void HAL_USART_End(HAL_USART_Serial serial)
{
// wait for transmission of outgoing data
while (usartMap[serial]->usart_tx_buffer->head != usartMap[serial]->usart_tx_buffer->tail);
// Disable the USART
USART_Cmd(usartMap[serial]->usart_peripheral, DISABLE);
// Switch pins to INPUT
HAL_Pin_Mode(usartMap[serial]->usart_rx_pin, INPUT);
HAL_Pin_Mode(usartMap[serial]->usart_tx_pin, INPUT);
// Disable LIN mode
USART_LINCmd(usartMap[serial]->usart_peripheral, DISABLE);
// Deinitialise USART
USART_DeInit(usartMap[serial]->usart_peripheral);
// Disable USART Receive and Transmit interrupts
USART_ITConfig(usartMap[serial]->usart_peripheral, USART_IT_RXNE, DISABLE);
USART_ITConfig(usartMap[serial]->usart_peripheral, USART_IT_TXE, DISABLE);
NVIC_InitTypeDef NVIC_InitStructure;
// Disable the USART Interrupt
NVIC_InitStructure.NVIC_IRQChannel = usartMap[serial]->usart_int_n;
NVIC_InitStructure.NVIC_IRQChannelCmd = DISABLE;
NVIC_Init(&NVIC_InitStructure);
// Disable USART Clock
*usartMap[serial]->usart_apbReg &= ~usartMap[serial]->usart_clock_en;
// clear any received data
usartMap[serial]->usart_rx_buffer->head = usartMap[serial]->usart_rx_buffer->tail;
// Undo any pin re-mapping done for this USART
GPIO_PinRemapConfig(usartMap[serial]->usart_pin_remap, DISABLE);
memset(usartMap[serial]->usart_rx_buffer, 0, sizeof(Ring_Buffer));
memset(usartMap[serial]->usart_tx_buffer, 0, sizeof(Ring_Buffer));
usartMap[serial]->usart_enabled = false;
usartMap[serial]->usart_transmitting = false;
}
/******************************************************************************
* USART1 Initialization Code Template
******************************************************************************/
void USART1__Init()
{
USART_InitTypeDef USART_InitStruct;
#if (STRCMP($modeSelect$, USART_MODE_SYNCHRONOUS) == 1)
//PUT_A_NEW_LINE_HERE
USART_ClockInitTypeDef USART_ClockInitStruct;
#endif
#if (!STRCMP($USARTIntSet$, 0))
NVIC_InitTypeDef NVIC_InitStructure;
#endif
//PUT_A_NEW_LINE_HERE
//
// Enable peripheral clock of USART1 and GPIOA
//
RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1, ENABLE);
//PUT_A_NEW_LINE_HERE
//
// USART Config
//
USART_InitStruct.USART_BaudRate = $baudRate$;
USART_InitStruct.USART_WordLength = $dataBits$;
USART_InitStruct.USART_StopBits = $stopBits$;
USART_InitStruct.USART_Parity = $parityBits$;
USART_InitStruct.USART_Mode = $modeSet$;
USART_InitStruct.USART_HardwareFlowControl = $HardwareFlowControl$;
USART_Init(USART1, &USART_InitStruct);
#if ($guardTime$ != 0)
//PUT_A_NEW_LINE_HERE
//
// Set Guard Time
//
USART_SetGuardTime(USART1, $guardTime$);
#endif
//PUT_A_NEW_LINE_HERE
USART_WakeUpConfig(USART1, $WakeUpmethod$);
//PUT_A_NEW_LINE_HERE
#if (STRCMP($modeSelect$, USART_MODE_NORMAL) == 1)
#elif (STRCMP($modeSelect$, USART_MODE_IRDA) == 1)
//PUT_A_NEW_LINE_HERE
//
//USART IrDA Mode Config
//
USART_IrDAConfig(USART1, $IrDAModeSel$);
USART_IrDACmd(USART1, ENABLE);
#elif (STRCMP($modeSelect$, USART_MODE_DMA) == 1)
//PUT_A_NEW_LINE_HERE
//
//USART DMA Mode Config
//
USART_DMACmd(USART1, $DMAReq$, ENABLE);
#elif (STRCMP($modeSelect$, USART_MODE_SYNCHRONOUS) == 1)
//PUT_A_NEW_LINE_HERE
//
// USART Synchronous Mode Config
//
USART_Clock_InitStruct.USART_Clock = USART_CLOCK_ENABLE;
USART_Clock_InitStruct.USART_CPOL = $synClockPolSet$;
USART_Clock_InitStruct.USART_CPHA = $synClockPhaseSet$;
