void runRusEfi(void) {
#if defined(EFI_CONSOLE_UART_DEVICE)
/*
* Activates the serial driver 1 using the driver default configuration.
* PA9 and PA10 are routed to USART1.
*/
sdStart(&SD1, NULL);
palSetPadMode(GPIOA, 9, PAL_MODE_ALTERNATE(1)); /* USART1 TX. */
palSetPadMode(GPIOA, 10, PAL_MODE_ALTERNATE(1)); /* USART1 RX. */
#endif
/*
* Creates the blinker threads.
*/
chThdCreateStatic(waThread1, sizeof(waThread1), NORMALPRIO, Thread1, NULL);
initMax31855(NULL, max31855_cs);
/*
* Normal main() thread activity, in this demo it does nothing except
* sleeping in a loop and check the button state, when the button is
* pressed the test procedure is launched with output on the serial
* driver 1.
*/
while (true) {
// if (palReadPad(GPIOA, GPIOA_BUTTON))
// TestThread(&SD1);
chThdSleepMilliseconds(50);
printPending();
}
}
void initHardware(Logging *logger, Engine *engine) {
engine_configuration_s *engineConfiguration = engine->engineConfiguration;
efiAssertVoid(engineConfiguration!=NULL, "engineConfiguration");
board_configuration_s *boardConfiguration = &engineConfiguration->bc;
printMsg(logger, "initHardware()");
// todo: enable protection. it's disabled because it takes
// 10 extra seconds to re-flash the chip
//flashProtect();
chMtxInit(&spiMtx);
#if EFI_HISTOGRAMS
/**
* histograms is a data structure for CPU monitor, it does not depend on configuration
*/
initHistogramsModule();
#endif /* EFI_HISTOGRAMS */
/**
* This is so early because we want to init logger
* which would be used while finding trigger synch index
* while config read
*/
initTriggerDecoder();
/**
* We need the LED_ERROR pin even before we read configuration
*/
initPrimaryPins();
if (hasFirmwareError()) {
return;
}
initDataStructures(PASS_ENGINE_PARAMETER_F);
#if EFI_INTERNAL_FLASH
palSetPadMode(CONFIG_RESET_SWITCH_PORT, CONFIG_RESET_SWITCH_PIN, PAL_MODE_INPUT_PULLUP);
initFlash(engine);
/**
* this call reads configuration from flash memory or sets default configuration
* if flash state does not look right.
*/
if (SHOULD_INGORE_FLASH()) {
engineConfiguration->engineType = FORD_ASPIRE_1996;
resetConfigurationExt(logger, engineConfiguration->engineType, engine);
writeToFlash();
} else {
readFromFlash();
}
#else
engineConfiguration->engineType = FORD_ASPIRE_1996;
resetConfigurationExt(logger, engineConfiguration->engineType, engineConfiguration, engineConfiguration2, boardConfiguration);
#endif /* EFI_INTERNAL_FLASH */
if (hasFirmwareError()) {
return;
}
mySetPadMode2("board test", boardConfiguration->boardTestModeJumperPin, PAL_MODE_INPUT_PULLUP);
bool isBoardTestMode_b = GET_BOARD_TEST_MODE_VALUE();
initAdcInputs(isBoardTestMode_b);
if (isBoardTestMode_b) {
// this method never returns
initBoardTest();
}
initRtc();
initOutputPins();
#if EFI_HIP_9011
initHip9011();
#endif /* EFI_HIP_9011 */
#if EFI_MAX_31855
initMax31855(boardConfiguration);
#endif /* EFI_MAX_31855 */
#if EFI_CAN_SUPPORT
initCan();
#endif /* EFI_CAN_SUPPORT */
// init_adc_mcp3208(&adcState, &SPID2);
// requestAdcValue(&adcState, 0);
// todo: figure out better startup logic
initTriggerCentral(engine);
#if EFI_SHAFT_POSITION_INPUT
initShaftPositionInputCapture();
#endif /* EFI_SHAFT_POSITION_INPUT */
initSpiModules(boardConfiguration);
#if EFI_FILE_LOGGING
initMmcCard();
#endif /* EFI_FILE_LOGGING */
// initFixedLeds();
// initBooleanInputs();
#if EFI_UART_GPS
initGps();
#endif
#if ADC_SNIFFER
initAdcDriver();
#endif
#if EFI_HD44780_LCD
// initI2Cmodule();
lcd_HD44780_init();
if (hasFirmwareError())
return;
lcd_HD44780_print_string(VCS_VERSION);
#endif /* EFI_HD44780_LCD */
addConsoleActionII("i2c", sendI2Cbyte);
// while (true) {
// for (int addr = 0x20; addr < 0x28; addr++) {
// sendI2Cbyte(addr, 0);
// int err = i2cGetErrors(&I2CD1);
// print("I2C: err=%x from %d\r\n", err, addr);
// chThdSleepMilliseconds(5);
// sendI2Cbyte(addr, 255);
// chThdSleepMilliseconds(5);
// }
// }
printMsg(logger, "initHardware() OK!");
}
void initHardware(Logging *l) {
efiAssertVoid(CUSTOM_IH_STACK, getRemainingStack(chThdGetSelfX()) > 256, "init h");
sharedLogger = l;
engine_configuration_s *engineConfiguration = engine->engineConfigurationPtr;
efiAssertVoid(CUSTOM_EC_NULL, engineConfiguration!=NULL, "engineConfiguration");
board_configuration_s *boardConfiguration = &engineConfiguration->bc;
printMsg(sharedLogger, "initHardware()");
// todo: enable protection. it's disabled because it takes
// 10 extra seconds to re-flash the chip
//flashProtect();
chMtxObjectInit(&spiMtx);
#if EFI_HISTOGRAMS
/**
* histograms is a data structure for CPU monitor, it does not depend on configuration
*/
initHistogramsModule();
#endif /* EFI_HISTOGRAMS */
/**
* We need the LED_ERROR pin even before we read configuration
*/
initPrimaryPins();
if (hasFirmwareError()) {
return;
}
#if EFI_INTERNAL_FLASH
palSetPadMode(CONFIG_RESET_SWITCH_PORT, CONFIG_RESET_SWITCH_PIN, PAL_MODE_INPUT_PULLUP);
initFlash(sharedLogger);
/**
* this call reads configuration from flash memory or sets default configuration
* if flash state does not look right.
