/**
* Handle the USB setup package received, should be invoked
* when an endpoint got a setup package as request.
* \param bEndpoint Endpoint number.
* \param pRequest Pointer to content of request.
*/
void USBD_RequestHandler(uint8_t bEndpoint,
const USBGenericRequest* pRequest)
{
if (bEndpoint != 0) {
TRACE_WARNING("EP%d request not supported, default EP only",
bEndpoint);
} else {
USBDCallbacks_RequestReceived(pRequest);
}
}
/*
Function: UDP_EndpointHandler
Endpoint interrupt handler. Manages IN, OUT & SETUP transaction, as well
as the STALL condition.
Parameters:
eptnum - Number of the endpoint to handle interrupt for.
*/
static void UDP_EndpointHandler(unsigned char eptnum)
{
Endpoint *endpoint = &(endpoints[eptnum]);
Transfer *transfer = &(endpoint->transfer);
unsigned int status = AT91C_BASE_UDP->UDP_CSR[eptnum];
//TRACE_INFO( "Ept%d ", eptnum);
//TRACE_INFO( "[");
// Handle interrupts
// IN packet sent
if ((status & AT91C_UDP_TXCOMP) != 0) {
//TRACE_INFO( "Wr ");
// Check that endpoint was in Sending state
if (endpoint->state == UDP_ENDPOINT_SENDING) {
// End of transfer ?
if (UDP_IsTransferFinished(eptnum)) {
// TRACE_INFO( "%d ", transfer->buffered);
transfer->transferred += transfer->buffered;
transfer->buffered = 0;
// Disable interrupt if this is not a control endpoint
if ((status & AT91C_UDP_EPTYPE) != AT91C_UDP_EPTYPE_CTRL) {
AT91C_BASE_UDP->UDP_IDR = 1 << eptnum;
}
UDP_EndOfTransfer(eptnum, USBD_STATUS_SUCCESS);
CLEAR_CSR(eptnum, AT91C_UDP_TXCOMP);
}
else {
// Transfer remaining data
//TRACE_INFO( "PQ:%d ", endpoint->size);
transfer->transferred += endpoint->size;
transfer->buffered -= endpoint->size;
// Send next packet
if (BOARD_USB_ENDPOINTS_BANKS(eptnum) == 1) {
// No double buffering
UDP_WritePayload(eptnum);
SET_CSR(eptnum, AT91C_UDP_TXPKTRDY);
CLEAR_CSR(eptnum, AT91C_UDP_TXCOMP);
}
else {
// Double buffering
SET_CSR(eptnum, AT91C_UDP_TXPKTRDY);
CLEAR_CSR(eptnum, AT91C_UDP_TXCOMP);
UDP_WritePayload(eptnum);
}
}
}
else {
// Acknowledge interrupt
CLEAR_CSR(eptnum, AT91C_UDP_TXCOMP);
}
}
// OUT packet received
if ((status & UDP_RXDATA) != 0) {
//TRACE_INFO( "Rd ");
// Check that the endpoint is in Receiving state
if (endpoint->state != UDP_ENDPOINT_RECEIVING) {
// Check if an ACK has been received on a Control endpoint
if (((status & AT91C_UDP_EPTYPE) == AT91C_UDP_EPTYPE_CTRL)
&& ((status & AT91C_UDP_RXBYTECNT) == 0)) {
// Acknowledge the data and finish the current transfer
///TRACE_INFO( "[%d]Ack ",eptnum);
UDP_ClearRxFlag(eptnum);
UDP_EndOfTransfer(eptnum, USBD_STATUS_SUCCESS);
}
// Check if the data has been STALLed
else if ((status & AT91C_UDP_FORCESTALL) != 0) {
// Discard STALLed data
TRACE_INFO( "[%d]Disc ",eptnum);
UDP_ClearRxFlag(eptnum);
}
// NAK the data
else {
TRACE_INFO( "[%d]Nak ",eptnum);
AT91C_BASE_UDP->UDP_IDR = 1 << eptnum;
}
}
// Endpoint is in Read state
else {
// Retrieve data and store it into the current transfer buffer
unsigned short size = (unsigned short) (status >> 16);
//TRACE_INFO( "-[%d]-", size);
//TRACE_INFO( "Rec ");
UDP_ReadPayload(eptnum, size);
UDP_ClearRxFlag(eptnum);
// Check if the transfer is finished
if ((transfer->remaining == 0) || (size < endpoint->size)) {
// Disable interrupt if this is not a control endpoint
if ((status & AT91C_UDP_EPTYPE) != AT91C_UDP_EPTYPE_CTRL) {
AT91C_BASE_UDP->UDP_IDR = 1 << eptnum;
}
UDP_EndOfTransfer(eptnum, USBD_STATUS_SUCCESS);
}
}
}
// SETUP packet received
if ((status & AT91C_UDP_RXSETUP) != 0) {
//TRACE_INFO( "Stp ");
// If a transfer was pending, complete it
// Handles the case where during the status phase of a control write
// transfer, the host receives the device ZLP and ack it, but the ack
// is not received by the device
if ((endpoint->state == UDP_ENDPOINT_RECEIVING)
|| (endpoint->state == UDP_ENDPOINT_SENDING)) {
UDP_EndOfTransfer(eptnum, USBD_STATUS_SUCCESS);
}
USBGenericRequest request;
UDP_ReadRequest(&request);
// Set the DIR bit before clearing RXSETUP in Control IN sequence
if (USBGenericRequest_GetDirection(&request) == USBGenericRequest_IN) {
SET_CSR(eptnum, AT91C_UDP_DIR);
}
CLEAR_CSR(eptnum, AT91C_UDP_RXSETUP);
// Forward the request to the upper layer
USBDCallbacks_RequestReceived(&request);//------------------------------------
}
// STALL sent
if ((status & AT91C_UDP_STALLSENT) != 0) {
TRACE_INFO( "STA ");
// If the endpoint is not halted, clear the STALL condition
CLEAR_CSR(eptnum, AT91C_UDP_STALLSENT);
if (endpoint->state != UDP_ENDPOINT_HALTED) {
CLEAR_CSR(eptnum, AT91C_UDP_FORCESTALL);
}
}
//TRACE_INFO( "]");
}
