTCP();
#endif
}
}
int main(void)
#endif
{
static TICK t = 0;
TICK nt = 0; //TICK is DWORD, thus 32 bits
BYTE loopctr = 0; //ML Debugging
WORD lloopctr = 14; //ML Debugging
static DWORD dwLastIP = 0;
// Initialize interrupts and application specific hardware
InitializeBoard();
// Initialize and display message on the LCD
LCDInit();
DelayMs(100);
DisplayString (0,"Olimex"); //first arg is start position on 32 pos LCD
// Initialize Timer0, and low priority interrupts, used as clock.
TickInit();
// Initialize Stack and application related variables in AppConfig.
InitAppConfig();
// Initialize core stack layers (MAC, ARP, TCP, UDP) and
// application modules (HTTP, SNMP, etc.)
StackInit();
// Now that all items are initialized, begin the co-operative
// multitasking loop. This infinite loop will continuously
// execute all stack-related tasks, as well as your own
// application's functions. Custom functions should be added
// at the end of this loop.
// Note that this is a "co-operative multi-tasking" mechanism
// where every task performs its tasks (whether all in one shot
// or part of it) and returns so that other tasks can do their
// job.
// If a task needs very long time to do its job, it must be broken
// down into smaller pieces so that other tasks can have CPU time.
while(1)
{
// Blink LED0 (right most one) every second.
nt = TickGetDiv256();
if((nt - t) >= (DWORD)(TICK_SECOND/1024ul))
{
t = nt;
LED0_IO ^= 1;
ClrWdt(); //Clear the watchdog
}
// This task performs normal stack task including checking
// for incoming packet, type of packet and calling
// appropriate stack entity to process it.
StackTask();
// This tasks invokes each of the core stack application tasks
StackApplications();
// Process application specific tasks here.
// If the local IP address has changed (ex: due to DHCP lease change)
// write the new IP address to the LCD display, UART, and Announce
// service
if(dwLastIP != AppConfig.MyIPAddr.Val)
{
dwLastIP = AppConfig.MyIPAddr.Val;
#if defined(__SDCC__)
DisplayIPValue(dwLastIP); // must be a WORD: sdcc does not
// pass aggregates
#else
DisplayIPValue(AppConfig.MyIPAddr);
#endif
}
}//end of while(1)
}//end of main()
void main(void)
{
static DWORD currentTick = 0;
static DWORD bsdTick = 0;
static DWORD dwLastIP = 0;
UINT8 i;
// Initialize application specific hardware
BRD_init();
// Initialize stack-related hardware components that may be
// required by the UART configuration routines
TickInit();
#if defined(STACK_USE_MPFS2)
MPFSInit();
#endif
// Initialize Stack and application related NV variables into AppConfig.
InitAppConfig();
// Initialize core stack layers (MAC, ARP, TCP, UDP) and
// application modules (HTTP, SNMP, etc.)
StackInit();
#ifdef __MODBUS__
APP_init( );
UART_init( 62500 );
#endif
EnableInterrupts( );
/* for( i = 0; i < 26; i++ )
{
UART_write( 'A' + i );
UART_transmit();
}*/
// Now that all items are initialized, begin the co-operative
// multitasking loop. This infinite loop will continuously
// execute all stack-related tasks, as well as your own
// application's functions. Custom functions should be added
// at the end of this loop.
// Note that this is a "co-operative mult-tasking" mechanism
// where every task performs its tasks (whether all in one shot
// or part of it) and returns so that other tasks can do their
// job.
// If a task needs very lgong time to do its job, it must be broken
// down into smaller pieces so that other tasks can have CPU time.
while(1)
{
// Blink LED0 (right most one) every second.
if(TickGet() - currentTick >= TICK_SECOND/2ul)
{
currentTick = TickGet();
// COM_task( );
// LED0_IO ^= 1;
// TxData = TRUE;
}
// This task performs normal stack task including checking
// for incoming packet, type of packet and calling
// appropriate stack entity to process it.
StackTask();
// This tasks invokes each of the core stack application tasks
StackApplications();
// Process application specific tasks here.
// For this demo app, this will include the Generic TCP
// client and servers, and the SNMP, Ping, and SNMP Trap
// demos. Following that, we will process any IO from
// the inputs on the board itself.
// Any custom modules or processing you need to do should
// go here.
#if defined(STACK_USE_ICMP_CLIENT)
PingDemo();
#endif
#if defined(STACK_USE_BERKELEY_API)
// BerkeleyTCPClientDemo();
if(TickGet() - bsdTick >= TICK_SECOND)
{
bsdTick = currentTick;
BerkeleyTCPServerDemo();
}
//BerkeleyUDPClientDemo();
#endif
#ifdef __MODBUS__
eMBPoll( );
COM_task( );
#endif
}
}
int main(void)
{
// Initialize the device clock speed, ports and peripherals
InitPic();
// Initialize stack-related hardware components that may be
// required by the UART configuration routines
TickInit();
MPFSInit();
// Initialize Stack and application related NV variables into AppConfig.
InitAppConfig();
InitFocusers();
InitClient_Serial();
InitClient_HandControl();
InitClient_WiFi();
// Restore the defaults for the stack settings...
/*
XEEBeginWrite(0x0000);
XEEWrite(0xFF);
XEEWrite(0xFF);
XEEEndWrite();
*/
// Initialize core stack layers (MAC, ARP, TCP, UDP) and
// application modules (HTTP, SNMP, etc.)
StackInit();
// MAIN PROGRAM LOOP
while(1)
{
// 1. Perform necessary TCP/IP stack operations
// This task performs normal stack task including checking
// for incoming packets, type of packet and calling
// appropriate stack entity to process it.
StackTask();
// This tasks invokes each of the core stack application tasks
StackApplications();
// 2. Check if command received from serial port host
ReceiveSerialCmds();
// 3. Process WiFi HTTP operations
DoWiFiWork();
// 4. Check if command received from WiFi host
ReceiveWiFiCmds();
// 5. Check if command received from Wired Ethernet host
ReceiveEthernetCmds();
// 6. Check if command received from Hand Control Box
ReceiveSerialCmds_HC();
// 7. Process any command received for Focusers from any client...
ProcessReceivedCommands();
// 8. Perform Focuser Operations
// (i.e. Get current temp, Operate motion state machine, etc.)
