void hal_diag_write_char(char c)
{
#ifdef CYGDBG_DIAG_BUF
diag_putc(c);
if (!enable_diag_uart) return;
#endif // CYGDBG_DIAG_BUF
hal_diag_write_char_serial(c);
}
void hal_diag_write_char(char c)
{
hal_diag_init();
#ifdef DEBUG_DIAG
#ifndef CYG_HAL_STARTUP_ROM
diag_buffer[diag_bp++] = c;
if (diag_bp == sizeof(diag_buffer)) diag_bp = 0;
#endif
#endif
hal_diag_write_char_serial(c);
}
static void gdb_diag_write_char(char c)
{
static char line[100];
static int pos = 0;
// No need to send CRs
if( c == '\r' ) return;
line[pos++] = c;
if( c == '\n' || pos == sizeof(line) )
{
while (1)
{
static char hex[] = "0123456789ABCDEF";
cyg_uint8 csum = 0;
int i;
hal_diag_write_char_serial('$');
hal_diag_write_char_serial('O');
csum += 'O';
for( i = 0; i < pos; i++ )
{
char ch = line[i];
char h = hex[(ch>>4)&0xF];
char l = hex[ch&0xF];
hal_diag_write_char_serial(h);
hal_diag_write_char_serial(l);
csum += h;
csum += l;
}
hal_diag_write_char_serial('#');
hal_diag_write_char_serial(hex[(csum>>4)&0xF]);
hal_diag_write_char_serial(hex[csum&0xF]);
{
char c1;
hal_diag_read_char_serial( &c1 );
if( c1 == '+' ) break;
if( cyg_hal_is_break( &c1, 1 ) )
cyg_hal_user_break( NULL );
}
}
pos = 0;
}
}
void hal_diag_write_char(char c)
{
#ifdef CYG_KERNEL_DIAG_GDB
static char line[100];
static int pos = 0;
// No need to send CRs
if( c == '\r' ) return;
line[pos++] = c;
if( c == '\n' || pos == sizeof(line) )
{
// Disable interrupts. This prevents GDB trying to interrupt us
// while we are in the middle of sending a packet. The serial
// receive interrupt will be seen when we re-enable interrupts
// later.
CYG_INTERRUPT_STATE oldstate;
CYG_BYTE wdcr;
HAL_DISABLE_INTERRUPTS(oldstate);
// Beacuse of problems with NT on the testfarm, we also have
// to disable the watchdog here. This only matters in the
// watchdog tests. And yes, this sends my irony meter off the
// scale too.
HAL_READ_UINT8( 0xC0001002, wdcr );
HAL_WRITE_UINT8( 0xC0001002, wdcr&0x3F );
while(1)
{
static char hex[] = "0123456789ABCDEF";
cyg_uint8 csum = 0;
int i;
hal_diag_write_char_serial('$');
hal_diag_write_char_serial('O');
csum += 'O';
for( i = 0; i < pos; i++ )
{
char ch = line[i];
char h = hex[(ch>>4)&0xF];
char l = hex[ch&0xF];
hal_diag_write_char_serial(h);
hal_diag_write_char_serial(l);
csum += h;
csum += l;
}
hal_diag_write_char_serial('#');
hal_diag_write_char_serial(hex[(csum>>4)&0xF]);
hal_diag_write_char_serial(hex[csum&0xF]);
{
char c1;
hal_diag_read_char_serial( &c1 );
if( c1 == '+' ) break;
if( cyg_hal_is_break( &c1, 1 ) )
cyg_hal_user_break( NULL );
}
}
pos = 0;
// Wait for tx buffer to drain
hal_diag_drain_serial();
// And re-enable interrupts
HAL_RESTORE_INTERRUPTS(oldstate);
HAL_WRITE_UINT8( 0xC0001002, wdcr );
}
void
hal_diag_write_char(char c)
{
static char line[100];
static int pos = 0;
// No need to send CRs
if( c == '\r' ) return;
line[pos++] = c;
if( c == '\n' || pos == sizeof(line) )
{
CYG_INTERRUPT_STATE old;
// Disable interrupts. This prevents GDB trying to interrupt us
// while we are in the middle of sending a packet. The serial
// receive interrupt will be seen when we re-enable interrupts
// later.
