/** \brief Main function - init and loop to display ADC values */
int main(void)
{
/* GPIO pin/ADC-function map. */
const gpio_map_t ADCIFB_GPIO_MAP = {
{EXAMPLE_ADCIFB_PIN, EXAMPLE_ADCIFB_FUNCTION}
};
/* ADCIFB Configuration */
adcifb_opt_t adcifb_opt = {
/* Resolution mode */
.resolution = AVR32_ADCIFB_ACR_RES_12BIT,
/* Channels Sample & Hold Time in [0,15] */
.shtim = 15,
.ratio_clkadcifb_clkadc =
(sysclk_get_pba_hz() / EXAMPLE_TARGET_CLK_ADC_FREQ_HZ),
/*
* Startup time in [0,127], where
* Tstartup = startup * 8 * Tclk_adc (assuming Tstartup ~ 15us max)
*/
.startup = 3,
/* ADCIFB Sleep Mode disabled */
.sleep_mode_enable = false
};
uint32_t adc_data;
/* Initialize the system clocks */
sysclk_init();
/* Init debug serial line */
init_dbg_rs232(sysclk_get_pba_hz());
/* Assign and enable GPIO pins to the ADC function. */
gpio_enable_module(ADCIFB_GPIO_MAP,
sizeof(ADCIFB_GPIO_MAP) / sizeof(ADCIFB_GPIO_MAP[0]));
/* Enable and configure the ADCIFB module */
if (adcifb_configure(&AVR32_ADCIFB, &adcifb_opt) != PASS) {
/* Config error. */
while (true) {
gpio_tgl_gpio_pin(LED0_GPIO);
delay_ms(100);
}
}
/* Configure the trigger mode */
/* "No trigger, only software trigger can start conversions". */
if (adcifb_configure_trigger(&AVR32_ADCIFB, AVR32_ADCIFB_TRGMOD_NT, 0)
!= PASS) {
/* Config error. */
while (true) {
gpio_tgl_gpio_pin(LED1_GPIO);
delay_ms(100);
}
}
/* Enable the ADCIFB channel the battery is connected to. */
adcifb_channels_enable(&AVR32_ADCIFB, EXAMPLE_ADCIFB_CHANNEL_MASK);
while (true) {
while (adcifb_is_ready(&AVR32_ADCIFB) != true) {
/* Wait until the ADC is ready to perform a conversion. */
}
/* Start an ADCIFB conversion sequence. */
adcifb_start_conversion_sequence(&AVR32_ADCIFB);
while (adcifb_is_drdy(&AVR32_ADCIFB) != true) {
/* Wait until the converted data is available. */
}
/* Get the last converted data. */
adc_data = adcifb_get_last_data(&AVR32_ADCIFB);
/* Display the current voltage of the battery. */
print_dbg("\x1B[2J\x1B[H\r\nADCIFB Example\r\nHEX Value for "
EXAMPLE_ADCIFB_CHANNEL_NAME " : 0x");
print_dbg_hex(adc_data & AVR32_ADCIFB_LCDR_LDATA_MASK);
print_dbg("\r\n");
delay_ms(500);
/*
* Note1: there is a resistor bridge between the battery and the
* ADC pad on the AT32UC3L-EK. The data converted is thus half
* of
* the battery voltage.
*/
/*
* Note2: if the battery is not in place, the conversion is out
* of
* spec because the ADC input is then higher than ADVREF.
*/
}
}
//#####################################################
void adc_init(unsigned long chanels_mask, unsigned char mode, unsigned short period)
{
// Assign and enable GPIO pin to the ADC function.