*/
if (SHOULD_INGORE_FLASH()) {
engineConfiguration->engineType = DEFAULT_ENGINE_TYPE;
resetConfigurationExt(sharedLogger, engineConfiguration->engineType PASS_ENGINE_PARAMETER_SUFFIX);
writeToFlashNow();
} else {
readFromFlash();
}
#else
engineConfiguration->engineType = DEFAULT_ENGINE_TYPE;
resetConfigurationExt(sharedLogger, engineConfiguration->engineType PASS_ENGINE_PARAMETER_SUFFIX);
#endif /* EFI_INTERNAL_FLASH */
#if EFI_HD44780_LCD
// initI2Cmodule();
lcd_HD44780_init(sharedLogger);
if (hasFirmwareError())
return;
lcd_HD44780_print_string(VCS_VERSION);
#endif /* EFI_HD44780_LCD */
if (hasFirmwareError()) {
return;
}
#if EFI_SHAFT_POSITION_INPUT || defined(__DOXYGEN__)
initTriggerDecoder();
#endif
bool isBoardTestMode_b;
if (CONFIGB(boardTestModeJumperPin) != GPIO_UNASSIGNED) {
efiSetPadMode("board test", CONFIGB(boardTestModeJumperPin),
PAL_MODE_INPUT_PULLUP);
isBoardTestMode_b = (!efiReadPin(CONFIGB(boardTestModeJumperPin)));
// we can now relese this pin, it is actually used as output sometimes
unmarkPin(CONFIGB(boardTestModeJumperPin));
} else {
isBoardTestMode_b = false;
}
#if HAL_USE_ADC || defined(__DOXYGEN__)
initAdcInputs(isBoardTestMode_b);
#endif
if (isBoardTestMode_b) {
// this method never returns
initBoardTest();
}
initRtc();
initOutputPins();
#if EFI_MAX_31855
initMax31855(sharedLogger, getSpiDevice(CONFIGB(max31855spiDevice)), CONFIGB(max31855_cs));
#endif /* EFI_MAX_31855 */
#if EFI_CAN_SUPPORT
initCan();
#endif /* EFI_CAN_SUPPORT */
// init_adc_mcp3208(&adcState, &SPID2);
// requestAdcValue(&adcState, 0);
#if EFI_SHAFT_POSITION_INPUT || defined(__DOXYGEN__)
// todo: figure out better startup logic
initTriggerCentral(sharedLogger);
#endif /* EFI_SHAFT_POSITION_INPUT */
turnOnHardware(sharedLogger);
#if HAL_USE_SPI || defined(__DOXYGEN__)
initSpiModules(boardConfiguration);
#endif
#if EFI_HIP_9011 || defined(__DOXYGEN__)
initHip9011(sharedLogger);
#endif /* EFI_HIP_9011 */
#if EFI_FILE_LOGGING || defined(__DOXYGEN__)
initMmcCard();
#endif /* EFI_FILE_LOGGING */
#if EFI_MEMS || defined(__DOXYGEN__)
initAccelerometer(PASS_ENGINE_PARAMETER_SIGNATURE);
#endif
// initFixedLeds();
#if EFI_BOSCH_YAW || defined(__DOXYGEN__)
initBoschYawRateSensor();
#endif /* EFI_BOSCH_YAW */
// initBooleanInputs();
#if EFI_UART_GPS || defined(__DOXYGEN__)
initGps();
#endif
#if EFI_SERVO
initServo();
#endif
#if ADC_SNIFFER || defined(__DOXYGEN__)
initAdcDriver();
#endif
#if HAL_USE_I2C || defined(__DOXYGEN__)
addConsoleActionII("i2c", sendI2Cbyte);
#endif
// USBMassStorageDriver UMSD1;
// while (true) {
// for (int addr = 0x20; addr < 0x28; addr++) {
// sendI2Cbyte(addr, 0);
// int err = i2cGetErrors(&I2CD1);
// print("I2C: err=%x from %d\r\n", err, addr);
// chThdSleepMilliseconds(5);
// sendI2Cbyte(addr, 255);
// chThdSleepMilliseconds(5);
// }
// }
#if EFI_VEHICLE_SPEED || defined(__DOXYGEN__)
initVehicleSpeed(sharedLogger);
#endif
#if EFI_CDM_INTEGRATION
cdmIonInit();
#endif
#if HAL_USE_EXT || defined(__DOXYGEN__)
initJoystick(sharedLogger);
#endif
calcFastAdcIndexes();
printMsg(sharedLogger, "initHardware() OK!");
}
