bool sensorsAutodetect(sensorAlignmentConfig_t *sensorAlignmentConfig,
uint8_t accHardwareToUse,
uint8_t magHardwareToUse,
uint8_t baroHardwareToUse,
int16_t magDeclinationFromConfig,
uint8_t gyroLpf,
uint8_t gyroSyncDenominator)
{
memset(&acc, 0, sizeof(acc));
memset(&gyro, 0, sizeof(gyro));
#if defined(USE_GYRO_MPU6050) || defined(USE_GYRO_MPU3050) || defined(USE_GYRO_MPU6500) || defined(USE_GYRO_SPI_MPU6500) || defined(USE_GYRO_SPI_MPU6000) || defined(USE_ACC_MPU6050) || defined(USE_GYRO_SPI_MPU9250)
const extiConfig_t *extiConfig = selectMPUIntExtiConfig();
mpuDetectionResult_t *mpuDetectionResult = detectMpu(extiConfig);
UNUSED(mpuDetectionResult);
#endif
if (!detectGyro()) {
return false;
}
detectAcc(accHardwareToUse);
detectBaro(baroHardwareToUse);
// Now time to init things, acc first
if (sensors(SENSOR_ACC)) {
acc.acc_1G = 256; // set default
acc.init(&acc);
}
// this is safe because either mpu6050 or mpu3050 or lg3d20 sets it, and in case of fail, we never get here.
gyro.targetLooptime = gyroSetSampleRate(gyroLpf, gyroSyncDenominator); // Set gyro sample rate before initialisation
gyro.init(gyroLpf);
gyroInit();
detectMag(magHardwareToUse);
reconfigureAlignment(sensorAlignmentConfig);
// FIXME extract to a method to reduce dependencies, maybe move to sensors_compass.c
if (sensors(SENSOR_MAG)) {
// calculate magnetic declination
const int16_t deg = magDeclinationFromConfig / 100;
const int16_t min = magDeclinationFromConfig % 100;
magneticDeclination = (deg + ((float)min * (1.0f / 60.0f))) * 10; // heading is in 0.1deg units
} else {
magneticDeclination = 0.0f; // TODO investigate if this is actually needed if there is no mag sensor or if the value stored in the config should be used.
}
return true;
}
static void gyroInitSensor(gyroSensor_t *gyroSensor, const gyroDeviceConfig_t *config)
{
gyroSensor->gyroDebugAxis = gyroConfig()->gyro_filter_debug_axis;
gyroSensor->gyroDev.gyro_high_fsr = gyroConfig()->gyro_high_fsr;
gyroSensor->gyroDev.gyroAlign = config->align;
gyroSensor->gyroDev.mpuIntExtiTag = config->extiTag;
// Must set gyro targetLooptime before gyroDev.init and initialisation of filters
gyro.targetLooptime = gyroSetSampleRate(&gyroSensor->gyroDev, gyroConfig()->gyro_hardware_lpf, gyroConfig()->gyro_sync_denom);
gyroSensor->gyroDev.hardware_lpf = gyroConfig()->gyro_hardware_lpf;
gyroSensor->gyroDev.initFn(&gyroSensor->gyroDev);
// As new gyros are supported, be sure to add them below based on whether they are subject to the overflow/inversion bug
// Any gyro not explicitly defined will default to not having built-in overflow protection as a safe alternative.
switch (gyroSensor->gyroDev.gyroHardware) {
case GYRO_NONE: // Won't ever actually get here, but included to account for all gyro types
case GYRO_DEFAULT:
case GYRO_FAKE:
case GYRO_MPU6050:
case GYRO_L3G4200D:
case GYRO_MPU3050:
case GYRO_L3GD20:
case GYRO_BMI160:
case GYRO_MPU6000:
case GYRO_MPU6500:
case GYRO_MPU9250:
gyroSensor->gyroDev.gyroHasOverflowProtection = true;
break;
case GYRO_ICM20601:
case GYRO_ICM20602:
case GYRO_ICM20608G:
case GYRO_ICM20649: // we don't actually know if this is affected, but as there are currently no flight controllers using it we err on the side of caution
case GYRO_ICM20689:
gyroSensor->gyroDev.gyroHasOverflowProtection = false;
break;
default:
gyroSensor->gyroDev.gyroHasOverflowProtection = false; // default catch for newly added gyros until proven to be unaffected
break;
}
gyroInitSensorFilters(gyroSensor);
#ifdef USE_GYRO_DATA_ANALYSE
gyroDataAnalyseStateInit(&gyroSensor->gyroAnalyseState, gyro.targetLooptime);
#endif
}
void init(void)
{
drv_pwm_config_t pwm_params;
printfSupportInit();
initEEPROM();
ensureEEPROMContainsValidData();
readEEPROM();
systemState |= SYSTEM_STATE_CONFIG_LOADED;
#ifdef STM32F303
// start fpu
SCB->CPACR = (0x3 << (10*2)) | (0x3 << (11*2));
#endif
#ifdef STM32F303xC
SetSysClock();
#endif
#ifdef STM32F10X
// Configure the System clock frequency, HCLK, PCLK2 and PCLK1 prescalers
// Configure the Flash Latency cycles and enable prefetch buffer
SetSysClock(systemConfig()->emf_avoidance);
#endif
i2cSetOverclock(systemConfig()->i2c_highspeed);
systemInit();
#ifdef USE_HARDWARE_REVISION_DETECTION
detectHardwareRevision();
#endif
// Latch active features to be used for feature() in the remainder of init().