if(chanels_mask & (1 << 0))
{
gpio_enable_module_pin(AVR32_ADCIFB_AD_0_PIN, AVR32_ADCIFB_AD_0_FUNCTION);
//adcifb_channels_enable(&AVR32_ADCIFB, 1 << 0);
}
if(chanels_mask & (1 << 1))
{
gpio_enable_module_pin(AVR32_ADCIFB_AD_1_PIN, AVR32_ADCIFB_AD_1_FUNCTION);
//adcifb_channels_enable(&AVR32_ADCIFB, 1 << 1);
}
if(chanels_mask & (1 << 2))
{
gpio_enable_module_pin(AVR32_ADCIFB_AD_2_PIN, AVR32_ADCIFB_AD_2_FUNCTION);
//adcifb_channels_enable(&AVR32_ADCIFB, 1 << 2);
}
if(chanels_mask & (1 << 3))
{
gpio_enable_module_pin(AVR32_ADCIFB_AD_3_PIN, AVR32_ADCIFB_AD_3_FUNCTION);
//adcifb_channels_enable(&AVR32_ADCIFB, 1 << 3);
}
if(chanels_mask & (1 << 4))
{
gpio_enable_module_pin(AVR32_ADCIFB_AD_4_PIN, AVR32_ADCIFB_AD_4_FUNCTION);
//adcifb_channels_enable(&AVR32_ADCIFB, 1 << 4);
}
if(chanels_mask & (1 << 5))
{
gpio_enable_module_pin(AVR32_ADCIFB_AD_5_PIN, AVR32_ADCIFB_AD_5_FUNCTION);
//adcifb_channels_enable(&AVR32_ADCIFB, 1 << 5);
}
if(chanels_mask & (1 << 6))
{
gpio_enable_module_pin(AVR32_ADCIFB_AD_6_PIN, AVR32_ADCIFB_AD_6_FUNCTION);
//adcifb_channels_enable(&AVR32_ADCIFB, 1 << 6);
}
if(chanels_mask & (1 << 7))
{
gpio_enable_module_pin(AVR32_ADCIFB_AD_7_PIN, AVR32_ADCIFB_AD_7_FUNCTION);
//adcifb_channels_enable(&AVR32_ADCIFB, 1 << 7);
}
unsigned long pba_clock = sysclk_get_pba_hz();
adcifb_opt_t adcifb_opt = {
.resolution = AVR32_ADCIFB_ACR_RES_8BIT,
.shtim = 15,
.ratio_clkadcifb_clkadc = pba_clock / 6000000,
.startup = 3,
.sleep_mode_enable = false
};
// Enable and configure the ADCIFB module
sysclk_enable_peripheral_clock(&AVR32_ADCIFB);
adcifb_configure(&AVR32_ADCIFB, &adcifb_opt);
// Configure the trigger (No trigger, only software trigger)
adcifb_configure_trigger(&AVR32_ADCIFB, mode /*AVR32_ADCIFB_TRGR_TRGMOD_PT*/, period);
adcifb_channels_enable(&AVR32_ADCIFB, chanels_mask);
}
//#####################################################
void adc_channels_enable_pio(unsigned long chanels_mask)
{
// Assign and enable GPIO pin to the ADC function.
if(chanels_mask & (1 << 0))
{
gpio_enable_module_pin(AVR32_ADCIFB_AD_0_PIN, AVR32_ADCIFB_AD_0_FUNCTION);
//adcifb_channels_enable(&AVR32_ADCIFB, 1 << 0);
}
if(chanels_mask & (1 << 1))
{
gpio_enable_module_pin(AVR32_ADCIFB_AD_1_PIN, AVR32_ADCIFB_AD_1_FUNCTION);
//adcifb_channels_enable(&AVR32_ADCIFB, 1 << 1);
}
if(chanels_mask & (1 << 2))
{
gpio_enable_module_pin(AVR32_ADCIFB_AD_2_PIN, AVR32_ADCIFB_AD_2_FUNCTION);
//adcifb_channels_enable(&AVR32_ADCIFB, 1 << 2);
}
if(chanels_mask & (1 << 3))
{
gpio_enable_module_pin(AVR32_ADCIFB_AD_3_PIN, AVR32_ADCIFB_AD_3_FUNCTION);
//adcifb_channels_enable(&AVR32_ADCIFB, 1 << 3);
}
if(chanels_mask & (1 << 4))
{
gpio_enable_module_pin(AVR32_ADCIFB_AD_4_PIN, AVR32_ADCIFB_AD_4_FUNCTION);
//adcifb_channels_enable(&AVR32_ADCIFB, 1 << 4);
}
if(chanels_mask & (1 << 5))
{
gpio_enable_module_pin(AVR32_ADCIFB_AD_5_PIN, AVR32_ADCIFB_AD_5_FUNCTION);
//adcifb_channels_enable(&AVR32_ADCIFB, 1 << 5);
}
if(chanels_mask & (1 << 6))
{
gpio_enable_module_pin(AVR32_ADCIFB_AD_6_PIN, AVR32_ADCIFB_AD_6_FUNCTION);
//adcifb_channels_enable(&AVR32_ADCIFB, 1 << 6);
}
if(chanels_mask & (1 << 7))
{
gpio_enable_module_pin(AVR32_ADCIFB_AD_7_PIN, AVR32_ADCIFB_AD_7_FUNCTION);
//adcifb_channels_enable(&AVR32_ADCIFB, 1 << 7);
}
adcifb_channels_enable(&AVR32_ADCIFB, chanels_mask);
}
//#####################################################
void adc_channels_enable(unsigned long chanels_mask)
{
adcifb_channels_enable(&AVR32_ADCIFB, chanels_mask);
}
/**
* \brief Initialize ADC driver to read the board temperature sensor.
