int
MPU9250::gyro_ioctl(struct file *filp, int cmd, unsigned long arg)
{
switch (cmd) {
/* these are shared with the accel side */
case SENSORIOCSPOLLRATE:
case SENSORIOCGPOLLRATE:
case SENSORIOCRESET:
return ioctl(filp, cmd, arg);
case SENSORIOCSQUEUEDEPTH: {
/* lower bound is mandatory, upper bound is a sanity check */
if ((arg < 1) || (arg > 100)) {
return -EINVAL;
}
irqstate_t flags = px4_enter_critical_section();
if (!_gyro_reports->resize(arg)) {
px4_leave_critical_section(flags);
return -ENOMEM;
}
px4_leave_critical_section(flags);
return OK;
}
case SENSORIOCGQUEUEDEPTH:
return _gyro_reports->size();
case GYROIOCGSAMPLERATE:
return _sample_rate;
case GYROIOCSSAMPLERATE:
_set_sample_rate(arg);
return OK;
case GYROIOCGLOWPASS:
return _gyro_filter_x.get_cutoff_freq();
case GYROIOCSLOWPASS:
// set software filtering
_gyro_filter_x.set_cutoff_frequency(1.0e6f / _call_interval, arg);
_gyro_filter_y.set_cutoff_frequency(1.0e6f / _call_interval, arg);
_gyro_filter_z.set_cutoff_frequency(1.0e6f / _call_interval, arg);
return OK;
case GYROIOCSSCALE:
/* copy scale in */
memcpy(&_gyro_scale, (struct gyro_calibration_s *) arg, sizeof(_gyro_scale));
return OK;
case GYROIOCGSCALE:
/* copy scale out */
memcpy((struct gyro_calibration_s *) arg, &_gyro_scale, sizeof(_gyro_scale));
return OK;
case GYROIOCSRANGE:
/* XXX not implemented */
// XXX change these two values on set:
// _gyro_range_scale = xx
// _gyro_range_rad_s = xx
return -EINVAL;
case GYROIOCGRANGE:
return (unsigned long)(_gyro_range_rad_s * 180.0f / M_PI_F + 0.5f);
case GYROIOCSELFTEST:
return gyro_self_test();
#ifdef GYROIOCSHWLOWPASS
case GYROIOCSHWLOWPASS:
_set_dlpf_filter(arg);
return OK;
#endif
#ifdef GYROIOCGHWLOWPASS
case GYROIOCGHWLOWPASS:
return _dlpf_freq;
#endif
default:
/* give it to the superclass */
return CDev::ioctl(filp, cmd, arg);
}
}
int
MPU9250::ioctl(struct file *filp, int cmd, unsigned long arg)
{
switch (cmd) {
case SENSORIOCRESET:
return reset();
case SENSORIOCSPOLLRATE: {
switch (arg) {
/* switching to manual polling */
case SENSOR_POLLRATE_MANUAL:
stop();
_call_interval = 0;
return OK;
/* external signalling not supported */
case SENSOR_POLLRATE_EXTERNAL:
/* zero would be bad */
case 0:
return -EINVAL;
/* set default/max polling rate */
case SENSOR_POLLRATE_MAX:
return ioctl(filp, SENSORIOCSPOLLRATE, 1000);
case SENSOR_POLLRATE_DEFAULT:
return ioctl(filp, SENSORIOCSPOLLRATE, MPU9250_ACCEL_DEFAULT_RATE);
/* adjust to a legal polling interval in Hz */
default: {
/* do we need to start internal polling? */
bool want_start = (_call_interval == 0);
/* convert hz to hrt interval via microseconds */
unsigned ticks = 1000000 / arg;
/* check against maximum sane rate */
if (ticks < 1000) {
return -EINVAL;
}
// adjust filters
float cutoff_freq_hz = _accel_filter_x.get_cutoff_freq();
float sample_rate = 1.0e6f / ticks;
_set_dlpf_filter(cutoff_freq_hz);
_accel_filter_x.set_cutoff_frequency(sample_rate, cutoff_freq_hz);
_accel_filter_y.set_cutoff_frequency(sample_rate, cutoff_freq_hz);
_accel_filter_z.set_cutoff_frequency(sample_rate, cutoff_freq_hz);
float cutoff_freq_hz_gyro = _gyro_filter_x.get_cutoff_freq();
_set_dlpf_filter(cutoff_freq_hz_gyro);
_gyro_filter_x.set_cutoff_frequency(sample_rate, cutoff_freq_hz_gyro);
_gyro_filter_y.set_cutoff_frequency(sample_rate, cutoff_freq_hz_gyro);
_gyro_filter_z.set_cutoff_frequency(sample_rate, cutoff_freq_hz_gyro);
/* update interval for next measurement */
