void rcc_clock_setup_hsi(const clock_scale_t *clock)
{
/* Enable internal high-speed oscillator. */
rcc_osc_on(HSI);
rcc_wait_for_osc_ready(HSI);
/* Select HSI as SYSCLK source. */
rcc_set_sysclk_source(RCC_CFGR_SW_SYSCLKSEL_HSICLK);
/*
* Set prescalers for AHB, ADC, ABP1, ABP2.
* Do this before touching the PLL (TODO: why?).
*/
rcc_set_hpre(clock->hpre);
rcc_set_ppre1(clock->ppre1);
rcc_set_ppre2(clock->ppre2);
rcc_peripheral_enable_clock(&RCC_APB1ENR, RCC_APB1ENR_PWREN);
pwr_set_vos_scale(clock->voltage_scale);
/* I guess this should be in the settings? */
flash_64bit_enable();
flash_prefetch_enable();
/* Configure flash settings. */
flash_set_ws(clock->flash_config);
/* Set the peripheral clock frequencies used. */
rcc_apb1_frequency = clock->apb1_frequency;
rcc_apb2_frequency = clock->apb2_frequency;
}
/**
* Set System Clock HSI48 at 48MHz
*/
void rcc_clock_setup_in_hsi48_out_48mhz(void)
{
rcc_osc_on(RCC_HSI48);
rcc_wait_for_osc_ready(RCC_HSI48);
rcc_set_hpre(RCC_CFGR_HPRE_NODIV);
rcc_set_ppre(RCC_CFGR_PPRE_NODIV);
flash_prefetch_enable();
flash_set_ws(FLASH_ACR_LATENCY_024_048MHZ);
rcc_set_sysclk_source(RCC_HSI48);
rcc_apb1_frequency = 48000000;
rcc_ahb_frequency = 48000000;
}
void rcc_clock_setup_pll(const struct rcc_clock_scale *clock)
{
/* Turn on the appropriate source for the PLL */
if (clock->pll_source == RCC_CFGR_PLLSRC_HSE_CLK) {
rcc_osc_on(RCC_HSE);
rcc_wait_for_osc_ready(RCC_HSE);
} else {
rcc_osc_on(RCC_HSI);
rcc_wait_for_osc_ready(RCC_HSI);
}
/*
* Set prescalers for AHB, ADC, ABP1, ABP2.
* Do this before touching the PLL (TODO: why?).
*/
rcc_set_hpre(clock->hpre);
rcc_set_ppre1(clock->ppre1);
rcc_set_ppre2(clock->ppre2);
rcc_periph_clock_enable(RCC_PWR);
pwr_set_vos_scale(clock->voltage_scale);
/* I guess this should be in the settings? */
flash_64bit_enable();
flash_prefetch_enable();
/* Configure flash settings. */
flash_set_ws(clock->flash_config);
rcc_set_pll_configuration(clock->pll_source, clock->pll_mul,
clock->pll_div);
/* Enable PLL oscillator and wait for it to stabilize. */
rcc_osc_on(RCC_PLL);
rcc_wait_for_osc_ready(RCC_PLL);
/* Select PLL as SYSCLK source. */
rcc_set_sysclk_source(RCC_CFGR_SW_SYSCLKSEL_PLLCLK);
/* Set the peripheral clock frequencies used. */
rcc_ahb_frequency = clock->ahb_frequency;
rcc_apb1_frequency = clock->apb1_frequency;
rcc_apb2_frequency = clock->apb2_frequency;
}
/**
* Setup clocks to run from PLL.
* The arguments provide the pll source, multipliers, dividers, all that's
* needed to establish a system clock.
* @param clock clock information structure
*/
void rcc_clock_setup_pll(const struct rcc_clock_scale *clock)
{
if (clock->pllsrc == RCC_CFGR_PLLSRC_HSE_PREDIV) {
rcc_osc_on(RCC_HSE);
rcc_wait_for_osc_ready(RCC_HSE);
} else {
rcc_osc_on(RCC_HSI);
rcc_wait_for_osc_ready(RCC_HSI);
}
rcc_osc_off(RCC_PLL);
rcc_usb_prescale_1_5();
if (clock->usbdiv1) {
rcc_usb_prescale_1();
}
rcc_wait_for_osc_not_ready(RCC_PLL);
rcc_set_pll_source(clock->pllsrc);
rcc_set_pll_multiplier(clock->pllmul);
rcc_set_prediv(clock->plldiv);
/* Enable PLL oscillator and wait for it to stabilize. */
rcc_osc_on(RCC_PLL);
rcc_wait_for_osc_ready(RCC_PLL);
/* Configure flash settings. */
flash_prefetch_enable();
flash_set_ws(clock->flash_waitstates);
rcc_set_hpre(clock->hpre);
rcc_set_ppre2(clock->ppre2);
rcc_set_ppre1(clock->ppre1);
/* Select PLL as SYSCLK source. */
rcc_set_sysclk_source(RCC_CFGR_SW_PLL);
/* Wait for PLL clock to be selected. */
rcc_wait_for_sysclk_status(RCC_PLL);
/* Set the peripheral clock frequencies used. */
rcc_ahb_frequency = clock->ahb_frequency;
rcc_apb1_frequency = clock->apb1_frequency;
rcc_apb2_frequency = clock->apb2_frequency;
}
/**
* Set System Clock PLL at 48MHz from HSI
*/
void rcc_clock_setup_in_hsi_out_48mhz(void)
{
rcc_osc_on(RCC_HSI);
rcc_wait_for_osc_ready(RCC_HSI);
rcc_set_sysclk_source(RCC_HSI);
