int main(void){
Output_Init();
// ST7735_XYplotInit("Temp", 0, 100, 0, 100);
PLL_Init(Bus80MHz); // 80 MHz
SYSCTL_RCGCGPIO_R |= 0x20; // activate port F
ADC0_InitSWTriggerSeq3_Ch9(); // allow time to finish activating
Timer0A_Init100HzInt(); // set up Timer0A for 100 Hz interrupts
GPIO_PORTF_DIR_R |= 0x06; // make PF2, PF1 out (built-in LED)
GPIO_PORTF_AFSEL_R &= ~0x06; // disable alt funct on PF2, PF1
GPIO_PORTF_DEN_R |= 0x06; // enable digital I/O on PF2, PF1
// configure PF2 as GPIO
GPIO_PORTF_PCTL_R = (GPIO_PORTF_PCTL_R&0xFFFFF00F)+0x00000000;
GPIO_PORTF_AMSEL_R = 0; // disable analog functionality on PF
PF2 = 0; // turn off LED
EnableInterrupts();
ST7735_SetCursor(6,0);
printf("C");
ST7735_SetCursor(13,0);
printf("ADC");
while(1){
PF1 ^= 0x02; // toggles when running in main
temperature = adcToTemp(ADCvalue);
ST7735_SetCursor(0,0);
ST7735_sDecOut2(temperature);
ST7735_SetCursor(9,0);
ST7735_OutUDec(ADCvalue);
}
}
int main(void){
PLL_Init(Bus80MHz); // 80 MHz
DisableInterrupts();
//ADC0_InitSWTriggerSeq3_Ch9(); // allow time to finish activating
Timer0A_Init100HzInt(); // set up Timer0A for 100 Hz interrupts
Timer1_Init();
Display_Init(); //initialize display
Timer2_Init1Hz();
PortF_Init(); //initialize portf with onboard switches
PortE_Init(); // initialize port e as breadboard switches.
EnableInterrupts();
while(1){
}
}
int main(void){
PLL_Init(Bus80MHz); // 80 MHz
SYSCTL_RCGCGPIO_R |= 0x20; // activate port F
ADC0_InitSWTriggerSeq3_Ch9(); // allow time to finish activating
Timer0A_Init100HzInt(); // set up Timer0A for 100 Hz interrupts
Timer1_Init();
//Timer2_Init(); //Enable this for part D.
GPIO_PORTF_DIR_R |= 0x06; // make PF2, PF1 out (built-in LED)
GPIO_PORTF_AFSEL_R &= ~0x06; // disable alt funct on PF2, PF1
GPIO_PORTF_DEN_R |= 0x06; // enable digital I/O on PF2, PF1
// configure PF2 as GPIO
GPIO_PORTF_PCTL_R = (GPIO_PORTF_PCTL_R&0xFFFFF00F)+0x00000000;
GPIO_PORTF_AMSEL_R = 0; // disable analog functionality on PF
PF2 = 0; // turn off LED
EnableInterrupts();
while(1){
PF1 ^= 0x02; // toggles when running in main
//GPIO_PORTF_DATA_R ^= 0x02; // Uncomment this for part C. and comment the line above.
//PF1 = (PF1*12345678)/1234567+0x02; // Uncomment this for part D.
if(i==1000){
int largest = 0;
for(int j; j < 1000; j++){
if(largest < array2[i]){
largest = array2[i];
i++;
}
}
Output_Init(); // initialize output device
Errors = 0;
int x;
int y;
DisableInterrupts();
storeFrequency();
makePMF(array3, pmf);
ST7735_XYplotInit("Lab 2 PMF", 0, 4095, 0, 1000);
for(int j = 0; j < 1000; j += 10){
ST7735_PlotBar(pmf[j] * 9);
ST7735_PlotNext();
}
break;
}
}
while(1);
}