/* XXX this is a bit shady, but no other way to adjust... */
_call_interval = ticks;
/*
set call interval faster than the sample time. We
then detect when we have duplicate samples and reject
them. This prevents aliasing due to a beat between the
stm32 clock and the mpu9250 clock
*/
_call.period = _call_interval - MPU9250_TIMER_REDUCTION;
/* if we need to start the poll state machine, do it */
if (want_start) {
start();
}
return OK;
}
}
}
case SENSORIOCGPOLLRATE:
if (_call_interval == 0) {
return SENSOR_POLLRATE_MANUAL;
}
return 1000000 / _call_interval;
case SENSORIOCSQUEUEDEPTH: {
/* lower bound is mandatory, upper bound is a sanity check */
if ((arg < 1) || (arg > 100)) {
return -EINVAL;
}
irqstate_t flags = px4_enter_critical_section();
if (!_accel_reports->resize(arg)) {
px4_leave_critical_section(flags);
return -ENOMEM;
}
px4_leave_critical_section(flags);
return OK;
}
case SENSORIOCGQUEUEDEPTH:
return _accel_reports->size();
case ACCELIOCGSAMPLERATE:
return _sample_rate;
case ACCELIOCSSAMPLERATE:
_set_sample_rate(arg);
return OK;
case ACCELIOCGLOWPASS:
return _accel_filter_x.get_cutoff_freq();
case ACCELIOCSLOWPASS:
// set software filtering
_accel_filter_x.set_cutoff_frequency(1.0e6f / _call_interval, arg);
_accel_filter_y.set_cutoff_frequency(1.0e6f / _call_interval, arg);
_accel_filter_z.set_cutoff_frequency(1.0e6f / _call_interval, arg);
return OK;
case ACCELIOCSSCALE: {
/* copy scale, but only if off by a few percent */
struct accel_calibration_s *s = (struct accel_calibration_s *) arg;
float sum = s->x_scale + s->y_scale + s->z_scale;
if (sum > 2.0f && sum < 4.0f) {
memcpy(&_accel_scale, s, sizeof(_accel_scale));
return OK;
} else {
return -EINVAL;
}
}
case ACCELIOCGSCALE:
/* copy scale out */
memcpy((struct accel_calibration_s *) arg, &_accel_scale, sizeof(_accel_scale));
return OK;
case ACCELIOCSRANGE:
return set_accel_range(arg);
case ACCELIOCGRANGE:
return (unsigned long)((_accel_range_m_s2) / MPU9250_ONE_G + 0.5f);
case ACCELIOCSELFTEST:
return accel_self_test();
#ifdef ACCELIOCSHWLOWPASS
case ACCELIOCSHWLOWPASS:
_set_dlpf_filter(arg);
return OK;
#endif
#ifdef ACCELIOCGHWLOWPASS
case ACCELIOCGHWLOWPASS:
return _dlpf_freq;
#endif
default:
/* give it to the superclass */
return CDev::ioctl(filp, cmd, arg);
}
}
int MPU9250::reset_mpu()
{
uint8_t retries;
switch (_whoami) {
case MPU_WHOAMI_9250:
case MPU_WHOAMI_6500:
write_reg(MPUREG_PWR_MGMT_1, BIT_H_RESET);
write_checked_reg(MPUREG_PWR_MGMT_1, MPU_CLK_SEL_AUTO);
write_checked_reg(MPUREG_PWR_MGMT_2, 0);
usleep(1000);
break;
}
// Enable I2C bus or Disable I2C bus (recommended on data sheet)
write_checked_reg(MPUREG_USER_CTRL, is_i2c() ? 0 : BIT_I2C_IF_DIS);
// SAMPLE RATE
_set_sample_rate(_sample_rate);
_set_dlpf_filter(MPU9250_DEFAULT_ONCHIP_FILTER_FREQ);
// Gyro scale 2000 deg/s ()
switch (_whoami) {
case MPU_WHOAMI_9250:
case MPU_WHOAMI_6500:
write_checked_reg(MPUREG_GYRO_CONFIG, BITS_FS_2000DPS);
break;
}
// correct gyro scale factors
// scale to rad/s in SI units
// 2000 deg/s = (2000/180)*PI = 34.906585 rad/s
// scaling factor:
// 1/(2^15)*(2000/180)*PI
_gyro_range_scale = (0.0174532 / 16.4);//1.0f / (32768.0f * (2000.0f / 180.0f) * M_PI_F);
_gyro_range_rad_s = (2000.0f / 180.0f) * M_PI_F;
set_accel_range(ACCEL_RANGE_G);
// INT CFG => Interrupt on Data Ready
write_checked_reg(MPUREG_INT_ENABLE, BIT_RAW_RDY_EN); // INT: Raw data ready
#ifdef USE_I2C
bool bypass = !_mag->is_passthrough();
#else
bool bypass = false;
#endif
/* INT: Clear on any read.