*
* Initializes the board's ADC driver module and configures the ADC channel
* connected to the onboard NTC temperature sensor ready for conversions.
*/
static void init_adc(void)
{
// Assign and enable GPIO pin to the ADC function.
gpio_enable_module_pin(ADC_TEMPERATURE_PIN, ADC_TEMPERATURE_FUNCTION);
const adcifb_opt_t adcifb_opt = {
.resolution = AVR32_ADCIFB_ACR_RES_12BIT,
.shtim = 15,
.ratio_clkadcifb_clkadc = 2,
.startup = 3,
.sleep_mode_enable = false
};
// Enable and configure the ADCIFB module
sysclk_enable_peripheral_clock(&AVR32_ADCIFB);
adcifb_configure(&AVR32_ADCIFB, &adcifb_opt);
// Configure the trigger (No trigger, only software trigger)
adcifb_configure_trigger(&AVR32_ADCIFB, AVR32_ADCIFB_TRGMOD_NT, 0);
// Enable the ADCIFB channel to NTC temperature sensor
adcifb_channels_enable(&AVR32_ADCIFB, ADC_TEMPERATURE_CHANNEL);
}
/**
* \brief Initializes the USART.
*
* Initializes the board USART ready for serial data to be transmitted and
* received.
*/
static void init_usart(void)
{
const usart_options_t usart_options = {
.baudrate = 57600,
.charlength = 8,
.paritytype = USART_NO_PARITY,
.stopbits = USART_1_STOPBIT,
.channelmode = USART_NORMAL_CHMODE
};
// Initialize USART in RS232 mode with the requested settings.
sysclk_enable_peripheral_clock(USART);
usart_init_rs232(USART, &usart_options, sysclk_get_pba_hz());
}
/**
* \brief Initializes the PWM subsystem ready to generate the RGB LED PWM
* waves.
*
* Initializes the on-chip PWM module and configures the RGB LED PWM outputs so
* the the brightness of the three individual channels can be adjusted.
*/
static void init_pwm(void)
{
// GPIO pin/function map for the RGB LEDs.
gpio_enable_module_pin(LED_RED_PWMA, LED_PWMA_FUNCTION);
gpio_enable_module_pin(LED_GREEN_PWMA, LED_PWMA_FUNCTION);
gpio_enable_module_pin(LED_BLUE_PWMA, LED_PWMA_FUNCTION);
const scif_gclk_opt_t genclk3_opt = {
.clock_source = SCIF_GCCTRL_CPUCLOCK,
.divider = 8,
.diven = true,
};
// Start generic clock 3 for the PWM outputs.
scif_start_gclk(AVR32_PM_GCLK_GCLK3, &genclk3_opt);
// Enable RGB LED PWM.
sysclk_enable_peripheral_clock(&AVR32_PWMA);
pwma_config_enable(&AVR32_PWMA,EXAMPLE_PWMA_FREQUENCY,EXAMPLE_PWMA_GCLK_FREQUENCY,0);
pwma_set_channels_value(&AVR32_PWMA,PWM_CHANNEL_RED | PWM_CHANNEL_BLUE| PWM_CHANNEL_GREEN,255);
}
/**
* \brief Application main loop.
