static void __init heroc_init(void)
{
int rc;
printk(KERN_INFO "heroc_init() revision=%d\n", system_rev);
config_gpios();
// gpio_request(HEROC_GPIO_H2W_POWER, "heroc_gpio_h2w_power");
// gpio_request(HEROC_GPIO_CABLE_IN2, "heroc_gpio_cable_in2");
gpio_request(HEROC_GPIO_AUD_EXTMIC_SEL, "heroc_gpio_aud_extmic_sel");
msm_hw_reset_hook = heroc_reset;
msm_acpu_clock_init(&heroc_clock_data);
perflock_init(&heroc_perflock_data);
#if defined(CONFIG_MSM_SERIAL_DEBUGGER)
if (!opt_disable_uart3)
msm_serial_debug_init(MSM_UART3_PHYS, INT_UART3,
&msm_device_uart3.dev, 1, INT_UART3_RX);
#endif
#ifdef CONFIG_SERIAL_MSM_HS
msm_device_uart_dm1.dev.platform_data = &msm_uart_dm1_pdata;
#endif
msm_device_hsusb.dev.platform_data = &msm_hsusb_pdata;
msm_init_pmic_vibrator(3000);
rc = heroc_init_mmc(system_rev);
if (rc)
printk(KERN_CRIT "%s: MMC init failure (%d)\n", __func__, rc);
msm_i2c_gpio_init();
msm_device_i2c.dev.platform_data = &heroc_i2c_device_data;
/* for (rc=0;rc<ARRAY_SIZE(i2c_devices);rc++){
if (!strcmp(i2c_devices[rc].type,AKM8973_I2C_NAME)){
if (!system_rev)
i2c_devices[rc].irq = 0x1E; //XA
else
i2c_devices[rc].irq = 0x1C;
}
}
if(system_rev < 2) {
microp_data.num_pins = ARRAY_SIZE(microp_pins_0);
microp_data.pin_config = microp_pins_0;
} */
i2c_register_board_info(0, i2c_devices, ARRAY_SIZE(i2c_devices));
platform_add_devices(devices, ARRAY_SIZE(devices));
clear_bluetooth_rx_irq_status();
// heroc_init_panel();
}
static void __init desirec_init(void)
{
int rc;
struct kobject *properties_kobj;
printk(KERN_INFO "%s() revision = %d\n", __func__, system_rev);
config_gpios();
if (system_rev > 0) {
/* We need to set this pin to 0 only once on power-up; we will
* not actually enable the chip until we apply power to it via
* vreg.
*/
gpio_direction_output(DESIREC_GPIO_CM3602_EN, 0);
/* disable power for cm3602 chip */
__capella_cm3602_power(0);
}
msm_hw_reset_hook = desirec_reset;
msm_acpu_clock_init(&desirec_clock_data);
perflock_init(&desirec_perflock_data);
#if defined(CONFIG_MSM_SERIAL_DEBUGGER)
if (!opt_disable_uart3)
msm_serial_debug_init(MSM_UART3_PHYS, INT_UART3,
&msm_device_uart3.dev, 1, INT_UART3_RX);
#endif
msm_add_devices();
clear_bluetooth_rx_irq_status();
#ifdef CONFIG_SERIAL_MSM_HS
msm_device_uart_dm1.dev.platform_data = &msm_uart_dm1_pdata;
msm_add_serial_devices(MSM_SERIAL_UART1DM);
#else
msm_add_serial_devices(MSM_SERIAL_UART1);
#endif
msm_add_serial_devices(MSM_SERIAL_UART3);
msm_add_usb_devices(desirec_phy_reset, desirec_phy_shutdown);
if (board_mcp_monodie())
msm_add_mem_devices(&pmem_mono_die_setting);
else
msm_add_mem_devices(&pmem_dual_die_setting);
msm_init_pmic_vibrator();
rc = desirec_init_mmc(system_rev);
if (rc)
printk(KERN_CRIT "%s: MMC init failure (%d)\n", __func__, rc);
properties_kobj = kobject_create_and_add("board_properties", NULL);
if (properties_kobj)
rc = sysfs_create_group(properties_kobj,
&desirec_properties_attr_group);
if (!properties_kobj || rc)
pr_err("failed to create board_properties\n");
msm_device_i2c.dev.platform_data = &desirec_i2c_device_data;
if (system_rev > 0) /*Aobve XB*/
platform_add_devices(devices, ARRAY_SIZE(devices));
else /* XA */
platform_add_devices(devices0, ARRAY_SIZE(devices0));
if (system_rev > 0) {
microp_data.ls_power = capella_cm3602_power;
if (system_rev >= 2) {
microp_data.num_pins = ARRAY_SIZE(microp_pins_2);
microp_data.pin_config = microp_pins_2;
}
}
i2c_register_board_info(0, i2c_devices, ARRAY_SIZE(i2c_devices));
/* r porting*/// i2c_register_board_info(0, &i2c_s5k3e2fx, 1);
}