rcc_set_hpre(RCC_CFGR_HPRE_NODIV);
rcc_set_ppre(RCC_CFGR_PPRE_NODIV);
flash_prefetch_enable();
flash_set_ws(FLASH_ACR_LATENCY_024_048MHZ);
/* 8MHz * 12 / 2 = 48MHz */
rcc_set_pll_multiplication_factor(RCC_CFGR_PLLMUL_MUL12);
rcc_set_pll_source(RCC_CFGR_PLLSRC_HSI_CLK_DIV2);
rcc_osc_on(RCC_PLL);
rcc_wait_for_osc_ready(RCC_PLL);
rcc_set_sysclk_source(RCC_PLL);
rcc_apb1_frequency = 48000000;
rcc_ahb_frequency = 48000000;
}
/**
* Set up sysclock with PLL from HSI16
* @param clock full struct with desired parameters
*/
void rcc_clock_setup_pll(const struct rcc_clock_scale *clock)
{
/* Turn on the appropriate source for the PLL */
if (clock->pll_source == RCC_CFGR_PLLSRC_HSE_CLK) {
rcc_osc_on(RCC_HSE);
rcc_wait_for_osc_ready(RCC_HSE);
} else {
rcc_osc_on(RCC_HSI16);
rcc_wait_for_osc_ready(RCC_HSI16);
}
rcc_set_hpre(clock->hpre);
rcc_set_ppre1(clock->ppre1);
rcc_set_ppre2(clock->ppre2);
rcc_periph_clock_enable(RCC_PWR);
pwr_set_vos_scale(clock->voltage_scale);
rcc_osc_off(RCC_PLL);
while (rcc_is_osc_ready(RCC_PLL));
flash_prefetch_enable();
flash_set_ws(clock->flash_waitstates);
/* Set up the PLL */
rcc_set_pll_multiplier(clock->pll_mul);
rcc_set_pll_divider(clock->pll_div);
rcc_osc_on(RCC_PLL);
rcc_wait_for_osc_ready(RCC_PLL);
rcc_set_sysclk_source(RCC_PLL);
/* Set the peripheral clock frequencies used. */
rcc_ahb_frequency = clock->ahb_frequency;
rcc_apb1_frequency = clock->apb1_frequency;
rcc_apb2_frequency = clock->apb2_frequency;
}
/**
* Switch sysclock to HSI with the given parameters.
* This should be usable from any point in time, but only if you have used
* library functions to manage clocks. It relies on the global
* @ref rcc_ahb_frequency to ensure that it reliably scales voltage up or down
* as appropriate.
* @param clock full struct with desired parameters
*/
void rcc_clock_setup_hsi(const struct rcc_clock_scale *clock)
{
/* Enable internal high-speed oscillator. */
rcc_osc_on(RCC_HSI);
rcc_periph_clock_enable(RCC_PWR);
/* I guess this should be in the settings? */
flash_64bit_enable();
flash_prefetch_enable();
/* Don't try and go to fast for a voltage range! */
if (clock->ahb_frequency > rcc_ahb_frequency) {
/* Going up, power up first */
pwr_set_vos_scale(clock->voltage_scale);
rcc_set_hpre(clock->hpre);
rcc_set_ppre1(clock->ppre1);
rcc_set_ppre2(clock->ppre2);
flash_set_ws(clock->flash_config);
} else {
/* going down, slow down before cutting power */
rcc_set_hpre(clock->hpre);
rcc_set_ppre1(clock->ppre1);
rcc_set_ppre2(clock->ppre2);
flash_set_ws(clock->flash_config);
pwr_set_vos_scale(clock->voltage_scale);
}
rcc_wait_for_osc_ready(RCC_HSI);
while (PWR_CSR & PWR_CSR_VOSF)
;
rcc_set_sysclk_source(RCC_CFGR_SW_SYSCLKSEL_HSICLK);
/* Set the peripheral clock frequencies used. */
rcc_ahb_frequency = clock->ahb_frequency;
rcc_apb1_frequency = clock->apb1_frequency;
rcc_apb2_frequency = clock->apb2_frequency;
}
void rcc_clock_setup_msi(const struct rcc_clock_scale *clock)
{
/* Enable internal multi-speed oscillator. */
uint32_t reg = RCC_ICSCR;
reg &= ~(RCC_ICSCR_MSIRANGE_MASK << RCC_ICSCR_MSIRANGE_SHIFT);
reg |= (clock->msi_range << RCC_ICSCR_MSIRANGE_SHIFT);
RCC_ICSCR = reg;
rcc_osc_on(RCC_MSI);
rcc_wait_for_osc_ready(RCC_MSI);
/* Select MSI as SYSCLK source. */
rcc_set_sysclk_source(RCC_CFGR_SW_SYSCLKSEL_MSICLK);
/*
* Set prescalers for AHB, ADC, ABP1, ABP2.
* Do this before touching the PLL (TODO: why?).
*/
rcc_set_hpre(clock->hpre);
rcc_set_ppre1(clock->ppre1);
rcc_set_ppre2(clock->ppre2);
rcc_peripheral_enable_clock(&RCC_APB1ENR, RCC_APB1ENR_PWREN);
pwr_set_vos_scale(clock->voltage_scale);
/* I guess this should be in the settings? */
flash_64bit_enable();
flash_prefetch_enable();
/* Configure flash settings. */
flash_set_ws(clock->flash_config);
/* Set the peripheral clock frequencies used. */
rcc_apb1_frequency = clock->apb1_frequency;
rcc_apb2_frequency = clock->apb2_frequency;
}