latchActiveFeatures();
#ifdef ALIENFLIGHTF3
if (hardwareRevision == AFF3_REV_1) {
ledInit(false);
} else {
ledInit(true);
}
#else
ledInit(false);
#endif
#ifdef BEEPER
beeperConfig_t beeperConfig = {
.gpioPeripheral = BEEP_PERIPHERAL,
.gpioPin = BEEP_PIN,
.gpioPort = BEEP_GPIO,
#ifdef BEEPER_INVERTED
.gpioMode = Mode_Out_PP,
.isInverted = true
#else
.gpioMode = Mode_Out_OD,
.isInverted = false
#endif
};
#ifdef NAZE
if (hardwareRevision >= NAZE32_REV5) {
// naze rev4 and below used opendrain to PNP for buzzer. Rev5 and above use PP to NPN.
beeperConfig.gpioMode = Mode_Out_PP;
beeperConfig.isInverted = true;
}
#endif
beeperInit(&beeperConfig);
#endif
#ifdef BUTTONS
buttonsInit();
if (!isMPUSoftReset()) {
buttonsHandleColdBootButtonPresses();
}
#endif
#ifdef SPEKTRUM_BIND
if (feature(FEATURE_RX_SERIAL)) {
switch (rxConfig()->serialrx_provider) {
case SERIALRX_SPEKTRUM1024:
case SERIALRX_SPEKTRUM2048:
// Spektrum satellite binding if enabled on startup.
// Must be called before that 100ms sleep so that we don't lose satellite's binding window after startup.
// The rest of Spektrum initialization will happen later - via spektrumInit()
spektrumBind(rxConfig());
break;
}
}
#endif
delay(100);
timerInit(); // timer must be initialized before any channel is allocated
dmaInit();
serialInit(feature(FEATURE_SOFTSERIAL));
mixerInit(customMotorMixer(0));
#ifdef USE_SERVOS
mixerInitServos(customServoMixer(0));
#endif
memset(&pwm_params, 0, sizeof(pwm_params));
#ifdef SONAR
const sonarHardware_t *sonarHardware = NULL;
if (feature(FEATURE_SONAR)) {
sonarHardware = sonarGetHardwareConfiguration(batteryConfig()->currentMeterType);
sonarGPIOConfig_t sonarGPIOConfig = {
.gpio = SONAR_GPIO,
.triggerPin = sonarHardware->echo_pin,
.echoPin = sonarHardware->trigger_pin,
};
pwm_params.sonarGPIOConfig = &sonarGPIOConfig;
}
#endif
// when using airplane/wing mixer, servo/motor outputs are remapped
if (mixerConfig()->mixerMode == MIXER_AIRPLANE || mixerConfig()->mixerMode == MIXER_FLYING_WING || mixerConfig()->mixerMode == MIXER_CUSTOM_AIRPLANE)
pwm_params.airplane = true;
else
pwm_params.airplane = false;
#if defined(USE_UART2) && defined(STM32F10X)
pwm_params.useUART2 = doesConfigurationUsePort(SERIAL_PORT_UART2);
#endif
#if defined(USE_UART3)
pwm_params.useUART3 = doesConfigurationUsePort(SERIAL_PORT_UART3);
#endif
#if defined(USE_UART4)
pwm_params.useUART4 = doesConfigurationUsePort(SERIAL_PORT_UART4);
#endif
#if defined(USE_UART5)
pwm_params.useUART5 = doesConfigurationUsePort(SERIAL_PORT_UART5);
#endif
pwm_params.useVbat = feature(FEATURE_VBAT);
pwm_params.useSoftSerial = feature(FEATURE_SOFTSERIAL);
pwm_params.useParallelPWM = feature(FEATURE_RX_PARALLEL_PWM);
pwm_params.useRSSIADC = feature(FEATURE_RSSI_ADC);
pwm_params.useCurrentMeterADC = (
feature(FEATURE_CURRENT_METER)
&& batteryConfig()->currentMeterType == CURRENT_SENSOR_ADC
);
pwm_params.useLEDStrip = feature(FEATURE_LED_STRIP);
pwm_params.usePPM = feature(FEATURE_RX_PPM);
pwm_params.useSerialRx = feature(FEATURE_RX_SERIAL);
#ifdef SONAR
