int main( void )
{
uint8_t tmpBuff[100];
uint32_t time = 0;
// Init clock and IO
bspInit();
// Init UART
bspUartInit();
// RF_Config();
Relay_Init();
Relay_Off(ROne);
LED_API.Init();
// Enable global interrupt
__bis_SR_register(GIE);
bspUartDataPut("Tra Quang Kieu", 14);
time = TWO_HOUR;
for(;;)
{
LED_API.Toggle(LED1);
// Relay_Toggle(ROne);
// Relay_Toggle(RTwo);
if (time == 0)
{
time = EIGHT_HOUR;
Relay_Toggle(ROne);
}
else
{
time--;
}
if (bspUartDataGet(tmpBuff, 10) > 0)
{
if (memcmp(tmpBuff, "on\n", 3) == 0)
{
Relay_On(ROne);
}
else if (memcmp(tmpBuff, "off\n", 4) == 0)
{
Relay_Off(ROne);
}
}
// bspUartDataPut("Tra Quang Kieu", 14);
__delay_cycles(16000000);
}
}
/**************************************************************************//**
* @brief Main function of example.
******************************************************************************/
void main(void)
{
uint8_t ui8KeyBm = 0;
uint_fast16_t ui16Cnt = 0;
uint8_t ui8Byte = APP_TX_BYTE;
//
// Initialize clocks and board I/O
//
bspInit(BSP_SYS_CLK_SPD);
//
// Set LED1 to indicate life
//
bspLedSet(BSP_LED_1);
//
// Initialize key driver
//
bspKeyInit(BSP_KEY_MODE_ISR);
bspKeyIntEnable(BSP_KEY_SELECT|BSP_KEY_UP);
//
// Initialize UART to USB MCU
//
bspUartBufInit(pui8TxBuf, sizeof(pui8TxBuf), pui8RxBuf, sizeof(pui8RxBuf));
//
// Application must register the UART interrupt handler
//
UARTIntRegister(BSP_UART_BASE, &appUartIsr);
//
// Open UART connection
//
if(bspUartOpen(eBaudRate115200) != BSP_UART_SUCCESS)
{
//
// Failed to initialize UART handler
//
bspAssert();
}
//
// Initialize SPI interface to LCD, configure LCD, and display information.
//
bspSpiInit(BSP_SPI_CLK_SPD);
lcdInit();
lcdBufferPrintStringAligned(0, "UART example", eLcdAlignCenter, eLcdPage0);
lcdBufferInvertPage(0, 0,127, eLcdPage0);
lcdBufferPrintString(0, "Baud rate :", 6, eLcdPage2);
lcdBufferPrintIntAligned(0, bspUartBaudRateGet(), eLcdAlignRight, eLcdPage2);
lcdBufferPrintString(0, "Format :", 6, eLcdPage3);
lcdBufferPrintStringAligned(0, "8-N-1", eLcdAlignRight, eLcdPage3);
lcdBufferPrintString(0, "Flow control:", 6, eLcdPage4);
lcdBufferPrintStringAligned(0, "No", eLcdAlignRight, eLcdPage4);
lcdBufferPrintStringAligned(0, "Transmit: UP key", eLcdAlignRight, eLcdPage6);
lcdBufferPrintStringAligned(0, "SELECT to toggle mode", eLcdAlignCenter, eLcdPage7);
lcdBufferInvertPage(0, 0,127, eLcdPage7);
lcdSendBuffer(0);
//
// Enable global interrupts
//
IntMasterEnable();
while(1)
{
ui8KeyBm = bspKeyPushed(BSP_KEY_ALL);
if(BSP_KEY_SELECT & ui8KeyBm)
{
//
// Change mode
//
bRepeaterMode ^= 1;
bspLedToggle(BSP_LED_3);
//
// Update LCD for the new mode
//
lcdBufferClearPart(0, 0,127, eLcdPage6, eLcdPage6);
if(bRepeaterMode)
{
lcdBufferPrintStringAligned(0, "Repeater mode",
eLcdAlignCenter, eLcdPage6);
}
else
{
lcdBufferPrintStringAligned(0, "Transmit: UP key",
eLcdAlignCenter, eLcdPage6);
}
lcdSendBufferPart(0, 0,127, eLcdPage6, eLcdPage6);
}
//
// Read data from UART RX buffer to application buffer
//
ui16Cnt = bspUartDataGet(pui8AppBuf, bspUartRxCharsAvail());
if(bRepeaterMode)
{
//
// Repeater mode
//
if(ui16Cnt)
{
//
// Send data from application buffer to UART TX buffer
//
bspUartDataPut(pui8AppBuf, ui16Cnt);
}
}
else
{
//
// Transmit mode
//
if(BSP_KEY_UP & ui8KeyBm)
{
//
// Transmit a single character
//
bspUartDataPut(&ui8Byte, 1);
}
}
}
}
