/**
* \brief Test wakeup functions.
*
* \param test Current test case.
*/
static void run_picouart_test(const struct test_case *test)
{
uint8_t value;
Pm *p_pm = PM;
struct picouart_dev_inst dev_inst;
struct picouart_config config;
/* Init the PICOUART */
picouart_get_config_defaults(&config);
picouart_init(&dev_inst, PICOUART, &config);
/* Enable the PICOUART */
picouart_enable(&dev_inst);
delay_ms(30);
/* PICOUART can wakeup the device. */
bpm_enable_wakeup_source(BPM, (1 << BPM_BKUPWEN_PICOUART));
p_pm->PM_AWEN = 1 << PM_AWEN_PICOUART;
p_pm->PM_IER = PM_IER_WAKE;
NVIC_SetPriority(PM_IRQn,1);
NVIC_EnableIRQ(PM_IRQn);
config.action = PICOUART_ACTION_WAKEUP_ON_STARTBIT;
picouart_set_config(&dev_inst, &config);
bm_send_picouart_frame('A', 1);
bpm_sleep(BPM, BPM_SM_SLEEP_1);
config.action = PICOUART_ACTION_WAKEUP_ON_FULLFRAME;
picouart_set_config(&dev_inst, &config);
bm_send_picouart_frame('T', 5);
bpm_sleep(BPM, BPM_SM_SLEEP_3);
config.action = PICOUART_ACTION_WAKEUP_ON_FULLFRAME;
picouart_set_config(&dev_inst, &config);
bm_send_picouart_frame('M', 5);
bpm_sleep(BPM, BPM_SM_WAIT);
config.action = PICOUART_ACTION_WAKEUP_ON_MATCH;
config.match = 'L';
picouart_set_config(&dev_inst, &config);
bm_send_picouart_frame('L', 10);
bpm_sleep(BPM, BPM_SM_RET);
while(!picouart_is_data_ready(&dev_inst)) {
}
picouart_read(&dev_inst, &value);
test_assert_true(test, value == 'L', "Picouart wakeup not work!");
}
/*!
* \brief main function : do init and loop (poll if configured so)
*/
int main(void)
{
uint8_t key;
struct picouart_dev_inst dev_inst;
struct picouart_config config;
struct ast_config ast_conf;
/* Initialize the SAM system */
sysclk_init();
board_init();
/* Initialize the console uart */
configure_console();
/* Output example information */
printf("\r\n");
printf("-- PICOUART Example 1 --\r\n");
printf("-- %s\r\n", BOARD_NAME);
printf("-- Compiled: %s %s --\r\n", __DATE__, __TIME__);
printf("-- IMPORTANT: This example requires a board "
"monitor firmware version V1.3 or greater.\r\n");
/* Enable osc32 oscillator*/
if (!osc_is_ready(OSC_ID_OSC32)) {
osc_enable(OSC_ID_OSC32);
osc_wait_ready(OSC_ID_OSC32);
}
/* Disable all AST wake enable bits for safety since the AST is reset
only by a POR. */
ast_enable(AST);
ast_conf.mode = AST_COUNTER_MODE;
ast_conf.osc_type = AST_OSC_32KHZ;
ast_conf.psel = AST_PSEL_32KHZ_1HZ;
ast_conf.counter = 0;
ast_set_config(AST, &ast_conf);
ast_disable_wakeup(AST, AST_WAKEUP_ALARM);
ast_disable_wakeup(AST, AST_WAKEUP_PER);
ast_disable_wakeup(AST, AST_WAKEUP_OVF);
ast_disable(AST);
/* Config the push button */
config_buttons();
/* Configurate the USART to board monitor */
bm_init();
sysclk_enable_hsb_module(SYSCLK_PBA_BRIDGE);
sysclk_enable_peripheral_clock(BM_USART_USART);
/* Init the PICOUART */
picouart_get_config_defaults(&config);
picouart_init(&dev_inst, PICOUART, &config);
/* Enable the PICOUART */
picouart_enable(&dev_inst);
/* PICOUART and EIC can wakeup the device */
config_wakeup();
/* Display menu */
display_menu();
while (1) {
scanf("%c", (char *)&key);
switch (key) {
case 'h':
display_menu();
break;
case 's':
if (bm_flag) {
printf("Switch off the board monitor to wake up..\r\n");
bm_flag = false;
} else {
printf("Switch on the board monitor to wake up..\r\n");
bm_flag = true;
}
break;
case '0':
printf("Enter Sleep mode with start bit wakeup.\r\n");
config.action = PICOUART_ACTION_WAKEUP_ON_STARTBIT;
picouart_set_config(&dev_inst, &config);
if (bm_flag) {
printf("Board monitor will send frame after 3 seconds.\r\n");
bm_send_picouart_frame('A', 3000);
}
/* Wait for the printf operation to finish before
setting the device in a power save mode. */
delay_ms(30);
bpm_sleep(BPM, BPM_SM_SLEEP_2);
printf("--Exit Sleep mode.\r\n\r\n");
break;
case '1':
printf("Enter Retention mode with full frame wakeup.\r\n");
config.action = PICOUART_ACTION_WAKEUP_ON_FULLFRAME;
picouart_set_config(&dev_inst, &config);
if (bm_flag) {
printf("Board monitor will send frame after 3 seconds.\r\n");
bm_send_picouart_frame('T', 3000);
}
/* Wait for the printf operation to finish before
setting the device in a power save mode. */
delay_ms(30);
bpm_sleep(BPM, BPM_SM_RET);
printf("--Exit Retention mode.\r\n\r\n");
break;
case '2':
printf("Enter backup mode with character match wakeup.\r\n");
config.action = PICOUART_ACTION_WAKEUP_ON_MATCH;
config.match = 'L';
picouart_set_config(&dev_inst, &config);
if (bm_flag) {
printf("Board monitor will send frame after 3 seconds.\r\n");
bm_send_picouart_frame('L', 3000);
}
/* Wait for the printf operation to finish before
setting the device in a power save mode. */
delay_ms(30);
bpm_sleep(BPM, BPM_SM_BACKUP);
break;
default:
break;
}
}
}