pwm_params.useSonar = feature(FEATURE_SONAR);
#endif
#ifdef USE_SERVOS
pwm_params.useServos = isMixerUsingServos();
pwm_params.useChannelForwarding = feature(FEATURE_CHANNEL_FORWARDING);
pwm_params.servoCenterPulse = motorAndServoConfig()->servoCenterPulse;
pwm_params.servoPwmRate = motorAndServoConfig()->servo_pwm_rate;
#endif
pwm_params.useOneshot = feature(FEATURE_ONESHOT125);
pwm_params.motorPwmRate = motorAndServoConfig()->motor_pwm_rate;
pwm_params.idlePulse = motorAndServoConfig()->mincommand;
if (feature(FEATURE_3D))
pwm_params.idlePulse = motor3DConfig()->neutral3d;
if (pwm_params.motorPwmRate > 500)
pwm_params.idlePulse = 0; // brushed motors
pwmRxInit();
// pwmInit() needs to be called as soon as possible for ESC compatibility reasons
pwmIOConfiguration_t *pwmIOConfiguration = pwmInit(&pwm_params);
mixerUsePWMIOConfiguration(pwmIOConfiguration);
#ifdef DEBUG_PWM_CONFIGURATION
debug[2] = pwmIOConfiguration->pwmInputCount;
debug[3] = pwmIOConfiguration->ppmInputCount;
#endif
if (!feature(FEATURE_ONESHOT125))
motorControlEnable = true;
systemState |= SYSTEM_STATE_MOTORS_READY;
#ifdef INVERTER
initInverter();
#endif
#ifdef USE_SPI
spiInit(SPI1);
spiInit(SPI2);
#ifdef STM32F303xC
#ifdef ALIENFLIGHTF3
if (hardwareRevision == AFF3_REV_2) {
spiInit(SPI3);
}
#else
spiInit(SPI3);
#endif
#endif
#endif
#ifdef USE_HARDWARE_REVISION_DETECTION
updateHardwareRevision();
#endif
#if defined(NAZE)
if (hardwareRevision == NAZE32_SP) {
serialRemovePort(SERIAL_PORT_SOFTSERIAL2);
} else {
serialRemovePort(SERIAL_PORT_UART3);
}
#endif
#if defined(SPRACINGF3) && defined(SONAR) && defined(USE_SOFTSERIAL2)
if (feature(FEATURE_SONAR) && feature(FEATURE_SOFTSERIAL)) {
serialRemovePort(SERIAL_PORT_SOFTSERIAL2);
}
#endif
#if defined(SPRACINGF3MINI) && defined(SONAR) && defined(USE_SOFTSERIAL1)
if (feature(FEATURE_SONAR) && feature(FEATURE_SOFTSERIAL)) {
serialRemovePort(SERIAL_PORT_SOFTSERIAL1);
}
#endif
#ifdef USE_I2C
#if defined(NAZE)
if (hardwareRevision != NAZE32_SP) {
i2cInit(I2C_DEVICE);
} else {
if (!doesConfigurationUsePort(SERIAL_PORT_UART3)) {
i2cInit(I2C_DEVICE);
}
}
#elif defined(CC3D)
if (!doesConfigurationUsePort(SERIAL_PORT_UART3)) {
i2cInit(I2C_DEVICE);
}
#else
i2cInit(I2C_DEVICE);
#endif
#endif
#ifdef USE_ADC
drv_adc_config_t adc_params;
adc_params.enableVBat = feature(FEATURE_VBAT);
adc_params.enableRSSI = feature(FEATURE_RSSI_ADC);
adc_params.enableCurrentMeter = feature(FEATURE_CURRENT_METER);
adc_params.enableExternal1 = false;
#ifdef OLIMEXINO
adc_params.enableExternal1 = true;
#endif
#ifdef NAZE
// optional ADC5 input on rev.5 hardware
adc_params.enableExternal1 = (hardwareRevision >= NAZE32_REV5);
#endif
adcInit(&adc_params);
#endif
initBoardAlignment();
#ifdef DISPLAY
if (feature(FEATURE_DISPLAY)) {
displayInit();
}
#endif
gyroSetSampleRate(imuConfig()->looptime, gyroConfig()->gyro_lpf, imuConfig()->gyroSync, imuConfig()->gyroSyncDenominator); // Set gyro sampling rate divider before initialization
if (!sensorsAutodetect()) {
// if gyro was not detected due to whatever reason, we give up now.