DoFocuserOperations();
}
}
/*****************************************************************************
FUNCTION TCPIPTask
Main function to handle the TCPIP stack
RETURNS None
PARAMS None
*****************************************************************************/
void TCPIPTask()
{
WFConnection = WF_CUSTOM;
ConnectionProfileID = 0;
static DWORD dwLastIP = 0;
WFStatus = NOT_CONNECTED;
dwLastIP = 0;
// Function pointers for the callback function of the TCP/IP and WiFi stack
#if defined (FLYPORT)
FP[1] = cWFConnect;
FP[2] = cWFDisconnect;
FP[3] = cWFScan;
FP[5] = cWFPsPollDisable;
FP[6] = cWFPsPollEnable;
FP[7] = cWFScanList;
FP[10] = cWFStopConnecting;
#endif
#if defined (FLYPORTETH)
FP[1] = cETHRestart;
#endif
FP[16] = cTCPRxFlush;
FP[17] = cTCPpRead;
FP[18] = cTCPRemote;
FP[19] = cTCPServerDetach;
FP[20] = cTCPGenericOpen;
FP[21] = cTCPRead;
FP[22] = cTCPWrite;
FP[23] = cTCPGenericClose;
FP[24] = cTCPisConn;
FP[25] = cTCPRxLen;
#if defined(STACK_USE_SMTP_CLIENT)
FP[26] = cSMTPStart;
FP[27] = cSMTPSetServer;
FP[28] = cSMTPSetMsg;
FP[29] = cSMTPSend;
FP[30] = cSMTPBusy;
FP[31] = cSMTPStop;
FP[32] = cSMTPReport;
#endif
FP[ARP_RESOLVE] = cARPResolveMAC;
#if MAX_UDP_SOCKETS_FREERTOS>0
FP[35] = cUDPGenericOpen;
FP[36] = cUDPWrite;
FP[37] = cUDPGenericClose;
#endif
// Initialize stack-related hardware components that may be
// required by the UART configuration routines
// Initialization of tick only at the startup of the device
if (hFlyTask == NULL)
{
TickInit();
}
#if defined(STACK_USE_MPFS) || defined(STACK_USE_MPFS2)
MPFSInit();
#endif
// Initialize Stack and application related NV variables into AppConfig.
InitAppConfig();
// Initialize core stack layers (MAC, ARP, TCP, UDP) and application modules (HTTP, SNMP, etc.)
StackInit();
if (hFlyTask == NULL)
{
NETConf[0] = AppConfig;
NETConf[1] = AppConfig;
}
#if defined(WF_CS_TRIS)
if (WFStatus == CONNECTION_LOST)
WF_Connect(WFConnection);
#endif
#if defined(STACK_USE_ZEROCONF_LINK_LOCAL)
ZeroconfLLInitialize();
#endif
#if defined(STACK_USE_ZEROCONF_MDNS_SD)
mDNSInitialize(MY_DEFAULT_HOST_NAME);
mDNSServiceRegister(
(const char *) "DemoWebServer", // base name of the service
"_http._tcp.local", // type of the service
80, // TCP or UDP port, at which this service is available
((const BYTE *)"path=/index.htm"), // TXT info
1, // auto rename the service when if needed
NULL, // no callback function
NULL // no application context
);
mDNSMulticastFilterRegister();
#endif
// INITIALIZING UDP
#if MAX_UDP_SOCKETS_FREERTOS>0
#if defined (STACK_USE_UART)
UARTWrite(1, "Initializing UDP...\r\n");
#endif
UDPInit();
activeUdpSocket=0;
while (activeUdpSocket < MAX_UDP_SOCKETS_FREERTOS)
{
tmp_len[activeUdpSocket]=0;
if (activeUdpSocket == 0)
{
BUFFER_UDP_LEN[0] = BUFFER1_UDP_LEN;
udpBuffer[activeUdpSocket] = udpBuffer1;
udpSocket[0] = INVALID_UDP_SOCKET;
}
#if MAX_UDP_SOCKETS_FREERTOS>1
if (activeUdpSocket == 1)
{
BUFFER_UDP_LEN[1] = BUFFER2_UDP_LEN;
udpBuffer[activeUdpSocket] = udpBuffer2;
udpSocket[1] = INVALID_UDP_SOCKET;
}
#endif
#if MAX_UDP_SOCKETS_FREERTOS>2
if (activeUdpSocket == 2)
{
BUFFER_UDP_LEN[2] = BUFFER3_UDP_LEN;
udpBuffer[activeUdpSocket] = udpBuffer3;
udpSocket[2] = INVALID_UDP_SOCKET;
}
#endif
#if MAX_UDP_SOCKETS_FREERTOS>3
if (activeUdpSocket == 3)
{
BUFFER_UDP_LEN[3] = BUFFER4_UDP_LEN;
udpBuffer[activeUdpSocket] = udpBuffer4;
udpSocket[3] = INVALID_UDP_SOCKET;
}
#endif
p_udp_wifiram[activeUdpSocket] = udpBuffer[activeUdpSocket];
p_udp_data[activeUdpSocket] = udpBuffer[activeUdpSocket];
activeUdpSocket++;
}
#endif
if (hFlyTask == NULL)
{
// Creates the task dedicated to user code
xTaskCreate(FlyportTask,(signed char*) "FLY" , (configMINIMAL_STACK_SIZE * 4),
NULL, tskIDLE_PRIORITY + 1, &hFlyTask);
}
//-------------------------------------------------------------------------------------------
//| --- COOPERATIVE MULTITASKING LOOP --- |
//-------------------------------------------------------------------------------------------
while(1)
{
#if defined (FLYPORT)
if (WFStatus != TURNED_OFF)
{
// Check to verify the connection. If it's lost or failed, the device tries to reconnect
if ((WFStatus == CONNECTION_LOST) || (WFStatus == CONNECTION_FAILED))
WF_Connect(WFConnection);
#else
{
#endif
// This task performs normal stack task including checking
// for incoming packet, type of packet and calling
// appropriate stack entity to process it.
vTaskSuspendAll();
StackTask();
xTaskResumeAll();
#if defined(STACK_USE_HTTP_SERVER) || defined(STACK_USE_HTTP2_SERVER)
vTaskSuspendAll();
HTTPServer();
xTaskResumeAll();
#endif
// This tasks invokes each of the core stack application tasks
StackApplications();
#if defined(STACK_USE_ZEROCONF_LINK_LOCAL)
ZeroconfLLProcess();
#endif
#if defined(STACK_USE_ZEROCONF_MDNS_SD)
mDNSProcess();
// Use this function to exercise service update function
// HTTPUpdateRecord();
#endif
#if defined(STACK_USE_SNMP_SERVER) && !defined(SNMP_TRAP_DISABLED)
//User should use one of the following SNMP demo
// This routine demonstrates V1 or V2 trap formats with one variable binding.