*/
int main(void)
{
board_init();
sysclk_init();
sysclk_enable_peripheral_clock(USART);
// Initialize touch, ADC, USART and PWM
init_adc();
init_usart();
init_pwm();
init_touch();
while (true) {
uint32_t adc_data;
// Read slider and button and update RGB led
touch_handler();
// Wait until the ADC is ready to perform a conversion.
do { } while (!adcifb_is_ready(&AVR32_ADCIFB));
// Start an ADCIFB conversion sequence.
adcifb_start_conversion_sequence(&AVR32_ADCIFB);
// Wait until the converted data is available.
do { } while (!adcifb_is_drdy(&AVR32_ADCIFB));
// Get the last converted data.
adc_data = (adcifb_get_last_data(&AVR32_ADCIFB) & 0x3FF);
// Write temperature data to USART
do { } while (!usart_tx_empty(USART));
usart_write_char(USART, (adc_data >> 8));
do { } while (!usart_tx_empty(USART));
usart_write_char(USART, (adc_data & 0xFF));
}
}
/**
* \brief Initializes the ADCIFB module with trigger
* - Initialize the trigger mode & compare interrupts for ADCIFB
*
* \retval STATUS_OK Configuration OK
* \retval ERR_TIMEOUT Timeout on configuring ADCIFB module
* \retval ERR_BUSY ADCIFB module unable to configure the trigger
*/
static status_code_t adc_init()
{
/* GPIO pin/adc - function map. */
static const gpio_map_t ADCIFB_GPIO_MAP = {
{EXAMPLE_ADCIFB_PIN, EXAMPLE_ADCIFB_FUNCTION}
};
/* ADCIFB Configuration */
adcifb_opt_t adcifb_opt = {
/* Resolution mode */
.resolution = AVR32_ADCIFB_ACR_RES_10BIT,
/* Channels Sample & Hold Time in [0,15] */
.shtim = ADC_SAMPLE_HOLD_TIME,
/* ADC Clock Prescaler */
.ratio_clkadcifb_clkadc = (sysclk_get_pba_hz()) / ADC_FREQUENCY,
.startup = ADC_STARTUP_TIME,
/* ADCIFB Sleep Mode enabled */
.sleep_mode_enable = true
};
/* Disable pull up on ADCIFB channel input pin */
gpio_disable_pin_pull_up(EXAMPLE_ADCIFB_PIN);
/* Enable the ADC pins */
gpio_enable_module(ADCIFB_GPIO_MAP,
sizeof(ADCIFB_GPIO_MAP) / sizeof(ADCIFB_GPIO_MAP[0]));
/* Enable ADCIFB clock */
sysclk_enable_pba_module(SYSCLK_ADCIFB);
/* Configure the ADCIFB peripheral */
if (adcifb_configure(adcifb, &adcifb_opt)) {
/* Error configuring the ADCIFB */
return ERR_TIMEOUT;
}
/* Configure the trigger for ADCIFB peripheral */
if (adcifb_configure_trigger(adcifb, AVR32_ADCIFB_TRGR_TRGMOD_EVT, 0)) {
/* Error configuring the trigger for ADCIFB */
return ERR_BUSY;
}
/* Enable ADCIFB Channel 0 */
adcifb_channels_enable(adcifb, EXAMPLE_ADCIFB_CHANNEL);
/* Disable global interrupts */
cpu_irq_disable();
/*
* Initialize the interrupt vectors
* Note: This function adds nothing for IAR as the interrupts are
* handled by the IAR compiler itself. It provides an abstraction
* between GCC & IAR compiler to use interrupts.
* Refer function implementation in interrupt_avr32.h
*/
irq_initialize_vectors();
/*
* Register the ADCIFB interrupt handler
* Note: This function adds nothing for IAR as the interrupts are
* handled by the IAR compiler itself. It provides an abstraction
* between GCC & IAR compiler to use interrupts.
* Refer function implementation in interrupt_avr32.h
*/
irq_register_handler(&ADCIFB_interrupt_handler, AVR32_ADCIFB_IRQ,
ADC_INTERRUPT_PRIORITY);
/*
* Set the threshold value in CVR.LV register to generate interrupt
* when the value detected is above the threshold.