failureMode(FAILURE_MISSING_ACC);
}
systemState |= SYSTEM_STATE_SENSORS_READY;
flashLedsAndBeep();
#ifdef USE_SERVOS
mixerInitialiseServoFiltering(targetLooptime);
#endif
#ifdef MAG
if (sensors(SENSOR_MAG))
compassInit();
#endif
imuInit();
mspInit();
mspSerialInit();
#ifdef USE_CLI
cliInit();
#endif
failsafeInit();
rxInit(modeActivationProfile()->modeActivationConditions);
#ifdef GPS
if (feature(FEATURE_GPS)) {
gpsInit();
navigationInit(pidProfile());
}
#endif
#ifdef SONAR
if (feature(FEATURE_SONAR)) {
sonarInit(sonarHardware);
}
#endif
#ifdef LED_STRIP
ledStripInit();
if (feature(FEATURE_LED_STRIP)) {
ledStripEnable();
}
#endif
#ifdef TELEMETRY
if (feature(FEATURE_TELEMETRY)) {
telemetryInit();
}
#endif
#ifdef USB_CABLE_DETECTION
usbCableDetectInit();
#endif
#ifdef TRANSPONDER
if (feature(FEATURE_TRANSPONDER)) {
transponderInit(transponderConfig()->data);
transponderEnable();
transponderStartRepeating();
systemState |= SYSTEM_STATE_TRANSPONDER_ENABLED;
}
#endif
#ifdef USE_FLASHFS
#ifdef NAZE
if (hardwareRevision == NAZE32_REV5) {
m25p16_init();
}
#elif defined(USE_FLASH_M25P16)
m25p16_init();
#endif
flashfsInit();
#endif
#ifdef USE_SDCARD
bool sdcardUseDMA = false;
sdcardInsertionDetectInit();
#ifdef SDCARD_DMA_CHANNEL_TX
#if defined(LED_STRIP) && defined(WS2811_DMA_CHANNEL)
// Ensure the SPI Tx DMA doesn't overlap with the led strip
sdcardUseDMA = !feature(FEATURE_LED_STRIP) || SDCARD_DMA_CHANNEL_TX != WS2811_DMA_CHANNEL;
#else
sdcardUseDMA = true;
#endif
#endif
sdcard_init(sdcardUseDMA);
afatfs_init();
#endif
#ifdef BLACKBOX
initBlackbox();
#endif
if (mixerConfig()->mixerMode == MIXER_GIMBAL) {
accSetCalibrationCycles(CALIBRATING_ACC_CYCLES);
}
gyroSetCalibrationCycles(CALIBRATING_GYRO_CYCLES);
#ifdef BARO
baroSetCalibrationCycles(CALIBRATING_BARO_CYCLES);
#endif
// start all timers
// TODO - not implemented yet
timerStart();
ENABLE_STATE(SMALL_ANGLE);
DISABLE_ARMING_FLAG(PREVENT_ARMING);
#ifdef SOFTSERIAL_LOOPBACK
// FIXME this is a hack, perhaps add a FUNCTION_LOOPBACK to support it properly
loopbackPort = (serialPort_t*)&(softSerialPorts[0]);
if (!loopbackPort->vTable) {
loopbackPort = openSoftSerial(0, NULL, 19200, SERIAL_NOT_INVERTED);
}
serialPrint(loopbackPort, "LOOPBACK\r\n");
#endif
// Now that everything has powered up the voltage and cell count be determined.
if (feature(FEATURE_VBAT | FEATURE_CURRENT_METER))
batteryInit();
#ifdef DISPLAY
if (feature(FEATURE_DISPLAY)) {
#ifdef USE_OLED_GPS_DEBUG_PAGE_ONLY
displayShowFixedPage(PAGE_GPS);
#else
displayResetPageCycling();
displayEnablePageCycling();
#endif
}
#endif
#ifdef CJMCU
LED2_ON;
#endif
// Latch active features AGAIN since some may be modified by init().
latchActiveFeatures();
motorControlEnable = true;
systemState |= SYSTEM_STATE_READY;
}
#ifdef SOFTSERIAL_LOOPBACK
void processLoopback(void) {
if (loopbackPort) {
uint8_t bytesWaiting;
while ((bytesWaiting = serialRxBytesWaiting(loopbackPort))) {
uint8_t b = serialRead(loopbackPort);
serialWrite(loopbackPort, b);
};
}
}
#else
#define processLoopback()
#endif
int main(void) {
init();
// Setup scheduler
schedulerInit();
setTaskEnabled(TASK_GYROPID, true);
rescheduleTask(TASK_GYROPID, imuConfig()->gyroSync ? targetLooptime - INTERRUPT_WAIT_TIME : targetLooptime);
setTaskEnabled(TASK_ACCEL, sensors(SENSOR_ACC));
setTaskEnabled(TASK_SERIAL, true);
#ifdef BEEPER
setTaskEnabled(TASK_BEEPER, true);
#endif
setTaskEnabled(TASK_BATTERY, feature(FEATURE_VBAT) || feature(FEATURE_CURRENT_METER));
setTaskEnabled(TASK_RX, true);
#ifdef GPS
setTaskEnabled(TASK_GPS, feature(FEATURE_GPS));
#endif
#ifdef MAG
setTaskEnabled(TASK_COMPASS, sensors(SENSOR_MAG));
#if defined(MPU6500_SPI_INSTANCE) && defined(USE_MAG_AK8963)
// fixme temporary solution for AK6983 via slave I2C on MPU9250
rescheduleTask(TASK_COMPASS, 1000000 / 40);
#endif
#endif
#ifdef BARO
setTaskEnabled(TASK_BARO, sensors(SENSOR_BARO));
#endif
#ifdef SONAR
setTaskEnabled(TASK_SONAR, sensors(SENSOR_SONAR));
#endif
#if defined(BARO) || defined(SONAR)
setTaskEnabled(TASK_ALTITUDE, sensors(SENSOR_BARO) || sensors(SENSOR_SONAR));
#endif
#ifdef DISPLAY
setTaskEnabled(TASK_DISPLAY, feature(FEATURE_DISPLAY));
#endif
#ifdef TELEMETRY
setTaskEnabled(TASK_TELEMETRY, feature(FEATURE_TELEMETRY));
#endif
#ifdef LED_STRIP
setTaskEnabled(TASK_LEDSTRIP, feature(FEATURE_LED_STRIP));
#endif
#ifdef TRANSPONDER
setTaskEnabled(TASK_TRANSPONDER, feature(FEATURE_TRANSPONDER));
#endif
while (true) {
scheduler();
processLoopback();
}
}
void HardFault_Handler(void)
{
// fall out of the sky
uint8_t requiredStateForMotors = SYSTEM_STATE_CONFIG_LOADED | SYSTEM_STATE_MOTORS_READY;
if ((systemState & requiredStateForMotors) == requiredStateForMotors) {
stopMotors();
}
#ifdef TRANSPONDER
// prevent IR LEDs from burning out.