* If this instance is for a device is on I2C bus the Mag will have an i2c interface
* that it will use to access the either: a) the internal mag device on the internal I2C bus
* or b) it could be used to access a downstream I2C devices connected to the chip on
* it's AUX_{ASD|SCL} pins. In either case we need to disconnect (bypass) the internal master
* controller that chip provides as a SPI to I2C bridge.
* so bypass is true if the mag has an i2c non null interfaces.
*/
write_checked_reg(MPUREG_INT_PIN_CFG, BIT_INT_ANYRD_2CLEAR | (bypass ? BIT_INT_BYPASS_EN : 0));
write_checked_reg(MPUREG_ACCEL_CONFIG2, BITS_ACCEL_CONFIG2_41HZ);
retries = 3;
bool all_ok = false;
while (!all_ok && retries--) {
// Assume all checked values are as expected
all_ok = true;
uint8_t reg;
uint8_t bankcheck = 0;
for (uint8_t i = 0; i < _num_checked_registers; i++) {
if ((reg = read_reg(_checked_registers[i])) != _checked_values[i]) {
write_reg(_checked_registers[i], _checked_values[i]);
PX4_ERR("Reg %d is:%d s/b:%d Tries:%d - bank s/b %d, is %d", _checked_registers[i], reg, _checked_values[i], retries,
REG_BANK(_checked_registers[i]), bankcheck);
all_ok = false;
}
}
}
return all_ok ? OK : -EIO;
}
int MPU9250::reset()
{
write_reg(MPUREG_PWR_MGMT_1, BIT_H_RESET);
up_udelay(10000);
write_checked_reg(MPUREG_PWR_MGMT_1, MPU_CLK_SEL_AUTO);
up_udelay(1000);
write_checked_reg(MPUREG_PWR_MGMT_2, 0);
up_udelay(1000);
// SAMPLE RATE
_set_sample_rate(_sample_rate);
usleep(1000);
// FS & DLPF FS=2000 deg/s, DLPF = 20Hz (low pass filter)
// was 90 Hz, but this ruins quality and does not improve the
// system response
_set_dlpf_filter(MPU9250_DEFAULT_ONCHIP_FILTER_FREQ);
usleep(1000);
// Gyro scale 2000 deg/s ()
write_checked_reg(MPUREG_GYRO_CONFIG, BITS_FS_2000DPS);
usleep(1000);
// correct gyro scale factors
// scale to rad/s in SI units
// 2000 deg/s = (2000/180)*PI = 34.906585 rad/s
// scaling factor:
// 1/(2^15)*(2000/180)*PI
_gyro_range_scale = (0.0174532 / 16.4);//1.0f / (32768.0f * (2000.0f / 180.0f) * M_PI_F);
_gyro_range_rad_s = (2000.0f / 180.0f) * M_PI_F;
set_accel_range(16);
usleep(1000);
// INT CFG => Interrupt on Data Ready
write_checked_reg(MPUREG_INT_ENABLE, BIT_RAW_RDY_EN); // INT: Raw data ready
usleep(1000);
#ifdef USE_I2C
bool bypass = !_mag->is_passthrough();
#else
bool bypass = false;
#endif
write_checked_reg(MPUREG_INT_PIN_CFG,
BIT_INT_ANYRD_2CLEAR | (bypass ? BIT_INT_BYPASS_EN :
0)); // INT: Clear on any read, also use i2c bypass is master mode isn't needed
usleep(1000);
write_checked_reg(MPUREG_ACCEL_CONFIG2, BITS_ACCEL_CONFIG2_41HZ);
usleep(1000);
uint8_t retries = 10;
while (retries--) {
bool all_ok = true;