SNMPTrapDemo();
#if defined(SNMP_STACK_USE_V2_TRAP)
//This routine provides V2 format notifications with multiple (3) variable bindings
//User should modify this routine to send v2 trap format notifications with the required varbinds.
//SNMPV2TrapDemo();
#endif
if(gSendTrapFlag)
SNMPSendTrap();
#endif
#if defined(STACK_USE_BERKELEY_API)
BerkeleyTCPClientDemo();
BerkeleyTCPServerDemo();
BerkeleyUDPClientDemo();
#endif
// Check on the queue to verify if other task have requested some stack function
xStatus = xQueueReceive(xQueue,&Cmd,0);
CmdCheck();
// If the local IP address has changed (ex: due to DHCP lease change)
// write the new IP address to the LCD display, UART, and Announce
// service
if(dwLastIP != AppConfig.MyIPAddr.Val)
{
dwLastIP = AppConfig.MyIPAddr.Val;
#if defined(STACK_USE_UART)
UARTWrite(1,"\r\nNew IP Address: ");
#endif
DisplayIPValue(AppConfig.MyIPAddr);
#if defined(STACK_USE_UART)
UARTWrite(1,"\r\n");
#endif
#if defined(STACK_USE_ANNOUNCE)
AnnounceIP();
#endif
#if defined(STACK_USE_ZEROCONF_MDNS_SD)
mDNSFillHostRecord();
#endif
}
} //end check turnoff
}
}
//
// Main application entry point.
//
int main(void)
{
static TICK t = 0;
static DWORD dwLastIP = 0;
// Initialize application specific hardware
InitializeBoard();
// Initialize stack-related hardware components that may be
// required by the UART configuration routines
TickInit();
MPFSInit();
// Initialize Stack and application related NV variables into AppConfig.
InitAppConfig();
// Initialize core stack layers (MAC, ARP, TCP, UDP) and
// application modules (HTTP, SNMP, etc.)
StackInit();
// Initialize any application-specific modules or functions/
// For this demo application, this only includes the
// UART 2 TCP Bridge
//************** PIC32-WEB ********************
//***** Additional initializations Start: *****
// 1. UART1
USART_Init(115200,(GetPeripheralClock()));
USART_Test_Menu_Begin();
// 2. Timer1
// configure Timer 1 using external clock(32768Hz), 1:1 prescale,
// period 0x8000, thus set interrupt on every 1sec
// Blink LED0 (right most one) with frequency 2Hz at every one Timer1 interrupt.
OpenTimer1(T1_ON | T1_SOURCE_EXT | T1_PS_1_1, 0x8000);
// set up the timer interrupt with a priority of 3
ConfigIntTimer1(T1_INT_ON | T1_INT_PRIOR_3);
//CloseTimer1(); // Switches off the Timer1
mPORTASetPinsDigitalOut(BIT_2); // Set RA2 like out -> LED1
// 3. Enable interrupts at the end of initialization
// enable multi-vector interrupts
INTEnableSystemMultiVectoredInt();
//***** Additional initializations End: *****
// Now that all items are initialized, begin the co-operative
// multitasking loop. This infinite loop will continuously
// execute all stack-related tasks, as well as your own
// application's functions. Custom functions should be added
// at the end of this loop.
// Note that this is a "co-operative mult-tasking" mechanism
// where every task performs its tasks (whether all in one shot
// or part of it) and returns so that other tasks can do their
// job.
// If a task needs very long time to do its job, it must be broken
// down into smaller pieces so that other tasks can have CPU time.
while(1){
// Run all enabled web demo applications:
// This task performs normal stack task including checking
// for incoming packet, type of packet and calling
// appropriate stack entity to process it.
StackTask();
// This tasks invokes each of the core stack application tasks
StackApplications();
// Process application specific tasks here.
// For this demo app, this will include the Generic TCP
// client and servers, and the SNMP, Ping, and SNMP Trap
// demos. Following that, we will process any IO from
// the inputs on the board itself.
// Any custom modules or processing you need to do should
// go here.
#if defined(STACK_USE_ICMP_CLIENT)
PingDemo();
#endif
#if defined(STACK_USE_SNMP_SERVER) && !defined(SNMP_TRAP_DISABLED)
SNMPTrapDemo();
if(gSendTrapFlag)
SNMPSendTrap();
#endif
#if defined(STACK_USE_BERKELEY_API)
BerkeleyTCPClientDemo();
BerkeleyTCPServerDemo();
BerkeleyUDPClientDemo();
#endif
ProcessIO();
// If the local IP address has changed (ex: due to DHCP lease change)
// write the new IP address to the LCD display, UART, and Announce
// service
if(dwLastIP != AppConfig.MyIPAddr.Val)
{
#if defined(STACK_USE_ANNOUNCE)
AnnounceIP();
#endif
}
}
}
//
// Main application entry point.
//
int main(void)
{
static DWORD t = 0;
// Initialize application specific hardware
InitializeBoard();
//Initialize the DB_UTILS IO channel
/* Must add "PIC32_STARTER_KIT" macro definition to the project
* build options for the C compiler for debug output to work. */
DBINIT();
// Display the introduction
DBPRINTF("Smart Outlet Started\n");
fprintf(stdout, "stdout up\n");
fprintf(stderr, "stderr up\n");
// Initialize stack-related hardware components that may be
// required by the UART configuration routines
TickInit();
#if defined(STACK_USE_MPFS) || defined(STACK_USE_MPFS2)
MPFSInit();
#endif
// Initialize Stack and application related NV variables into AppConfig.
InitAppConfig();
// Initialize core stack layers (MAC, ARP, TCP, UDP) and
// application modules (HTTP, SNMP, etc.)