uint8_t requiredStateForTransponder = SYSTEM_STATE_CONFIG_LOADED | SYSTEM_STATE_TRANSPONDER_ENABLED;
if ((systemState & requiredStateForTransponder) == requiredStateForTransponder) {
transponderIrDisable();
}
#endif
while (1);
}
void init(void)
{
printfSupportInit();
initEEPROM();
ensureEEPROMContainsValidData();
readEEPROM();
systemState |= SYSTEM_STATE_CONFIG_LOADED;
// initialize IO (needed for all IO operations)
IOInitGlobal();
#ifdef STM32F303
// start fpu
SCB->CPACR = (0x3 << (10*2)) | (0x3 << (11*2));
#endif
#ifdef STM32F303xC
SetSysClock();
#endif
#ifdef STM32F10X
// Configure the System clock frequency, HCLK, PCLK2 and PCLK1 prescalers
// Configure the Flash Latency cycles and enable prefetch buffer
SetSysClock(masterConfig.emf_avoidance);
#endif
i2cSetOverclock(masterConfig.i2c_overclock);
#ifdef USE_HARDWARE_REVISION_DETECTION
detectHardwareRevision();
#endif
systemInit();
// Latch active features to be used for feature() in the remainder of init().
latchActiveFeatures();
#ifdef ALIENFLIGHTF3
ledInit(hardwareRevision == AFF3_REV_1 ? false : true);
#else
ledInit(false);
#endif
#ifdef SPEKTRUM_BIND
if (feature(FEATURE_RX_SERIAL)) {
switch (masterConfig.rxConfig.serialrx_provider) {
case SERIALRX_SPEKTRUM1024:
case SERIALRX_SPEKTRUM2048:
// Spektrum satellite binding if enabled on startup.
// Must be called before that 100ms sleep so that we don't lose satellite's binding window after startup.
// The rest of Spektrum initialization will happen later - via spektrumInit()
spektrumBind(&masterConfig.rxConfig);
break;
}
}
#endif
delay(500);
timerInit(); // timer must be initialized before any channel is allocated
serialInit(&masterConfig.serialConfig, feature(FEATURE_SOFTSERIAL));
#ifdef USE_SERVOS
mixerInit(masterConfig.mixerMode, masterConfig.customMotorMixer, masterConfig.customServoMixer);
#else
mixerInit(masterConfig.mixerMode, masterConfig.customMotorMixer);
#endif
drv_pwm_config_t pwm_params;
memset(&pwm_params, 0, sizeof(pwm_params));
#ifdef SONAR
if (feature(FEATURE_SONAR)) {
const sonarHcsr04Hardware_t *sonarHardware = sonarGetHardwareConfiguration(masterConfig.batteryConfig.currentMeterType);
if (sonarHardware) {
pwm_params.useSonar = true;
pwm_params.sonarIOConfig.triggerTag = sonarHardware->triggerTag;
pwm_params.sonarIOConfig.echoTag = sonarHardware->echoTag;
}
}
#endif
// when using airplane/wing mixer, servo/motor outputs are remapped
if (masterConfig.mixerMode == MIXER_AIRPLANE || masterConfig.mixerMode == MIXER_FLYING_WING || masterConfig.mixerMode == MIXER_CUSTOM_AIRPLANE)
pwm_params.airplane = true;
else
pwm_params.airplane = false;
#if defined(USE_USART2) && defined(STM32F10X)
pwm_params.useUART2 = doesConfigurationUsePort(SERIAL_PORT_USART2);
#endif
#ifdef STM32F303xC
pwm_params.useUART3 = doesConfigurationUsePort(SERIAL_PORT_USART3);
#endif
pwm_params.useVbat = feature(FEATURE_VBAT);
pwm_params.useSoftSerial = feature(FEATURE_SOFTSERIAL);
pwm_params.useParallelPWM = feature(FEATURE_RX_PARALLEL_PWM);
pwm_params.useRSSIADC = feature(FEATURE_RSSI_ADC);
pwm_params.useCurrentMeterADC = feature(FEATURE_CURRENT_METER)
&& masterConfig.batteryConfig.currentMeterType == CURRENT_SENSOR_ADC;
pwm_params.useLEDStrip = feature(FEATURE_LED_STRIP);
pwm_params.usePPM = feature(FEATURE_RX_PPM);
pwm_params.useSerialRx = feature(FEATURE_RX_SERIAL);
#ifdef USE_SERVOS
pwm_params.useServos = isServoOutputEnabled();
pwm_params.useChannelForwarding = feature(FEATURE_CHANNEL_FORWARDING);
pwm_params.servoCenterPulse = masterConfig.escAndServoConfig.servoCenterPulse;
pwm_params.servoPwmRate = masterConfig.servo_pwm_rate;
#endif
pwm_params.useOneshot = feature(FEATURE_ONESHOT125);
pwm_params.motorPwmRate = masterConfig.motor_pwm_rate;
pwm_params.idlePulse = masterConfig.escAndServoConfig.mincommand;
if (feature(FEATURE_3D))
pwm_params.idlePulse = masterConfig.flight3DConfig.neutral3d;
if (pwm_params.motorPwmRate > 500)
pwm_params.idlePulse = 0; // brushed motors
#ifndef SKIP_RX_PWM_PPM
pwmRxInit(masterConfig.inputFilteringMode);
#endif
// pwmInit() needs to be called as soon as possible for ESC compatibility reasons
pwmInit(&pwm_params);
mixerUsePWMIOConfiguration();
if (!feature(FEATURE_ONESHOT125))
motorControlEnable = true;
systemState |= SYSTEM_STATE_MOTORS_READY;
#ifdef BEEPER
beeperConfig_t beeperConfig = {
.ioTag = IO_TAG(BEEPER),
#ifdef BEEPER_INVERTED
.isOD = false,
.isInverted = true
#else
.isOD = true,
.isInverted = false
#endif
};
#ifdef NAZE
if (hardwareRevision >= NAZE32_REV5) {
// naze rev4 and below used opendrain to PNP for buzzer. Rev5 and above use PP to NPN.
