/**
Enumerate all the changed hub ports.
@param Event The event that is triggered.
@param Context The context to the event.
**/
VOID
EFIAPI
UsbRootHubEnumeration (
IN EFI_EVENT Event,
IN VOID *Context
)
{
USB_INTERFACE *RootHub;
UINT8 Index;
USB_DEVICE *Child;
RootHub = (USB_INTERFACE *) Context;
if (!RootHub) {
return;
}
DBG("USB event happen, NumOfPort=%d\n", RootHub->NumOfPort);
for (Index = 0; Index < RootHub->NumOfPort; Index++) {
Child = UsbFindChild (RootHub, Index);
if ((Child != NULL) && (Child->DisconnectFail == TRUE)) {
// DEBUG (( EFI_D_INFO, "UsbEnumeratePort: The device disconnect fails at port %d from root hub %p, try again\n", Index, RootHub));
DBG("UsbEnumeratePort: The device disconnect fails at port %d from root hub %p, try again\n", Index, RootHub);
UsbRemoveDevice (Child);
DBG("device removed\n");
}
UsbEnumeratePort (RootHub, Index);
}
}
/**
Enumerate all the changed hub ports.
@param Event The event that is triggered.
@param Context The context to the event.
**/
VOID
EFIAPI
UsbHubEnumeration (
IN EFI_EVENT Event,
IN VOID *Context
)
{
USB_INTERFACE *HubIf;
UINT8 Byte;
UINT8 Bit;
UINT8 Index;
USB_DEVICE *Child;
// ASSERT (Context != NULL);
if (!Context) {
return;
}
HubIf = (USB_INTERFACE *) Context;
for (Index = 0; Index < HubIf->NumOfPort; Index++) {
Child = UsbFindChild (HubIf, Index);
if ((Child != NULL) && (Child->DisconnectFail == TRUE)) {
// DEBUG (( EFI_D_INFO, "UsbEnumeratePort: The device disconnect fails at port %d from hub %p, try again\n", Index, HubIf));
DBG("UsbEnumeratePort: The device disconnect fails at port %d from hub %p, try again\n", Index, HubIf);
UsbRemoveDevice (Child);
}
}
if (HubIf->ChangeMap == NULL) {
return ;
}
//
// HUB starts its port index with 1.
//
Byte = 0;
Bit = 1;
DBG("Enumerate %d ports\n", HubIf->NumOfPort);
for (Index = 0; Index < HubIf->NumOfPort; Index++) {
if (USB_BIT_IS_SET (HubIf->ChangeMap[Byte], USB_BIT (Bit))) {
UsbEnumeratePort (HubIf, Index);
DBG("Port %d enumerated\n", Index);
}
USB_NEXT_BIT (Byte, Bit);
}
UsbHubAckHubStatus (HubIf->Device);
gBS->FreePool (HubIf->ChangeMap);
HubIf->ChangeMap = NULL;
return ;
}
/**
Process the events on the port.
@param HubIf The HUB that has the device connected.
@param Port The port index of the hub (started with zero).
@retval EFI_SUCCESS The device is enumerated (added or removed).
@retval EFI_OUT_OF_RESOURCES Failed to allocate resource for the device.
@retval Others Failed to enumerate the device.
**/
EFI_STATUS
UsbEnumeratePort (
IN USB_INTERFACE *HubIf,
IN UINT8 Port
)
{
USB_HUB_API *HubApi;
USB_DEVICE *Child;
EFI_USB_PORT_STATUS PortState;
EFI_STATUS Status;
Child = NULL;
HubApi = HubIf->HubApi;
//
// Host learns of the new device by polling the hub for port changes.
//
Status = HubApi->GetPortStatus (HubIf, Port, &PortState);
if (EFI_ERROR (Status)) {
// DEBUG ((EFI_D_ERROR, "UsbEnumeratePort: failed to get state of port %d\n", Port));
DBG("UsbEnumeratePort: failed to get state of port %d\n", Port);
return Status;
}
//
// Only handle connection/enable/overcurrent/reset change.