#ifdef CYGDBG_HAL_DEBUG_GDB_INCLUDE_STUBS
CYG_HAL_GDB_ENTER_CRITICAL_IO_REGION(old);
#else
HAL_DISABLE_INTERRUPTS(old);
#endif
while(1)
{
static char hex[] = "0123456789ABCDEF";
cyg_uint8 csum = 0;
int i;
char c1;
hal_diag_write_char_serial('$');
hal_diag_write_char_serial('O');
csum += 'O';
for( i = 0; i < pos; i++ )
{
char ch = line[i];
char h = hex[(ch>>4)&0xF];
char l = hex[ch&0xF];
hal_diag_write_char_serial(h);
hal_diag_write_char_serial(l);
csum += h;
csum += l;
}
hal_diag_write_char_serial('#');
hal_diag_write_char_serial(hex[(csum>>4)&0xF]);
hal_diag_write_char_serial(hex[csum&0xF]);
// Wait for the ACK character '+' from GDB here and handle
// receiving a ^C instead. This is the reason for this clause
// being a loop.
if (!hal_diag_read_serial(&c1))
continue; // No response - try sending packet again
if( c1 == '+' )
break; // a good acknowledge
#ifdef CYGDBG_HAL_DEBUG_GDB_BREAK_SUPPORT
cyg_drv_interrupt_acknowledge(__IRQ);
if( c1 == 3 ) {
// Ctrl-C: breakpoint.
cyg_hal_gdb_interrupt (__builtin_return_address(0));
break;
}
#endif
// otherwise, loop round again
}
pos = 0;
// And re-enable interrupts
#ifdef CYGDBG_HAL_DEBUG_GDB_INCLUDE_STUBS
CYG_HAL_GDB_LEAVE_CRITICAL_IO_REGION(old);
#else
HAL_RESTORE_INTERRUPTS(old);
#endif
}
void hal_diag_write_char(char c)
{
static char line[100];
static int pos = 0;
#ifdef CYGDBG_DIAG_BUF
diag_putc(c);
if (!enable_diag_uart) return;
#endif // CYGDBG_DIAG_BUF
// No need to send CRs
if( c == '\r' ) return;
line[pos++] = c;
if( c == '\n' || pos == sizeof(line) )
{
CYG_INTERRUPT_STATE old;
// Disable interrupts. This prevents GDB trying to interrupt us
// while we are in the middle of sending a packet. The serial
// receive interrupt will be seen when we re-enable interrupts
// later.
#ifdef CYGDBG_HAL_DEBUG_GDB_INCLUDE_STUBS
CYG_HAL_GDB_ENTER_CRITICAL_IO_REGION(old);
#else
HAL_DISABLE_INTERRUPTS(old);
#endif
while(1)
{
static char hex[] = "0123456789ABCDEF";
cyg_uint8 csum = 0;
int i;
hal_diag_write_char_serial('$');
hal_diag_write_char_serial('O');
csum += 'O';
for( i = 0; i < pos; i++ )
{
char ch = line[i];
char h = hex[(ch>>4)&0xF];
char l = hex[ch&0xF];
hal_diag_write_char_serial(h);
hal_diag_write_char_serial(l);
csum += h;
csum += l;
}
hal_diag_write_char_serial('#');
hal_diag_write_char_serial(hex[(csum>>4)&0xF]);
hal_diag_write_char_serial(hex[csum&0xF]);
#ifndef CYGDBG_HAL_DEBUG_GDB_BREAK_SUPPORT
// only gobble characters if no interrupt handler to grab ^Cs
// is installed (which is exclusive with device driver use)
// Wait for the ACK character '+' from GDB here and handle
// receiving a ^C instead. This is the reason for this clause
// being a loop.
c = cyg_hal_plf_serial_getc(eppc);
if( c == '+' )
break; // a good acknowledge
#if 0
if( c1 == 3 ) {
// Ctrl-C: breakpoint.
breakpoint();
break;
}
#endif
// otherwise, loop round again
#else
break;
#endif
}
pos = 0;
// And re-enable interrupts
#ifdef CYGDBG_HAL_DEBUG_GDB_INCLUDE_STUBS
CYG_HAL_GDB_LEAVE_CRITICAL_IO_REGION(old);
#else
HAL_RESTORE_INTERRUPTS(old);
#endif
}