StackInit();
// Initialize any application-specific modules or functions/
// SmartWall Init
/* Local Temp Vars */
unsigned int i = 0;
/* Setup Temporary Processor Storage Vars */
/* Chan Storage */
struct SWChannelEntry tmpChnEntries[MYSWCHAN];
memset(&tmpChnEntries, 0, sizeof(tmpChnEntries));
struct SWChannelData tmpChnData;
memset(&tmpChnData, 0, sizeof(tmpChnData));
union outletChanArg tmpChanArgs[MYSWCHAN];
memset(&tmpChanArgs, 0, sizeof(tmpChanArgs));
tmpChnData.data = tmpChnEntries;
/* Init chanData Buffer */
for(i = 0; i < MYSWCHAN; i++){
tmpChnData.data[i].chanValue = &(tmpChanArgs[i]);
}
struct SWChannelLimits limits;
limits.maxNumChan = MYSWCHAN;
limits.maxDataLength = sizeof(*tmpChanArgs);
/* Setup Processors */
struct SWDevProcessor processors[NUMOUTLETPROCESSORS];
memset(processors, 0, sizeof(processors));
processors[0].processorScope = SW_SCP_CHANNEL;
processors[0].data = &tmpChnData;
processors[0].dataLimits = &limits;
processors[0].decoder = (readSWBody)readSWChannelBody;
processors[0].handeler = (swDevHandeler)outletChnDevHandeler;
processors[0].encoder = (writeSWBody)writeSWChannelBody;
/* Setup State Vars */
struct outletDeviceState myState;
memset(&myState, 0, sizeof(myState));
outletChanState_t chState[MYSWCHAN];
memset(&chState, 0, sizeof(chState));
outletChanPower_t chPower[MYSWCHAN];
memset(&chPower, 0, sizeof(chPower));
struct SWDeviceInfo myDevice;
memset(&myDevice, 0, sizeof(myDevice));
myState.myDev = &myDevice;
myState.chState = chState;
myState.chPower = chPower;
enum SWReceiverState machineState = RST_SETUP;
/* Setup SW Vars */
struct SWDeviceInfo tgtDevice;
myState.myDev->devInfo.swAddr = MYSWADDRESS;
myState.myDev->devInfo.devTypes = MYSWTYPE;
myState.myDev->devInfo.numChan = MYSWCHAN;
myState.myDev->devInfo.version = SW_VERSION;
myState.myDev->devInfo.uid = MYSWUID;
myState.myDev->devInfo.groupID = MYSWGROUP;
/* My IP */
myState.myDev->devIP.sin_family = AF_INET;
myState.myDev->devIP.sin_port = LISTENPORT;
myState.myDev->devIP.sin_addr.s_addr = hton32(INADDR_ANY);
tgtDevice.devIP.sin_family = AF_INET;
tgtDevice.devIP.sin_port = SENDPORT;
tgtDevice.devIP.sin_addr.s_addr = hton32(INADDR_ANY);
// Now that all items are initialized, begin the co-operative
// multitasking loop. This infinite loop will continuously
// execute all stack-related tasks, as well as your own
// application's functions. Custom functions should be added
// at the end of this loop.
// Note that this is a "co-operative mult-tasking" mechanism
// where every task performs its tasks (whether all in one shot
// or part of it) and returns so that other tasks can do their
// job.
// If a task needs very long time to do its job, it must be broken
// down into smaller pieces so that other tasks can have CPU time.
while(1)
{
// Blink LED0 (right most one) every second.
if(TickGet() - t >= TICK_SECOND/2ul)
{
t = TickGet();
LED0_IO ^= 1;
}
// This task performs normal stack task including checking
// for incoming packet, type of packet and calling
// appropriate stack entity to process it.
StackTask();
// This tasks invokes each of the core stack application tasks
StackApplications();
// Process application specific tasks here.
// Any custom modules or processing you need to do should
// go here.
machineState = swReceiverStateMachine(machineState,
myState.myDev, &tgtDevice,
&myState,
processors, NUMOUTLETPROCESSORS);
updateDeviceState(&myState);
}
}
// ************************************************************
// Main application entry point.
// ************************************************************
int main(void)
{
static DWORD t = 0;
static DWORD dwLastIP = 0;
#if defined (EZ_CONFIG_STORE)
static DWORD ButtonPushStart = 0;
#endif
UINT8 channelList[] = MY_DEFAULT_CHANNEL_LIST_PRESCAN; // WF_PRESCAN
tWFScanResult bssDesc;
#if 0
INT8 TxPower; // Needed to change MRF24WG transmit power.
#endif
// Initialize application specific hardware
InitializeBoard();
// Initialize TCP/IP stack timer
TickInit(); // Timer 3 interrupt for refreshing motor status inside here
demo_TickInit();
#if defined(STACK_USE_MPFS2)
// Initialize the MPFS File System
// Generate a WifiGDemoMPFSImg.c file using the MPFS utility (refer to Convert WebPages to MPFS.bat)
// that gets compiled into source code and programmed into the flash of the uP.
MPFSInit();
#endif
// Initialize Stack and application related NV variables into AppConfig.
InitAppConfig();
// Initialize core stack layers (MAC, ARP, TCP, UDP) and
// application modules (HTTP, SNMP, etc.)
StackInit();
Exosite_Init("microchip","dv102412",IF_WIFI, 0);
#if 0
// Below is used to change MRF24WG transmit power.
// This has been verified to be functional (Jan 2013)
if (AppConfig.networkType == WF_SOFT_AP)
{
WF_TxPowerGetMax(&TxPower);
WF_TxPowerSetMax(TxPower);
}
#endif
// Run Self Test if SW0 pressed on startup
if(SW0_IO == 1)
SelfTest();
#ifdef STACK_USE_TELNET_SERVER
// Initialize Telnet and
// Put Remote client in Remote Character Echo Mode
TelnetInit();
putc(0xff, stdout); // IAC = Interpret as Command
putc(0xfe, stdout); // Type of Operation = DONT
putc(0x22, stdout); // Option = linemode
putc(0xff, stdout); // IAC = Interpret as Command
putc(0xfb, stdout); // Type of Operation = DO
putc(0x01, stdout); // Option = echo
#endif
#if defined ( EZ_CONFIG_SCAN )
// Initialize WiFi Scan State Machine NV variables
WFInitScan();
#endif
// WF_PRESCAN: Pre-scan before starting up as SoftAP mode
WF_CASetScanType(MY_DEFAULT_SCAN_TYPE);
WF_CASetChannelList(channelList, sizeof(channelList));
if (WFStartScan() == WF_SUCCESS) {
SCAN_SET_DISPLAY(SCANCXT.scanState);
SCANCXT.displayIdx = 0;
}
// Needed to trigger g_scan_done
WFRetrieveScanResult(0, &bssDesc);
#if defined(STACK_USE_ZEROCONF_LINK_LOCAL)
// Initialize Zeroconf Link-Local state-machine, regardless of network type.
