void accel_gpio_init(void)
{
//gpio_pull_set(ACCEL_INT_PIN, GPIO_PULL_DOWN);
gpio_set_direction_field(ACCEL_INT_PIN, GPIO_INPUT);
gpio_set_interrupt(ACCEL_INT_PIN, GPIO_INT_RISING_EDGE);
gpio_enable_interrupt(ACCEL_INT_PIN);
//Accelerometer interrupt
//wakeup_by_gpio(ACCEL_INT_PIN, GPIO_WKUP_BY_HIGH); // does gpio_wakeup_config automatically
gpio_wakeup_config(ACCEL_INT_PIN, GPIO_WKUP_BY_HIGH); //sets direction to input automatically
}
void buttonIntTask(void *pvParameters)
{
printf("Waiting for button press interrupt on gpio %d...\r\n", gpio);
xQueueHandle *tsqueue = (xQueueHandle *)pvParameters;
gpio_set_interrupt(gpio, int_type);
uint32_t last = 0;
while(1) {
uint32_t button_ts;
xQueueReceive(*tsqueue, &button_ts, portMAX_DELAY);
button_ts *= portTICK_RATE_MS;
if(last < button_ts-200) {
printf("Button interrupt fired at %dms\r\n", button_ts);
last = button_ts;
// Blink the LED.
gpio_write(gpio_blink, 1);
vTaskDelay(1000 / portTICK_RATE_MS);
gpio_write(gpio_blink, 0);
vTaskDelay(1000 / portTICK_RATE_MS);
}
}
}
void interrupt_init(int pin, int changeType) {
gpio_enable(pin, GPIO_INPUT);
gpio_set_interrupt(pin, changeType);
}
/**
****************************************************************************************
* @brief BLE main function.
*
* This function is called right after the booting process has completed.
****************************************************************************************
*/
int main(void)
{
int ble_sleep_st, usr_sleep_st;
// DC-DC
dc_dc_enable(QN_DC_DC_ENABLE);
// QN platform initialization
#if QN_NVDS_WRITE
plf_init(QN_POWER_MODE, __XTAL, QN_32K_RCO, nvds_tmp_buf, NVDS_TMP_BUF_SIZE);
#else
plf_init(QN_POWER_MODE, __XTAL, QN_32K_RCO, NULL, 0);
#endif
#if (defined(QN_9020_B1) && (!QN_PMU_VOLTAGE))
disable_patch_b1();
#endif
// System initialization, user configuration
SystemInit();
// Profiles register
#if (QN_WORK_MODE != WORK_MODE_HCI)
prf_register();
#endif
// BLE stack initialization
// Notes:
// 1. When the chip works on Network Processor Mode, UART flow control signal is used to implement sleep mode.
// UART 's flow control feature shall be enabled. Enable this feature in the uart.c file.
// 2. Controller mode does not support sleep mode.
// 3. So far client example project does not support sleep mode. It will be implemented later.
// Check to go normal work mode or test mode.
// If the input of test control pin is low level, the program will enter into test mode, otherwise the program will
// enter into work mode which is defined in the user configuration file.
#if (defined(QN_TEST_CTRL_PIN))
if(gpio_read_pin(QN_TEST_CTRL_PIN) == GPIO_HIGH)
{
#endif
// Work mode defined in the usr_config.h
ble_init((enum WORK_MODE)QN_WORK_MODE, QN_HCI_PORT, QN_HCI_RD, QN_HCI_WR, ble_heap, BLE_HEAP_SIZE, QN_BLE_SLEEP);
#if (defined(QN_TEST_CTRL_PIN))
}
else
{
// Test mode (controller mode)
ble_init((enum WORK_MODE)WORK_MODE_HCI, QN_HCI_PORT, QN_HCI_RD, QN_HCI_WR, ble_heap, BLE_HEAP_SIZE, false);
// In the test mode, the program moniter test control pin. If the input of test control ping changes to low level,
// it means work mode should be switched to the mode defined in the user configuration file.
gpio_set_interrupt(QN_TEST_CTRL_PIN, GPIO_INT_HIGH_LEVEL);
gpio_enable_interrupt(QN_TEST_CTRL_PIN);
}
#endif
set_max_sleep_duration(QN_BLE_MAX_SLEEP_DUR);
// If QN902x works on wireless SoC mode, initialize APP task
#if (QN_WORK_MODE == WORK_MODE_SOC)
app_init();
#endif
usr_init();
sleep_init();
wakeup_by_sleep_timer(__32K_TYPE);
GLOBAL_INT_START();
while(1)
{
ke_schedule();
// Checks for sleep have to be done with interrupt disabled
GLOBAL_INT_DISABLE_WITHOUT_TUNER();
// Check whether the chip can enters sleep mode
//
// Chip enter sleep condition:
// +--------+--------+--------+--------+--------+
// | USR | | | | |
// | BLE | ACTIVE | IDLE | SLEEP | DEEP |
// +--------+--------+--------+--------+--------+
// | ACTIVE | active | active | active | active |
// | IDLE | active | idle | idle | idle |
// | SLEEP | active | idle | sleep | deep |
// +--------+--------+--------+--------+--------+
// Obtain the status of the user program
usr_sleep_st = usr_sleep();
// If the user program can be sleep or deep sleep then check ble status
if(usr_sleep_st != PM_ACTIVE)
{
// Obtain the status of ble sleep mode
ble_sleep_st = ble_sleep(usr_sleep_st);
// Check if the processor clock can be gated
if(((ble_sleep_st == PM_IDLE) || (usr_sleep_st == PM_IDLE))
&& (ble_sleep_st != PM_ACTIVE))
{
// Debug
//led_set(5, LED_OFF);
//led_set(4, LED_ON); // led4 is on when enter into gating mode
enter_sleep(SLEEP_CPU_CLK_OFF,
WAKEUP_BY_ALL_IRQ_SOURCE,
NULL);
// Debug
//led_set(4, LED_OFF);
//led_set(5, LED_ON); // led5 is on when enter into active mode
}
// Check if the processor can be power down
else if((ble_sleep_st == PM_SLEEP) && (usr_sleep_st == PM_SLEEP))
{
// Debug
//led_set(5, LED_OFF);
//led_set(3, LED_ON); // led3 is on when enter into sleep mode
enter_sleep(SLEEP_NORMAL,
(WAKEUP_BY_OSC_EN | WAKEUP_BY_GPIO),
sleep_cb);
// Debug
//led_set(3, LED_OFF);
//led_set(5, LED_ON); // led5 is on when enter into active mode
}
// Check if the system can be deep sleep
else if((ble_sleep_st == PM_SLEEP) && (usr_sleep_st == PM_DEEP_SLEEP))
{
// Debug
//led_set(5, LED_OFF);
//led_set(2, LED_ON); // led2 is on when enter into deep sleep mode
enter_sleep(SLEEP_DEEP,
WAKEUP_BY_GPIO,
sleep_cb);
// Debug
//led_set(2, LED_OFF);
//led_set(5, LED_ON); // led5 is on when enter into active mode
}
}
// Checks for sleep have to be done with interrupt disabled
GLOBAL_INT_RESTORE_WITHOUT_TUNER();
}
}