// Usb super speed hub may report other changes, such as warm reset change. Ignore them.
//
if ((PortState.PortChangeStatus & (USB_PORT_STAT_C_CONNECTION | USB_PORT_STAT_C_ENABLE | USB_PORT_STAT_C_OVERCURRENT | USB_PORT_STAT_C_RESET)) == 0) {
return EFI_SUCCESS;
}
// DEBUG (( EFI_D_INFO, "UsbEnumeratePort: port %d state - %02x, change - %02x on %p\n",
//Port, PortState.PortStatus, PortState.PortChangeStatus, HubIf));
DBG( "UsbEnumeratePort: port %d state - %02x, change - %02x on %p\n",
Port, PortState.PortStatus, PortState.PortChangeStatus, HubIf);
//
// This driver only process two kinds of events now: over current and
// connect/disconnect. Other three events are: ENABLE, SUSPEND, RESET.
// ENABLE/RESET is used to reset port. SUSPEND isn't supported.
//
if (USB_BIT_IS_SET (PortState.PortChangeStatus, USB_PORT_STAT_C_OVERCURRENT)) {
if (USB_BIT_IS_SET (PortState.PortStatus, USB_PORT_STAT_OVERCURRENT)) {
//
// Case1:
// Both OverCurrent and OverCurrentChange set, means over current occurs,
// which probably is caused by short circuit. It has to wait system hardware
// to perform recovery.
//
// DEBUG (( EFI_D_ERROR, "UsbEnumeratePort: Critical Over Current\n", Port));
DBG("UsbEnumeratePort: Critical Over Current\n", Port);
return EFI_DEVICE_ERROR;
}
//
// Case2:
// Only OverCurrentChange set, means system has been recoveried from
// over current. As a result, all ports are nearly power-off, so
// it's necessary to detach and enumerate all ports again.
//
// DEBUG (( EFI_D_ERROR, "UsbEnumeratePort: 2.0 device Recovery Over Current\n", Port));
DBG("UsbEnumeratePort: 2.0 device Recovery Over Current\n", Port);
}
if (USB_BIT_IS_SET (PortState.PortChangeStatus, USB_PORT_STAT_C_ENABLE)) {
//
// Case3:
// 1.1 roothub port reg doesn't reflect over-current state, while its counterpart
// on 2.0 roothub does. When over-current has influence on 1.1 device, the port
// would be disabled, so it's also necessary to detach and enumerate again.
//
// DEBUG (( EFI_D_ERROR, "UsbEnumeratePort: 1.1 device Recovery Over Current\n", Port));
DBG("UsbEnumeratePort: 1.1 device Recovery Over Current\n", Port);
}
if (USB_BIT_IS_SET (PortState.PortChangeStatus, USB_PORT_STAT_C_CONNECTION)) {
//
// Case4:
// Device connected or disconnected normally.
//
// DEBUG ((EFI_D_ERROR, "UsbEnumeratePort: Device Connect/Discount Normally\n", Port));
DBG("UsbEnumeratePort: Device Connect/Discount Normally\n");
}
//
// Following as the above cases, it's safety to remove and create again.
//
Child = UsbFindChild (HubIf, Port);
if (Child != NULL) {
// DEBUG (( EFI_D_INFO, "UsbEnumeratePort: device at port %d removed from root hub %p\n", Port, HubIf));
DBG("UsbEnumeratePort: device at port %d removed from root hub %p\n", Port, HubIf);
UsbRemoveDevice (Child);
}
if (USB_BIT_IS_SET (PortState.PortStatus, USB_PORT_STAT_CONNECTION)) {
//
// Now, new device connected, enumerate and configure the device
//
// DEBUG (( EFI_D_INFO, "UsbEnumeratePort: new device connected at port %d\n", Port));
DBG("UsbEnumeratePort: new device connected at port %d\n", Port);
Status = UsbEnumerateNewDev (HubIf, Port);
} else {
// DEBUG (( EFI_D_INFO, "UsbEnumeratePort: device disconnected event on port %d\n", Port));
DBG("UsbEnumeratePort: device disconnected event on port %d status=0x%x\n", Port, PortState.PortStatus);
}
HubApi->ClearPortChange (HubIf, Port);
DBG("ClearPortChange\n");
return Status;
}
STATIC
EFI_STATUS
UsbEnumeratePort (
IN USB_INTERFACE *HubIf,
IN UINT8 Port
)
/*++
Routine Description:
Process the events on the port.
