void soc_init_cpus(device_t dev)
{
struct bus *cpu_bus = dev->link_list;
const struct pattrs *pattrs = pattrs_get();
struct mp_params mp_params;
void *default_smm_area;
uint32_t bsmrwac;
printk(BIOS_SPEW, "%s/%s ( %s )\n",
__FILE__, __func__, dev_name(dev));
/* Set up MTRRs based on physical address size. */
x86_setup_fixed_mtrrs();
x86_setup_var_mtrrs(pattrs->address_bits, 2);
x86_mtrr_check();
mp_params.num_cpus = pattrs->num_cpus,
mp_params.parallel_microcode_load = 1,
mp_params.adjust_apic_id = adjust_apic_id;
mp_params.flight_plan = &mp_steps[0];
mp_params.num_records = ARRAY_SIZE(mp_steps);
mp_params.microcode_pointer = pattrs->microcode_patch;
default_smm_area = backup_default_smm_area();
/*
* Configure the BUNIT to allow dirty cache line evictions in non-SMM
* mode for the lines that were dirtied while in SMM mode. Otherwise
* the writes would be silently dropped.
*/
bsmrwac = iosf_bunit_read(BUNIT_SMRWAC) | SAI_IA_UNTRUSTED;
iosf_bunit_write(BUNIT_SMRWAC, bsmrwac);
/* Set package MSRs */
reg_script_run(package_msr_script);
/* Enable Turbo Mode on BSP and siblings of the BSP's building block. */
enable_turbo();
if (mp_init(cpu_bus, &mp_params))
printk(BIOS_ERR, "MP initialization failure.\n");
restore_default_smm_area(default_smm_area);
}
static void smm_relocate(void)
{
u32 smi_en;
u16 pm1_en;
printk(BIOS_DEBUG, "Initializing SMM handler...");
pmbase = pci_read_config16(pcidev_on_root(0x1f, 0), 0x40) & 0xfffc;
printk(BIOS_SPEW, " ... pmbase = 0x%04x\n", pmbase);
smi_en = inl(pmbase + SMI_EN);
if (smi_en & APMC_EN) {
printk(BIOS_INFO, "SMI# handler already enabled?\n");
return;
}
default_smm_area = backup_default_smm_area();
/* copy the SMM relocation code */
memcpy((void *)0x38000, &smm_relocation_start,
&smm_relocation_end - &smm_relocation_start);
wbinvd();
printk(BIOS_DEBUG, "\n");
dump_smi_status(reset_smi_status());
dump_pm1_status(reset_pm1_status());
dump_gpe0_status(reset_gpe0_status());
dump_alt_gp_smi_status(reset_alt_gp_smi_status());
dump_tco_status(reset_tco_status());
/* Enable SMI generation:
* - on TCO events
* - on APMC writes (io 0xb2)
* - on writes to SLP_EN (sleep states)
* - on writes to GBL_RLS (bios commands)
* No SMIs:
* - on microcontroller writes (io 0x62/0x66)
*/
smi_en = 0; /* reset SMI enables */
#if 0
smi_en |= LEGACY_USB2_EN | LEGACY_USB_EN;
#endif
smi_en |= TCO_EN;
smi_en |= APMC_EN;
#if DEBUG_PERIODIC_SMIS
/* Set DEBUG_PERIODIC_SMIS in i82801gx.h to debug using
* periodic SMIs.
*/
smi_en |= PERIODIC_EN;
#endif
smi_en |= SLP_SMI_EN;
smi_en |= BIOS_EN;
/* The following need to be on for SMIs to happen */
smi_en |= EOS | GBL_SMI_EN;
outl(smi_en, pmbase + SMI_EN);
pm1_en = 0;
pm1_en |= PWRBTN_EN;
pm1_en |= GBL_EN;
outw(pm1_en, pmbase + PM1_EN);
/**
* There are several methods of raising a controlled SMI# via
* software, among them:
* - Writes to io 0xb2 (APMC)
* - Writes to the Local Apic ICR with Delivery mode SMI.
*
* Using the local apic is a bit more tricky. According to
* AMD Family 11 Processor BKDG no destination shorthand must be
* used.
* The whole SMM initialization is quite a bit hardware specific, so
* I'm not too worried about the better of the methods at the moment
*/
/* raise an SMI interrupt */
printk(BIOS_SPEW, " ... raise SMI#\n");
outb(0x00, 0xb2);
}