USART_Clock_InitStruct.USART_LastBit = $lastbitenable$;
USART_ClockInit(USART1, &USART_Clock_InitStruct);
#elif (STRCMP($modeSelect$, USART_MODE_LIN) == 1)
//PUT_A_NEW_LINE_HERE
//
// USART LIN Mode Config
//
USART_LINBreakDetectLengthConfig(USART1, $LINBreakDetectLen$);
USART_LINCmd(USART1, ENABLE);
#elif (STRCMP($modeSelect$, USART_MODE_SMARTCARD) == 1)
//PUT_A_NEW_LINE_HERE
//
// USART SmartCard Mode Config
//
USART_SmartCardCmd(USART1, ENABLE);
#elif (STRCMP($NACKTrans$, ENABLE) == 1)
//PUT_A_NEW_LINE_HERE
USART_SmartCardNACKCmd(USART1, ENABLE);
#elif (STRCMP($modeSelect$, USART_MODE_HALFDUPLEX) == 1)
//PUT_A_NEW_LINE_HERE
//
// USART HalfDuplex Mode Config
//
USART_HalfDuplexCmd(USART1, ENABLE);
#endif
#if (!STRCMP($USARTIntSet$, 0))
//PUT_A_NEW_LINE_HERE
//
// Enable the USART Interrupt Function
//
USART_ITConfig(USART1, $USARTIntSet$, ENABLE);
NVIC_InitStructure.NVIC_IRQChannel = USART1_IRQn;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure);
#endif
}
void HAL_USART_BeginConfig(HAL_USART_Serial serial, uint32_t baud, uint32_t config, void *ptr)
{
// Verify UART configuration, exit if it's invalid.
if (!HAL_USART_Validate_Config(config)) {
usartMap[serial]->usart_enabled = false;
return;
}
usartMap[serial]->usart_enabled = false;
// AFIO clock enable
RCC_APB2PeriphClockCmd(RCC_APB2Periph_AFIO, ENABLE);
// Enable USART Clock
*usartMap[serial]->usart_apbReg |= usartMap[serial]->usart_clock_en;
NVIC_InitTypeDef NVIC_InitStructure;
// Enable the USART Interrupt
NVIC_InitStructure.NVIC_IRQChannel = usartMap[serial]->usart_int_n;
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 7;//USART2_IRQ_PRIORITY;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure);
HAL_USART_Configure_Pin_Modes(serial, config);
// USART default configuration
// USART configured as follow:
// - BaudRate = (set baudRate as 9600 baud)
// - Word Length = 8 Bits
// - One Stop Bit
// - No parity
// - Hardware flow control disabled (RTS and CTS signals)
// - Receive and transmit enabled
// USART configuration
USART_InitStructure.USART_BaudRate = baud;
USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;
switch (config & SERIAL_FLOW_CONTROL) {
case SERIAL_FLOW_CONTROL_CTS:
USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_CTS;
break;
case SERIAL_FLOW_CONTROL_RTS:
USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_RTS;
break;
case SERIAL_FLOW_CONTROL_RTS_CTS:
USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_RTS_CTS;
break;
case SERIAL_FLOW_CONTROL_NONE:
default:
USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
break;
}
if (serial == HAL_USART_SERIAL2) {
// USART1 supports hardware flow control, but RTS and CTS pins are not exposed
USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
}
switch (USART_InitStructure.USART_HardwareFlowControl) {
case USART_HardwareFlowControl_CTS:
HAL_Pin_Mode(usartMap[serial]->usart_cts_pin, AF_OUTPUT_PUSHPULL);
break;
case USART_HardwareFlowControl_RTS:
HAL_Pin_Mode(usartMap[serial]->usart_rts_pin, AF_OUTPUT_PUSHPULL);
break;
case USART_HardwareFlowControl_RTS_CTS:
HAL_Pin_Mode(usartMap[serial]->usart_cts_pin, AF_OUTPUT_PUSHPULL);
HAL_Pin_Mode(usartMap[serial]->usart_rts_pin, AF_OUTPUT_PUSHPULL);
break;
case USART_HardwareFlowControl_None:
default:
break;
}
// Stop bit configuration.