Arguments:
HubIf - The HUB that has the device connected
Port - The port index of the hub (started with zero)
Returns:
EFI_SUCCESS - The device is enumerated (added or removed)
EFI_OUT_OF_RESOURCES - Failed to allocate resource for the device
Others - Failed to enumerate the device
--*/
{
USB_HUB_API *HubApi;
USB_DEVICE *Child;
EFI_USB_PORT_STATUS PortState;
EFI_STATUS Status;
Child = NULL;
HubApi = HubIf->HubApi;
//
// Host learns of the new device by polling the hub for port changes.
//
Status = HubApi->GetPortStatus (HubIf, Port, &PortState);
if (EFI_ERROR (Status)) {
USB_ERROR (("UsbEnumeratePort: failed to get state of port %d\n", Port));
return Status;
}
if (PortState.PortChangeStatus == 0) {
return EFI_SUCCESS;
}
USB_DEBUG (("UsbEnumeratePort: port %d state - %x, change - %x\n",
Port, PortState.PortStatus, PortState.PortChangeStatus));
//
// This driver only process two kinds of events now: over current and
// connect/disconnect. Other three events are: ENABLE, SUSPEND, RESET.
// ENABLE/RESET is used to reset port. SUSPEND isn't supported.
//
if (USB_BIT_IS_SET (PortState.PortChangeStatus, USB_PORT_STAT_C_OVERCURRENT)) {
if (USB_BIT_IS_SET (PortState.PortStatus, USB_PORT_STAT_OVERCURRENT)) {
//
// Case1:
// Both OverCurrent and OverCurrentChange set, means over current occurs,
// which probably is caused by short circuit. It has to wait system hardware
// to perform recovery.
//
USB_DEBUG (("UsbEnumeratePort: Critical Over Current\n", Port));
return EFI_DEVICE_ERROR;
}
//
// Case2:
// Only OverCurrentChange set, means system has been recoveried from
// over current. As a result, all ports are nearly power-off, so
// it's necessary to detach and enumerate all ports again.
//
USB_DEBUG (("UsbEnumeratePort: 2.0 Device Recovery Over Current\n", Port));
}
if (USB_BIT_IS_SET (PortState.PortChangeStatus, USB_PORT_STAT_C_ENABLE)) {
//
// Case3:
// 1.1 roothub port reg doesn't reflect over-current state, while its counterpart
// on 2.0 roothub does. When over-current has influence on 1.1 device, the port
// would be disabled, so it's also necessary to detach and enumerate again.
//
USB_DEBUG (("UsbEnumeratePort: 1.1 Device Recovery Over Current\n", Port));
}
if (USB_BIT_IS_SET (PortState.PortChangeStatus, USB_PORT_STAT_C_CONNECTION)) {
//
// Case4:
// Device connected or disconnected normally.
//
USB_DEBUG (("UsbEnumeratePort: Device Connect/Discount Normally\n", Port));
}
//
// Following as the above cases, it's safety to remove and create again.
//
Child = UsbFindChild (HubIf, Port);
if (Child != NULL) {
USB_DEBUG (("UsbEnumeratePort: device at port %d removed from system\n", Port));
UsbRemoveDevice (Child);
}
if (USB_BIT_IS_SET (PortState.PortStatus, USB_PORT_STAT_CONNECTION)) {
//
// Now, new device connected, enumerate and configure the device
//
USB_DEBUG (("UsbEnumeratePort: new device connected at port %d\n", Port));
Status = UsbEnumerateNewDev (HubIf, Port);
} else {
USB_DEBUG (("UsbEnumeratePort: device disconnected event on port %d\n", Port));
}
HubApi->ClearPortChange (HubIf, Port);
return Status;
}