beeperConfig.isOD = false;
beeperConfig.isInverted = true;
}
#endif
beeperInit(&beeperConfig);
#endif
#ifdef INVERTER
initInverter();
#endif
#ifdef USE_SPI
spiInit(SPI1);
spiInit(SPI2);
#endif
#ifdef USE_HARDWARE_REVISION_DETECTION
updateHardwareRevision();
#endif
#if defined(NAZE)
if (hardwareRevision == NAZE32_SP) {
serialRemovePort(SERIAL_PORT_SOFTSERIAL2);
} else {
serialRemovePort(SERIAL_PORT_USART3);
}
#endif
#if defined(SPRACINGF3) && defined(SONAR) && defined(USE_SOFTSERIAL2)
if (feature(FEATURE_SONAR) && feature(FEATURE_SOFTSERIAL)) {
serialRemovePort(SERIAL_PORT_SOFTSERIAL2);
}
#endif
#if defined(FURYF3) && defined(SONAR) && defined(USE_SOFTSERIAL1)
if (feature(FEATURE_SONAR) && feature(FEATURE_SOFTSERIAL)) {
serialRemovePort(SERIAL_PORT_SOFTSERIAL1);
}
#endif
#ifdef USE_I2C
#if defined(NAZE)
if (hardwareRevision != NAZE32_SP) {
i2cInit(I2C_DEVICE);
} else {
if (!doesConfigurationUsePort(SERIAL_PORT_USART3)) {
i2cInit(I2C_DEVICE);
}
}
#elif defined(CC3D)
if (!doesConfigurationUsePort(SERIAL_PORT_USART3)) {
i2cInit(I2C_DEVICE);
}
#else
i2cInit(I2C_DEVICE);
#endif
#endif
#ifdef USE_ADC
drv_adc_config_t adc_params;
adc_params.enableVBat = feature(FEATURE_VBAT);
adc_params.enableRSSI = feature(FEATURE_RSSI_ADC);
adc_params.enableCurrentMeter = feature(FEATURE_CURRENT_METER);
adc_params.enableExternal1 = false;
#ifdef OLIMEXINO
adc_params.enableExternal1 = true;
#endif
#ifdef NAZE
// optional ADC5 input on rev.5 hardware
adc_params.enableExternal1 = (hardwareRevision >= NAZE32_REV5);
#endif
adcInit(&adc_params);
#endif
initBoardAlignment(&masterConfig.boardAlignment);
#ifdef DISPLAY
if (feature(FEATURE_DISPLAY)) {
displayInit(&masterConfig.rxConfig);
}
#endif
#ifdef GPS
if (feature(FEATURE_GPS)) {
gpsPreInit(&masterConfig.gpsConfig);
}
#endif
// Set gyro sampling rate divider before initialization
gyroSetSampleRate(masterConfig.looptime, masterConfig.gyro_lpf, masterConfig.gyroSync, masterConfig.gyroSyncDenominator);
if (!sensorsAutodetect(&masterConfig.sensorAlignmentConfig,
masterConfig.gyro_lpf,
masterConfig.acc_hardware,
masterConfig.mag_hardware,
masterConfig.baro_hardware,
currentProfile->mag_declination)) {
// if gyro was not detected due to whatever reason, we give up now.