ZeroconfLLInitialize();
#endif
#if defined(STACK_USE_ZEROCONF_MDNS_SD)
// Initialize DNS Host-Name from TCPIPConfig.h, regardless of network type.
mDNSInitialize(MY_DEFAULT_HOST_NAME);
mDNSServiceRegister(
// (const char *) AppConfig.NetBIOSName, // base name of the service. Ensure uniformity with CheckHibernate().
(const char *) "DemoWebServer", // base name of the service. Ensure uniformity with CheckHibernate().
"_http._tcp.local", // type of the service
80, // TCP or UDP port, at which this service is available
((const BYTE *)"path=/index.htm"), // TXT info
1, // auto rename the service when if needed
NULL, // no callback function
NULL // no application context
);
mDNSMulticastFilterRegister();
#endif
#if defined(WF_CONSOLE)
// Initialize the WiFi Console App
WFConsoleInit();
#endif
// Now that all items are initialized, begin the co-operative
// multitasking loop. This infinite loop will continuously
// execute all stack-related tasks, as well as your own
// application's functions. Custom functions should be added
// at the end of this loop.
// Note that this is a "co-operative mult-tasking" mechanism
// where every task performs its tasks (whether all in one shot
// or part of it) and returns so that other tasks can do their
// job.
// If a task needs very long time to do its job, it must be broken
// down into smaller pieces so that other tasks can have CPU time.
#ifndef PERIOD
#define PERIOD 3120 // set 3120 for get to timer interrupt every 20ms, 40MHz PBUS, div by 256
#endif
OpenTimer3(T3_ON | T3_SOURCE_INT | T3_PS_1_256, PERIOD);
while(1)
{
if (AppConfig.networkType == WF_SOFT_AP) {
if (g_scan_done) {
if (g_prescan_waiting) {
SCANCXT.displayIdx = 0;
while (IS_SCAN_STATE_DISPLAY(SCANCXT.scanState)) {
WFDisplayScanMgr();
}
#if defined(WF_CS_TRIS)
WF_Connect();
#endif
g_scan_done = 0;
g_prescan_waiting = 0;
}
}
}
#if defined (EZ_CONFIG_STORE)
// Hold SW0 for 4 seconds to reset to defaults.
if (SW0_IO == 1u) { // Button is pressed
button_state = 1;
if (ButtonPushStart == 0) //Just pressed
ButtonPushStart = TickGet();
else
if(TickGet() - ButtonPushStart > 4*TICK_SECOND)
RestoreWifiConfig();
}
else
{
ButtonPushStart = 0; //Button release reset the clock
}
if (AppConfig.saveSecurityInfo)
{
// set true by WF_ProcessEvent after connecting to a new network
// get the security info, and if required, push the PSK to EEPROM
if ((AppConfig.SecurityMode == WF_SECURITY_WPA_WITH_PASS_PHRASE) ||
(AppConfig.SecurityMode == WF_SECURITY_WPA2_WITH_PASS_PHRASE) ||
(AppConfig.SecurityMode == WF_SECURITY_WPA_AUTO_WITH_PASS_PHRASE))
{
// only need to save when doing passphrase
tWFCPElements profile;
UINT8 connState;
UINT8 connID;
WF_CMGetConnectionState(&connState, &connID);
WF_CPGetElements(connID, &profile);
memcpy((char*)AppConfig.SecurityKey, (char*)profile.securityKey, 32);
AppConfig.SecurityMode--; // the calc psk is exactly one below for each passphrase option
AppConfig.SecurityKeyLength = 32;
SaveAppConfig(&AppConfig);
}
AppConfig.saveSecurityInfo = FALSE;
}
#endif // EZ_CONFIG_STORE
// Blink LED0 twice per sec when unconfigured, once per sec after config
if((TickGet() - t >= TICK_SECOND/(4ul - (CFGCXT.isWifiDoneConfigure*3ul))))
{
t = TickGet();
LED0_INV();
}
// This task performs normal stack task including checking
// for incoming packet, type of packet and calling
// appropriate stack entity to process it.
StackTask();
// This task invokes each of the core stack application tasks
if (cloud_mode == 0)
StackApplications();
// Enable WF_USE_POWER_SAVE_FUNCTIONS
WiFiTask();
#if defined(STACK_USE_ZEROCONF_LINK_LOCAL)
ZeroconfLLProcess();
#endif
#if defined(STACK_USE_ZEROCONF_MDNS_SD)
mDNSProcess();
#endif
Exosite_Demo();
// Process application specific tasks here.
// Any custom modules or processing you need to do should
// go here.
#if defined(WF_CONSOLE)
WFConsoleProcess();
WFConsoleProcessEpilogue();
#endif
// If the local IP address has changed (ex: due to DHCP lease change)
// write the new IP address to the LCD display, UART, and Announce
// service
if(dwLastIP != AppConfig.MyIPAddr.Val)
{
dwLastIP = AppConfig.MyIPAddr.Val;
DisplayIPValue(AppConfig.MyIPAddr);
#if defined(STACK_USE_ANNOUNCE)
AnnounceIP();
#endif
#if defined(STACK_USE_ZEROCONF_MDNS_SD)
mDNSFillHostRecord();
#endif
}
}
}
int main(void)
#endif
{
BYTE i;
static DWORD t = 0;
static DWORD dwLastIP = 0;
static UINT8 updateDisplay = 0;
#if defined (EZ_CONFIG_STORE)
static DWORD ButtonPushStart = 0;
#endif
#if (MY_DEFAULT_NETWORK_TYPE == WF_SOFT_AP)
UINT8 channelList[] = MY_DEFAULT_CHANNEL_LIST_PRESCAN; // WF_PRESCAN
tWFScanResult bssDesc;
#endif
// Initialize application specific hardware
InitializeBoard();
// Initiates board setup process if button is depressed
// on startup
if (BUTTON1_IO == 0u) {
while (BUTTON1_IO == 0);
SelfTestMode();
}
//#if defined(USE_LCD)
/*******************************************************************/
// Initialize the LCD
/*******************************************************************/
ConfigureLCD_SPI();
LCDInit();
/*******************************************************************/
// Display Start-up Splash Screen
/*******************************************************************/
LCDBacklightON();
LEDS_ON();
LCDErase();
sprintf((char *) LCDText, (char*) " MiWi - WiFi ");
sprintf((char *) &(LCDText[16]), (char*) " Gateway Demo");
LCDUpdate();
/*******************************************************************/
// Initialize the MiWi Protocol Stack. The only input parameter indicates
// if previous network configuration should be restored.