* 1.500 V with 10-bit resolution
*/
adcifb_set_high_compare_value(adcifb, ADC_COMPARE_VALUE);
/* Enable the Analog Compare option in ADCIFB */
adcifb_enable_analog_compare_mode(adcifb);
/* Enable the data ready interrupt for ADCIFB */
adcifb_enable_compare_gt_interrupt(adcifb);
return STATUS_OK;
} /* End of adc_init() */
/**
* \brief Asynchronous Timer Initialization
* - Start the 32KHz Oscillator
* - Initializes the AST module with periodic trigger events
*
* \retval STATUS_OK Configuration OK
* \retval ERR_TIMEOUT Error in configuring the AST module
*/
static status_code_t ast_init()
{
/* Initial Count value to write in AST */
unsigned long ast_counter = 0;
/* Set the prescaler to set a periodic trigger from AST */
avr32_ast_pir0_t pir = {
.insel = AST_TRIGGER_PRESCALER
};
/* Set the OSC32 parameters */
scif_osc32_opt_t osc32_opt = {
.mode = SCIF_OSC_MODE_2PIN_CRYSTAL_HICUR,
.startup = OSC32_STARTUP_8192,
.pinsel = BOARD_OSC32_PINSEL,
.en1k = false,
.en32k = true
};
/* Enable the 32KHz Oscillator */
scif_start_osc32(&osc32_opt, true);
/* Enable the Peripheral Event System Clock */
sysclk_enable_hsb_module(SYSCLK_EVENT);
/* Enable PBA clock for AST clock to switch its source */
sysclk_enable_pba_module(SYSCLK_AST);
/* Initialize the AST in counter mode */
if (!ast_init_counter(&AVR32_AST, AST_CLOCK_SOURCE, AST_PRESCALER,
ast_counter)) {
return ERR_TIMEOUT;
}
/* Initialize the periodic value register with the prescaler */
ast_set_periodic0_value(&AVR32_AST, pir);
/* Enable the AST periodic event */
ast_enable_periodic0(&AVR32_AST);
/* Clear All AST Interrupt request and clear SR */
ast_clear_all_status_flags(&AVR32_AST);
/* Enable the AST */
ast_enable(&AVR32_AST);
/* Disable PBA clock for AST after switching its source to OSC32 */
sysclk_disable_pba_module(SYSCLK_AST);
return STATUS_OK;
} /* End of ast_init() */
/**
* \brief Low Power Configuration
* Initializes the power saving measures to reduce power consumption
* - Enable pullups on GPIO pins
* - Disable the clocks to unused modules
* - Disable internal voltage regulator when in 1.8V supply mode
*/
static void power_save_measures_init()
{
uint8_t i;
uint32_t gpio_mask[AVR32_GPIO_PORT_LENGTH] = {0};
/*
* Enable internal pull-ups on all unused GPIO pins
* Note: Pull-ups on Oscillator or JTAG pins can be enabled only if they
* are not used as an oscillator or JTAG pin respectively.
*/
for (i = 0; i < (sizeof(gpio_used_pins) / sizeof(uint32_t)); i++) {
gpio_mask[gpio_used_pins[i] >>
5] |= 1 << (gpio_used_pins[i] & 0x1F);
}
for (i = 0; i < AVR32_GPIO_PORT_LENGTH; i++) {
gpio_configure_group(i, ~(gpio_mask[i]),
GPIO_PULL_UP | GPIO_DIR_INPUT);
}
/* Disable OCD clock which is not disabled by sysclk service */
sysclk_disable_cpu_module(SYSCLK_OCD);
#if POWER_SUPPLY_MODE_1_8V
/*
* When using 1.8V Single supply mode, the Voltage Regulator can be
* shut-down using the code below, in-order to save power.
* See Voltage Regulator Calibration Register in datasheet for more
*info.
* CAUTION: When using 3.3V Single supply mode, the Voltage Regulator
* cannot be shut-down and the application will hang in this loop.
*/
uint32_t tmp = (AVR32_SCIF.vregcr);
tmp &= (~(1 << 5 | 1 << 18));
AVR32_SCIF.unlock = 0xAA000000 | AVR32_SCIF_VREGCR;
AVR32_SCIF.vregcr = tmp;
/* Wait until internal voltage regulator is disabled. */
while ((AVR32_SCIF.vregcr & 0x00040020)) {
}
#endif
} /* End of power_save_measures_init() */