failureMode(FAILURE_MISSING_ACC);
}
systemState |= SYSTEM_STATE_SENSORS_READY;
LED1_ON;
LED0_OFF;
for (int i = 0; i < 10; i++) {
LED1_TOGGLE;
LED0_TOGGLE;
delay(25);
BEEP_ON;
delay(25);
BEEP_OFF;
}
LED0_OFF;
LED1_OFF;
#ifdef MAG
if (sensors(SENSOR_MAG))
compassInit();
#endif
imuInit();
mspInit(&masterConfig.serialConfig);
#ifdef USE_CLI
cliInit(&masterConfig.serialConfig);
#endif
failsafeInit(&masterConfig.rxConfig, masterConfig.flight3DConfig.deadband3d_throttle);
rxInit(&masterConfig.rxConfig, currentProfile->modeActivationConditions);
#ifdef GPS
if (feature(FEATURE_GPS)) {
gpsInit(
&masterConfig.serialConfig,
&masterConfig.gpsConfig
);
}
#endif
#ifdef NAV
navigationInit(
&masterConfig.navConfig,
¤tProfile->pidProfile,
¤tProfile->rcControlsConfig,
&masterConfig.rxConfig,
&masterConfig.flight3DConfig,
&masterConfig.escAndServoConfig
);
#endif
#ifdef LED_STRIP
ledStripInit(masterConfig.ledConfigs, masterConfig.colors, masterConfig.modeColors, &masterConfig.specialColors);
if (feature(FEATURE_LED_STRIP)) {
ledStripEnable();
}
#endif
#ifdef TELEMETRY
if (feature(FEATURE_TELEMETRY)) {
telemetryInit();
}
#endif
#ifdef USE_FLASHFS
#ifdef NAZE
if (hardwareRevision == NAZE32_REV5) {
m25p16_init();
}
#elif defined(USE_FLASH_M25P16)
m25p16_init();
#endif
flashfsInit();
#endif
#ifdef USE_SDCARD
bool sdcardUseDMA = false;
sdcardInsertionDetectInit();
#ifdef SDCARD_DMA_CHANNEL_TX
#if defined(LED_STRIP) && defined(WS2811_DMA_CHANNEL)
// Ensure the SPI Tx DMA doesn't overlap with the led strip
sdcardUseDMA = !feature(FEATURE_LED_STRIP) || SDCARD_DMA_CHANNEL_TX != WS2811_DMA_CHANNEL;
#else
sdcardUseDMA = true;
#endif
#endif
sdcard_init(sdcardUseDMA);
afatfs_init();
#endif
#ifdef BLACKBOX
initBlackbox();
#endif
gyroSetCalibrationCycles(CALIBRATING_GYRO_CYCLES);
#ifdef BARO
baroSetCalibrationCycles(CALIBRATING_BARO_CYCLES);
#endif
// start all timers
// TODO - not implemented yet
timerStart();
ENABLE_STATE(SMALL_ANGLE);
DISABLE_ARMING_FLAG(PREVENT_ARMING);
#ifdef SOFTSERIAL_LOOPBACK
// FIXME this is a hack, perhaps add a FUNCTION_LOOPBACK to support it properly
loopbackPort = (serialPort_t*)&(softSerialPorts[0]);
if (!loopbackPort->vTable) {
loopbackPort = openSoftSerial(0, NULL, 19200, SERIAL_NOT_INVERTED);
}
serialPrint(loopbackPort, "LOOPBACK\r\n");
#endif
// Now that everything has powered up the voltage and cell count be determined.
if (feature(FEATURE_VBAT | FEATURE_CURRENT_METER))
batteryInit(&masterConfig.batteryConfig);
#ifdef CJMCU
LED2_ON;
#endif
// Latch active features AGAIN since some may be modified by init().
latchActiveFeatures();
motorControlEnable = true;
systemState |= SYSTEM_STATE_READY;
}
#ifdef SOFTSERIAL_LOOPBACK
void processLoopback(void) {
if (loopbackPort) {
uint8_t bytesWaiting;
while ((bytesWaiting = serialRxBytesWaiting(loopbackPort))) {
uint8_t b = serialRead(loopbackPort);
serialWrite(loopbackPort, b);
};
}
}
#else
#define processLoopback()
#endif
int main(void)
{
init();
/* Setup scheduler */
schedulerInit();
rescheduleTask(TASK_GYROPID, targetLooptime);
setTaskEnabled(TASK_GYROPID, true);
setTaskEnabled(TASK_SERIAL, true);
#ifdef BEEPER
setTaskEnabled(TASK_BEEPER, true);
#endif
setTaskEnabled(TASK_BATTERY, feature(FEATURE_VBAT) || feature(FEATURE_CURRENT_METER));
setTaskEnabled(TASK_RX, true);
#ifdef GPS
setTaskEnabled(TASK_GPS, feature(FEATURE_GPS));
#endif
#ifdef MAG
setTaskEnabled(TASK_COMPASS, sensors(SENSOR_MAG));
#if defined(MPU6500_SPI_INSTANCE) && defined(USE_MAG_AK8963)
// fixme temporary solution for AK6983 via slave I2C on MPU9250
rescheduleTask(TASK_COMPASS, 1000000 / 40);
#endif
#endif
#ifdef BARO
setTaskEnabled(TASK_BARO, sensors(SENSOR_BARO));