/*******************************************************************/
MiApp_ProtocolInit(FALSE);
/*******************************************************************/
// Set Device Communication Channel
/*******************************************************************/
if (MiApp_SetChannel(myChannel) == FALSE) {
LCDDisplay((char *) "ERROR: Unable to Set Channel..", 0, TRUE);
while (1);
}
/*******************************************************************/
// Set the connection mode. The possible connection modes are:
// ENABLE_ALL_CONN: Enable all kinds of connection
// ENABLE_PREV_CONN: Only allow connection already exists in
// connection table
// ENABL_ACTIVE_SCAN_RSP: Allow response to Active scan
// DISABLE_ALL_CONN: Disable all connections.
/*******************************************************************/
MiApp_ConnectionMode(ENABLE_ALL_CONN);
/*******************************************************************/
// Function MiApp_EstablishConnection try to establish a new
// connection with peer device.
// The first parameter is the index to the active scan result,
// which is acquired by discovery process (active scan). If
// the value of the index is 0xFF, try to establish a
// connection with any peer.
// The second parameter is the mode to establish connection,
// either direct or indirect. Direct mode means connection
// within the radio range; indirect mode means connection
// may or may not in the radio range.
/*******************************************************************/
i = MiApp_EstablishConnection(0xFF, CONN_MODE_DIRECT);
/*******************************************************************/
// Display current opertion on LCD of demo board, if applicable
/*******************************************************************/
if (i != 0xFF) {
; // Connected Peer on Channel
} else {
/*******************************************************************/
// If no network can be found and join, we need to start a new
// network by calling function MiApp_StartConnection
//
// The first parameter is the mode of start connection. There are
// two valid connection modes:
// - START_CONN_DIRECT start the connection on current
// channel
// - START_CONN_ENERGY_SCN perform an energy scan first,
// before starting the connection on
// the channel with least noise
// - START_CONN_CS_SCN perform a carrier sense scan
// first, before starting the
// connection on the channel with
// least carrier sense noise. Not
// supported for current radios
//
// The second parameter is the scan duration, which has the same
// definition in Energy Scan. 10 is roughly 1 second. 9 is a
// half second and 11 is 2 seconds. Maximum scan duration is
// 14, or roughly 16 seconds.
//
// The third parameter is the channel map. Bit 0 of the
// double word parameter represents channel 0. For the 2.4GHz
// frequency band, all possible channels are channel 11 to
// channel 26. As the result, the bit map is 0x07FFF800. Stack
// will filter out all invalid channels, so the application
// only needs to pay attention to the channels that are not
// preferred.
/*******************************************************************/
MiApp_StartConnection(START_CONN_DIRECT, 10, 0);
}
// Turn OFF LCD after setting up MiWi Connection
LCDBacklightOFF();
// Initialize stack-related hardware components that may be
// required by the UART configuration routines
TickInit();
#if defined(STACK_USE_MPFS2)
MPFSInit();
#endif
// Initialize Stack and application related NV variables into AppConfig.
InitAppConfig();
dwLastIP = AppConfig.MyIPAddr.Val;
// Initialize core stack layers (MAC, ARP, TCP, UDP) and
// application modules (HTTP, SNMP, etc.)
StackInit();
#if defined ( EZ_CONFIG_SCAN )
WFInitScan();
#endif
#if (MY_DEFAULT_NETWORK_TYPE == WF_SOFT_AP)
// WF_PRESCAN: Pre-scan before starting up as SoftAP mode
WF_CASetScanType(MY_DEFAULT_SCAN_TYPE);
WF_CASetChannelList(channelList, sizeof (channelList));
if (WFStartScan() == WF_SUCCESS) {
SCAN_SET_DISPLAY(SCANCXT.scanState);
SCANCXT.displayIdx = 0;
//putsUART("main: Prescan WFStartScan() success ................. \r\n");
}
// Needed to trigger g_scan_done
WFRetrieveScanResult(0, &bssDesc);
#else
#if defined(WF_CS_TRIS)
WF_Connect();
#endif // defined(WF_CS_TRIS)
#endif // (MY_DEFAULT_NETWORK_TYPE == WF_SOFT_AP)
// Initialize any application-specific modules or functions/
// For this demo application, this only includes the
// UART 2 TCP Bridge
#if defined(STACK_USE_UART2TCP_BRIDGE)
UART2TCPBridgeInit();
#endif
#if defined(STACK_USE_ZEROCONF_LINK_LOCAL)
ZeroconfLLInitialize();
#endif
#if defined(STACK_USE_ZEROCONF_MDNS_SD)
mDNSInitialize(MY_DEFAULT_HOST_NAME);
mDNSServiceRegister(
(const char *) AppConfig.NetBIOSName, // base name of the service
"_http._tcp.local", // type of the service
80, // TCP or UDP port, at which this service is available
((const BYTE *) "path=/index.htm"), // TXT info
1, // auto rename the service when if needed
NULL, // no callback function
NULL // no application context
);
mDNSMulticastFilterRegister();
#endif
#if defined(WF_CONSOLE)
WFConsoleInit();
#endif
// Now that all items are initialized, begin the co-operative
// multitasking loop. This infinite loop will continuously
// execute all stack-related tasks, as well as your own
// application's functions. Custom functions should be added
// at the end of this loop.
// Note that this is a "co-operative mult-tasking" mechanism
// where every task performs its tasks (whether all in one shot
// or part of it) and returns so that other tasks can do their
// job.
// If a task needs very long time to do its job, it must be broken
// down into smaller pieces so that other tasks can have CPU time.