for (uint8_t i = 0; i < MPU9250_NUM_CHECKED_REGISTERS; i++) {
if (read_reg(_checked_registers[i]) != _checked_values[i]) {
write_reg(_checked_registers[i], _checked_values[i]);
all_ok = false;
}
}
if (all_ok) {
break;
}
}
return OK;
}
int MPU9250::reset()
{
irqstate_t state;
// Hold off sampling for 4 ms
state = px4_enter_critical_section();
_reset_wait = hrt_absolute_time() + 10000;
write_reg(MPUREG_PWR_MGMT_1, BIT_H_RESET);
write_checked_reg(MPUREG_PWR_MGMT_1, MPU_CLK_SEL_AUTO);
write_checked_reg(MPUREG_PWR_MGMT_2, 0);
px4_leave_critical_section(state);
usleep(1000);
// Enable I2C bus or Disable I2C bus (recommended on data sheet)
write_checked_reg(MPUREG_USER_CTRL, is_i2c() ? 0 : BIT_I2C_IF_DIS);
// SAMPLE RATE
_set_sample_rate(_sample_rate);
// FS & DLPF FS=2000 deg/s, DLPF = 20Hz (low pass filter)
// was 90 Hz, but this ruins quality and does not improve the
// system response
_set_dlpf_filter(MPU9250_DEFAULT_ONCHIP_FILTER_FREQ);
// Gyro scale 2000 deg/s ()
write_checked_reg(MPUREG_GYRO_CONFIG, BITS_FS_2000DPS);
// correct gyro scale factors
// scale to rad/s in SI units
// 2000 deg/s = (2000/180)*PI = 34.906585 rad/s
// scaling factor:
// 1/(2^15)*(2000/180)*PI
_gyro_range_scale = (0.0174532 / 16.4);//1.0f / (32768.0f * (2000.0f / 180.0f) * M_PI_F);
_gyro_range_rad_s = (2000.0f / 180.0f) * M_PI_F;
set_accel_range(ACCEL_RANGE_G);
// INT CFG => Interrupt on Data Ready
write_checked_reg(MPUREG_INT_ENABLE, BIT_RAW_RDY_EN); // INT: Raw data ready
#ifdef USE_I2C
bool bypass = !_mag->is_passthrough();
#else
bool bypass = false;
#endif
/* INT: Clear on any read.
* If this instance is for a device is on I2C bus the Mag will have an i2c interface
* that it will use to access the either: a) the internal mag device on the internal I2C bus
* or b) it could be used to access a downstream I2C devices connected to the chip on
* it's AUX_{ASD|SCL} pins. In either case we need to disconnect (bypass) the internal master
* controller that chip provides as a SPI to I2C bridge.
* so bypass is true if the mag has an i2c non null interfaces.
*/
write_checked_reg(MPUREG_INT_PIN_CFG, BIT_INT_ANYRD_2CLEAR | (bypass ? BIT_INT_BYPASS_EN : 0));
write_checked_reg(MPUREG_ACCEL_CONFIG2, BITS_ACCEL_CONFIG2_41HZ);
uint8_t retries = 3;
bool all_ok = false;
while (!all_ok && retries--) {
// Assume all checked values are as expected
all_ok = true;
uint8_t reg;
for (uint8_t i = 0; i < MPU9250_NUM_CHECKED_REGISTERS; i++) {
if ((reg = read_reg(_checked_registers[i])) != _checked_values[i]) {
write_reg(_checked_registers[i], _checked_values[i]);
PX4_ERR("Reg %d is:%d s/b:%d Tries:%d", _checked_registers[i], reg, _checked_values[i], retries);
all_ok = false;
}
}
}
return all_ok ? OK : -EIO;
}