#endif
#ifdef SONAR
setTaskEnabled(TASK_SONAR, sensors(SENSOR_SONAR));
#endif
#ifdef DISPLAY
setTaskEnabled(TASK_DISPLAY, feature(FEATURE_DISPLAY));
#endif
#ifdef TELEMETRY
setTaskEnabled(TASK_TELEMETRY, feature(FEATURE_TELEMETRY));
#endif
#ifdef LED_STRIP
setTaskEnabled(TASK_LEDSTRIP, feature(FEATURE_LED_STRIP));
#endif
while (true) {
scheduler();
processLoopback();
}
}
static bool gyroDetect(gyroDev_t *dev, const extiConfig_t *extiConfig)
{
dev->mpuIntExtiConfig = extiConfig;
gyroSensor_e gyroHardware = GYRO_AUTODETECT;
dev->gyroAlign = ALIGN_DEFAULT;
switch(gyroHardware) {
case GYRO_AUTODETECT:
; // fallthrough
case GYRO_MPU6050:
#ifdef USE_GYRO_MPU6050
if (mpu6050GyroDetect(dev)) {
gyroHardware = GYRO_MPU6050;
#ifdef GYRO_MPU6050_ALIGN
dev->gyroAlign = GYRO_MPU6050_ALIGN;
#endif
break;
}
#endif
; // fallthrough
case GYRO_L3G4200D:
#ifdef USE_GYRO_L3G4200D
if (l3g4200dDetect(dev)) {
gyroHardware = GYRO_L3G4200D;
#ifdef GYRO_L3G4200D_ALIGN
dev->gyroAlign = GYRO_L3G4200D_ALIGN;
#endif
break;
}
#endif
; // fallthrough
case GYRO_MPU3050:
#ifdef USE_GYRO_MPU3050
if (mpu3050Detect(dev)) {
gyroHardware = GYRO_MPU3050;
#ifdef GYRO_MPU3050_ALIGN
dev->gyroAlign = GYRO_MPU3050_ALIGN;
#endif
break;
}
#endif
; // fallthrough
case GYRO_L3GD20:
#ifdef USE_GYRO_L3GD20
if (l3gd20Detect(dev)) {
gyroHardware = GYRO_L3GD20;
#ifdef GYRO_L3GD20_ALIGN
dev->gyroAlign = GYRO_L3GD20_ALIGN;
#endif
break;
}
#endif
; // fallthrough
case GYRO_MPU6000:
#ifdef USE_GYRO_SPI_MPU6000
if (mpu6000SpiGyroDetect(dev)) {
gyroHardware = GYRO_MPU6000;
#ifdef GYRO_MPU6000_ALIGN
dev->gyroAlign = GYRO_MPU6000_ALIGN;
#endif
break;
}
#endif
; // fallthrough
case GYRO_MPU6500:
#if defined(USE_GYRO_MPU6500) || defined(USE_GYRO_SPI_MPU6500)
#ifdef USE_GYRO_SPI_MPU6500
if (mpu6500GyroDetect(dev) || mpu6500SpiGyroDetect(dev)) {
#else
if (mpu6500GyroDetect(dev)) {
#endif
gyroHardware = GYRO_MPU6500;
#ifdef GYRO_MPU6500_ALIGN
dev->gyroAlign = GYRO_MPU6500_ALIGN;
#endif
break;
}
#endif
; // fallthrough
case GYRO_FAKE:
#ifdef USE_FAKE_GYRO
if (fakeGyroDetect(dev)) {
gyroHardware = GYRO_FAKE;
break;
}
#endif
; // fallthrough
case GYRO_NONE:
gyroHardware = GYRO_NONE;
}
addBootlogEvent6(BOOT_EVENT_GYRO_DETECTION, BOOT_EVENT_FLAGS_NONE, gyroHardware, 0, 0, 0);
if (gyroHardware == GYRO_NONE) {
return false;
}
detectedSensors[SENSOR_INDEX_GYRO] = gyroHardware;
sensorsSet(SENSOR_GYRO);
return true;
}
bool gyroInit(const gyroConfig_t *gyroConfigToUse)
{
gyroConfig = gyroConfigToUse;
memset(&gyro, 0, sizeof(gyro));
#if defined(USE_GYRO_MPU6050) || defined(USE_GYRO_MPU3050) || defined(USE_GYRO_MPU6500) || defined(USE_GYRO_SPI_MPU6500) || defined(USE_GYRO_SPI_MPU6000) || defined(USE_ACC_MPU6050)
const extiConfig_t *extiConfig = selectMPUIntExtiConfig();
mpuDetect(&gyro.dev);
mpuReset = gyro.dev.mpuConfiguration.reset;
#endif
if (!gyroDetect(&gyro.dev, extiConfig)) {
return false;
}
// After refactoring this function is always called after gyro sampling rate is known, so
// no additional condition is required
// Set gyro sample rate before driver initialisation
gyro.dev.lpf = gyroConfig->gyro_lpf;
gyro.targetLooptime = gyroSetSampleRate(gyroConfig->looptime, gyroConfig->gyro_lpf, gyroConfig->gyroSync, gyroConfig->gyroSyncDenominator);
// driver initialisation
gyro.dev.init(&gyro.dev);
if (gyroConfig->gyro_soft_lpf_hz) {
for (int axis = 0; axis < 3; axis++) {
#ifdef ASYNC_GYRO_PROCESSING
biquadFilterInitLPF(&gyroFilterLPF[axis], gyroConfig->gyro_soft_lpf_hz, getGyroUpdateRate());
#else
biquadFilterInitLPF(&gyroFilterLPF[axis], gyroConfig->gyro_soft_lpf_hz, gyro.targetLooptime);
#endif
}
}
return true;
}