static void gpsNewData(uint16_t c)
{
if (!gpsNewFrame(c)) {
return;
}
// new data received and parsed, we're in business
gpsData.lastLastMessage = gpsData.lastMessage;
gpsData.lastMessage = millis();
sensorsSet(SENSOR_GPS);
if (GPS_update == 1)
GPS_update = 0;
else
GPS_update = 1;
#if 0
debug[3] = GPS_update;
#endif
onGpsNewData();
}
static void gpsNewData(uint16_t c)
{
int axis;
static uint32_t nav_loopTimer;
int32_t dist;
int32_t dir;
int16_t speed;
if (gpsNewFrame(c)) {
// new data received and parsed, we're in business
gpsData.lastLastMessage = gpsData.lastMessage;
gpsData.lastMessage = millis();
sensorsSet(SENSOR_GPS);
if (GPS_update == 1)
GPS_update = 0;
else
GPS_update = 1;
if (f.GPS_FIX && GPS_numSat >= 5) {
if (!f.ARMED)
f.GPS_FIX_HOME = 0;
if (!f.GPS_FIX_HOME && f.ARMED)
GPS_reset_home_position();
// Apply moving average filter to GPS data
#if defined(GPS_FILTERING)
GPS_filter_index = (GPS_filter_index + 1) % GPS_FILTER_VECTOR_LENGTH;
for (axis = 0; axis < 2; axis++) {
GPS_read[axis] = GPS_coord[axis]; // latest unfiltered data is in GPS_latitude and GPS_longitude
GPS_degree[axis] = GPS_read[axis] / 10000000; // get the degree to assure the sum fits to the int32_t
// How close we are to a degree line ? its the first three digits from the fractions of degree
// later we use it to Check if we are close to a degree line, if yes, disable averaging,
fraction3[axis] = (GPS_read[axis] - GPS_degree[axis] * 10000000) / 10000;
GPS_filter_sum[axis] -= GPS_filter[axis][GPS_filter_index];
GPS_filter[axis][GPS_filter_index] = GPS_read[axis] - (GPS_degree[axis] * 10000000);
GPS_filter_sum[axis] += GPS_filter[axis][GPS_filter_index];
GPS_filtered[axis] = GPS_filter_sum[axis] / GPS_FILTER_VECTOR_LENGTH + (GPS_degree[axis] * 10000000);
if (nav_mode == NAV_MODE_POSHOLD) { // we use gps averaging only in poshold mode...
if (fraction3[axis] > 1 && fraction3[axis] < 999)
GPS_coord[axis] = GPS_filtered[axis];
}
}
#endif
// dTnav calculation
// Time for calculating x,y speed and navigation pids
dTnav = (float)(millis() - nav_loopTimer) / 1000.0f;
nav_loopTimer = millis();
// prevent runup from bad GPS
dTnav = min(dTnav, 1.0f);
// calculate distance and bearings for gui and other stuff continously - From home to copter
GPS_distance_cm_bearing(&GPS_coord[LAT], &GPS_coord[LON], &GPS_home[LAT], &GPS_home[LON], &dist, &dir);
GPS_distanceToHome = dist / 100;
GPS_directionToHome = dir / 100;
if (!f.GPS_FIX_HOME) { // If we don't have home set, do not display anything
GPS_distanceToHome = 0;
GPS_directionToHome = 0;
}
// calculate the current velocity based on gps coordinates continously to get a valid speed at the moment when we start navigating
GPS_calc_velocity();
if (f.GPS_HOLD_MODE || f.GPS_HOME_MODE) { // ok we are navigating
// do gps nav calculations here, these are common for nav and poshold
GPS_distance_cm_bearing(&GPS_coord[LAT], &GPS_coord[LON], &GPS_WP[LAT], &GPS_WP[LON], &wp_distance, &target_bearing);
GPS_calc_location_error(&GPS_WP[LAT], &GPS_WP[LON], &GPS_coord[LAT], &GPS_coord[LON]);
switch (nav_mode) {
case NAV_MODE_POSHOLD:
// Desired output is in nav_lat and nav_lon where 1deg inclination is 100
GPS_calc_poshold();
break;
case NAV_MODE_WP:
speed = GPS_calc_desired_speed(cfg.nav_speed_max, NAV_SLOW_NAV); // slow navigation
// use error as the desired rate towards the target
// Desired output is in nav_lat and nav_lon where 1deg inclination is 100
GPS_calc_nav_rate(speed);
// Tail control
if (cfg.nav_controls_heading) {
if (NAV_TAIL_FIRST) {
magHold = wrap_18000(nav_bearing - 18000) / 100;
} else {
magHold = nav_bearing / 100;
}
}
// Are we there yet ?(within x meters of the destination)
if ((wp_distance <= cfg.gps_wp_radius) || check_missed_wp()) { // if yes switch to poshold mode
nav_mode = NAV_MODE_POSHOLD;
if (NAV_SET_TAKEOFF_HEADING) {
magHold = nav_takeoff_bearing;
}
}
break;
}
} //end of gps calcs
}
}
}