LEDS_OFF();
while (1) {
/*******************************************************************/
// Check Button Events
/*******************************************************************/
if (BUTTON1_IO == 0u) {
while (BUTTON1_IO == 0);
LCDErase();
sprintf((char *) LCDText, (char*) "Erase Room Info?");
sprintf((char *) &(LCDText[16]), (char*) "SW0:Yes SW2:No");
LCDUpdate();
while (1) {
if (BUTTON1_IO == 0u) {
while (BUTTON1_IO == 0);
LCDDisplay((char *) "STATUS: Erasing...", 0, TRUE);
EraseRoomInfo();
DisplaySSID();
break;
} else if (BUTTON2_IO == 0u) {
while (BUTTON2_IO == 0);
DisplaySSID();
break;
}
}
}
// Blink LED0 twice per sec when unconfigured, once per sec after config
if ((TickGet() - t >= TICK_SECOND / (4ul - (CFGCXT.isWifiDoneConfigure * 2ul)))) {
t = TickGet();
LED0_INV();
}
if(CFGCXT.isWifiNeedToConfigure) updateDisplay = 1;
#if (MY_DEFAULT_NETWORK_TYPE == WF_SOFT_AP)
if (g_scan_done) {
if (g_prescan_waiting) {
SCANCXT.displayIdx = 0;
while (IS_SCAN_STATE_DISPLAY(SCANCXT.scanState)) {
WFDisplayScanMgr();
}
#if defined(WF_CS_TRIS)
WF_Connect();
#endif
DisplaySSID();
g_scan_done = 0;
g_prescan_waiting = 0;
}
}
#endif // (MY_DEFAULT_NETWORK_TYPE == WF_SOFT_AP)
// This task performs normal stack task including checking
// for incoming packet, type of packet and calling
// appropriate stack entity to process it.
StackTask();
WiFiTask();
// This tasks invokes each of the core stack application tasks
StackApplications();
#if defined(STACK_USE_ZEROCONF_LINK_LOCAL)
ZeroconfLLProcess();
#endif
#if defined(STACK_USE_ZEROCONF_MDNS_SD)
mDNSProcess();
// Use this function to exercise service update function
// HTTPUpdateRecord();
#endif
// Process application specific tasks here.
// For this demo app, this will include the Generic TCP
// client and servers, and the SNMP, Ping, and SNMP Trap
// demos. Following that, we will process any IO from
// the inputs on the board itself.
// Any custom modules or processing you need to do should
// go here.
#if defined(WF_CONSOLE)
//WFConsoleProcess();
// #if !defined(STACK_USE_EZ_CONFIG)
// IperfAppCall();
// #endif
//WFConsoleProcessEpilogue();
wait_console_input:
#endif
#if defined(STACK_USE_GENERIC_TCP_CLIENT_EXAMPLE)
GenericTCPClient();
#endif
#if defined(STACK_USE_GENERIC_TCP_SERVER_EXAMPLE)
GenericTCPServer();
#endif
#if defined(STACK_USE_SMTP_CLIENT)
SMTPDemo();
#endif
#if defined(STACK_USE_ICMP_CLIENT)
PingDemo();
//PingConsole();
#endif
#if defined(STACK_USE_SNMP_SERVER) && !defined(SNMP_TRAP_DISABLED)
//User should use one of the following SNMP demo
// This routine demonstrates V1 or V2 trap formats with one variable binding.
SNMPTrapDemo();
#if defined(SNMP_STACK_USE_V2_TRAP) || defined(SNMP_V1_V2_TRAP_WITH_SNMPV3)
//This routine provides V2 format notifications with multiple (3) variable bindings
//User should modify this routine to send v2 trap format notifications with the required varbinds.
//SNMPV2TrapDemo();
#endif
if (gSendTrapFlag)
SNMPSendTrap();
#endif
#if defined ( WF_CONSOLE ) && defined ( EZ_CONFIG_SCAN )
WFDisplayScanMgr();
#endif
#if defined(STACK_USE_BERKELEY_API)
BerkeleyTCPClientDemo();
BerkeleyTCPServerDemo();
BerkeleyUDPClientDemo();
#endif
if((updateDisplay && CFGCXT.isWifiDoneConfigure) || (dwLastIP != AppConfig.MyIPAddr.Val))
{
if(dwLastIP != AppConfig.MyIPAddr.Val)
dwLastIP = AppConfig.MyIPAddr.Val;
if(updateDisplay && CFGCXT.isWifiDoneConfigure)
updateDisplay = 0;
#if defined(STACK_USE_ANNOUNCE)
AnnounceIP();
#endif
#if defined(STACK_USE_ZEROCONF_MDNS_SD)
mDNSFillHostRecord();
#endif
DisplaySSID();
}
}
}
int main(void)
#endif
{
unsigned char counter = 0;
static DWORD Ping_Start_Time = 0;
static unsigned char Ping_Counter = 0;
static DWORD t = 0;
static DWORD dwLastIP = 0;
LED0_TRIS = 0;
LED0_IO = 1;
Delay10KTCYx(0);
// Initialize application specific hardware
InitializeBoard();
#ifdef APP_USE_USB
InitializeUSB();
#if defined(USB_INTERRUPT)
USBDeviceAttach();
#endif
#endif
#if defined(USE_LCD)
// Initialize and display the stack version on the LCD
LCDInit();
DelayMs(100);
strcpypgm2ram((char*)LCDText, "TCPStack " VERSION " "
" ");
LCDUpdate();
#endif
// Initialize stack-related hardware components that may be
// required by the UART configuration routines
TickInit();
#if defined(STACK_USE_MPFS) || defined(STACK_USE_MPFS2)
MPFSInit();
#endif
// Initialize Stack and application related NV variables into AppConfig.
