int bladerf_init_device(struct bladerf *dev)
{
int status;
unsigned int actual;
uint32_t val;
/* Readback the GPIO values to see if they are default or already set */
status = bladerf_config_gpio_read( dev, &val );
if (status != 0) {
log_warning("Failed to read GPIO config, skipping device initialization: %s\n",
bladerf_strerror(status));
return 0;
}
if ((val&0x7f) == 0) {
log_verbose( "Default GPIO value found - initializing device\n" );
/* Set the GPIO pins to enable the LMS and select the low band */
bladerf_config_gpio_write( dev, 0x57 );
/* Disable the front ends */
lms_enable_rffe(dev, BLADERF_MODULE_TX, false);
lms_enable_rffe(dev, BLADERF_MODULE_RX, false);
/* Set the internal LMS register to enable RX and TX */
bladerf_lms_write( dev, 0x05, 0x3e );
/* LMS FAQ: Improve TX spurious emission performance */
bladerf_lms_write( dev, 0x47, 0x40 );
/* LMS FAQ: Improve ADC performance */
bladerf_lms_write( dev, 0x59, 0x29 );
/* LMS FAQ: Common mode voltage for ADC */
bladerf_lms_write( dev, 0x64, 0x36 );
/* LMS FAQ: Higher LNA Gain */
bladerf_lms_write( dev, 0x79, 0x37 );
/* Set a default saplerate */
bladerf_set_sample_rate( dev, BLADERF_MODULE_TX, 1000000, &actual );
bladerf_set_sample_rate( dev, BLADERF_MODULE_RX, 1000000, &actual );
/* Set a default frequency of 1GHz */
bladerf_set_frequency( dev, BLADERF_MODULE_TX, 1000000000 );
bladerf_set_frequency( dev, BLADERF_MODULE_RX, 1000000000 );
/* Set the calibrated VCTCXO DAC value */
bladerf_dac_write( dev, dev->dac_trim );
}
/* TODO: Read this return from the SPI calls */
return 0;
}
int bladerf_init_device(struct bladerf *dev)
{
unsigned int actual;
uint32_t val;
/* Readback the GPIO values to see if they are default or already set */
bladerf_config_gpio_read( dev, &val );
if (val == 0) {
log_verbose( "Default GPIO value found - initializing device\n" );
/* Set the GPIO pins to enable the LMS and select the low band */
bladerf_config_gpio_write( dev, 0x57 );
/* Set the internal LMS register to enable RX and TX */
bladerf_lms_write( dev, 0x05, 0x3e );
/* LMS FAQ: Improve TX spurious emission performance */
bladerf_lms_write( dev, 0x47, 0x40 );
/* LMS FAQ: Improve ADC performance */
bladerf_lms_write( dev, 0x59, 0x29 );
/* LMS FAQ: Common mode voltage for ADC */
bladerf_lms_write( dev, 0x64, 0x36 );
/* LMS FAQ: Higher LNA Gain */
bladerf_lms_write( dev, 0x79, 0x37 );
/* FPGA workaround: Set IQ polarity for RX */
bladerf_lms_write( dev, 0x5a, 0xa0 );
/* Set a default saplerate */
bladerf_set_sample_rate( dev, BLADERF_MODULE_TX, 1000000, &actual );
bladerf_set_sample_rate( dev, BLADERF_MODULE_RX, 1000000, &actual );
/* Enable TX and RX */
bladerf_enable_module( dev, BLADERF_MODULE_TX, false );
bladerf_enable_module( dev, BLADERF_MODULE_RX, false );
/* Set a default frequency of 1GHz */
bladerf_set_frequency( dev, BLADERF_MODULE_TX, 1000000000 );
bladerf_set_frequency( dev, BLADERF_MODULE_RX, 1000000000 );
/* Set the calibrated VCTCXO DAC value */
bladerf_dac_write( dev, dev->dac_trim );
}
/* TODO: Read this return from the SPI calls */
return 0;
}