switch (config & SERIAL_STOP_BITS) {
case SERIAL_STOP_BITS_1: // 1 stop bit
USART_InitStructure.USART_StopBits = USART_StopBits_1;
break;
case SERIAL_STOP_BITS_2: // 2 stop bits
USART_InitStructure.USART_StopBits = USART_StopBits_2;
break;
case SERIAL_STOP_BITS_0_5: // 0.5 stop bits
USART_InitStructure.USART_StopBits = USART_StopBits_0_5;
break;
case SERIAL_STOP_BITS_1_5: // 1.5 stop bits
USART_InitStructure.USART_StopBits = USART_StopBits_1_5;
break;
}
// Data bits configuration
switch (HAL_USART_Calculate_Word_Length(config, 0)) {
case 8:
USART_InitStructure.USART_WordLength = USART_WordLength_8b;
break;
case 9:
USART_InitStructure.USART_WordLength = USART_WordLength_9b;
break;
}
// Parity configuration
switch (config & SERIAL_PARITY) {
case SERIAL_PARITY_NO:
USART_InitStructure.USART_Parity = USART_Parity_No;
break;
case SERIAL_PARITY_EVEN:
USART_InitStructure.USART_Parity = USART_Parity_Even;
break;
case SERIAL_PARITY_ODD:
USART_InitStructure.USART_Parity = USART_Parity_Odd;
break;
}
// Disable LIN mode just in case
USART_LINCmd(usartMap[serial]->usart_peripheral, DISABLE);
// Configure USART
USART_Init(usartMap[serial]->usart_peripheral, &USART_InitStructure);
// LIN configuration
if (config & LIN_MODE) {
// Enable break detection
switch(config & LIN_BREAK_BITS) {
case LIN_BREAK_10B:
USART_LINBreakDetectLengthConfig(usartMap[serial]->usart_peripheral, USART_LINBreakDetectLength_10b);
break;
case LIN_BREAK_11B:
USART_LINBreakDetectLengthConfig(usartMap[serial]->usart_peripheral, USART_LINBreakDetectLength_11b);
break;
}
}
// Enable USART Receive and Transmit interrupts
USART_ITConfig(usartMap[serial]->usart_peripheral, USART_IT_RXNE, ENABLE);
USART_ITConfig(usartMap[serial]->usart_peripheral, USART_IT_TXE, ENABLE);
usartMap[serial]->usart_config = config;
if (config & SERIAL_HALF_DUPLEX) {
HAL_USART_Half_Duplex(serial, ENABLE);
}
USART_ITConfig(usartMap[serial]->usart_peripheral, USART_IT_TC, DISABLE);
// Enable the USART
USART_Cmd(usartMap[serial]->usart_peripheral, ENABLE);
if (config & LIN_MODE) {
USART_LINCmd(usartMap[serial]->usart_peripheral, ENABLE);
}
usartMap[serial]->usart_enabled = true;
usartMap[serial]->usart_transmitting = false;
}