void __init arch_init_irq(void)
{
unsigned int i, cpu;
u64 tmp;
unsigned int imask = STATUSF_IP4 | STATUSF_IP3 | STATUSF_IP2 |
STATUSF_IP1 | STATUSF_IP0;
/* Default everything to IP2 */
/* Start with _high registers which has no bit 0 interrupt source */
for (i = 1; i < BCM1480_NR_IRQS_HALF; i++) { /* was I0 */
for (cpu = 0; cpu < 4; cpu++) {
__raw_writeq(IMR_IP2_VAL,
IOADDR(A_BCM1480_IMR_REGISTER(cpu,
R_BCM1480_IMR_INTERRUPT_MAP_BASE_H) + (i << 3)));
}
}
/* Now do _low registers */
for (i = 0; i < BCM1480_NR_IRQS_HALF; i++) {
for (cpu = 0; cpu < 4; cpu++) {
__raw_writeq(IMR_IP2_VAL,
IOADDR(A_BCM1480_IMR_REGISTER(cpu,
R_BCM1480_IMR_INTERRUPT_MAP_BASE_L) + (i << 3)));
}
}
init_bcm1480_irqs();
/*
* Map the high 16 bits of mailbox_0 registers to IP[3], for
* inter-cpu messages
*/
/* Was I1 */
for (cpu = 0; cpu < 4; cpu++) {
__raw_writeq(IMR_IP3_VAL, IOADDR(A_BCM1480_IMR_REGISTER(cpu, R_BCM1480_IMR_INTERRUPT_MAP_BASE_H) +
(K_BCM1480_INT_MBOX_0_0 << 3)));
}
/* Clear the mailboxes. The firmware may leave them dirty */
for (cpu = 0; cpu < 4; cpu++) {
__raw_writeq(0xffffffffffffffffULL,
IOADDR(A_BCM1480_IMR_REGISTER(cpu, R_BCM1480_IMR_MAILBOX_0_CLR_CPU)));
__raw_writeq(0xffffffffffffffffULL,
IOADDR(A_BCM1480_IMR_REGISTER(cpu, R_BCM1480_IMR_MAILBOX_1_CLR_CPU)));
}
/* Mask everything except the high 16 bit of mailbox_0 registers for all cpus */
tmp = ~((u64) 0) ^ ( (((u64) 1) << K_BCM1480_INT_MBOX_0_0));
for (cpu = 0; cpu < 4; cpu++) {
__raw_writeq(tmp, IOADDR(A_BCM1480_IMR_REGISTER(cpu, R_BCM1480_IMR_INTERRUPT_MASK_H)));
}
tmp = ~((u64) 0);
for (cpu = 0; cpu < 4; cpu++) {
__raw_writeq(tmp, IOADDR(A_BCM1480_IMR_REGISTER(cpu, R_BCM1480_IMR_INTERRUPT_MASK_L)));
}
bcm1480_steal_irq(K_BCM1480_INT_MBOX_0_0);
/*
* Note that the timer interrupts are also mapped, but this is
* done in bcm1480_time_init(). Also, the profiling driver
* does its own management of IP7.
*/
#ifdef CONFIG_KGDB
imask |= STATUSF_IP6;
#endif
/* Enable necessary IPs, disable the rest */
change_c0_status(ST0_IM, imask);
#ifdef CONFIG_KGDB
if (kgdb_flag) {
kgdb_irq = K_BCM1480_INT_UART_0 + kgdb_port;
#ifdef CONFIG_SIBYTE_SB1250_DUART
sb1250_duart_present[kgdb_port] = 0;
#endif
/* Setup uart 1 settings, mapper */
/* QQQ FIXME */
__raw_writeq(M_DUART_IMR_BRK, IO_SPACE_BASE + A_DUART_IMRREG(kgdb_port));
bcm1480_steal_irq(kgdb_irq);
__raw_writeq(IMR_IP6_VAL,
IO_SPACE_BASE + A_BCM1480_IMR_REGISTER(0, R_BCM1480_IMR_INTERRUPT_MAP_BASE_H) +
(kgdb_irq<<3));
bcm1480_unmask_irq(0, kgdb_irq);
#ifdef CONFIG_GDB_CONSOLE
register_gdb_console();
#endif
prom_printf("Waiting for GDB on UART port %d\n", kgdb_port);
set_debug_traps();
breakpoint();
}
#endif
}
void __init arch_init_irq(void)
{
unsigned int i, cpu;
u64 tmp;
unsigned int imask = STATUSF_IP4 | STATUSF_IP3 | STATUSF_IP2 |
STATUSF_IP1 | STATUSF_IP0;
/* Default everything to IP2 */
/* Start with _high registers which has no bit 0 interrupt source */
for (i = 1; i < BCM1480_NR_IRQS_HALF; i++) { /* was I0 */
for (cpu = 0; cpu < 4; cpu++) {
__raw_writeq(IMR_IP2_VAL,
IOADDR(A_BCM1480_IMR_REGISTER(cpu,
R_BCM1480_IMR_INTERRUPT_MAP_BASE_H) + (i << 3)));
}
}
/* Now do _low registers */
for (i = 0; i < BCM1480_NR_IRQS_HALF; i++) {
for (cpu = 0; cpu < 4; cpu++) {
__raw_writeq(IMR_IP2_VAL,
IOADDR(A_BCM1480_IMR_REGISTER(cpu,
R_BCM1480_IMR_INTERRUPT_MAP_BASE_L) + (i << 3)));
}
}
init_bcm1480_irqs();
/*
* Map the high 16 bits of mailbox_0 registers to IP[3], for
* inter-cpu messages
*/
/* Was I1 */
for (cpu = 0; cpu < 4; cpu++) {
__raw_writeq(IMR_IP3_VAL, IOADDR(A_BCM1480_IMR_REGISTER(cpu, R_BCM1480_IMR_INTERRUPT_MAP_BASE_H) +
(K_BCM1480_INT_MBOX_0_0 << 3)));
}
/* Clear the mailboxes. The firmware may leave them dirty */
for (cpu = 0; cpu < 4; cpu++) {
__raw_writeq(0xffffffffffffffffULL,
IOADDR(A_BCM1480_IMR_REGISTER(cpu, R_BCM1480_IMR_MAILBOX_0_CLR_CPU)));
__raw_writeq(0xffffffffffffffffULL,
IOADDR(A_BCM1480_IMR_REGISTER(cpu, R_BCM1480_IMR_MAILBOX_1_CLR_CPU)));
}
/* Mask everything except the high 16 bit of mailbox_0 registers for all cpus */
tmp = ~((u64) 0) ^ ( (((u64) 1) << K_BCM1480_INT_MBOX_0_0));
for (cpu = 0; cpu < 4; cpu++) {
__raw_writeq(tmp, IOADDR(A_BCM1480_IMR_REGISTER(cpu, R_BCM1480_IMR_INTERRUPT_MASK_H)));
}
tmp = ~((u64) 0);
for (cpu = 0; cpu < 4; cpu++) {
__raw_writeq(tmp, IOADDR(A_BCM1480_IMR_REGISTER(cpu, R_BCM1480_IMR_INTERRUPT_MASK_L)));
}
/*
* Note that the timer interrupts are also mapped, but this is
* done in bcm1480_time_init(). Also, the profiling driver
* does its own management of IP7.
*/
/* Enable necessary IPs, disable the rest */
change_c0_status(ST0_IM, imask);
}