InitAppConfig();
// Initiates board setup process if button is depressed
// on startup
if(BUTTON0_IO == 0u)
{
#if defined(EEPROM_CS_TRIS) || defined(SPIFLASH_CS_TRIS)
// Invalidate the EEPROM contents if BUTTON0 is held down for more than 4 seconds
DWORD StartTime = TickGet();
LED_PUT(0x00);
#ifdef TRANSCEIVER_BOARD
#elif defined( SINGLEPHASEMETER_MCU1 )
while(BUTTON0_IO == 0u)
{
if(TickGet() - StartTime > 4*TICK_SECOND)
{
#if defined(EEPROM_CS_TRIS)
XEEBeginWrite(0x0000);
XEEWrite(0xFF);
XEEEndWrite();
#elif defined(SPIFLASH_CS_TRIS)
SPIFlashBeginWrite(0x0000);
SPIFlashWrite(0xFF);
#endif
#if defined(STACK_USE_UART)
putrsUART("\r\n\r\nBUTTON0 held for more than 4 seconds. Default settings restored.\r\n\r\n");
#endif
LED_PUT(0x0F);
while((LONG)(TickGet() - StartTime) <= (LONG)(9*TICK_SECOND/2));
LED_PUT(0x00);
while(BUTTON0_IO == 0u);
Reset();
break;
}
}
#else
#error "No board defined."
#endif
#endif
#if defined(STACK_USE_UART)
DoUARTConfig();
#endif
}
// Initialize core stack layers (MAC, ARP, TCP, UDP) and
// application modules (HTTP, SNMP, etc.)
StackInit();
// Initialize any application-specific modules or functions/
// For this demo application, this only includes the
// UART 2 TCP Bridge
#if defined(STACK_USE_UART2TCP_BRIDGE)
UART2TCPBridgeInit();
#endif
#ifdef SINGLEPHASEMETER_MCU1
MCUOpen();
#endif
#ifdef APP_USE_ZIGBEE
ZigbeeOpen();
#else
//#error no zigbee.
#endif
#ifdef APP_USE_RGB
OpenRGB();
#endif
// ROUTER CODES
#ifdef APP_USE_ROUTER_CODES
{
}
#endif
// END
// Now that all items are initialized, begin the co-operative
// multitasking loop. This infinite loop will continuously
// execute all stack-related tasks, as well as your own
// application's functions. Custom functions should be added
// at the end of this loop.
// Note that this is a "co-operative mult-tasking" mechanism
// where every task performs its tasks (whether all in one shot
// or part of it) and returns so that other tasks can do their
// job.
// If a task needs very long time to do its job, it must be broken
// down into smaller pieces so that other tasks can have CPU time.
while(1)
{
#ifdef SINGLEPHASEMETER_MCU1
MCUTasks();
#endif
#ifdef APP_USE_RGB
RGBTasks();
#endif
/**********************************************/
/**** Handle USB ******************************/
/**********************************************/
#if defined(USB_POLLING)
// Check bus status and service USB interrupts.
USBDeviceTasks(); // Interrupt or polling method. If using polling, must call
// this function periodically. This function will take care
// of processing and responding to SETUP transactions
// (such as during the enumeration process when you first
// plug in). USB hosts require that USB devices should accept
// and process SETUP packets in a timely fashion. Therefore,
// when using polling, this function should be called
// frequently (such as once about every 100 microseconds) at any
// time that a SETUP packet might reasonably be expected to
// be sent by the host to your device. In most cases, the
// USBDeviceTasks() function does not take very long to
// execute (~50 instruction cycles) before it returns.
#endif
// Application-specific tasks.
// Application related code may be added here, or in the ProcessIO() function.
ProcessUSBIO();
/**********************************************/
/**** Handle Zigbee ******************************/
/**********************************************/
#ifdef APP_USE_ZIGBEE
ZigbeeTasks();
{
if( counter++ > 200 )
{
char s[16] = {0x10, 0x01, 0, 0, 0, 0, 0, 0, 0xff, 0xfe, 0xff, 0xfe, 0, 0, 'A', '4'}; // , 0x64};
ZigbeeAPISendString(16, s);
counter = 0;
}
}
#endif
// Main program loop.
// Set up ping and node statuses. A ping is sent every 4 mins and a check is done every minute.
// Nodes that have not pinged within 5 min frame will be delisted as in the network.
if( Ping_Start_Time != 0 && (TickGet() - Ping_Start_Time) > (TICK_MINUTE) )
{
// Check nodes that have not sent their ping within the past 5 minutes.
{}
// Send out a ping if 4 minutes have lapsed.
if( Ping_Counter++ >= 4 )
{}
}
Ping_Start_Time = TickGet();
// Blink LED0 (right most one) every second.
if(TickGet() - t >= TICK_SECOND/2ul)
{
t = TickGet();
LED0_IO ^= 1;
}
// This task performs normal stack task including checking
// for incoming packet, type of packet and calling
// appropriate stack entity to process it.
StackTask();
// This tasks invokes each of the core stack application tasks
StackApplications();
// Process application specific tasks here.
// For this demo app, this will include the Generic TCP
// client and servers, and the SNMP, Ping, and SNMP Trap
// demos. Following that, we will process any IO from
// the inputs on the board itself.
// Any custom modules or processing you need to do should
// go here.
#if defined(STACK_USE_GENERIC_TCP_CLIENT_EXAMPLE)
GenericTCPClient();
#endif
#if defined(STACK_USE_GENERIC_TCP_SERVER_EXAMPLE)
GenericTCPServer();
#endif
#if defined(STACK_USE_SMTP_CLIENT)
SMTPDemo();
#endif
#if defined(STACK_USE_ICMP_CLIENT)
PingDemo();
#endif
#if defined(STACK_USE_SNMP_SERVER) && !defined(SNMP_TRAP_DISABLED)
SNMPTrapDemo();
if(gSendTrapFlag)
SNMPSendTrap();
#endif
#if defined(STACK_USE_BERKELEY_API)
BerkeleyTCPClientDemo();
BerkeleyTCPServerDemo();
BerkeleyUDPClientDemo();
#endif
#ifdef APP_USE_RGB
RGBTasks();
#endif
//ProcessIO();
// If the local IP address has changed (ex: due to DHCP lease change)
// write the new IP address to the LCD display, UART, and Announce
// service
if(dwLastIP != AppConfig.MyIPAddr.Val)
{
dwLastIP = AppConfig.MyIPAddr.Val;
#if defined(STACK_USE_UART)
putrsUART((ROM char*)"\r\nNew IP Address: ");
#endif
DisplayIPValue(AppConfig.MyIPAddr);
#if defined(STACK_USE_UART)
putrsUART((ROM char*)"\r\n");
#endif
#if defined(STACK_USE_ANNOUNCE)
AnnounceIP();
#endif
}
}
}